DOCSLIB.ORG

Digital Video – Guide to Connectors

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Digital Video – Guide to Connectors DIGITAL VIDEO – GUIDE TO CONNECTORS SDTV (Standard-Definition TV) HDTV (High-Definition TV) Standard-definition digital TV, defined as a 480i signal Digital TV standard that features increased horizontal & vertical (480 interlaced scan lines) presented 30 times per resolution (1280x720 or 1920x1080 pixels), a choice of second. (720x480 pixels, a 4:3 ratio). DVDs are progressive or interlaced scanning, & a widescreen aspect ratio of Standard Definition (480i), displayed as 480p. (total 16:9 that conforms to the widescreen visual format of modern resolution: 345,600 pixels) movies. The most common HD formats are 720p (720 progressively scanned lines) or 1080i (1080 interlaced scanned lines). (total resolution: 777,600 pixels for 720p and 2,073,600 for 1080p) Component Video The most common type of connector used for both SD & HD video, it uses three coaxial RCA cables and plugs color-coded red, green and blue. Note: Component video cables do NOT carry audio signals. You must connect separate audio cables (either analog or digital) to carry the sound signals. Component video cables keep the 3 color elements of a video signal separate from each (higher quality) Component-video can, with proper signal levels, give exactly the same quality as HDMI or DVI as long as the native resolution of the set is sent to it. Composite Video A single video connector that combines the color, brightness, and sync signals into one cable (hence "composite") using a single RCA connector. Often coded yellow; most common analog video connection between older VCRs and TVs (except RF connectors). Use composite video only if your TV, VCR or DVD player lacks S- video or component. NOTE: Composite video will not carry HD or progressive video. D-Sub (VGA or RGB) A type of multi-pin connector so-named because of its rough "D" shape, originally used in computer and data applications and now used in several variants for audio/video purposes. DVI (Digital Visual Interface) A large computer-like 18-pin connector that carries digital video signals, including HD. DVI digital video signals are protected by HDCP (High-bandwidth Digital Content Protection) protocol, which prevents you from copying high-quality digital video. DVI is gradually being replaced by the HDMI connector (see below). Although a DVI or HDMI connection eliminates several digital-to-analog and A/D conversions, it does not visibly improve image quality over correct component- video connections and may introduce incompatibilities in the HDCP anti-copy protocol (see HDMI). FireWire 400 (IEEE 1394; i.Link) First common in the computer world, this 4 or 6-pin connector is a link that carries compressed digital MPEG-2 video and digital audio for recording on a hard-disk. Found on some digital TV displays and set-top boxes, FireWire also carries an anti-copy code and can serve as a 2-way link between various devices in a network. Used to mount hard drives. Transfers data up to 400 Mb/s. (mostly replaced by FW 800 now) FireWire 800 (IEEE 1394b) The next generation of FireWire technology, doubles the throughput of the original FireWire interface to 800 Mbit/sec & dramatically increases the maximum distance of FireWire connections. HDMI (High-Definition Multimedia Interface) HDMI is a USB-like digital video connector that carries the same digital video signals as DVI but with a Dolby Digital surround sound bitstream. Copy protected with HDCP so you can't pirate high-quality digital video, it's compatible with DVI through DVI/HDMI adaptors. HDMI is an evolving standard and many incompatibilities in the digital "handshake" of the HDCP protection code still exist between HDMI-connected components, especially when routed through an A/V receiver or A/V processor. Thunderbolt (interface) A hardware interface that combines PCIe, DisplayPort and DC power in one cable. USB A-Type (3.0 and 2.0) Universal Series Bus is an industry standard for connecting cameras and other peripherals to computers. Initially rather slow (2.0 = 12 Mbps), 3.0 has dramatically increased transfer speed to 5 Gbps. The distinction is made in the color of the connector (blue for 3.0) USB mini-B, Micro-B, etc. Various smaller versions of USB have been developed for use with smaller cameras, phones, and devices. Note that you will need to examine very carefully what type of connector works with each device. S-video A small multi-pin connector cable that carries the chrominance (color) and luminance (brightness) video information separately. Not capable of carrying HD video signals but superior to composite video connections. Use this connector for better image quality if your TV, A/V receiver and VCR has S-video inputs and outputs. Mini-jack, mini-plug A miniature connector, in mono and stereo versions, commonly found on portable audio equipment for headphone and line-out audio connections. Small cameras also carry video on a third line (look for three rings) via Mini. RCA Connector By far the most common small audio or video connector, with a pin (male) plug and female jack. Uses 2-conductor shielded coaxial cable. Often found with yellow (video), red & white (audio). XLR (Balanced) Connector A secure, 3-wire connector found on all professional / semi-pro sound gear, enabling very long cable runs without hum pickup or frequency response losses. Must be used with matching balanced connectors on an A/V processor, preamp, or receiver to benefit from its hum-free traits. Over long cable runs, sound quality is better than shielded RCA coaxial cables. .
Load more

Recommended publications
  • MON1000AP Series(Projected Capacitive Monitor)
    Projected Capacitive Monitor Operations Manual MON1000AP Series Your Industrial Control Solutions Source _____________________ www.maplesystems.com For use with the following: • MON1000AP Series Projected Capacitive Touch Monitors Maple Systems, Inc. | 808 134th St. SW, Suite 120, Everett, WA 98204 | 425.745.3229 Projected Capacitive Touch Monitor Operations Manual: MON1000AP Series 2 TABLE OF CONTENTS TABLE OF CONTENTS ........................................................... 2 COPYRIGHT NOTICE ............................................................. 3 WARRANTY ......................................................................... 3 TECHNICAL SUPPORT .......................................................... 3 UNPACKING THE UNIT ......................................................... 3 SAFETY PRECAUTIONS ......................................................... 4 OVERVIEW OF MON1000AP SERIES ...................................... 5 PC CONNECTION ................................................................. 5 MOUNTING OPTIONS .......................................................... 6 SPECIFICATIONS .................................................................. 6 DIMENSIONAL OUTLINES .................................................... 8 I/O PORTS ......................................................................... 12 ON-SCREEN DISPLAY (OSD) OPERATION ............................ 14 ON-SCREEN DISPLAY PARAMETER ADJUSTMENT ............... 15 Projected Capacitive Touch Monitor Operations Manual: MON1000AP Series
    [Show full text]
  • Component Video with 2 Channel Mono Audio Extender AT-COMP150SR
    Component Video with 2 Channel Mono Audio Extender AT-COMP150SR User Manual Toll free: 1-877-536-3976 atlona.com Local: 1-408-962-0515 TABLE OF CONTENTS 1. Introduction 2 2. Features 2 3. Package Contents 2 4. Specifications 3 5. Panel Description 4 5.1. Sender Unit: AT-COMP150S 4 5.1.1. Input Panel 4 5.1.2. Output Panel 4 5.2. Receiver Unit: AT-COMP150R 5 5.2.1. Input Panel 5 5.2.2. Output Panel 5 6. Connection and Installation 6 7. Notice 7 8. Performance Guide 7 9. Safety Information 8 10. Warranty 9 11. Atlona Product Registration 10 1 Toll free: 1-877-536-3976 atlona.com Local: 1-408-962-0515 INTRODUCTION Atlona Technologies AT-COMP150SR can easily extend component (YPbPr) or composite (CVBS) video with 2ch mono audio over only one CAT5/6 cable. The AT-COMP150SR lets you extend signals to cover the distance up to 330m(1,000ft). The devices are composed of atransmitter and a receiver. The transmitter is installednear thevideo signal source, and the receiver is placed near the desired display, up to impressive 330m (1,000ft) away for composite (CVBS) video and analog 2ch mono audio.The AT-COMP150SR does nonteed external power supply which is easier for installation. FEATURES • Passive and no power required • Supports component (YPbPr) and composite (CVBS) video and 2 channel mono audio • Supports resolutions up to 720p/1080i (NTSC/PAL) • Transmission range up to 1,000 feet • Wall mountable Note: The length depends on the characteristics and quality of the cables.
    [Show full text]
  • CHE-HDBT2020 Pro AV/IT 4K 18G Hdbaset™ Extender TX/RX Kit up to 330Ft
    CHE-HDBT2020 Pro AV/IT 4K 18G HDBaseT™ Extender TX/RX Kit up to 330ft Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Comprehensive Connectivity assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Comprehensive Connectivity assumes no responsibility for any inaccuracies that may be contained in this document. Comprehensive also makes no commitment to update or to keep current the information contained in this document. Comprehensive reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Comprehensive Connectivity. © Copyright 2018 by Comprehensive All Rights Reserved. TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
    [Show full text]
  • Digital Visual Interface (DVI)
    Digital Visual Interface 1 Digital Visual Interface Digital Visual Interface (DVI) A male DVI-D (single link) connector. Type Digital computer video connector Production history Designer Digital Display Working Group Designed April 1999 Produced 1999 to present Superseded by DisplayPort General specifications Hot pluggable Yes External Yes Video signal Digital video stream: (Single) WUXGA (1,920 × 1,200) @ 60 Hz (Dual) Limited by copper bandwidth limitations, DVI source limitations, and DVI sync limitations. Analog RGB video (−3 dB at 400 MHz) Pins 29 Data Data signal RGB data, clock, and display data channel Bitrate (Single link) 3.96 Gbit/s (Dual link) Limited only by copper bandwidth limitations, DVI source limitations, and DVI sync limitations. Max. devices 1 Protocol 3 × transition minimized differential signaling data and clock Pin out A female DVI-I socket from the front Pin 1 TMDS data 2− Digital red− (link 1) Pin 2 TMDS data 2+ Digital red+ (link 1) Digital Visual Interface 2 Pin 3 TMDS data 2/4 shield Pin 4 TMDS data 4− Digital green− (link 2) Pin 5 TMDS data 4+ Digital green+ (link 2) Pin 6 DDC clock Pin 7 DDC data Pin 8 Analog vertical sync Pin 9 TMDS data 1− Digital green− (link 1) Pin 10 TMDS data 1+ Digital green+ (link 1) Pin 11 TMDS data 1/3 shield Pin 12 TMDS data 3- Digital blue− (link 2) Pin 13 TMDS data 3+ Digital blue+ (link 2) Pin 14 +5 V Power for monitor when in standby Pin 15 Ground Return for pin 14 and analog sync Pin 16 Hot plug detect Pin 17 TMDS data 0− Digital blue− (link 1) and digital sync Pin 18 TMDS data 0+ Digital blue+ (link 1) and digital sync Pin 19 TMDS data 0/5 shield Pin 20 TMDS data 5− Digital red− (link 2) Pin 21 TMDS data 5+ Digital red+ (link 2) Pin 22 TMDS clock shield Pin 23 TMDS clock+ Digital clock+ (links 1 and 2) Pin 24 TMDS clock− Digital clock− (links 1 and 2) C1 Analog red C2 Analog green C3 Analog blue C4 Analog horizontal sync C5 Analog ground Return for R, G, and B signals Digital Visual Interface (DVI) is a video display interface developed by the Digital Display Working Group (DDWG).
    [Show full text]
  • 5221 Manual 090519.Pdf
    User's Manual Remote Control Unit Power On/Off It's possible to use a remote controller within 3~5m, 60 degree of angle scope. You can use an extension receiver for a remote controller if it's far away from the system. The receiver in the system will not work when the extension reciever is connected. Insert battery 1. Pull out the insert part. 2. Insert battery after checking.. 3. Push in the Insert part. "+" Polarity HDS-1151L Connection(CAT5e/6 Mode) How to connect devices with splitter (►Input: Blu-ray Player, HD Stream Generator ►Output: PDP, LCD TV) I $.Note CATC cable is recommended for best results. Use both TMDS & DDC cable to use EDID/HDCP Please ask us if you want to use CAT5e/6 cable only not to use ECMD/HDCP Should re-set the settings of Transmitter & Receiver following the length of CAT5e/8 or resolut" on. For setting, please referto "How to set up CATSe/ff1 10 User's Manual How to set up CAT5e/6 mode Transmitter setting 1. Press & Select "Input 1" en the front 2. Press "Input 1" button 5 times. Please check if "beep" also sounds 5 times. 3. After pressing "Input 1" 5 times, you can hear 3 times buzzer sound. Entered "Boost setting mode" 4. How to set "Boost"? • Press Input 1 or Input 2 buttons Inputi: Make it lower & Input 2: Make it higher. • The setting value covers from 0 to 12 If you can hear 2 times buzzer sounds during pressing Input 1, it means that the setting value is arrived at the lowest level "0".
    [Show full text]
  • Sii9293 MHL/HDMI Receiver Data Sheet Silicon Image, Inc
    Data Sheet SiI9293 MHL/HDMI Receiver Data Sheet Document # SiI-DS-1107-A SiI9293 MHL/HDMI Receiver Data Sheet Silicon Image, Inc. March 2013 Copyright Notice Copyright © 2012-2013 Silicon Image, Inc. All rights reserved. The contents of these materials contain proprietary and confidential information (including trade secrets, copyright, and other Intellectual Property interests) of Silicon Image, Inc. or its affiliates. All rights are reserved and contents, (in whole or in part) may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior written permission of Silicon Image, Inc. or its affiliates. You may not use these materials except only for your bona fide non-commercial evaluation of your potential purchase of products and/or services from Silicon Image or its affiliates; and only in connection with your purchase of products or services from Silicon Image or its affiliates, and only in accordance with the terms and conditions stipulated. Copyright infringement is a violation of federal law subject to criminal and civil penalties. You have no right to copy, modify, transfer, sublicense, publicly display, create derivative works of, distribute these materials, or otherwise make these materials available, in whole or in part, to any third party. Patents The subject matter described herein may contain one or more inventions claimed in patents or patents pending owned by Silicon Image, Inc. or its affiliates. Trademark Acknowledgment Silicon Image®, the Silicon Image logo, Instaport®, the Instaport logo, InstaPrevue®, Simplay®, Simplay HD®, and UltraGig™ are trademarks or registered trademarks of Silicon Image, Inc. in the United States or other countries.
    [Show full text]
  • Game Capture Quick Start Guide
    E C D Y r. P b P R L T OU VIDEO T N E N PO M CO T U O IO D AU COMPONENT VIDEO IN AUDIO IN Y Pb Pr. L R A B Game console component cables (NOT INCLUDED) Game Capture Quick Start Guide A B Power off Xbox® 360 or PlayStation® 3. Connect a console specific C Connect the color corresponding D Connect the color corresponding E Connect USB cable Component AV cable* to the A/V port of the console. For Component Video cables between RCA Audio cables between the between the output PlayStation 3, you can leave the HDMI cable plugged in if you the outputs of Roxio GameCAP device outputs of Roxio GameCAP device on the Roxio GameCAP would like. For Xbox 360 the HDMI may need to be removed to and the Component Video inputs at and the Component Video inputs device and the USB2.0 make room for the Component AV cable. Next, plug the color the back or side of your TV. at the back or side of your TV. port of your laptop or PC. corresponding Component Video and RCA Audio cables to the inputs on the Roxio GameCAP device. *Console specific Component AV cable(s) are NOT INCLUDED. PlayStation3 If you were using HDMI or Composite AV cables on your PlayStation 3 you will need to reset the video output for Component AV cables by following these steps: A Go to Display Settings B Select Display Settings/Video Output Settings C Switch to Component/D-Terminal option D Use your TVs remote to change input to Component E Select (X) Enter to confirm change and confirm the change Check ALL the supported resolutions that your TV supports (480p/720p/1080i etc.) F Select “Set Audio Output Settings” G Change Audio to Audio Input Connector/SCART/AV MULTI H Select (X) Enter to confirm change Xbox 360 Tips: Use the remote control for the TV • If you are not able to see the preview video in the Roxio Game Capture software, power off and then power to change the input to Compone• nt on the console.
    [Show full text]
  • Bvh-20™ Bvr-20™ Bvd-20™
    ACTIVE-BALANCED SERIES ACTIVE-BALANCED SERIES Installation and Operation Manual ™ BVD-20 Component Video/Digital Audio Driver BVH-20™ Component Video/Digital Audio Hub Driver ™ BVR-20 Component Video/Digital Audio Receiver hank you for choosing an AudioControl Active- T Balanced product for your video and audio distribution needs. You are installing one of the most innovative custom installation products available. These units will allow you to transmit video and audio signals over standard Category 5 wiring by using the highest quality active circuitry. Please ® note that these products are primarily designed for installa- For Those Who Think Perfection Possible® tion by professional audio video companies so if any part of 22410 70th Avenue West this manual is not clear . STOP WHAT YOU ARE DO- Mountlake Terrace, WA 98043 ING! Contact your nearest audio video installation company Phone 425-775-8461 • Fax 425-778-3166 or call us and we will refer you to one. Plasma monitors and www.audiocontrol.com DVD players are too expensive to damage so don’t attempt anything you are unfamiliar with. ©2004 All Rights Reserved Now sit back, grab a cold beverage and take a moment to read through this manual before you charge off into the P/N 9130770 installation. 20 For Those Who Think Perfection Possible® ® ® ACTIVE-BALANCED SERIES ACTIVE-BALANCED SERIES Balanced Video Series Here are some of the cool features for your new balanced video and audio products: • Allows Simple Distribution of High-Quality Component Video and Audio signals up to 1000 feet (305 meters) • Uses Standard, Inexpensive, Twisted-Pair Cat-5 type Cabling • 300 MHz of video bandwidth - compatible with 480, 720, and 1080 formats • Will transmit High Definition (HD) signal up to 300’ via CAT-5 wiring • Can also transmit a digital audio or composite video signal • Standard EIA-568 RJ-45 Cat-5 Connection Jack • Adjustable Cable Compensation Circuit • Five Year Warranty The First Step In Your Installation Procedure FILL OUT AND SEND IN THE WARRANTY CARD! Also, save the invoice or sales slip as proof of purchase.
    [Show full text]
  • Quick Start Guide Autopatch Component Video (BNC & RCA) DAD Modules
    Quick Start Guide AutoPatch Component Video (BNC & RCA) DAD Modules Overview RGB Gain & Peaking** Specifications Component Video Distribution Amplifier Driver (DAD) Modules are available with BNC or RCA connectors. The modules have either one input and two outputs for Gain OFF Unity 1:2 distribution or one input and six outputs for 1:6 distribution of component video ON +0.85 dB signals. The single component video input is distributed to two or six outputs over standard cable runs of up to 500 ft. (152.4 m) for YPbPr and up to 250 ft. (76.20 m) for Peaking RGB with no additional equipment required. Each output can be independently OFF No peaking adjusted for gain and peaking to ensure the proper amount of compensation is ON 8 dB @ 150 MHz provided for each cable run. This guide contains complete information for this product. 8 dB @ 300 MHz Cable Length (max.) 250 ft. (76.20 m) YPbPr Gain & Peaking** Specifications Gain YPbPr (RCA) Model FG1052-19 RGB (BNC) Model FG1052-25 OFF Unity FIG. 1 Component Video DADs, 1:2 models ON +0.85 dB Peaking OFF No peaking ON 9 dB @ 37.5 MHz 9 dB @ 80 MHz Cable Length (max.) 500 ft. (152.4 m) ** Gain and Peaking are independent switches that allow the user to turn on or off the gain and peaking. G B R G B R G B R R G B R G B Installation RGB (BNC) Model FG1052-28 Mounting Options 1:2 Models Desktop – Attach the rubber feet (included) to the bottom of the module.
    [Show full text]
  • Input and Output Terminals Features DIGITAL PROJECTOR
    DIGITAL PROJECTOR MW571 Features Specifications Projection System DLP® Native WXGA (1280x800) resolution Native Resolution WXGA(1280 x 800) Brightness 3,200AL 3,200 ANSI lumens Contrast Ratio 13,000:1 13,000:1 high contrast ratio Display Color 1.07 Billion Colors Lens F=2.59~2.87, f=16.88~21.88mm) Full HD 3D support Aspect Ratio Native 16:10 (5 aspect ratio selectable) Throw Ratio 1.21~1.57 HDMI Image Size 60"-180" Network standby <0.5W Zoom Ratio 1.3x Lamp Type 196W Lamp (Normal/Eco/SmartEco/ 4000/6000/6500/10000 hours LampSave)* Keystone Adjustment 1D, Vertical +/- 40 degrees Projection Offset Vertical: 120% ±5% Resolution Support VGA(640 x 480) to WUXGA_RB(1920 x 1200) Horizontal Frequency 15~102KHz Vertical Scan Rate 23~120Hz HDTV Compatibility: 480i, 480p, 576i, 576p, 720p, 1080i,1080p Video Compatibility: NTSC, PAL, SECAM 3D Compatibility: Frame Sequential: Up to 60Hz 720p Compatibility Frame Packing: Up to 24 Hz 1080p Side by Side: Up to 24Hz 1080p Top Bottom: Up to 60Hz 1080p Computer in (D-sub 15pin) x 2(shared with component video) HDMI x 1 Monitor out x 1 Composite Video in (RCA) x 1 S-Video in x 1 Audio in (Mini Jack) x 1 Interface Audio out (Mini Jack) x 1 Speaker 10W x 1 LAN(RJ-45) x 1 USB (Type mini B) x 1 RS232 (DB-9pin) x 1 Input and Output Terminals IR Receiver x 1 (Front) 11.14” x 3.7” x 8.7” / 283 x 95 x 222 mm (with feet) Dimensions (WxHxD) 11.14” x 3.5” x 8.7” / 283 x 88.7 x 222 mm (without feet) 1 2 3 4 5 6 7 8 9 Weight 4.19 lbs (1.9 Kg) Power Supply AC100 to 240 V, 50 to 60 Hz Power Consumption Normal 265W, Eco
    [Show full text]
  • 17.3” HD & SD SDI Digital, Analog, HD HDMI/DVI (+HDCP
    LVB17 17.3” HD & SD SDI Digital, Analog, HD HDMI/DVI (+HDCP) •High & Standard Definition Video LCD Monitors 1080/720/576/480(@60/59.94/50) •3G includes 2x3G HD/SD SDI-Digital input/ HD HDMI/DVI (+HDCP) •HDMI/DVI inputs accepts up to 1080p HD •Modes: EGA to UXGA, NTSC/PAL/SECAM/NTSC4.43/PAL-M •Analog Inputs are Composite, Y/C, Component, RGB (SOG), DVI – I (Analog PC) •Aspect Ratio: 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: •Marker Display. •UMD Support. •Color Temperature – User, VAR, 11000K, 9300K, 6500K, 5400K, 3200K SPECIFICATIONS Active Area (Diagonal): 17.3”/ 439 mm MODES High & Standard Definition Video Modes: 1920x1080p(50/60/30psf/25psf/24psf/30/25/24),1920x1080i(50/60), 1280x720p(50/59.94/60), 480i(59.94),576i(50) Digital, VESA VGA, DVI/HDMI *24psf/23.98psf signal format is not supported in “UNDERSCAN ” Mode. PC Video Modes: EGA, VGA, SVGA, XGA, WXGA, SXGA, WSXGA, UXGA Standard Definition Video Modes: NTSC/PAL/SECAM/NTSC4.43/PAL-M Scanning Modes: Under/Over/Zero/Pixel to Pixel Scanning INPUTS Digital Video Inputs: 3G HD SDI (@50/59.94/60), HD HDMI/DVI (+HDCP) Digital Video Inputs: Digital Visual Interface, VESA & SMPTE Rates. Analog Video Inputs: Composite, Y/C, Component, RGB (SOG), DVI – I (Analog PC) PICTURE Aspect Ratios: Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1 Picture-in-Picture : Analog (Composite1, 2, 3, YPbPr, GBR, PC), SDI 1 inputs + SDI 2, Digital (DVI, HDMI) input PIP Picture-by-Picture: Side by Side split screen display Pixel (RGB Trio) Arrangement: 1920 H x 1080 V Pixels RGB strip arrangement (2,073,600 Pixels,
    [Show full text]
  • PCI Express HD Video Capture Card 1080P – HDMI / DVI / VGA/ Component Startech ID: PEXHDCAP
    PCI Express HD Video Capture Card 1080p – HDMI / DVI / VGA/ Component StarTech ID: PEXHDCAP The PEXHDCAP PCI Express HD Video Capture Card enables you to capture high-definition video and audio from an HDMI®, DVI or Component (1080p) source to your computer through a PCI Express expansion slot. Support for full 1080p video input, as well as HDMI® and RCA stereo audio makes this HD capture card the perfect solution for creating digital copies of your videos for editing and compiling. The added versatility of 3 different video inputs (HDMI®, DVI, Component), plus the ability to capture VGA input using the included DVI to VGA adapter, or DisplayPort® using an active adapter, gives you the freedom to connect a multitude of audio-video devices to your computer, quickly and easily. This PCI Express capture card supports NTSC and PAL systems, and comes complete with an easy to use video capture software suite, allowing you to record video or take still screenshots and save them to your PC. Backed by a StarTech.com 2-year warranty and free lifetime technical support. This Product will not record HDCP protected content. Active DisplayPort Adapter not Included System Requirements: CPU: Intel Core2 Duo (for 720p capture) Intel Core i5 (For 1080pcapture) Memory: 1 GB Video: DirectX 9.0c Compatible Graphics Card Applications Record and convert video from camcorders, game consoles (XBox 360™) or cameras, into digital format Import recorded videos into your computer system for editing, to make your own your own compilations DVI/VGA/HDMI Screen capture
    [Show full text]