DOCSLIB.ORG

PSE&G Information and Requirements for Electric Service

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
PSE&G Information and Requirements for Electric Service Information and Requirements for Electric Service Rev 4.03 Manual Owner: James Duswalt November 24, 2020 This Page Intentionally Blank October 17, 2019 – Rev 4.02 Record of Revisions Revision Sections Revision Date Reason for Revision Number Revised REV 01 June 1, 2005 All Revised entire Information and Requirements for Electric Service Manual. REV 02 January 6, 2006 Chapters 1, 2, 4, Additional material in Chapters 1, 2, 4, 6 and Appendix pages A-19, 51, 89 6 and Appendix and a new table on A-90. REV 02.01 November 30, 2006 Appendix Change graphic in Exhibit 19B. REV 02.02 April 23, 2008 Chapter 2, Title Typo in Table 2-2, change Manual Owner. Page REV 3.00 May 31, 2014 All Complete review of entire manual. REV 3.01 January 15, 2017 Chapters 1, 5, 6, Chapter 1 – Updated abbreviations in Section 1 and 3.1. 9, 10, 11 and Chapter 5 – Updated Section 3, Bulletin 16-066. Index Chapter 6 – Updated Figure 6.1 Chapter 9 – Updated abbreviations in Section 2. Chapter 10 – Updated Table 10-7, Bulletin 16-034. Updated Figures 10.9, 10.37, 10.38, 10.42, 10.43 and 10.44, Bulletin 16-066. Chapter 11 – Added New Chapter 11 – General Specification for Service to High-Rise Buildings, Bulletin 16-079. Index – Updated Index. REV 4.00 May 18, 2018 All Cover-to-cover review of entire manual completed in 2018 Implemented new template for entire manual Created a Forms chapter before the Index. Chapter 1: • Updated Section 1 – Purpose. • Updated Section 2 – Clarifications. • Deleted Section 3.6 – Designated Growth Area. • Changed title of Section 3.16 from Metalclad Switchgear to Metal Enclosed Switchgear. • Deleted Section 3.18 – Non-Growth Area. • Updated Section 4 – Ownership, Maintenance and Removal of Apparatus Provided by or for PSE&G. • Updated Section 8, paragraph 1. • Updated Section 13 and changed title from Expediting Electric Service to Pre-Requisites for Electric Service. • Deleted Section 16 – Smart Growth Related Customer Charges and Contributions. Chapter 2: • Updated Table 2-1. • Updated Section 2 – Service from the Primary System. Chapter 3: • Deleted Table 3-3 from Section 2.2. • Updated Section 3, paragraph 3. Record of Revisions October 17, 2019 – Rev 4.02 Information and Requirements for Electric Service iii Revision Sections Revision Date Reason for Revision Number Revised REV 4.00 May 18, 2018 All • Updated Section 4, paragraphs 2, 4 and 6. Cont’d • Updated Section 5, paragraph 3. • Updated Section 6, paragraphs 1 and 4. • Updated Section 7. • Updated Section 8, paragraph 1. • Updated Section 9. • Updated Section 10, introductory paragraph and paragraph 2. • Updated Section 11, introductory paragraph and paragraphs 1, 2 and 7. Deleted paragraphs 8 and 9. Chapter 4: • Updated Section 1, paragraphs 1 and 4. • Added paragraph 7 to Section 2. • Updated Section 3, paragraph 2. • Updated Section 4, paragraph 4. • Updated Section 5, paragraph 1. • Updated Section 6, paragraph 2, 3, and 5. Deleted paragraph 6 and renumbered subsequent paragraphs. • Updated Section 7, paragraph 4. • Updated Section 8, paragraph 2, 3 and 5 Chapter 5: • Updated Section 1, paragraph 7. Added new paragraph 10 and renumbered subsequent paragraphs. • Updated Section 2, paragraphs 2, 5, 7, 8, 9 and 10. • Updated Section 3, paragraphs 8, 10 and 11. Chapter 6: • Added new paragraph 5 to Section 2 and renumbered subsequent paragraphs. • Updated Section 7, paragraph 5 and added paragraph 10. • Added “Fire Pumps” the Section 8 heading and paragraphs 1 and 3. • Updated Section 12, paragraph 4. Added new paragraph 6. • Updated Section 15. Moved paragraph 3 to paragraph 1 and added paragraph 13. • Added Section 16. Chapter 7: • Converted all forms to a standard format. Created fillable forms. • Updated Sections 1.1 and 1.2. Chapter 8: • Updated Southern Construction Inquiry phone number ins Table 8-1. • Removed Division Office phone numbers in Table 8-2. Chapter 9: • Spelled out meaning of PJM in definition of PJM. • Updated any occurrence of NJAC to N.J.A.C. • Added Figures 9.1 and 9.2. • Updated Section 4.5 and added Section 4.7. Record of Revisions iv Information and Requirements for Electric Service October 17, 2019 – Rev 4.02 Revision Sections Revision Date Reason for Revision Number Revised REV 4.00 May 18, 2018 All Chapter 10: Cont’d • Updated reference from Chapter 1 Section 16 to Chapter 1 Section 17. • Updated Section 1.1, paragraph 2. Added paragraph 3. • Added note for F, updated Hand added I in the notes for Figure 10.1 and updated note 2. • Inserted Section 2 – Grouped Meter Mounting Equipment Specifications and Figure 10.2. Renumbered subsequent sections and figures. • Updated notes 3, 6 and 11 in the notes for Figures 10.4, 10.5 and 10.6. • Updated notes 9, 12 and 13 in the notes for Figures 10.8, and 10.9. • Updated notes 3, and 7 in the notes for Figures 10.11, and 10.12. • Updated Section 9.1, paragraphs 4, 5, 6, 13, 15 and 16, and removed 3-12 in. conduit diameter from Table 10-2. • Updated note 4 under Customer shall in the notes for Figures 10.16, 10.17 and 10.18. • Added notes 4 and 5 under Customer shall in the notes for Figure 10.19. • Updated notes 3, and 6 in the notes for Figure 10.26. • Updated title of Figure 10.27 to >801 A and updated notes 6, 7 and 11. • Updated notes 6, and 10 and added note 12 in the notes for Figure 10.28. • Updated note 1 under PSE&G will and updated notes 6 and 10, and added note 12 under Customer shall in the notes for Figure 10.29. • Added /Switchgear to the end of Section 18 heading. • Updated note 9 in the notes for Figure 10.30. • Added /Switchgear to the end of Section 19 heading and added > before 801 A. Updated note 4 for Figure 10.31. • Updated note 10 in the notes for Figure 10.31. • Updated notes 1, 2 and 3 in Section 21.1.1. • Updated Section 21.1.3. • Updated Section 25.2 paragraphs 1 and 4. • Updated first paragraph under Section 25.4 • Updated notes 4, 7, 9, and 10 and added note 15 in notes for Figure 10.38. • Updated Section 27 to 300 kVA and below. • Updated Section 27.1 and 27.3. • Deleted Figure – Fiberglass Pad Three-Phase Padmounted Transformers (500 kVA and below) – Type II (Highline Previous Design Type II Pad). • Updated Figure 10.39 title to 300 kVA and below. • Updated Section 28.2, paragraph 1. • Deleted “– Overhead Zones” from the end of Section 29 heading. • Added bullet to Section 29.1 paragraph 3. • Added “For Overhead Type Transformers” to Section 29.2 heading and updated paragraphs 2, 3, 4, 6, 8 and 9. • Deleted note 5 in notes for Figures 10.43 and 10.44. • Changed Figure “Vault Requirements – Customer-Installed Transformer Vault – Network Type Vaults Only” to Section 29.3. • Deleted figure “Vault Requirements – Customer-Installed Transformer Vault – Non-Network Type Vaults Only.” • Added Figures 10.46 and 10.47. • Updated Section 30.1 paragraph 2. Record of Revisions October 17, 2019 – Rev 4.02 Information and Requirements for Electric Service v Revision Sections Revision Date Reason for Revision Number Revised REV 4.00 May 18, 2018 All • Updated Section 30.3 paragraph 2. Cont’d • Updated Figures 10.1, 10.8, 10.11, 10.12, 10.13, 10.16, 10.17, 10.18, 10.19, 10.21, 10.23, 10.25, 10.28, 10.29, 10.30, 10.34, 10.39, 10.40, 10.41, 10.43, 10.44, 10.46 and 10.48. • Deleted Figure “Elevated Pad Specs – Installations in Flood Areas.” • Updated Table 10-7. Chapter 11: • Updated Section 1. • Updated Section 3.2, paragraph 4. • Updated Section 4.1 • Updated Section 8, paragraph 3. • Updated Figure 11.1. REV 4.01 November 30. 2018 Title page, TOC, Introduction – Updated sample reference and Section 8. Introduction, Chapter 3 – Updated Section 3 number 4 and Section 4 number 7. Removed Chapters 3, 4, 6, “open” from “120/240 three-phase four-wire open delta services.” from the 8, 10 and 11. last sentence of each paragraph. Chapter 4 – Updated Section 6 number 5, 1st bullet to “265/460 V” from “265/240V.” Chapter 6 – Section 16.2 – Added PSE&G – Central Sub Division Headquarters 72 W. Jersey Street, Elizabeth, NJ 07202, Patricia D'Alia (908) 558-7520 Fax (908) 353-7642. Chapter 8 – Table 8-1– added Electric Division of “M” to municipality of Hackensack and updated the Electric Division in the municipalities of Perth Amboy, Woodbridge, North Plainfield, Watchung and Plainfield from “CS” to “C.” Chapter 10 – Updated Figure 10.1 Notes. Updated Section 21.1.3 – removed “open” from “120/240 three-phase, four-wire open delta services.” Added “(primary)” and “(secondary)” to Figure 10.35 Note – General number 1. Chapter 11 – Section 2 – updated definition of “Internal Distribution System.” Section 4.1.1 changed “216Y/125” to “208Y/120” for customer requirements. Section 9 changed “216Y/125” to “208Y/120.” Updated Figure 1.1. Record of Revisions vi Information and Requirements for Electric Service October 17, 2019 – Rev 4.02 November 24, 2020 – Rev 4.03 Revision Sections Revision Date Reason for Revision Number Revised REV 4.02 October 17, 2019 Title page, TOC, Chapter 1 – Updated reference from N.J.A.C. 14:5-4.1 to N.J.A.C 14:3-8.4 in LOF, LOT, List of Sections 3.3 and 6 paragraph 5. Forms, Chapter 3 – Updated reference from N.J.A.C.
Load more

Recommended publications
  • Myth, Metatext, Continuity and Cataclysm in Dc Comics’ Crisis on Infinite Earths
    WORLDS WILL LIVE, WORLDS WILL DIE: MYTH, METATEXT, CONTINUITY AND CATACLYSM IN DC COMICS’ CRISIS ON INFINITE EARTHS Adam C. Murdough A Thesis Submitted to the Graduate College of Bowling Green State University in partial fulfillment of the requirements for the degree of MASTER OF ARTS August 2006 Committee: Angela Nelson, Advisor Marilyn Motz Jeremy Wallach ii ABSTRACT Angela Nelson, Advisor In 1985-86, DC Comics launched an extensive campaign to revamp and revise its most important superhero characters for a new era. In many cases, this involved streamlining, retouching, or completely overhauling the characters’ fictional back-stories, while similarly renovating the shared fictional context in which their adventures take place, “the DC Universe.” To accomplish this act of revisionist history, DC resorted to a text-based performative gesture, Crisis on Infinite Earths. This thesis analyzes the impact of this singular text and the phenomena it inspired on the comic-book industry and the DC Comics fan community. The first chapter explains the nature and importance of the convention of “continuity” (i.e., intertextual diegetic storytelling, unfolding progressively over time) in superhero comics, identifying superhero fans’ attachment to continuity as a source of reading pleasure and cultural expressivity as the key factor informing the creation of the Crisis on Infinite Earths text. The second chapter consists of an eschatological reading of the text itself, in which it is argued that Crisis on Infinite Earths combines self-reflexive metafiction with the ideologically inflected symbolic language of apocalypse myth to provide DC Comics fans with a textual "rite of transition," to win their acceptance for DC’s mid-1980s project of self- rehistoricization and renewal.
    [Show full text]
  • New Microsoft Excel Worksheet (2).Xlsx
    Knowledge Assessment ( Written Test) QP Name - Assistant electrician QP Code:CON/Q0602 Total marks: 210 marks Duration: 90 minutes Each NOS carries 30 marks Infrastructure: Classroom, Benches, Pens, pencils Marks CON/N0602: Select and use hand tools, power tools, and electrical devices relevant to construction electrical works 1 Which device is used to measure current in a circuit? 4 a. Voltmeter b. Ammeter c. Tester d. Megger 4 2 Identify the item form the image below? a. Wattmeter b. Digital Multi meter c. Energy meter d. Analog multi meter 3 Which device is used to avoid overload current in a circuit? 4 a. Residual current circuit breaker b. Miniature circuit breaker c. Earth Leakage circuit breaker d. Molded Case circuit breaker 4 Identify the tool form the image below? 4 a. Channel loch plier b. Combination plier c. Nose plier d. Snippers 5 Which of the following is an ideal instrument used to measure the thickness of conduit? 4 a. Vernier Caliper b. Multi meter c. Measuring tape d. Total station 6 Identify the item form the image below? 5 a. Semi enclosed or re-wire able fuse b. Cartridge type fuse c. D type fuse d. Link type fuse 7 Which of the following tools is used to strip the insulation of cable? 5 a. Plier b. Scissor c. Splicer d. Tester CON/N0603: Install temporary lighting arrangement at construction sites Marks 8 What is the maximum number of 1sq.mm wires that can be drawn through a 25mm diameter conduit 4 a. 5 b. 2 c. 4 d.
    [Show full text]
  • Guideline on Through Penetration Firestopping
    GUIDELINE ON THROUGH-PENETRATION FIRESTOPPING SECOND EDITION – AUGUST 2007 SHEET METAL AND AIR CONDITIONING CONTRACTORS’ NATIONAL ASSOCIATION, INC. 4201 Lafayette Center Drive Chantilly, VA 20151-1209 www.smacna.org GUIDELINE ON THROUGH-PENETRATION FIRESTOPPING Copyright © SMACNA 2007 All Rights Reserved by SHEET METAL AND AIR CONDITIONING CONTRACTORS’ NATIONAL ASSOCIATION, INC. 4201 Lafayette Center Drive Chantilly, VA 20151-1209 Printed in the U.S.A. FIRST EDITION – NOVEMBER 1996 SECOND EDITION – AUGUST 2007 Except as allowed in the Notice to Users and in certain licensing contracts, no part of this book may be reproduced, stored in a retrievable system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. FOREWORD This technical guide was prepared in response to increasing concerns over the requirements for through-penetration firestopping as mandated by codes, specified by system designers, and required by code officials and/or other authorities having jurisdiction. The language in the model codes, the definitions used, and the expectations of local code authorities varies widely among the model codes and has caused confusion in the building construction industry. Contractors are often forced to bear the brunt of inadequate or confusing specifications, misunderstandings of code requirements, and lack of adequate plan review prior to construction. This guide contains descriptions, illustrations, definitions, recommendations on industry practices, designations of responsibility, references to other documents and guidance on plan and specification requirements. It is intended to be a generic educational tool for use by all parties to the construction process. Firestopping Guideline • Second Edition iii FIRE AND SMOKE CONTROL COMMITTEE Phillip E.
    [Show full text]
  • Commercial Conduit Rules and Regulations
    Exhibit C – Commercial Conduit Rules and Regulations Electric Engineering Division COMMERCIAL CONDUIT RULES AND REGULATIONS S:\COO_ACM_US_Electric_Telecommunications\COO_ET_Engineering\Conduit Policies C-1 Exhibit C – Commercial Conduit Rules and Regulations 1805 NE 30th Ave., Bldg. 400 Ocala, FL 34470-4875 Phone: (352) 351-6620 Fax: (352 ) 401-6961 Electric Engineering Division Dear Developer: Over the next few months, the City of Ocala Utility Services (OUS) will be working closely with you and your contractors to install the electrical conduit system for your project. We in the Electric Engineering Division are looking forward to working with your contractors and want the installation to proceed as smooth as possible. Attached, please find the OUS Commercial Conduit Rules and Regulations for use by your electrical conduit contractor. If the contractor has any questions that are not addressed in this guide, please contact the OUS representative responsible for the project. Respectfully Ocala Utility Services Engineering Division C-2 Exhibit C – Commercial Conduit Rules and Regulations TABLE OF CONTENTS i. LETTER TO DEVELOPER ........................................................................................... 2 I. RULES AND REGULATIONS A. TABLE OF CONTENTS ....................................................................................... 3 B. TERMS AND DEFINITIONS ............................................................................... 4 C. DEVELOPER’S RESPONSIBILITIES ...............................................................
    [Show full text]
  • Section 16050 - Basic Electrical Materials and Methods
    Revised 10/03/19 SPECIFICATIONS - DETAILED PROVISIONS Section 16050 - Basic Electrical Materials and Methods C O N T E N T S PART 1 - GENERAL ............................................................................................................................. 1 1.01 SCOPE ........................................................................................................................................ 1 1.02 RELATED SECTIONS ................................................................................................................... 1 1.03 STANDARDS AND CODES ......................................................................................................... 1 1.04 SUBMITTALS ............................................................................................................................. 3 1.05 COORDINATION OF WORK AND TRADES ................................................................................ 4 1.06 DELIVERY, STORAGE, AND HANDLING……………………………………………………………………………….. 5 PART 2 - PRODUCTS .......................................................................................................................... 5 2.01 GENERAL ................................................................................................................................... 5 2.02 CONDUCTORS AND CABLES ..................................................................................................... 6 2.03 CONDUCTOR AND CABLE CONNECTORS ................................................................................
    [Show full text]
  • Specification 270528 Interior Communications Pathways
    GUIDELINES HAS/PDC/Design Division Project Title Houston, Texas Proj./CIP No. (These Guidelines are basic minimum criteria to be met in preparing the final specifications for this section, which is the responsibility of the Designer/Contractor/Installation Team.) SECTION 270528 INTERIOR COMMUNICATION PATHWAYS (REV.01-23-2020-SJS) PART 1 GENERAL 1.01 PROJECT SCOPE SUMMARY Designer shall provide a detailed narrative/scope of the tasks to be performed under this specification sections. 1.02 SECTIONS INCLUDES A. This section includes specifications for the installation of interior communications pathways. B. Related Documents: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division - 1 Specification sections, apply to the work of this section. C. Interior Communication Pathways are defined to include, but are not limited to innerduct, flexible multi-cell innerduct, conduit, pull boxes, cable/j-hooks, cable trays, supports, accessories, associated hardware and fire stopping materials. 1.03 REFERENCES A. Related Sections: Use these Specifications for all related work not specifically covered in this specification. 1. Section 270526: Telecommunication Grounding and Bonding 2. Section 270543: Exterior Communication Pathways 3. Section 270553: Identification and Labeling of Communication Infrastructure 4. Section 271100: Communication Cabinets and Equipment Rooms 5. Section 271300: Backbone and Riser Media Infrastructure 6. Section 271500: Horizontal Media Infrastructure 7. Section 272100: Data Communication Network Equipment 8. Section 272200: PC, Laptop, Servers and Equipment 9. Section 275113: Audio Communication System 10. Section 281300: Access Control System 11. Section 232313: Video Surveillance Control and Management System B. American National Standards Institute / Telecommunications Industry Association / Electronic Industries Alliance (ANSI/TIA/EIA): Most current standard revision 1.
    [Show full text]
  • Installation Guide
    Installation Preparation of the hood for installation: To facilitate the installation it is recommended to remove the panel before installing the hood. Attention! Keep both hands on the panel when disassembling or reassembling it into place to prevent it from falling and causing damage to persons or property. Disassembly: - Pull the panel (FRONT SIDE) firmly down, - Push the small lever, located in the right side of the panel, to the left, - Unhook it from the rear joints. 8 Installation - Ducting version 1. Pre-installation calculations 2. Preparation of mounting surface K = Kitchen Height Installing supports above ceiling drywall. C = Counter Height (36" standard) P = Prefered Height of Hood Bottom above counter (Recommended 24”-30”) H = Hood height your installation H = K – C – P a) Select a hood preference height P that is comfortable for the user. (from 24” to 30“). b) Calculate Hood height your installation H = K-C-P. c) Confirm that H is within the range of min to max H found for your model (See “Dimensions and clearances” paragraph). If not adjust your installation. Note: Take into consideration the hood depth; the hood could be much deeper than the cooktop. a. Mark center lines of cooktop or range on ceiling above. Use centerlines marked on ceiling to position the mounting template. Note location of hood front (that indicated with a printed arrow), side, and mounting holes indicated on template. Note: Remember that printed arrow on template corresponds to front of the hood and consequently to side where control panels will be located at the end of installation) b.
    [Show full text]
  • Electrical Conduits
    Electric Level 5 Electrical Conduits What’s it all About? Electrical conduits refer to an electrical system used to protect and provide route of electrical wiring. Electrical conduits are made of metal, plastic, or fiber and could be rigid or flexible. Conduits must be installed by following standard regulations, as those provided by the manufacturer and the National Electrical Code (NEC). Keys to Remember • The 2017 NEC covers 12 types of conduits. Articles 342 through 362 specify use, installation, and construction specifications. • Fill rates, or how many wires can be put in the conduit, is covered in the 2017 NEC Annex C. • Sizing - Conduit tubing uses Outside Dimensions (OD); conduit piping uses Nominal Pipe Size (NPS). Sizes range from 3/8” to 6”. • With any wiring project, safety for people and property is most important. Any metallic conduit should be grounded/bonded to the electrical grounding system. For the Project • Material List with Costs • References • Diagrams • Planning and Research • Dimensions • Title and Labels • Pictures (if exhibiting a report or poster) • Record Sheet Nine Common Types of Electrical Conduit 1. Galvanized Rigid Conduit A conduit made from galvanized steel tubing is commonly referred to as a rigid conduit. The thickness of a galvanized rigid (GR) conduit protects the electrical wiring from being hit and allows it to be threaded. 2. Electrical Metallic Tubing An electrical metallic tubing (EMT) conduit is made of steel; in some cases aluminum is also used. EMT is cheaper than a galvanized rigid conduit and lighter than a GR conduit. EMT is also a very popular material because it can be bent to specific radius and directions.
    [Show full text]
  • DC Comics Jumpchain CYOA
    DC Comics Jumpchain CYOA CYOA written by [text removed] [text removed] [text removed] cause I didn’t lol The lists of superpowers and weaknesses are taken from the DC Wiki, and have been reproduced here for ease of access. Some entries have been removed, added, or modified to better fit this format. The DC universe is long and storied one, in more ways than one. It’s a universe filled with adventure around every corner, not least among them on Earth, an unassuming but cosmically significant planet out of the way of most space territories. Heroes and villains, from the bottom of the Dark Multiverse to the top of the Monitor Sphere, endlessly struggle for justice, for power, and for control over the fate of the very multiverse itself. You start with 1000 Cape Points (CP). Discounted options are 50% off. Discounts only apply once per purchase. Free options are not mandatory. Continuity === === === === === Continuity doesn't change during your time here, since each continuity has a past and a future unconnected to the Crises. If you're in Post-Crisis you'll blow right through 2011 instead of seeing Flashpoint. This changes if you take the relevant scenarios. You can choose your starting date. Early Golden Age (eGA) Default Start Date: 1939 The original timeline, the one where it all began. Superman can leap tall buildings in a single bound, while other characters like Batman, Dr. Occult, and Sandman have just debuted in their respective cities. This continuity occurred in the late 1930s, and takes place in a single universe.
    [Show full text]
  • Answer the Purpose: 4
    Page 26 1. CONDUCTORS Conductors are defined as materials that easily allow the flow of _________. Metals are _______ conductors while insulators are ______ . The 2 common metals used for conductors in the electrical trade are: ___________ and ______________. Aluminium has become more prevalent for larger C.S.A. conductors as it is cheaper and lighter but more brittle than copper. Current/ Copper/ Aluminium Thermoplastic-sheathed cable (TPS) consists of an outer toughened sheath of polyvinyl chloride (PVC) (the thermoplastic element) covering one or more individual cables which are PVC insulated annealed copper conductors. It is a commonly used type of wiring for residential and light commercial construction in many countries. The flat version of the cable with two insulated conductors and an uninsulated earth conductor all within the outer sheath is referred to as twin and earth. In mainland Europe, a round equivalent is more common. Flat cables (or festoon cables) are made in PVC and Neoprene and are used as trailing cables for cranes, open filed conveyors and shelve service devices. Flat cables offer the advantages of extremely small bending radius’s, high flexibility and minimum wastage of space. Thermoplastic-sheathed cable (TPS) consists of an outer toughened sheath of polyvinyl chloride (PVC) (the thermoplastic element) covering one or more individual cables which are PVC insulated annealed copper conductors. It is a commonly used type of wiring for residential and light commercial construction in many countries. The flat version of the cable with two insulated conductors and an uninsulated earth conductor all within the outer sheath is referred to as twin and earth.
    [Show full text]
  • Electric Service Rules
    2021 Electric Service Rules GENERAL INFORMATION TEMPORARY SERVICES OVERHEAD SERVICES UNDERGROUND SERVICES DISTRIBUTED GENERATION METERING HUD MANUFACTURED HOMES FARM SERVICES UTILITY/CATV SERVICES PRIMARY SERVICES SPECIAL SERVICES AND MOTORS OPTIONAL STANDBY GENERATION CLEARANCES GROUNDING AND BONDING ELECTRIC VEHICLES © 2021 Alliant Energy 885247 11/20 AM Version 17 Updates to this manual may be necessary throughout the year. Please see www.alliantenergy.com/servicemanuals for the most up-to-date information. ELECTRIC SERVICE RULES Issued Jan 2021 C a l l B e f o r e Y o u D i g DIGGERS HOTLINE, Telephone Numbers, Alliant Energy Web Site Information & Cable Locating Services ALLIANT ENERGY IP&L/WP&L TELEPHONE NUMBERS Electric Service: 1-800-862-6222 or 1-800-ALLIANT Outage Reporting: 1-877-740-5050 or 1-800-ALLIANT PRE-EXCAVATION TELEPHONE NUMBERS Pre-Excavation Call Number All Areas - 811 Iowa – Iowa One Call: 1-800-292-8989 Wisconsin – Diggers Hotline: 1-800-242-8511 ALLIANT ENERGY WEBSITE Key in Web Site www.alliantenergy.com/servicemanuals C a l l B e f o r e Y o u D i g Page i ELECTRIC SERVICE RULES Issued Jan 2021 TABLE OF CONTENTS - ESR Revision Date: January 2021 CHAPTER 1 – GENERAL INFORMATION...... UPDATED JULY 2021 Page 100. General ...................................................................................................................... 1-1 101. Purpose ..................................................................................................................... 1-1 102. Scope .......................................................................................................................
    [Show full text]
  • Johns Hopkins Enterprise Low Voltage Cabling Standards - Unabridged
    JOHNS HOPKINS INSTITUTIONS Johns Hopkins Enterprise Low Voltage Cabling Standards - Unabridged Approved by the ICSC, Revisions from Standard from 2005 May 2015 JOHNS HOPKINS UNIVERSITY Shelly Hoffmaster, RCDD Johns Hopkins Medicine Network Project Manager Greg Asman, RCDD Network Project Manager IT@JH-Enterprise Networking To: Architects and Consultants Re: Use of Johns Hopkins Cable Plant Design and Construction Specification Date: March 2, 2015 Intended Use This is a general specification for use in developing project construction documents for the information transport systems infrastructure for the Johns Hopkins Institutions. The specification as presented here includes all possible elements for an ITS installation. Designers and Architects will need to select and modify sections of this specification as required for their project. Not all divisions and sections will be applied to every project. Not all paragraphs of any given section may apply to a given project. System variables (e.g. copper pair counts, fiber backbone size) may be displayed as an example within this general specification. When generating a project specification: Designers and Architects will need to submit specifications based on this document to the appropriate Johns Hopkins group for approval of options selected from this specification. Designers and Architects shall not add language to this specification when generating a project- specific specification without approval of Johns Hopkins. When issuing to Contractors for Installation: The Contractor shall be aware of but not focus on the “Design Requirements” section within each specification section used. Contractors are to provide bid proposals per the “Products” sections and install per the “Execution” sections. Errors and omissions within this document shall be reported for correction in the general specification.
    [Show full text]