sign in sign up
<<
Home , Adhesive

The Professional’s Formula For Success™ 663 Outdoor Carpet

Use for installation of indoor/outdoor carpet in exterior installations only.

• Water-resistant after 5 days • Strong initial grab helps reduce edge curl • No open time required • For immediate installations • Long working time • For large installations • Excellent bond integrity • For permanent installations • Excellent trowelability • Easy to use, easy to trowel ENVIRONMENTAL TECHNOLOGY

U-Notch D=3/32”, W=1/8”, A=1/8” V-Notch D=1/8”, W=1/8”, A=1/16” Smooth-Back Carpet Rough-Back Carpet and All Installations on 108-126 sq. ft. / gal. Rough and on Extremely Porous or 27-31.5 sq. ft. / qt. Rough Concrete 2.5-3 sq. m / L 54-72 sq. ft./ gal. 17.5-20 sq. ft./ qt. 1.3-1.7 sq. m/ L

The W.W. Henry Company 400 Ardex Park Drive Aliquippa, PA 15001 (724) 203-8000 1-800-232-4832 www.wwhenry.com Installation Adhesive is water resistant after five days. Protect from 663 water for five days after installation. Stir any found on the surface into the adhesive, and Outdoor Carpet full spread the adhesive using the proper trowel. A 100% transfer of adhesive into the carpet backing, while Adhesive maintaining full coverage of the substrate, must be obtained. Install carpet or turf immediately into wet adhesive. Do not allow a heavy film to form on surface of the adhesive. If the adhesive dries or skins over, it must be scraped up, and fresh Description adhesive needs to be applied. Cut, fit and reposition within 70 minutes. Working time will vary based on jobsite conditions, HENRY® 663 Outdoor Carpet Adhesive is a “best-in-class” substrate, temperature and humidity. Lift a newly laid area adhesive for exterior installations of indoor/outdoor carpet. occasionally to make sure adhesive is transfering fully to HENRY 663 bonds artificial turf and indoor/outdoor carpet in the back. exterior installations only to concrete, asphalt paving and other clean, sound paving surfaces (not for use with asphalt roofing), After installation, roll the flooring with a 100 lb. roller exterior- or marine-grade decking which is sound and across width and length, as recommended by the flooring not subject to deterioration (not for use with plank decking manufacturer. Stiff carpet should be re-rolled in 2 hours. or treated wood), roughened aluminum boat decks, and Cut and seal all seams as recommended by the abraded fiberglass. Substrates that have been painted, stained carpet manufacturer. or otherwise coated must be tested to ensure compatibility with the adhesive. Clean Up Remove wet adhesive residue with a clean, white cloth Use For dampened with soapy water. Use mineral spirits for dried Indoor/outdoor carpet and artificial turf in exterior installations adhesive residue. When using mineral spirits, carefully follow only. Not for use with vinyl-backed or urethane-backed carpet. the recommendations of the manufacturer, and test a small Not for use with asphalt roofing, plank decking or treated wood. area before proceeding to make sure it does not damage the surface being cleaned. Bonds To Refer to the flooring manufacturer’s specific recommendations for Warranty suitable substrates. Do not use over wallpaper or outdoors. 10-Year Limited HENRY’S BEST WARRANTY. Failure to • Porous: Concrete, asphalt paving and other clean, sound, follow written directions will void the warranty. For complete solid paving surfaces and cementitious underlayments. warranty details, please contact our Customer Service Untreated, exterior or marine-grade plywood decking. Center 1-800-232-4832. * Please note that we cannot be responsible for failures resulting from deterioration of the plywood itself. Do not install Notes over plank decking. Substrates that have been painted, Do not reuse . Dispose of container and adhesive stained, or otherwise coated must be tested to ensure residue in accordance with federal, state and local waste compatibility with adhesive. disposal regulations. Do not flush adhesive down drains. • Non-porous: Abraded fiberglass substrates, roughened • FOR PROFESSIONAL USE ONLY aluminum boat decks. Substrates that have been painted, • Freeze/Thaw Stable to 10°F (-12°C). Avoid lower stained, or otherwise coated must be tested to ensure temperatures or multiple freeze/thaw cycles compatibility with adhesive. Do not install over rubber or • is 1 year if unopened asphalt roofing. • VOC content: 76 g/L; calculated & reported, SCAQMD 1168 Preparation Precautions • This adhesive is for outdoor use only. Carefully read and follow all precautions and warnings on the product . For complete safety information, please • Refer to the flooring manufacturer’s specific refer to the Material Safety Data Sheet (MSDS) available at recommendations. www.wwhenry.com.

• Acceptable installation temperatures range from 65°F (18°C) to 100°F (38°C). Made in the USA by The W. W. Henry Company, • Substrate must be sound, smooth and flat. Ensure that the Aliquippa, PA 15001 substrate is solid and securely fixed to provide a rigid base © 2012 W.W. HENRY, L.P. All rights reserved. free of undue flex. All loose substrates must be re-nailed or bonded properly to create a sound surface.

• Substrate must be clean and dry. Mechanically remove dirt, wax, grease, oils, curing compounds and all foreign matter that would interfere with proper . HT125 (09/28/12)