<<

Palm sander information

complete wear wear your safety a training glasses mask

Operate only with instructor’s permission and after you have received instruction.

Remove any jewelry, eliminate loose clothing, and confine long hair.

Make sure all guards are in place and operating correctly.

Always use proper eye protection and a dust mask as dust particles can irritate the eye s and lungs.

All materials should be inspected for defects such as warps, knots and foreign objects (nails, screws, etc). If sanded it is possible that such objects may become projectiles risking damage to the sander or to the user.

Do not use that is larger than needed. Extra paper that extends beyond the sanding pad can cause serious lacerations.

Never operate this tool with perforated paper unless the dust collection bag is in place. The perforations allow dust to be transferred to the dust collection bag. Never use the sander for wet sanding. Using this tool for this purpose could cause electric shock.

Sanding of lead based is not recommended due to the difficulty of controlling the contaminated dust. This is covered under the hazardous material handling documents of WHMIS.

Empty the dust collection bag regularly. It is especially important when sanding resin coated surfaces such as polyurethane, , shellac, etc. as the residue from such compounds can spontaneously combust if left in the collection bag.

A dust mask or respirator should be worn by all persons entering the work area.

All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the project.

Keep your machine as clean as possible by wiping with a clean cloth and blowing through it with air every 5 hours of use.

Do not operate the sander for extended periods of time as the vibrations can cause nerve damage to fingers, hands and arms. • --_lng Basics Combine power­ and hand-sanding for good results with no wasted time

BY DAVID SORG

he course of true love never did lun smooth, according to Shakespeare, and smoothing true rarely causes love to course, it would seem. Bore- Tdom and fe ar are more common feelings among woodworkers when sanding their projects. But proper sanding is a crucial part of , so please read on for some tips and techniques that will turn your boredom into serenity, and your fear into fun. I'll stick my neck out and state that no project should be finished without first be­ ing sanded. Even if you are a hero with the handplane or skilled with the scraper, you won't be able to get a surface that is uni­ formly smooth and with an even sheen. In­ evitably, there will be tiny depth changes from adjoining passes of the blade, while the sole of the can burnish strips of wood that may show up after a stain or a clear finish has been applied. Those who rely solely on power tools will inevitably be left with planer- and ­ knife marks and fibers crushed by the feed rollers. tables can leave gouges and scratches, and assembly often produces some errant glue splotches. All of these TOOLS FOR SAN DING blemishes should be removed before a fi n­ ish is applied, and sanding is the best way Achieving a well-sanded surface in the to achieve this. The most efficient way to most efficient way requires a combination sand a su rface is with a combination of of power-sanding and hand-sanding. power-sanding and hand-sanding

Power-sanding comes first Of course, you could do all of your sanding by hand, but why? Even if you use power RANDOM-ORBIT SANDERS sanders wherever practical, there will be enough hand-sanding on almost any pro­ These machines are great for removing ject to give you plenty of hand-done satis­ large amounts of wood from large surfaces. They are less suitable for small faction. Power sanders deliver results with areas, and their shape prevents them much greater speed, and with minimal from reaching into inside corners. practice they'll also deliver a flatter surface than sanding by hand alone. The good news is that unlike much of your other shop equipment, quality sand­ ing tools will not cost you much. I strongly suggest you get a random-orbit sander. A pad sander also is useful, and I'll explain why a detail sander is optional. Don't forget a dust mask and hearing protection.

Fast stock removal with a random­ orbit sander-Random-orbit sanders are wonderful machines. The pad has dual motion: It spins in a circle as well as in an eccentric orbit. These sanders are great for rapidly smoothing and leveling raw wood. Five-in.-dia., palm-held models are most common, but you also can buy 6-in.-dia., two-handed versions.

Most random-orbit sanders have holes Less aggressive than rand om-orbit in the pad (and, of course, in the sandpa­ sanders, pad sanders are easier to per) for dust extraction. The sanding disks control, which makes them suitable for narrower and more are backed with either pressure-sensitive confined areas such as table legs adhesive (PSA), which is cheaper, or and the insides of cabinets. reusable hook-and-loop systems. Older sanders need to be switched on when already resting on the surface of the wood, or they will spin too fast and gouge the wood when you try to bring them in

HAND-SANDING TOOLS

Sand by hand to finish the job. For flat areas, use a backing block made from cork or rubber to prevent your fingers from applying uneven pressure. To keep moldings crisp, use commercial rubber profiles or shop­ made foam ones to back the sandpaper.

PhQ(os, except where noted: Mark Schofield NOVEMBER/DECEMBER 2004 41 Sanding with power

POWER-SANDING FLAT SURFACES

WIDE PARTS Again, a random-orbit sander does well here. Note: It is easier to sand parts LARGE PANELS such as table aprons before assembly. With their wide contact surfaces, random-orbit or table legs, as well as on the insides of sanders are na turally at home on large panels. cabinets and in other confined spaces.

The right grit fro m start to finish­ With either type of sander, I'd rather start with 150-grit than 120-grit paper on most NARROW PARTS pieces, even though it may take longer to remove some marks. For wood that On smaller pieces such as is already in good shape, especially with the parts for a frame, a pad sander gives more thin-veneered sheet goods, I start with 180- control than a random­ grit paper. orbit sander. Note: The grits I refer to here are based on t11e FEPA scale, which uses the prefix P, ratl1er than the alternate CAMI, or C, scale. for a landing. Most new models have elec­ gain more control with less fatigue. Also, In t11e 150 to 220 range, the grits are nearly tronic speed conu'ol, which allows you to sand subassemblies before glue-up. It's equivalent, but it's best to work with the lift the sander to apply it to an adjacent sur­ much easier to sand a frame-and-panel, t11e paper from one scale. face without having to turn it off and restart aprons of a table, or a drawer's parts before Don't continue using a piece of sandpa­ it each time. they're assembled. per until the sand is all gone and there isn't Random-orbit sanders will do a speedy anything left but the paper. That's a fa lse job on large surfaces and bring two pieces Pad sanders- give more control in economy if you're charging for your time; of wood into the same plane. However, at small areas Pad sanders, also called and if you're woodworking fo r fun, well, the edges of a workpiece, keep the major­ palm sanders or finish sanders, use a sim­ you're taking away a bunch of it. Move to a ity of the pad on the wood, or you'll risk ple orbital pattern, and the pad does not fresh section of sandpaper as soon as you dishing or rounding over the edge. By the rotate, giving a much slower sanding ac­ feel it stop cutting or start to clog, or when same token, keep these sanders moving; tion but greater control. The pad al­ it requires you to exert more pressure. don't concentrate on one spot, or you lows the tool to get fairly close to inside Having experienced this the hard way, let could create a little bowl. corners (but beware getting it too close, me assure you that it's very important to Orient your project, if you can, so t11at where it quickly can chew up t11e adjacent vacuum and/or blow off the entire piece you're working horizontally. By letting the surface). This type of sander works well on between grits. I do botl1, t11en wipe it with weight of the sander work for you, you'll smaller surfaces like the edges of shelves a tack cloth. One piece of 150 grit being

42 FINE WOODWORKING Photo, this page (top left):Matthew Gardner CHECK YOUR PROGRESS

With the workpiece lit by a strong light, wipe the wood with some mineral spirits and check the surface for obvious scratches and rough areas.

swirled around on your 220-grit pad will make you curse when you see the results.

Tips for efficientsanding-With a cabi­ net, begin sanding on the inside: If you start with the inside while you're fresh, you'll take a few extra minutes to do it right in­ SANDING DETAILS stead of skimping on it at the end. For veneered , you can start and stop with ISO-grit paper if the inside will be minimally seen or used. Use a hand­ sanding block on the corners and on any more visible areas such solid-wood edging. Devote more time to visible areas and those likely to be touched. Ending with ISO-grit paper is fine for , but go to 220 grit for . On end grain, go one grade finer so that it doesn't absorb the stain or clear finish as deeply.

How do you know when you're finished A quicker way to sand moldings. power-sanding? Wipe some mineral spirits Detail sanders come with an assort­ on the surface and sight across the wood ment of different pads designed to fit toward a strong light. Pay no attention to most profiles. The radius on the beautiful color that appears; instead, this pad matches the of the look at the surface for telltale scratches, es­ apron (left). One disadvantage of detail sanders is that the adhesive-backed pecially the ugly orbital kind. You would sandpaper frequently comes away like to see a uniform appearance with no from the pad (above). rough areas or single outstanding scratches. Sometimes it's easiest to see this right at the moment of evaporation, when the ruts of

NOVE M BERID E C E M BE R 2004 43 Sanding

HAND-SANDING FLAT SURFACES

FLAT AREAS

To maintain a flat surface, you EDGES should always use a backing block when sanding large areas. Break the edges on a project not only to reduce future damage but also to prevent finish from forming a mound at the edges.

END GRAIN the scratches will still be shiny with fl uid

To lessen end grain's darker while the top surface is dull with dryne s. appearance when the workpiece is If you take this step, you'll avoid the agony finished, burnish the wood and fill the that many experience when they apply a pores by sanding end grain up to 320-grit paper. stain only to ee the scratches jump our.

Sanding details and molding After sanding the wide-open areas, how should you sand profiled areas? Manufac­ turers advertise detail sanders as the an­ swer to sanding any shape and any SANDING confined space. These sanders come with AFTER GLUE·UP a variety of pads designed to fit diffe rent

No matter how thoroughly you profiles. Although I own a couple of detail sanders, I could live without them, mostly sand parts prior to assembly, because it's too much trouble to constantly there still will be small areas change tl1e paper on tl1em; by tl1eir nature, to touch up by hand-sanding they put their sanding action into a small with 220- or 320-grit paper. area of sandpaper tl1at wears very quickly. Areas where glue was removed Most of the time I think it's quicker to do with a damp cloth may need moldings, interior corners, and other small smoothing (top), or there may areas by hand. To keep the moldings crisp, be two pieces that don't join in use commercial lUbber profiles that cover a perfect plane (bottom). To most convex and concave shapes, or you avoid cross-sanding where can make your own profile blocks from grain intersects, mask off one pieces of fo am-insulation panel. of the pieces. The end grain on raised panels requires a special sanding sequence to tone it into the rest of the panel. tart by sanding across tl1e grain with 150- or 180-grit paper to deal witl1 tl1e rough texture. Then sand the en-

G 44 FI IE WOODWORKII Photo, this page (lOp left ): MatThew Gardner HAND-SANDING DETAILS

Rubber profiles. Using a rubber pad that fits the molding helps keep the edges of the pro­ file sharp.

CURVE CONSCIOUS

Insulation foam shaped to match the panel's pro­ file makes a good backing for sandpaper (above). The end grain may need to be sanded with paper that is one grade coarser than that used on the rest of the panel, in this case, 1.50 grit (left). Then sand the entire panel with 220 grit before removing any cross-grain scratches on the end­ grain sides using 320-grit paper with the grain.

Sanding curves by hand. Contour the paper to fit curves in the wood.

tire profile on all four sides of the panel with 180- or 220-grit paper. Last, sand just the end grain with 320-grit paper, going with the grain in short strokes to eliminate any cross-grain scratches and to lessen the end grain's ability to absorb finish.

Final hand-sanding gives a finishing touch they also can be used for wet-sanding be­ allowing the andpaper to last longer and o matter how much you are able to use tween coats of finish. Other choices in­ and more smoothly, tearates are waxy machines fo r the initial stages of sanding, clude cork block or wood blocks faced and interfere with many water-based fin­ you'll want to give each surface some final wid1 a sheet of cork. ishes, causing fisheyes on the surface. If sanding by hand. Primarily, this is to get rid If you plan to u e a water-based stain or you're planning to use a water-based fin­ of the small orbital scratches left by the ma­ clear firlish, there are a couple of extra steps. ish, check with the manufacturer to see chines, replacing them with smaller, finer After d1e final hand- anding, wipe down the whether the fi ni h is compatible with scratches d1at are all parallel to d1e grain of piece with a damp sponge. After the wood stearated sandpaper. Last, as I recommend the wood and hence less noticeable. dries, very lighdy sand with the same-grade for all finishing methods, test each sanding You should back up the andpaper with paper you finished with, but be careful to tep on a sample board. 0 a sanding block wherever possible to remove only the raised grain. Watch out for maintain a flat surface. I find d1e palm-sized sandpaper coated wid1 stearates: AJd10ugh David Sorg is a finisher and artist who lives in rubber blocks most convenient because d1ey do a better job at preventing clogging, Denver,Colo.

NOVEMBER/DECEMBER 2004 45 Palm Sander Safety Quiz Name: Check the box next to the most correct answer 1 When should permission be obtained from your instructor to operate the palm sander? in all situations never when sanding lead paint Get your quiz results faster! when the stock to be sanded is small Do your safety quiz online. 2 What should you wear when operating a palm sander? no jewelry no loose clothing confined long hair all of the above 3 When must proper eye protection be worn to operate the palm sander? when sanding when sanding always never 4 Why do you make holes in the sandpaper before using it? to allow for more vigorous sanding to allow for better dust collection to ensure that the paper does not fall off to save paper 5 What is not recommended to be sanded with the palm sander because it may create contaminated dust? lead 6 Why must the dust bag be emptied regularly when sanding resin coated surfaces such as paint and varnish? it uses more electricity sand paper loses its grittiness the residues from such compounds may self ignite and cause fire none of the above 7 Why must the user ensure that the surface being sanded is free of nails, screws and other metal pieces? lead contained in nails or screws is a contaminant metal shards could break off and become a projectile so that the operator doesn’t need to wear safety glasses metal pieces will make your stock look bad 8 Why should the sander only be operated for short periods of time? it draws too much power it is too noisy vibration caused by the operating action of this tool may cause permanent injury to fingers, hands and arms you will use too much sandpaper 9 Why is it important that the user wear Personal Protective Equipment (PPE) when using the palm sander? dust particles from sanding can irritate your eyes and lungs the sander is not noisy the sander does not produce any dust all of the above 10 What must you do before connecting the sander to the power source? Choose all that apply. ensure that the power button is in the OFF position ensure that the sand paper is secured properly to the sanding pad with attached clamps ensure that the dust collection system is connected ensure that the power cord is not frayed or damaged