DOCSLIB.ORG

Patterns & Installation Guide Patterns

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Patterns & Installation Guide Patterns PROPER STORAGE Primed lumber should be stored off the ground in a covered Siskiyou Reserve Premium Wood Siding is building and out of the weather. For best results, let wood products reach an equilibrium with the local climate by storing them for at specifically formulated to be the ultimate in siding, least fifteen days in a well-ventilated shelter. fascia and trim. Being made of quality clear, finger-jointed Western Red Cedar, this product is STORAGE DOs STORAGE DON’Ts naturally designed for exterior use. DO store wood in a garage DON’T keep wood wrapped or shed with adequate air tightly in plastic covers. The RESERVE Line is specially manufactured circulation for best protection Loosen wrappers at job site to from the elements. permit air circulation. and treated to create the highest quality product available. Using state-of-the-art application and DO keep wood dry. If it can’t DON’T leave wood in the sun be kept under a roof, protect or covered with dark plastic. curing equipment, their premium Western Red it with a water proof cover. The dark cover will attract heat Cedar stock is made to last for many generations. Make sure the cover is secure and cause excessive drying. but loose enough to permit air It is a beautiful, durable product that is ready for circulation. DON’T let wood get wet or installation and final painting the moment it reaches dirty. When storing lumber DO store wood off the ground near the ground, place a the craftsman. and protected from dirt, plastic cover over soil to moisture, direct sunlight and minimize moisture absorption. extreme heat. The two coat process begins with an alkyd oil sealer to block tannin migration. This step is NAILING DOs followed by a high-performance acrylic primer - Ready for final painting as soon as it’s installed. DO use non-corrosive nails DO use a drainable weather to avoid nail stains; stainless barrier such as DuPont™ steel or top quality, hot-dipped Tyvek® DrainWrap™. The result: RESERVE quality, inside and out & galvanized. DO use bevel cuts at half PRODUCT IS BACKED WITH A 50 YEAR LIMITED WARRANTY! DO use ring-shanked wood joints as this can minimize the Ask your OrePac Representative for details. siding nails. appearance of gaps due to shrinkage. DO use properly sized nails. Shank should penetrate DO spot prime trim ends prior A NATURAL PRODUCT 1-1/2” into framing members to installation. Wood is a natural product, so individual pieces or a combination of framing vary in performance. Wood’s performance members and solid wood DO remember that saw- sheathing. If sheathing is not textured surface perform better depends on many critical factors including: solid wood, longer nails are and hold finishes longer. necessary. DO remember to spot prime · Storage and handling · Structure design DO pre-drill holes to prevent nail locations, scuffed areas · Craftsmen’s skills · Use of other materials splitting when nailing into and other areas showing bare corners or near ends. wood with a high-quality, oil- · Exposure to weather based, stain-blocking primer DO use a wood-based after installation. While our 2-coat priming process is formulated to sheathing. control stains, some staining may occur due to the NAILING DON’Ts wood’s natural properties and site conditions. The PATTERNS & best way to avoid extractive stains is to follow all DON’T use common iron, DON’T nail through tip of copper, cement-coated, undercourse on lapped siding. handling and finishing instructions. Doing so will electroplated or poor quality This causes splitting. help to produce good performance under most INSTALLATION galvanized nails. These will cause stains. DON’T nail to sheathing only. conditions, however it will not guarantee flawless This will not hold lumber in performance and no warranties, expressed or DON’T use casing, finishing place. GUIDE or other small-head nails, implied, are given. Due to conditions beyond our except for blind nailing tongue control, Siskiyou Forest Products and merchant & groove. cannot be liable for the performance of finish DON’T staple lumber. Staples applied at the job site. Distributed by do not have enough holding power. Siding Patterns Nailing Siding (SIDE VIEW) #105 Cove T&G V2E C FJP105 1 x 6 16’ FJ Primed C FJP1344 1 x 4 16’ FJ Primed C FJP1346 1 x 6 16’ FJ Primed Plain Bevel Rabbeted Bevel #115 Double Bevel Face nail with one nail per Face nail with one nail per bearing. C FJP115 1 x 6 16’ FJ Primed bearing. Drive nail so shank Place nail about 1” above lower clears the top of the preceding edge of course. Position material Bevel FJ VG Reversible under-course by 1/8”. Beware of to allow 1/8” expansion gap at Smooth/Resawn driving the nail with too heavy of rabbet joint. an initial blow. CBPV1206 1/2 x 6 16’ CBPV3408 3/4 x 8 16’ #117 TD Bevel CBPV1208 1/2 x 8 16’ CBPV3410 3/4 x 10 16’ C FJP117 1 x 6 16’ FJ Primed #773 1” Bevel Channel Shiplap 1” Channel V & CV Shiplap C FJP773 1 x 10 16’ FJ Primed Resawn Channel Face Tongue and Groove Channel Shiplap C_FJP784R 1 x 6 16’ Blind nail 4” and 6” widths through Use one nail, 1” from the lap for 6” tongue with finish nails. Use one channel shiplap. Face nail with C_FJP785R 1 x 8 16’ nail per bearing. For wider two nails per bearing for patterns patterns, face nail with two nails 8” and wider. Space nails 1” from #771/772 1”Cove Shiplap per bearing, as in V Shiplap the edge of the overlap and 2” method. from the edge of the underlap. C FJP771 1 x 8 16’ FJ Primed Position material to allow C FJP772 1 x 10 16’ FJ Primed Trim Patterns expansion clearance of 1/8“. Boards should be nailed to horizontal blocking installed between studs at not more than 24” on center. #106 Comb Bead Primed Fascia & Trim | Western Red Cedar C FJCB106 1 x 6 16’ FJ Primed K.D. A+Btr S1S2E FJ Size OrePac Size OrePac Size OrePac Code Code Code 1 X 2 C FP102 5/4 X 3 C FP5403 2 X 2 C FP202 V Shiplap Face nail with two siding nails per #137/794 Shiplap 1 X 3 C FP103 5/4 X 4 C FP5404 2 X 4 C FP204 bearing for patterns wider than 6”. 1 X 4 C FP104 5/4 X 6 C FP5406 2 X 6 C FP206 Position nails one-quarter the C FJP137 1 x 6 16” FJ Primed width of the material from each 1 X 6 C FP106 5/4 X 8 C FP5408 2 X 8 C FP208 C FJP794 1 x 8 16’ FJ Primed edge. For narrow courses, one 1 X 8 C FP108 5/4 X 10 C FP5410 2 X 10 C FP210 nail per bearing is enough. The 1 X 10 C FP110 5/4 X 12 C FP5412 2 X 12 C FP212 nailing point should be 1” from the over lapping edge. 1 X 12 C FP112 90° FJ CM352FJ 2 x 3 C FPS203 Corner Window #433 3 Lap Rnd Edge Drop SDG Sill For further storage, painting and installation instructions please visit: C FJP433 1 x 10 16’ FJ Primed 2 X 4 C FJP1031 www.wrcla.org.
Load more

Recommended publications
  • This Code Was Put Together by Building Officials on the Peninusla As We As
    The Mudsill Connection in Retrofit Shearwalls Introduction Seismic Behavior of Level and Stepped Cripple Walls, a publication of the Consortium of Universities in Earthquake Engineering (CUREE), contains the following statement regarding damage from the Northridge Earthquake: “More than half of the $40 billion dollar property losses were due to failures of wood frame construction, primarily as a result of the damage or collapse of residential, single-family homes, multi-family apartments or condominiums.”(10) The San Francisco Bay Area is riddled with earthquake faults, some of which can rupture with an intensity far greater than that experienced at Northridge. The Association of Bay Area Governments (ABAG) expects that over 150,000 housing units in the Bay Area will be lost when just one of these, the Hayward Fault, ruptures with an expected magnitude of 7.2 or greater. Homeowners are not unaware of this fact. In response to homeowner demands to protect their homes from earthquake damage, many contracting firms in the Bay Area now specialize in residential wood frame seismic retrofit work. Through the transfer-tax retrofit rebate program the city of Berkeley actually pays 0.5% of the purchase price to every new homeowner if the money is spent on seismic retrofit work. Given that the average home in Berkeley costs close to $600,000, this can be a large amount of money. As a result of this policy, according to ABAG, Berkeley can be proud to say that over 80% of the homes in its jurisdiction have been retrofitted. Unfortunately, also according to ABAG, the majority of those retrofits will not perform as needed.
    [Show full text]
  • Copper Based Wood Preservative Systems Are Also Included
    A Comprehensive Review of CCooppppeerr--BBaasseedd WWoooodd PPrreesseerrvvaattiivveess With a focus on new micronized or dispersed copper systems By Mike H. Freeman * and Craig R. McIntyre * Abstract This paper focuses on the wood preservation aspects of copper based biocides. Included in this review are the following: Above ground and ground contact efficacy, permanence in above ground and ground contact uses, soil and water contact leaching, effects on wood properties and certain fixation aspects of copper systems. Previously unpublished data on the new micronized/dispersed copper based wood preservative systems are also included. These micronized systems now dominate the U .S. residential treated wood market which in turn accounts for roughly 50 percent of global wood preservation usage . opper is an essential micronutrient for most living Copper is needed against this challenge since very few Ccells. In larger doses though, the copper ion demon - organic molecules (other than creosote and penta ) possess strates activity as an algaecide, bactericide , fungi - activity towards soft rot fungi (Hughes 2004). cide, insecticide, and moldicide. Presently copper com - The volume of wood products treated with copper -based pounds are used for algal control, wood treatment, preservatives grew exponentially during the 1970s and antifouling pigments, and crop fungicides (Richardson 1980s and remains high today. Copper compounds also have 1997). The fungicidal properties of copper were recog - nized in the 1700 s, and copper-based preservatives have been widely and successfully used for more than a centu - This paper was received for publication in August 2008 and has ry. Although borates and organic biocides are gaining undergone the Journal’s peer review process.
    [Show full text]
  • Check out Lifeart Merchandise List
    www.LifeArtCabinetry.com www.LifeArtCabinetry.com Company Overview LifeArt Cabinetry Corp is a well-established kitchen cabinet wholesaler, owned and operated within the United States, with a manufacturing plant overseas. Our facility is headquartered in Norcross, Georgia with 100,000 square feet of distribution center and showroom, with a newly added loca- tion in Secaucus, NJ. As a cabinet wholesaler, LifeArt’s passion is to make sure it delivers the best quality kitchen cabinet solution to its dealers. With an organized logistics team, LifeArt ensures to provide only top-level ser- vice to dealers. Our Product LifeArt Cabinetry offers twelve cabinet lines in wholesale, each with its own style and color to set itself apart from the others. Whether the cabinets are used for home improvements in the kitchen, bathroom, or in an- other area of the house such as an entertainment center, custom closet, wet bars etc, they can be designed to maximize style, space, and organization. (770) 582-0098 6700 Best Friend Rd. Norcross, GA 30071 www.lifeartcabinetry.com SPECIFICATION AND PRICE SUBJECT TO CHANGE WITHOUT NOTICE • IMAGES ARE FOR REFERENCE ONLY • www.LifeartCabinetry.com www.LifeArtCabinetry.com Table of Contents Anchester_1 A1-1 - A1-14 Anchester_2 A2-1 - A2-14 Anchester_3 A3-1 - A3-14 Birmingham B1 - B14 Cambridge C1 - C15 Edinburgh E1 - E15 Heidelberg H1 - H15 Kingston K1 - K14 Oxford O1 - O15 Princeton P1 - P15 Wurzburg W1 - W14 Yorktown Y1 - Y14 lnformation Info 1- Info 31 SPECIFICATION AND PRICE SUBJECT TO CHANGE WITHOUT NOTICE • IMAGES
    [Show full text]
  • Capital-Framed-Collection-Specbook.Pdf
    FRAMED PRODUCT LINE SPECBOOK PHONE: 844-660-9889 · FAX: 770-767-3806 EMAIL: [email protected] WEBSITE: WWW.USCABINETDEPOT.COM CAPITAL COLLECTION (FRAMED CABINETS) PHONE: 844-660-9889 · FAX: 770-767-3806 · EMAIL: [email protected] · WEBSITE: WWW.USCABINETDEPOT.COM TABLE OF CONTENTS Section 1: Policies & Information About Us ..................................................................................... 2 Ordering Information ......................................................................... 3 Sample Doors ................................................................................ 4 Marketing Tools .............................................................................. 5 Terms & Conditions ........................................................................... 6 Frequently Asked Questions ................................................................. 10 Warranty .................................................................................... 12 Section 2: Styles & Pricing Highland (Prime) Series Door Styles & Specications Charleston ............................................................................ 13 Tahoe ................................................................................. 14 York ................................................................................... 15 Shaker ................................................................................ 16 Construction Specications ............................................................ 18 Cascade (Professional)
    [Show full text]
  • Tool Inventory 7.23.21
    Tool Name Category Retail Value Cost to Borrow Adjustable wrench: large Carpentry $10.46 $ 0.31 Adjustable wrench: small Carpentry $9.56 $ 0.29 Air compressor Power Tools $374.00 $ 11.22 Air ratchet wrench Power Tools $61.28 $ 1.84 Auger bit: small, drill powered Power Tools $33.50 $ 1.01 Auger: 1 person - medium duty (8 in bit included) Power Tools $587.00 $ 17.61 Auger: 2 person (8 in bit included) Power Tools $728.00 $ 21.84 Axe Earthwork $29.79 $ 0.89 Bar clamp: up to 18in Carpentry $11.48 $ 0.34 Bean bag toss (cornhole) Special Events $50.00 $ 1.50 Blower: backpack gas-powered Earthwork $299.00 $ 8.97 Blower: handheld corded (electric) Power Tools $67.65 $ 2.03 Blower: handheld cordless (electric) Power Tools $149.00 $ 4.47 Blower: handheld gas-powered Power Tools $149.00 $ 4.47 Bolt cutters Carpentry $19.97 $ 0.60 Bottle jack: hydraulic Carpentry $35.00 $ 1.05 Bow saw Earthwork $9.97 $ 0.30 Broadfork Earthwork $199.00 $ 5.97 Broom: push Custodial $16.65 $ 0.50 Broom: street sweeper Custodial $19.99 $ 0.60 Broom: sweep Custodial $8.82 $ 0.26 Buck saw Carpentry $10.97 $ 0.33 Bulb planter: long handle w/ release Earthwork $22.97 $ 0.69 Carpet Cleaner with Upholstery Cleaner Special Events $638.99 $ 19.17 Caulk gun: 10 oz Carpentry $2.98 $ 0.09 Chainsaw chaps Safety $59.98 $ 1.80 Chainsaw: gas-powered Power Tools $219.00 $ 6.57 Chair: folding Special Events $24.95 $ 0.75 Chalk line and chalk Carpentry $4.96 $ 0.15 Circular saw Power Tools $112.99 $ 3.39 Circular saw: cordless Power Tools $149.98 $ 4.50 Cultivator: long handle Earthwork
    [Show full text]
  • Abstract Racking Performance Of
    ABSTRACT RACKING PERFORMANCE OF PAPERBOARD AND WOOD BASED SHEATHING MATERIALS By Benjamin Ong A small scale (16 x 16 inch) racking tester was used to evaluate the racking performance of the paperboard and wood based sheathing materials. In this study it was shown that the staple spacing, staple size and caliper of the paperboard affect racking performance. It was established in this study that extending staples length beyond 1 inch has no advantage for the paperboard and wood based sheathing materials. Similarly, using nails for fasteners has no advantage both for paperboard and wood based sheathing materials. This finding is limited to the present set up and does not represent other racking testers. The racking performance improved when adhesive was used in combination with staples to attach the sheathing to the wood frame. It was observed after the racking test, the physical state of the paperboard sheathings indicate that staples have a higher withdrawal resistance and less tear through when compared to the nails. The stretching of the paperboards during the racking test slightly affects the tensile properties and further study is needed. The hardboard was evaluated to have better racking stiffness and strength than that of plywood and oriented strand board. The comparison of staples and nails as fasteners based on the racking stiffness and strength show that nail will be preferred for hardboard but for plywood and oriented strand board, either nails or staples could be used as fasteners. The basis weight and racking strength have an inverse relationship for the wood based sheathing. THE RACKING PERFORMANCE OF PAPERBOARD AND WOOD BASED SHEATHING MATERIALS A thesis Submitted to the Faculty of Miami University in partial fulfillment of the requirements for the degree of Masters of Science Department of Paper and Chemical Engineering by Benjamin Ong Miami University Oxford, Ohio 2006 Approved by: Advisor ______________________________ Dr.
    [Show full text]
  • Evaluation of Wood Species and Preservatives for Use in Wisconsin Highway Sign Posts
    United States Department of Agriculture Evaluation of Wood Species and Preservatives for Use in Wisconsin Highway Sign Posts Stan T. Lebow Robert J. Ross Samuel L. Zelinka Forest Forest Products General Technical Report July Service Laboratory FPL–GTR–231 2014 In cooperation with the Wisconsin Department of Transportation. Abstract hardwoods. Copper naphthenate is non-corrosive to alu- minum and would avoid warp associated with re-drying The Wisconsin Department of Transportation (WisDOT) after treatment with water-based preservatives. WisDOT uses wooden posts to support many types of signs along may want to consider purchasing a small volume of copper state highways. WisDOT currently uses red pine or Southern naphthenate-treated posts to evaluate the handling character- Pine posts treated with chromated copper arsenate (CCA) istics of this oil-based preservative. and has generally experienced satisfactory performance and service life. However, there are some areas of concern, as Keywords: wood preservatives, wood species, sign posts, well as potential opportunities for diversifying the wood highway, Wisconsin species and preservatives used. Warp is sometimes a prob- lem with the current pine posts, and increased use of locally Acknowledgment sourced wood species for the sign posts could decrease The authors acknowledge the valuable input received from transportation costs and potentially benefit Wisconsin in- Matt Rauch of WisDOT in refining the study problem areas, dustries. Although CCA is a highly effective preservative, it relating field experiences, and describing WisDOT practices may not be the optimum treatment for alternative wood spe- and procedures. cies. This study reviewed the characteristics of alternative wood species and wood preservatives and evaluated their potential for use in Wisconsin highway sign posts.
    [Show full text]
  • Assembling Frames
    rames are the workhorses of the man- This, then, makes frames “deep” (when the 1) First, frames are under a lot of pres- made parts of a honey bee hive. They tall end bars are used), “medium” or “Illi- sure in the hive. They are suspended by their Fprovide the structure in which bees nois” (when the medium end bars are used), lugs which rest on a special groove present build the combs; thus, frames bear the en- or “shallow” (when the short end bars are on the front and back internal walls of the tire weight of a colony’s wax infrastructure, used). End bars have notches at the top and super in which the frames are placed. The honey/pollen stores, and brood nursery. bottom that are cut to accommodate the top weight of a deep frame full of honey can ex- They are spaced from one another and the and bottom-bars respectively. Most end bars ceed 10 pounds. This, coupled with the fact hive’s walls a distance of 3/8s of an inch. contain two-to-four holes that are used when that frame lugs are glued into the hive boxes This spacing, termed “bee space,” limits wiring foundation into frames. by the bees using propolis, means that great bees’ placement of propolis or wax in the The bottom bars of a frame come in three force must be used to free the frame from area between adjacent frames and between types: (1) solid, (2) split, and (3) grooved the hive when removing them for inspection frames and the hive’s walls.
    [Show full text]
  • SOLITEX EXTASANA® Application & Fixing Guide – Timber Frame
    SOLITEX EXTASANA® Application & Fixing Guide – Timber Frame Weather Resistive Barrier for EQUITONE Fully Ventilated Façade System SOLITEX EXTASANA® - Timber Frame Application & Fixing Guide - EQUITONE 1 SYSTEM Weather Resistive Barrier Wall IMPORTANT DUPLEX double sided tape is not intended to provide long term fixing but is an installation aid to hold the membrane in place until the façade mounting system is in place. Membrane should be 1 2 pulled taut to ensure TESCON® EXTORA tape can Preparing Timber Framing Initial Fixing Point be easily installed and adequate pressure applied Ensure all studs are aligned and free from splinters. Apply 5-6 staples in the top corner before unrolling using the PRESSFIX tool. Plane or sand where necessary. the membrane over the studs. Pull taut and fix opposite top corner with 5-6 staples. 3 4 Pull taut and fix Fix top edge SOLITEX EXTASANA® Triangulate and Fasten Fix the membrane at each stud along the top edge Pull the membrane down and taut at the centre and ensuring the staples are within 150 mm from the fix with 2-3 staples at the bottom edge. edge. Pull taut and fix 5 Pull taut and fix 6 Fix Bottom Corners Successive Layers of SOLITEX EXTASANA® Pull taut and fix each bottom corner with 2-3 Apply successive layers of SOLITEX EXTASANA® using staples. the upside-down sequence compared to the bottom layer. …and the insulation is perfect! 2 SOLITEX EXTASANA® - Timber Frame Application & Fixing Guide - EQUITONE SYSTEM Weather Resistive Barrier Wall 150 mm 7 8 Overlapping SOLITEX EXTASANA® Fixing SOLITEX EXTASANA® Around Windows The membrane shall be overlapped 150 mm.
    [Show full text]
  • 71180341 REV0.1 STAPLE SALES BROCH ENHAN DSGN FIX.Qxp
    Advanced Design Fixation Staples Made for strong attachments Advanced concepts in staple design Table Fixation Staples offer a variety of Osteotomy Fixation Staples can be used in applications including knee ligament repair, high tibial osteotomies to correct varus or valgus arthrodesis of the wrist and ankle, epiphyseal deformities, helping to retain cut surfaces in the growth arrest, ankle fracture, transplantation of the desired degree of apposition until healing occurs. tibial tubercle, avulsion of the Achilles tendon, triple Equal leg lengths help prevent malposition arthrodesis, and proximal humerus fractures. during insertion. Smith & Nephew offers a complete family of fixation Underside spikes “tack down” rather than press staples with distinct design advantages. down, allowing better fixation of soft tissue and reducing the chances of necrosis. Tapered legs wedge into bone. Serrations that project from the legs (rather than The driving mechanism locks onto each staple to being cut into them) lock into hard bone and help prevent slippage. decrease chances of staple back-out. Cobalt chromium alloy (ASTM F-75). Regular Fixation Staples are especially useful in Krackow HTO Staples are very useful in high fixing soft tissue to bone including anterior tibial osteotomies and other applications where cruciate reconstruction. They are also useful for the combined benefits and improved rotational fragment fixation, tendon and ligament repair, and stability of a blade/staple are indicated. in controlling bone growth. Four sizes are Serrations in the inner blade help resist pullout. available, in regular or short lengths, with or without spikes. Look to Smith & Nephew for all your stapling needs. For more information, contact your Smith & Nephew Representative, or call 1-800-238-7538.
    [Show full text]
  • Fplgtr113.Pdf
    Abstract Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses. Keywords: wood structure, physical properties (wood), mechanical properties (wood), lumber, wood-based composites, plywood, panel products, design, fastenings, wood moisture, drying, gluing, fire resistance, finishing, decay, sandwich construction, preservation, and wood- based products On the cover: (Left to right, top to bottom) 1. Research at the Forest Products Laboratory, Madison, Wisconsin, contributes to maximizing benefits of the Nation’s timber resource. 2. Testing the behavior of wood in fire helps enhance fire safety. 3. The all-wood, 162-m (530-ft ) clear-span Tacoma Dome exemplifies the structural and esthetic potential of wood construction (photo courtesy of Western Wood Structures, Inc., Tualatin, Oregon). 4. Bending tests are commonly used to determine the engineering properties of wood. 5. Engineered wood trusses exemplify research that has led to more efficient use of wood. 6. The Teal River stress-laminated deck bridge is March 1999 located in Sawyer County, Wisconsin. 7. Kiln drying of wood is an important procedure Forest Products Laboratory. 1999. Wood handbook—Wood as an during lumber manufacturing. engineering material. Gen. Tech. Rep. FPL–GTR–113. Madison, WI: 8. Legging adhesive (photo courtesy of Air Products U.S. Department of Agriculture, Forest Service, Forest Products and Chemicals, Inc., Allentown Pennsylvania). Laboratory. 463 p. Adhesive bonding is a critical component in the A limited number of free copies of this publication are available to the performance of many wood products.
    [Show full text]
  • 21° Framing Nailer
    FRAMING NAILERS /C OIL NAILERS NPR90 21° F RAMING NAILER Tool Nail Capacity Nail Range Diameter Firing Mode NPR90 50 - 75 Nails 2” to 3-1/2” .113 - .148 Restrictive 50mm to 90mm Applications: Crating, Decking, Fencing, Framing, Pallet Manufacturing, Pallet Repair, Sheathing, Wall Paneling Construction Features: Uses Spotnails ® 20-22 ° Nails, Bump Fire Plunger Included, Belt Hook Available (P-97469), Flush Drive Attachment Available (AS-99076), Rubber Grip for Comfort, Safety Glasses Weight: 8 lbs. 6 oz. Dimensions: 21” L x 4” W x 13-3/4” H NTD90 31° C LIPPED HEAD FRAMING NAILER Tool Nail Capacity Nail Range Diameter Firing Mode NTD90 89 Nails 2” to 3-1/2” .113 - .148 Restrictive 50mm to 90mm Applications: Crating, Decking, Fencing, Framing, Pallet Manufacturing, Pallet Repair, Sheathing, Wall Paneling Construction Features: Uses Spotnails ® 31 ° Paper Tape Strip Nails, Bump Fire Plunger Included, Belt Hook Available (P-97469), Flush Drive Attachment Available (AS-99076), Rubber Grip for Comfort, Safety Weight: 8 lbs. 6 oz. Glasses Dimensions: 16-1/2” L x 4-1/2” W x 14-1/2” H QCND65 0° P LASTIC COLLATED NAILER Tool Nail Capacity Nail Range Diameter Firing Mode QCND65 300 Nails 1-1/4” to 2-1/2” .083 - .099 Selectable 32mm to 64mm Applications: Decking, Exterior Trim, Fencing, Pallet Manufacturing, Pallet Repair, Sheathing, Siding Features: Uses Spotnails ® CPD 0 ° Plastic Insertion Nails (Duo-Fast Type), 360 ° Adjustable Exhaust, Adjustable Depth Control, Easy Maneuverability, Nail Basket, Rubber Grip for Comfort, Safety Glasses Weight: 5 lbs. 2 oz. Dimensions: 12” L x 5-3/4” W x 13” H UCNM65 15° P LASTIC OR WIRE COLLATED NAILER Tool Nail Capacity Nail Range Diameter Firing Mode UCNM65 300 Nails 1-1/4” to 2-1/2” .083 - .099 Selectable 32mm to 64mm Applications: Decking, Exterior Trim, Fencing, Pallet Manufacturing, Pallet Repair, Sheathing, Siding Features: Uses Spotnails ® 15 ° Plastic Insertion or Wire Weld Coil Nails, 360 ° Adjustable Exhaust, Adjustable Depth Control, Easy Maneuverability, Nail Basket, Rubber Grip for Comfort, Safety Glasses Weight: 4 lbs.
    [Show full text]