Test Products for Power Systems from Megger

Test products for power systems from Megger. WWW.MEGGER.COM

The word ‘Megger’ is a registered trademark For more than 100 years the Megger name has Contents been synonymous with high quality instruments for the testing and measurement for electrical Page power applications. Insulation resistance testing 2-3 The trademark was ﬁrst registered in May 1903 Insulation testing 4 and is jealously guarded by the company. High voltage test equipment 5 Protection testing 6 Automatic protective relay testing 7 Cable fault location equipment 8-9 Transformer testing 10-12 Transformer insulating oil testing 12 Watthour meter testing 13 Switches and test blocks 13 Battery testing 14-15 Earth resistance testing 16-17 Low resistance measurement 18-19 Power quality 20-21

Megger offer you a complete service

Although we’re best known for our world famous With a constant ﬂow of new products to assist the electrical engineer in range of insulation testers, Megger provides a full making the right measurements and exciting new software packages to help service solution to meet your electrical test and monitor, analyse and report, Megger can also offer training to understand measurement needs. and operate the instruments safely and effectively.

Our products provide testing solutions in the Our training operation can be accessed globally using the web. Megger can most critical maintenance areas including cable also offer training at your premises or at its centres in Dover, Dallas and Paris. fault locating, protective relay testing, and power quality testing, as well as being the supplier of For more information visit: www.avotraining.com choice for hand-held electrical test and measurement instruments for electrical installation, data and telecom engineers. With such a diverse product offering, we are the NEW single source for electrical test and measuring instruments. Megger PowerDB™ In our 100 years Megger has built up a wealth of expertise in our specialist fields. You can benefit Power test data analysis and certification software FREE from our expertise. Designed to manage the complete suite of test data collected from power system assets. Test forms are designed for the Megger has recently revised its publication majority of the electrical apparatus on the market today. PowerDB currently supports the following devices: “a guide to diagnostic insulation testing over Batteries Generators Loadbreak Switches Switchboards 1kV” as well as producing a selection of other Cables Ground Fault Tests Motor Control Centers Transducers useful applications guides. These include “the Circuit Breakers Ground Mat/Grid Tests Power Factor Tests Transfer Switches battery testing guide”, “fault finding solutions” Coordination Data Instrument Transformers Power Transformers Watthour Meters and “a guide to low resistance measurement”. Disconnects Insulation Fluids Relays For your copy of any of these guides return the The software will perform extensive information processing including equation calculations, temperature correction factors card you will find on the inside back cover of and charting. Data trending for predictive failure analysis is accomplished by charting historical results, stored in PowerDB or this catalogue. imported from other party’s proprietary database software, for any piece of equipment.

Contents 1 Insulation resistance testing Megger MIT520 NEW 5kV insulation resistance tester Insulation resistance testing The MIT520 offers the ability to test insulation to 5kV. Model BM15 MJ15 MIT510 MIT520 MIT1020 S1-5010 Display Graphical ✓ It allows automatic IR, PI, DAR, SV and DD tests, and Analogue ✓✓ Analogue/Digital ✓✓✓✓ results storage and download give full diagnostic Power supply Mains power ✓✓✓✓ information. Rechargeable optional optional ✓✓✓✓ Hand-crank ✓ The MIT520 can be powered using both mains or its Dry cell ✓✓ Test voltage 10.0kV ✓ on-board rechargeable battery. 5.0kV ✓✓✓ ✓✓✓ 2.5kV ✓✓✓ ✓✓✓ 1.0kV ✓✓✓ ✓✓✓ 500V ✓✓✓ ✓✓✓ 250V ✓✓✓ 25V steps 50V to 5kV ✓ 10V steps 50V to 1kV ✓✓ 25V steps 1kV to Max test voltage ✓✓ Measurements Max reading 20GΩ 20GΩ 15TΩ 15TΩ 35TΩ 5TΩ Min reading 100kΩ 100kΩ 10kΩ 10kΩ 10kΩ 10kΩ Voltage ✓✓✓ ✓✓✓ Time constant ✓✓✓ Capacitance ✓✓✓✓ MIT520 Leakage current ✓✓✓✓ Test types Polarisation index ✓✓✓ Dielectric absorption ratio ✓✓ Step voltage ✓✓✓ Dielectric discharge ✓✓✓ Other features Timer control ✓✓✓ Timer display ✓✓✓✓ 5mA test currents ✓ Megger MIT1020 NEW 3mA test currents ✓✓✓ 2mA test currents ✓ 1mA test currents ✓✓ 10kV insulation resistance tester Guard terminal ✓✓ ✓✓✓✓ USB output ✓✓ The MIT1020 offers the ability to test insulation to 10kV, to RS232 output ✓✓✓ RS232 control ✓ comply with IEEE43: 2000. It allows automatic IR, PI, DAR, Calibration Certiﬁcate ✓✓✓ SV and DD tests, and results storage and download give full diagnostic information. Megger BM15 and The MIT1020 can be powered using both mains or its on-board rechargeable battery. Megger MJ15 MIT1020 Analogue dual supply

Easy-to-use 5kV insulation testers in a tough ﬁeld case. The MJ15 offers a unique combination of battery and hand cranked generator to give the answer to “go / no go” testing. MJ15

Megger Series 1-5010 Megger MIT510 NEW Diagnostic insulation tester 5kV insulation resistance tester S1-5010 The Series1-5010 is a heavy-duty mains/battery powered The MIT510 is an easy to operate insulation resistance tester instrument. Offering auto test and results storage, it is a that is very tough. It allows automatic IR. The built-in timer stand-alone instrument for maximum diagnostic and high test ranges allow simple and quick evaluation of information and predictive maintenance. the condition of the insulation under test. The MIT510 is mains or battery powered.

MIT510

2 Insulation resistance testing Insulation resistance testing 3 Insulation testing High voltage test equipment

Capacitance and dissipation factor or tanδ testing High voltage test equipment Model d.c. output a.c. output d.c. test sets Continuous Short circuit Continuous Short circuit 220005 5kV 5mA 5mA Insulation testing 220015 15kV 2mA 5mA Model Delta 2000 CB100 670025 670065 670070 220070 70kV 3.5mA 5mA Output voltage 12kV 28V 2.5kV 12kV 12kV 220123 120kV 2.5mA 5mA Capacitance measuring range in µF 0-0.11 or 0-1.2 0-0.22 0-0.22 0-0.22 or 220164 160kV 2mA 5mA 0-1 with inductor 0-1 with inductor a.c. test sets Dissipation factor 0-90% 0-30% 0-200% 0-200% 0-200% 230315 3kV 12mA UST test ✓✓✓✓✓ 230415 4kV 12mA GST test ✓✓✓✓✓ 230425 5kV – 17mA 4kV 3mA 12.6mA GST guarded test ✓✓✓✓✓ 686100 Non-resonant 50/100kV 80/150mA Watts loss measurement ✓✓✓✓✓ 681100 Resonant 50/100kV 80/150mA Current measurement ✓ ✓✓✓ 686100 Non-resonant 50/100kV 40/75mA Range extension ✓✓ ✓ 681100 Resonant 50/100kV 40/75mA Interference suppression Automatic Inherent Manual Manual Manual Balancing Automatic Manual Manual Manual Manual Data storage ✓ Bar code reader ✓ PC software ✓ 681100 series RS232 printer output ✓ 50/100kV a.c. dielectric test sets Delta 2000 681100 series a.c. dielectric test sets are a.c. high-voltage sources for testing electrical insulation. The standard system 12kV fully automated capacitance and tanδ includes a control/instrument cabinet, a high-voltage test bridge transformer assembly and all necessary cables including ground and input power. The ultimate instrument for dissipation factor testing, the DELTA2000 offers automatic measurement of dissipation factor, capacitance, watts loss and leakage current. It is 681100 series ideal for the assessment of insulation in high voltage apparatus such as transformers, bushings, circuit breakers, Delta 2000 cables, surge arresters and rotating machinery. 220000 series

70kV, 120kV & 160kV d.c. dielectric test set CB100 220000 series provides a dependable, safe, lightweight and portable d.c. voltage source for testing the quality and Low voltage capacitance and tanδ test bridge integrity of electrical power cables, cable installations,

Lightweight and low-cost the CB100 is ideal for workshop motors, switchgear, insulators, transformers and capacitors. use. Manually balanced it offers direct readout of tanδ and capacitance, overcoming interference by using a test frequency of 80 or 100Hz. CB100

670000 series

2.5 and 12kV semi-automatic capacitance and tanδ test bridge

These instruments feature automatic balancing of dissipation factor and manual balancing of capacitance and interference suppression, allowing use in energised HV substations. There is direct readout of tanδ, capacitance and 200070 series watts dissipated. 670000 series

4 Insulation testing High voltage test equipment 5 Protection testing Automatic protective relay testing

Protection testing Protective relay test system Model CB832 PCITS2000/2 CB845 MS2 DDA1600 DDA3000 DDA6000 SCITS100 SITS120 SR90 SR98 Output current In Amps 0 - 1800 0 - 2000 0 - 5000 0 - 240 0 - 19200 0 - 35000 0 - 50000 0 - 100 0 - 120 0 - 140 0 -115 The MPRT tester and AVTS® software from Megger raises Number of ranges 3 2 4 3454 the standard for the automatic testing and management Voltage output V a.c. 0 - 250 0 - 120 0 - 240 0 - 600 0 - 300 V d.c. 0 - 240 0 - 240 0 - 500 0 - 240 of protective relay systems. The MPRT offers traditional Power In VA 1750 7200 2400 700 1400 920 manual and semi automatic testing of the relay system Time Period in S 0 - 999.99 0 - 600 0 - 999.99 0 - 999.99 0 - 99999 0 - 99999 0 - 99999 0 - 599.99 0 - 999.99 0 - 9999.99 0 - 9999.99 whilst the AVTS package offers fully automatic testing as Resolution in S 0.001 0.01 0.001 0.001 0.0001 0.0001 0.0001 0.01 0.001 0.0001 0.0001 Cycles 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999.9 0 - 99999.9 well as relay maintenance schedule management.

Megger MPRT Primary current injection testing (PCITS) and circuit breaker testing (CBT) MPRT8430 protective relay Protective relay tester test set PCITS2000/2 The power unit offers a range of new features including Primary current injection test set constant and high power output capability through the These tough self-contained test sets are designed for entire power curve, the combination of voltage and current operation by one person and are comparatively light. With a generators into one amplifier package giving the flexibility separate hand-held controller connected by an expandable of 4 current and 4 voltage outputs or 8 current outputs for cable it allows the operator to work close to a protective testing multi-phase differential relays, and built-in relay while controlling a test. transducer testing capability. The test set also offers 4 communication ports including facilities for high speed DDA1600, DDA3000 and DDA6000 downloads and upgrades via the internet. High current injection test sets The touch-view interface makes it easier to perform DDAs are a range of high current units capable of PCITS2000/2 manual and semi-automatic relay testing. The large colour generating a test current of up to 50000A through a circuit LCD touch screen allows the operator to test virtually all AVTS test screens breaker. The instrumentation and control system enable the types of relays without the need for an external computer. operator to vary the pulse time and firing angle of the Menu screens and function buttons provide a quick and injected signal. They can be used for testing protection relays easy method to drive the selected test. and low voltage circuit breakers at the commissioning stage.

CB832 and CB845 DDA1600 Megger AVTS Current injection sets Advanced visual test software Capable of generating up to 1800A and 5000A respectively for an instantaneous trip test, these units are ideal for A version of AVTS can be supplied to meet individual commissioning applications requiring high current injection. customer’s requirements. AVTS Basic is supplied with all The CB current injection sets offer adequate driving voltage MPRT systems but can be upgraded to AVTS Advanced or for all but the highest circuit impedance. the full AVTS Professional packages. AVTS Basic allows full Automatic protective relay testing automatic operation of the test set with pre-prepared test Relay type IEEE no. SCITS100/2 SITS120 SR98 MPRT files, whilst the Advanced and Professional options give Time delay 2 ✓✓✓✓ increased functionality for the preparation of automatic test Impedance 21 ✓✓ ✓ Secondary current injection testing files and relay performance evaluation. Volts per hertz 24 Synchronising 25 ✓✓ ✓✓ Automated relay testing enables the test engineer to save a Directional power 32 SCITS100 and SITS120 Loss of excitation 40 ✓✓ great deal of time and money by rapidly executing the test Negative sequence Current and voltage injection sets process and minimising any protected power system over-current 46 ✓✓ Tough test sets suitable for general purpose relay testing. Negative sequence equipment down time. under-voltage 47 ✓ A wide range of relays can be tested due to their operating Instantaneous system flexibility. Current and voltage on the output SR98 AVTS packages have a powerful graphical interface that is over-current 50 ✓✓✓✓ terminals are measured and displayed. An accurate timer developed and continuously upgraded by Megger to Over-current 51 ✓✓✓✓ Moulded case breaker 52 ✓✓✓ measures the relay operating time. The SITS120 offers a simplify fully automatic and complex relay testing. It is SR90 and SR98 Over-voltage 59 ✓✓✓ lighter option. designed to meet the existing and future needs of ✓✓ Voltage and current injection sets Directional over-current 67 protection technicians and engineers worldwide helping to Reclosing 79 ✓✓ The SR90 calibrates, performs acceptance testing and Frequency 81 ✓ MS2 improve efficiency and reduce testing errors. ✓ ✓ troubleshoots the most popular solid-state and electro- Differential 87 ** Circuit breaker and overload relay test set Tripping 94 ✓✓ mechanical relays. Tests all moulded case circuit breakers, Auto synchronising 25A ✓ The MS2 is capable of delivering 750A instantaneously. It is motor overload relays and timing circuit breakers. Manually K500 Voltage controlled ideal for over-current and earth fault relays and moulded operated units work separately when testing simple relays over-current 27 / 51 ✓✓✓✓ or interconnected to provide four simultaneous outputs Under / over voltage 27 / 59 ✓✓✓ case circuit breakers. Protective relay tool kit d.c. under / over current 37 / 76 ✓✓ for more complex relays. The SR98 offers a lightweight, ✓✓✓✓ A comprehensive range of relay tools containing over 40 Motor overload 51 / 86 field portable test set capable of testing a wide range of Ground directional electro-mechanical solid-state and microprocessor-based specific items. The whole kit is supplied in either a over-current 67N ✓✓ protective relays. lightweight soft case or a tough lockable vinyl case. **Two units required

6 Protection testing Automatic protective relay testing 7

AVTS is a registered trademark of Megger Group Limited and/or its subsidiaries. Cable fault location equipment Megger TDR1000/2 Single channel cable fault locator A state of the art TDR capable of identifying and locating DART faults on metallic cables. The TDR1000 is suitable for use Cable fault analysis system on both dead or live cables without a blocking filter, up to CATIII 300 V phase-to-earth. The DART® cable fault analysis system is a microprocessor controlled TDR designed to identify and locate faults in power cables, using standard pulse echo, arc reflection, differential arc reflection and impulse current methods of prelocation. The unit being menu driven is easy to use, and allows operators to quickly identify and locate faults accurately Megger TDR2000/2P TDR1000/2 and effectively. DART Dual channel cable fault locator A state of the art mono or colour display two-channel TDR. PFL1000, PFL4000 and PFL5000 capable of identifying and locating faults on metallic cables. The TDR2000P is suitable for use on dead or live cables Power fault locator systems without a blocking filter, up to CATIII 300 V phase-to-earth with a range of up to 20 km. The TDR has an internal A series of cost-effective mobile systems dedicated to memory and the TraceMaster software supplied allows identifying, and finding faults in copper cables, accurately, storage and analysis of waveforms on a PC. and efficiently. Each model combines a d.c. test facility, proof/burn mode, surge pulse (impulse current), arc reflection, and pulse echo in a compact field portable module (dependent on model ordered).

Outputs Surge impulse Model d.c. Burn Surge Energy L1050, L1070, L1071 Accutrace, PFL1000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µF TDR2000/2P PFL4000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µF and Cable Route Tracer PFL5000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µF Portable cable locators These instruments are used to locate the exact route and depth of metallic cables. The instruments capabilities are Surge impulse generators PFL4000 enhanced by offering both passive and active modes. For Surge generators are used to generate a flashover at the point of fault that can be detected ease of use, and improved efficiency, the instruments can by an acoustic receiver; this is the preferred method to pinpoint faults in power copper cables. be either inductive or conductively coupled. ■ Megger has a series of surge generators suitable for various cable rating. Multiple output frequencies* ■ Variable tx output power level* Surge impulse generators ■ Peak & null detection* Surge impulse H.V. output ■ Push button depth measurement* Model Output Energy d.c. test Burn ■ (* dependent on model) 651404 Suitcase 0 - 15kV 300 joules, 2.5µF - - 651017 Portable 0 - 15kV 536 joules, 5µF 0 - 25kV 0 - 30mA 651016 Dual-voltage 0 - 7.5kV 450 joules, 4µF 0 - 25kV 0 - 30mA 0 - 15kV 450 joules, 16µF 0 - 25kV 0 - 30mA 651028 Standard 0 - 25kV 1250 joules, 4µF 0 - 30kV 0 - 50mA L1070 653031 Heavy Duty 0 - 25kV 3750 joules, 12µF 0 - 65kV 0 - 100mA 0 - 30kV 5400 joules, 12µF 0 - 65kV 0 - 100mA 653031-32 Heavy Duty 0 - 25kV 7500 joules, 24µF 0 - 65kV 0 - 100mA 0 - 30kV 10800 joules, 24µF 0 - 65kV 0 - 100mA DETEX® Voltage detectors and phasing testers SD3000/2 The DETEX range of testers is ideal for determining the Acoustic/Electromagnetic surge detector presence of voltage be it phase to earth or phase to phase. A verification unit is available to ensure safe operation. The SD3000 is a dual standard acoustic/electromagnetic receiver used to pinpoint Voltage detectors are suitable for voltages from 2.3kV to the location of flashovers, generated at the point of fault by a surge generator. 550kV. Models available with electronic LED and audible By incorporating a second detector (Model SD3002) the direction and distance to indication or neon indication. the fault is displayed. Phasing testers are available from 2.4kV to 69kV with a choice of analogue or neon voltage indication. Earth fault locators BGFT and BGL DETEX See page 15

SD3000

8 Cable fault location equipment Cable fault location equipment 9

DART is a registered trademark of Megger Group Limited and/or its subsidiaries. DETEX is a registered trademark of Société Anonyme des Etablissements CATU. Transformer testing TTR550005 Single-phase transformer turns ratio test set Windings The single-phase TTR measures power and distribution transformers using the manual balancing method. A hand Transformer testing crank provides the power for the TTR550005. Model TTR550503 TTR100 TTR25 TTR550005 Turns ratio range 0.8 to 45,000 0.8 to 20,000 0.8 to 20,000 0.001 to 129.999 Excitation voltage 8V, 40V and 80V 8V 8V 8V Excitation current range 0 to 500mA 0 to 100mA 0 to 100mA 0 to 1A Operation Automatic Automatic Automatic Manual Transformer ohmmeter Power source Mains Rechargeable batteries Batteries Hand-cranked Weight 7.5kg 1.5kg 1.5kg 7.3kg Transformer winding resistance and tap-change test set Field portable low resistance measuring instrument designed to test transformer windings, motors, TTR550503 TTR550005 generators and tap changers. The two independent Three-phase transformer turns ratio test set measuring channels greatly reduce the test duration of large inductive loads like transmission transformers, Measures three phases simultaneously, the turns ratio of where it is possible to measure secondary and primary power, instrument and distribution transformers. With a windings simultaneously. turns ratio range up to 45,000:1 and a 0.1% accuracy only weighing 7.5kg, the TTR is ideal for testing complex three- phase substation power transformers quickly and accurately, minimizing the possibility of errors. The performance of the TTR has been further enhanced by improved software Megger MCTT10 NEW allowing improved reporting and remote control from a Current transformer tester PC or laptop. The MCTT10 test set is a portable unit for performing Transformer ohmmeter saturation and ratio tests on current transformers using TTR550503 the voltage-comparison method. It provides a variable voltage output and precision instrumentation for testing Megger TTR100 single and multi-ratio CTs. All tests, saturation and ratio – can be performed without changing any leads. Current Hand-held transformer tester transformers can be tested in their equipment Fully three-phase capable, the TTR100 is the low cost conﬁguration, such as being mounted in transformers, solution for three-phase transformer testing. The lightest oil circuit breakers or switchgear. It is, however necessary and most portable TTR test set available, it offers a full set for the equipment to be totally isolated from the electrical of tests including; transformer turns ratio, excitation system prior to testing. current, phase angle deviation, winding resistance and transformer polarity the results of which can be stored on board for later downloading. Polarity tester MCTT10 Transformer polarity veriﬁer

TTR100 This simple device can help avoid an expensive mistake. Megger TTR25 NEW Its small size and reliable construction make it a useful Hand-held TTR addition to any tool box. The Megger TTR25 is an automatic hand-held transformer ratio test set used to measure the turns ratio, excitation current and polarity of windings distribution and power Phase sequence and continuity transformers, potential and current transformers, and tapped transformers. indicator Providing positive indication of phase sequence on energized lines and which phase, if any, is faulty. COMLink

Communications interface software TTR25 Motor and phase rotation tester The COMLink program provides a communications interface A compact, rugged and portable instrument suitable for for transferring data from three phase TTRs and hand-held phase sequence and motor ratio testing. Suitable for TTR100s, as well as BITEs, and DARTs to a PC. It allows determining the rotation direction of 1, 2 or 3-phase remote control operation of Three Phase TTRs, and for all motors, rotation or sequence of energized power circuits. instruments the viewing of test data, creation of test data Can also be used to determine the polarity of instruments databases and printing out of test reports. and power transformers, and phase/polarity of unmarked Motor and phase rotation motor windings. tester

10 Transformer testing Transformer testing 11 Transformer insulating oil testing Watthour meter testing Moisture in oil testing PHAZER® ■ Megger KF875 Watthour meter test system Portable moisture in insulating oil test set Easy to use, portable one button test set with integral The PHAZER family of watthour meter test sets are true printer. Can be powered from mains, internal three-phase, fully automatic systems capable of testing rechargeable battery or car battery. It is ideal for on site use. virtually all types of ANSI socket- mounted and bottom- connected single- and three-phase (three and four wire) Megger KF-UNI electricity meters. Portable variable specific gravity moisture in The PHAZER family consists of specific models for testing oil test set socket-mounted meters and specific models for testing Easy to use test set that titrates for specific gravities between 0.60 and 1.40. It is portable with integral printer. panel-mounted and bottom-connected meters. Offering Can be powered from mains, internal rechargeable battery KF875 state of the art optical sensing and a built-in automatic or car battery. It is ideal for on site use. calibration routine. Megger KF-LAB NEW Variable specific gravity moisture in oil test set Easy to use test set that titrates for specific gravities between 0.60 and 1.40. Designed specifically for laboratory use the KF-LAB is mains powered only. MA10

Dielectric strength testing Portable watthour meter standards PHAZER Megger OTSAF/2 KF-LAB The MA10 watthour standards are totally autoranging on Auto testing series the potential input, current input and auxiliary power input. A series of fully featured laboratory instruments which have The three summing current inputs can be used to perform world-wide test speciﬁcations pre-programmed for ease of closed link testing. Models with VARhour and Qhour use. A custom test facility enables the operator to vary the capabilities are available for testing multi-function solid parameters of the tests. Variants offer maximum test voltages of 60kV, 80kV and 100kV. state meters. Megger VCM100 Calibration meter Veriﬁes the calibration of all AF/2 laboratory models of oil test sets. OTSAF/2 Switches and test blocks Megger OTS60PB Portable automatic testing STATES® switches The smallest lightest fully automatic portable oil test set available with test voltage up to 60kV. Internal rechargeable Test switches battery for operation in remote locations. Optional printer and fully programmed international test sequences. Covers the complete area of panel connections from Megger OTS60SX terminal block to knife switches. All products give long term connection quality and mechanical stability. Manual testing Lightweight semi-automatic 60kV oil dielectric strength test set which is simple to use and can be powered from a range of mains supplies. OTS60PB

Transformer insulating oil dielectric strength testing STATES switches Model OTS100AF/2 OTS80AF/2 OTS60AF/2 OTS60PB OTS60SX Test voltage 100kV 80kV 60 kV 60kV 60kV Function Automatic Automatic Automatic Automatic Semi-automatic Power supply Mains Mains Mains Rechargeable battery mains Weight 40kg 40kg 40 kg 19kg 17.5kg ■ For sale outside the EU only

12 Transformer testing Watthour meter testing 13

PHAZER and STATES are registered trademarks of Megger Group Limited and/or its subsidiaries. Battery testing BITE2P Impedance tester for up to 7000Ah cells Routine impedance testing of batteries is fast and rigorous and insures against the cost of power breakdown. A rugged durable instrument whose enhanced capabilities make it easier to determine the true state of health of a Battery testing battery system, terminal plate to terminal plate. Model BITE3 BITE2P For batteries of capacity 2000Ah 7000 Ah The BITE2P is ideal battery systems up to 7000Ah, used in d.c. voltage range 0 - 30V 0 - 25V d.c. voltage resolution 1mV 1mV substations, generating stations, telephone exchange UPS Impedance range 0 - 100mΩ 0 - 100mΩ Impedance resolution 1µΩ 1µΩ systems and cabinetised UPS batteries, railway substations, Weight 2.6kg 14.5kg signal and communications installations. BITE2P Megger BITE® 3 NEW

Battery impedance test equipment The Megger BITE3 battery impedance test equipment BGFT determines the health of lead-acid cells up to 2000Ah by taking measurements of the most important battery Battery ground fault tracer parameters, cell impedance, an internal ohmic test, cell Manually balanced instrument that identifies, tracks and voltage, intercell connection resistance and ripple current. locates ground faults in unearthed d.c. battery systems For the first time in a battery test instrument, the BITE3 on-line. Effective in high electrical noise environments, as measures float current and the harmonic content of the the strength of test current can be adjusted. Useful for ripple current. There is even a built-in spectrum analyser industries where power supply for operating measurement, to show the harmonic content of the ripple current. It has communication and control equipment is critical. firmware that can be upgraded through the Internet and supports multiple languages. BITE3 BGFT

BGL ■ PROACTIV NEW Battery earth fault trace This instrument detects, tracks and locates earth faults Battery database management software on battery or ﬂoating systems by injecting a 21 or 25Hz ProActiv is a powerful yet easy-to-use battery database signal (depending on line frequency) between the system management software designed to aid the analysis and and earth. The resulting current is then traced through monitoring of each individual battery in a battery system. the system with a clamp accessory, knowing that the Failure of a battery system within environments such as fault current will ﬂow to earth until the fault is located. utilities, hospitals or manufacturing plants can result in Designed for operation on live battery systems, hence operational failure of the devices connected to it. there is no requirement to isolate the system.

ProActiv assists the user to avoid battery failures, budget for BGL PROACTIV test screens future battery string and cell replacements, and plan battery change-outs in an orderly manner. It utilizes a standard Microsoft® Access® database format allowing the user to organize and manage battery data such as voltages, impedance, intercell connection resistance, ripple current, speciﬁc gravity, and IR thermographs.

■ For sale outside the EU only

14 Battery testing Battery testing 15

BITE is a registered trademark of Megger Group Limited and/or its subsidiaries. Microsoft and Access are registered trademarks of the Microsoft Corporation and/or its subsidiaries. Earth resistance testing Megger DET3TD and DET3TA NEW

Earth resistance testing Three and two terminal earth tester Model DET2/2 DET3/2 DET5/4D DET5/4R DET4TD DET3TC DET3TD DET3TA Maximum earth resistance ranges 2 kΩ ✓✓✓✓ Ideal for small earthing systems, earth rods and lightning 20 kΩ ✓✓ ✓ ✓ conductors the DET3T gives you the choice of digital or Resolution 0.001 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 2.5% of analogue displays, offering simple one button operation scale length with auto-ranging from 10mΩ to 2kΩ. Supplied complete Auto ranging ✓✓✓✓✓✓✓ with test kit and carry case. Pole test Two ✓✓ ✓ ✓✓✓✓✓ Three ✓✓ ✓ ✓✓✓✓✓ Four ✓✓ ✓ ✓✓ Current measurement and ART ✓ Total service accuracy ±0.5% ±2% ±2% ±2% ±2% ±2% ±2% ±2% Megger DET3TC NEW 1 Display 3 ⁄2 Digits ✓✓ ✓ ✓✓✓✓N/A Test Frequency in Hz 105 to 160 128 128 128 128 128 128 128 Voltage 50 50 50 50 25 or 50 25 or 50 25 or 50 25 or 50 Three and two terminal earth tester with Current in mA 50 10, 1 or 0.1 10, 1 or 0.1 10, 1 or 0.1 0.45 or 4.5 0.45 or 4.5 0.45 or 4.5 0.45 or 4.5 Attached Rod Technology (ART) Potential circuit rejection (pk-pk) 40 V 20 V 40 V 40 V 40 V 40 V 40 V 40 V Max current loop resistance 2 kΩ range 5 kΩ 10 kΩ 4 kΩ 4 kΩ 100 kΩ 100 kΩ 100 kΩ 100 kΩ Offering all the beneﬁts of the DET3TD but offering the 20 kΩ range >20 kΩ 100 kΩ 400 kΩ 400 kΩ option of selective, no-disconnect testing and earth leakage ✓✓ Power source Rechargeable battery testing using a clamp. Supplied complete with test kit and Dry Cell battery ✓✓✓✓✓ Hand-crank ✓ carry case (clamp optional). Weather proof IP54 ✓✓ ✓ ✓✓✓✓✓ Calibration certiﬁcate in the box ✓✓✓

All Megger earth testers are weather proofed to IP54 for ﬁeld use.

Megger DET2/2 DET3TC High resolution earth tester Megger DCM300E High resolution to 1mΩ. This level is required to measure resistivity to adequate depth on many substation and Earth leakage clamp communication sites. Measurement of the low earth values Measurement of leakage current. For stable readings down required on many installations, to meet Ground Potential to very low current value with a 10 mA resolution. Current Rise (GPR) requirements also, requires this resolution to measurement up to 300A. ensure valid results. Superior noise ﬁltering greater than 40V peak to peak to retain resolution under real test conditions.

Megger DET3/2 DET2/2 Megger DET10C and Megger Hand-cranked earth tester DET20C The DET3/2 gives complete independence from batteries or Earth resistance clamp testers mains power, with its hand-cranked generator. Checks for Earth resistance clamp meters are suitable for measuring excessive spike resistance or noise. earth resistance installations such as buildings, distribution pole and RF transmitter sites and for inspection of lightning Megger DET5/4D and protection systems. The DET20C offers memory and downloading capability. Megger DET5/4R DET3/2 Four terminal earth tester

With standard resolution to 10mΩ the DET5/4 instruments are used for medium sized earths and can also carry out DET20C resistivity testing. Simplicity of operation through auto ranging and auto-error detection.

Earth resistance testing Megger DET4TD NEW Model DET10C DET20C Earth resistance ranges auto ranging 0.025Ω to 1550Ω ✓✓ Four, three and two terminal earth tester Alarm High 0 to 1550 ohms ✓✓ Low 0 to 1550 ohms ✓✓ Simple to operate due to one button operation, Leakage current ranges 0.200 mA to 1.00 A ✓✓ 1.00 A to 35 A ✓✓ auto-ranging and auto-error detection, the DET4TD is DET4TD Auto ranging ✓✓ weatherproof and supplied complete with a lead and Datalogging capacity 116 records 8180 records stake kit. Data download ✓

16 Earth resistance testing Earth resistance testing 17 Low resistance measurement Megger DLRO® 10 10A low resistance ohmmeter

Comprehensive range of low resistance ohmmeters suitable for all power and battery applications. The DLRO10 offers a 0.1µΩ resolution with a maximum capability of 2kΩ. Fast testing ability means users can achieve results in less than 3 seconds. At only 2.5kg they are Low resistance measurement the smallest, lightest and simplest-to-use 10A low resistance Model DLRO600 DLRO200 DLRO10X DLRO10 BT51 ohmmeter available. Measurement ranges 1.9999mΩ 1.9999mΩ 20.00mΩ 19.999mΩ 19.999mΩ 2000mΩ 199.99mΩ 199.99mΩ 0.1µΩ to 999.9mΩ 0.1µΩ to 999.9mΩ 1.9999Ω 1.9999Ω BT51 auto ranging auto ranging 19.999Ω 19.999Ω 199.99Ω 199.99Ω 2A low resistance ohmmeter DLRO10 1999.9Ω 1999.9Ω Resolution 0.1µΩ 0.1µΩ 0.1µΩ 0.1µΩ 10µΩ Low resistance ohmmeter ideally suited for bond testing Accuracy <1% <1% ±0.2% ±0.2% ±1% applications, i.e. aircraft frames, electronic discharge and Current test range 10A - 600A 10A - 200A 0.1mA - 10A 0.1mA - 10A 2.0A Results storage 300 300 700 fuel tanks. Four terminal method of measurement ranges RS232 ✓✓✓ 0-20.00mΩ and 0-2000mΩ. High test current of 2A. Power source Mains ✓✓ Rechargeable battery ✓✓✓ Weight excluding leads 14.5kg 14.5kg 2.6kg 2.6kg 4.5kg

Megger DLRO600 BT51 600A low resistance ohmmeter Clips and leads for low resistance testing Provides the operator with high resolution, 0.1µΩ, Megger ohmmeters require test leads, two potential (voltage) and two current, to make low-resistance measurements. lightweight and portable method of performing on-site low In addition to individual current and potential (voltage) leads sets, duplex leads that combine current and potential resistance measurements. The unit can be used to test circuit connections in one lead are offered. A variety of terminations, C-clamps, Kelvin clips, ﬁxed point, and helical spring-point breaker contact resistance to IEC 62271-100, switch contacts, leads are available. busbars, joints, splices, fuses and rail bonds. The test current Battery testing is variable from 10A to 600A, in 1A steps, enabling the user Maximum to perform all the required test with a single instrument. For measurement of Lead type Termination test current Length Reference no Potential Single 2 pieces Hand spike N/A 2.0m 242021-7 5.5m 242021-18 DLRO600 9.0m 242021-30 Megger DLRO200 Current Single 2 pieces Current clip 10A 2.0m 242041-7 5.5m 242041-18 200A low resistance ohmmeter 9.0m 242041-30 Single 1 piece Heavy duty C-clamps 10A 5.0m 242144-16 Provides the operator with high resolution, 0.1µΩ, 8.0m 242144-26 Current and potential Duplex 1 piece DH2 handspike with helical sprung contacts 10A 6.0m 6111-023 lightweight and portable method of performing on-site low Current and potential Duplex 1 piece DH3 handspike with helical sprung contacts 10A 9.0m 6111-024 resistance measurements. The test current is variable from Current and potential Duplex Lead set DH1 handspikes with helical sprung contacts 10A 2.5m 6111-022 10A to 200A, in 1A steps, enabling the user to perform all Current and potential Duplex Lead set DH4 handspikes one with indicator light 10A 1.2m 6111-503 Current and potential Duplex Lead set DH5 handspikes one with indicator light 10A 2.5m 6111-517 the required test with a single instrument. The unit can be Current and potential Duplex Lead set DH6 handspikes one with indicator light (600V) 10A 1.2m 6111-022 used to test small circuit breaker contact resistance to IEC Current and potential Duplex Lead set 1.3cm silver-plated Kelvin clip 10A 2.0m 241005-7 62271-100, switch contacts, busbars, joints, splices, fuses and Current and potential Duplex Lead set 4.0cm silver-plated Kelvin clip 10A 2.0m 242006-7 5.5m 242006-18 rail bonds. 9.0m 242006-30 Current and potential Duplex Lead set Hand spikes with helical spring-loaded contacts 10A 2.0m 242011-7 5.5m 242011-16 DLRO200 9.0m 242011-30 Megger DLRO10X Current and potential Duplex Lead set Helical hand spikes with spring points and 10A 5.5m 242009-18 current push button switch 10A low resistance ohmmeter with test Current and potential Duplex Lead set Heavy duty straight ﬁxed contacts 10A 2.0m 242002-7 5.5m 242002-18 results downloading 9.0m 242002-30 Current and potential Duplex Lead set Heavy duty 5cm C-clamps 10A 2.0m 242004-7 The DLRO10X offers a 0.1µΩ resolution with a maximum 5.5m 242004-18 9.0m 242004-30 capability of 2kΩ. Fast testing ability means users can Current and potential Duplex Lead set Hand spikes with replaceable needle points 10A 2.0m 242003-7 achieve results in less than 3 seconds. At only 2.5kg it is the Current and potential Duplex Lead set Heavy duty 10cm C-clamps 100A 5.0m 242004-2-16 smallest, lightest and most sophisticated 10A low resistance 8.0m 242004-2-26 Current and potential Single Lead set Heavy duty 10cm C-clamps 100A 5.0m 242004-2-16 ohmmeter available. Current potential Duplex Lead set 2 x current leads with 7.6cm clamps 100A 10.0m 830255 2 potential leads with 2.5cm battery clips N/A 10.0m The DLRO10X has the capability of measuring inductive Current potential Duplex Lead set 2 x current leads with 4.5cm clamps 100A 15.0m 830258 loads such as transformers and motor winding. Availability 2 potential leads with 2.5cm battery clips N/A 15.0m Current potential Duplex Lead set 2 x 25mm2 current leads with clamps 600A 5.0m 6220-787 of readings can vary from a few seconds up to minutes 2 potential leads with clips N/A 5.0m depending on the inductance and resistance of the test item. Current potential Duplex Lead set 2 x 50mm2 current leads with clamps 600A 5.0m 6220-755 2 potential leads with clips N/A 5.0m The DLRO10X adds on-board memory, RS232 download Current potential Duplex Lead set 2 x 70mm2 current leads with clamps 600A 10.0m 6220-756 2 potential leads with clips N/A 10.0m capability, maximum setting and manual or automatic range Current potential Duplex Lead set 2 x 95mm2 current leads with clamps 600A 15.0m 6220-757 control to the features of the DLRO10. DLRO10X 2 potential leads with clips N/A 15.0m

18 Low resistance measurement Low resistance measurement 19

DLRO is a registered trademark of Megger Group Limited and/or its subsidiaries. Power quality Megger DCM1000P and DCM2000P Megger PA9plus Relay clampmeter These advanced clampmeters are particularly suited to Power quality analyser protection testing, due to its power frequency and true The PA9plus has enhanced standard key features including RMS measuring capabilities. For both single and three a fast digital signal processor to support future evolving phase systems. The DCM2000P also offers the functionality features and capabilities, a full 12MB of internal, non- of power meter, oscilloscope, harmonics meter and data volatile memory and incorporated auxiliary power input logger in one easy-to-use instrument. capabilities. The product offers testing to the relevant standards (EN50160, IEC61000 series, IEEE1159, IEEE519). PMM1 DCM2000P Data can be downloaded from the PA9 without interrupting the capability of instrument to record events. The optional 3 phase power measurement meter removable memory capabilities allows internal recorded Capable of measuring a.c. / d.c. voltage, a.c. primary and data to be copied directly to an external standard compact secondary current, power, power factor, reactive power, flash card using the same technology available with most of PA9plus today’s digital cameras. This means that without a computer phase angle and frequency of single and three phase on site, data can be copied, manually or unattended, from electrical systems with extreme accuracy. Integral solid state the instrument to external memory cards, increasing the time suitable for continuity and voltage sensing and effective instrument memory storage to the size of the harmonic measurement up to 49th harmonic. For detailed memory card used, and will program new configuration waveform analysis a high-speed capture function allow 20 setups in the same, simple manner. measurements per second. An RS232 data port allows bi-directional communication. PMM1 Megger MetReport Power quality analysis software Model 8 Mark7 MetReport is an extremely powerful, fully functional, and stand-alone report generation tool for the Megger PA-9Plus Analogue multimeter power quality analysers. Its primary purpose is to Megger MetReport screens The multimeter that has become the industry standard, dramatically improve and extend the reporting capabilities of our complimentary software packages. due to its robust construction. In today’s economy, time is money. Power and power quality professionals currently spend countless hours every year creating customized reports supporting their analysis studies. MetReport automates this tedious task while improving the accuracy and reliability of the entire reporting process. MetReport utilizes data files obtained from the PA-9 and PA-9Plus to rapidly produce completely customizable reports Model 8 Mark7 targeted to your particular applications and requirements. Some examples include: Power quality studies, harmonics analysis, power factor and energy consultation, tolerance curve studies (CBEMA/ITIC, SEMI F47, User Defined), auto data analysis pass/fail reports, EN50160 compliance, and IEEE/IEC Flicker. The key to quickly learning and using MetReport is the integrated wizard function. This wizard effortlessly takes you through the entire report creation, customization, and generation process. Several sample Title Name For more information on Megger products report templates are included for review, and may be modified to meet your specific needs. fill in your details on this card and return it Job title All reports are output as standard Microsoft Word to us in Dover. documents. Company Please send me the Megger Product ■ Megger SLM8 Address Catalogue on CD 8 channel recording volt-ammeter Please send me more information on the The SLM8 is a low cost, 8 channel paperless recording volt- following ammeter used for measuring and recording the true RMS values of up to four voltage channels and four current channels. It is the ideal investigative tool for utility trouble-shooters, service investigation groups, meter E-mail shop technicians and facility managers to identify and document the presence of tree-phase and single-phase voltage complaints utilizing associated load current Telephone information to locate the source of problems. SLM8 ■ For sale outside the EU only Fax 20 Power Quality Megger Pty Limited Unit 26 9 Hudson Avenue Castle Hill SYDNEY NSW 2125 AUSTRALIA T +61 (0)2 9659 2005 F +61 (0)2 9659 2201 E [email protected] Megger PO Box 15777 Kingdom of BAHRAIN T +973 17 411311 F +973 17 413399 E [email protected] Megger Limited 110 Milner Avenue Unit 1 Scarborough Ontario M1S 3R2 CANADA T 1 800 297 9688 (Canada only) T +1 416 298 6770 F +1 416 298 0848 E [email protected]

For comprehensive technical information on the entire Megger product range, visit: Megger SARL 23 rue Eugène Henaff ZA du Buisson de la Couldre www.megger.com 78190 TRAPPES FRANCE T +33 (0)1 30 16 08 90 F +33 (0)1 34 61 23 77 The products featured in this catalogue are available from: E [email protected] Megger PO Box 12052 Mumbai 400 053 INDIA T +91 22 26315114 F +91 22 26328004 E [email protected] Megger Limited Archcliffe Road Dover CT17 9EN UK T +44 (0) 1304 502100 F +44 (0) 1304 207342 E [email protected] Megger Product information, photographs and illustrations in this catalogue were current when 4271 Bronze Way approved for print. In a continuing effort to offer innovative products, Megger Limited reserves Dallas, TX 75237-1019 USA the right to change speciﬁcations, designs, models and prices without prior notice. T 1 800 723 2861 (USA only) T +1 214 333 3201 Megger is a Registered Trade Mark of Megger Limited. F +1 214 331 7399 E [email protected] Megger Valley Forge Corporate Center 2621 Van Buren Avenue Norristown PA 19403 USA T 1 800 723 2861 (USA only)

Megger Limited Archcliffe Road, Dover, CT17 9EN, England