Quick Start Guide

QUICK START GUIDE

READ ALL DIRECTIONS BEFORE PLUGGING 1 IN DISPENSER. 3 6 Important: Do not plug in dispenser until step 4. This guide is a general reference to help you quickly and easily set up your AquaCafé.®

SET COOLER IN DESIRED LOCATION. 2 Ensure cooler is located on a level floor, out of direct INSERT WATER BOTTLE. Use the slot on the right-hand TURN ON HOT sunlight and at least 4 inches TANK SWITCH. from a wall. side of the cooler to pull the door open. Wipe bottle cap with Once the hot tank has been paper towel. Peel the label off primed, turn on the hot tank the 5-gallon bottle. Remove switch that is located on the bottle probe from inside the back of the cooler. Water cooler. Insert probe into bottle, temperature will reach as high slide the bottle into cooler and as 198º F within 5 minutes. close the door. (Please wear gloves when setting up or replacing water bottles.) 7 PLUG IN DISPENSER. Dispenser should always be 4 installed within 6 feet of a power source. Dispenser should be plugged into a GFCI electrical outlet. Do not use extension cords. Ensure hot tank switch on back of unit is in the Off “O” position prior to plugging in. INSERT DRIP TRAY. Push the drip tray into the 5 pocket above the metal clip on the machine to snap it together.

WARNING TO USERS AND PARENTS: Adult supervision required. Equipment dispenses very hot water. PURGE WATER TANKS. The AquaCafé® has a self-priming feature that takes approximately 5 minutes to fill both the hot and cold tanks. After that time, dispense water from both the hot and cold tanks to confirm that they have filled.

Brewing Instructions 1 4

* K-cup

* K-cup S, M, L; 6 oz., 8 oz., 10 oz.

Brightness

Cold Water STEP 1 STEP 4 Place coffee cup When the water Hot Water on cupholder. temperature is low, the Water Dispense light will No Water Indicator 2 flash until temperature is reached. When it stops Unlock Indicator Ring flashing, press the Water Dispense button to brew Water Dispense coffee or tea.

5 Water Dispense Instructions • Hot Water – Press the Hot • Cold Water – Cold water is STEP 2 Water button and hold the default setting and the Press the K-Cup® pod for 1 second (the unlock unlock indicator ring will button to select coffee indicator ring will light up always be blue unless hot is volume. Press again to red.) Then press the selected (then it will be red). switch between cup sizes. Water Dispense button If the unlock indicator (6 oz., 8 oz. and 10 oz.)* to dispense hot water. ring is red, press the Cold *Unit is designed to default STEP 5 Water button, then press to the 8-oz. cup position. Open handle and • Extra Hot Water for the Water Dispense button. Once a different cup size ® discard used K-Cup Cooking Instant Otherwise, just press the is selected, it becomes the pod. Return K-Cup® pod default for the next brew. Noodles and Soups – Water Dispense button. funnel holder to the Press the K-Cup® pod machine. Machine will or button to select the • When the water bottle is 3 not brew without the water volume. When the empty, the No Water funnel holder. water temperature is indicator light will flash. low, the Water Dispense light will flash until temperature is reached. When it stops flashing, press and hold the Hot Water button for one second, then press the Water STEP 3 Dispense button. Open the handle, (Only available on put K-Cup® pod coffee models.) into the holder and close the handle. How to Load Water Bottles 1 2

Peel the label off the Insert probe into bottle, 5-gallon bottle cap. slide the bottle into Remove the bottle cooler and close probe from inside the door. the cooler. Cleaning Instructions

• Disconnect power cord • Once parts are clean, prior to cleaning the reassemble the unit. external portion of the Connect power cord brewer/cooler. and brewer/cooler is • The brewer/cooler housing ready to use. can be cleaned with a soapy, non-abrasive damp cloth. • The drip tray is dishwasher safe (top rack). To remove, grab drip tray and pull it out. • To clean the K-Cup® pod funnel, remove it from the brewer head assembly. Wipe out K-Cup® pod funnel holder with a damp paper towel. Inspect the needle assembly for clogging (coffee grinds); if clogged, use a paper clip to clear the needle. Place the K-Cup® pod funnel in top rack of dishwasher. CAUTION: Needle is sharp!