DOCSLIB.ORG

For Use on Any Core Drilling Machine

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
For Use on Any Core Drilling Machine 2013-2014 1 .com QR CODES Order On-Line & SAVE! Pages in our catalog have these QR codes – if you scan them with your smart phone they will take you directly to that product page on our website, showing specs, features, benefits, videos, this will give you the best source of information and purchasing, and specials anywhere! SOCIAL MEDIA THAT ACTUALLY MEANS SOMETHING TO YOU! You’ll actually GET something from our Sites! Not just your typical social media Promoting – These sites ARE worth your time! Save Money! Take advantage of Specials ONLY found HERE! Stay connected and get your new info easily - Learn How to on our Video’s! Linkedin FaceBook Twitter YouTube • Easy to use website – Find your product fast! • Wide variety of Choices – Compare Prices and Products! • Get order confirmations, tracking numbers • Pay on our SSL Secure checkout or use PAYPAL 2 3 CONTENTS DIAMOND SAW BLADES / SAWING EQUIPMENT DIAMOND CORE DRILL BITS HIGH SPEED BLADES .........................................................................6 - 7 DRY DRILLING CORE DRILL BITS ...................................................34 - 35 HIGH SPEED SAWS ...........................................................................8 - 9 VACUUM DRY DRILLING CORE DRILL BITS ..................................36 - 37 MASONRY SAW BLADES ...............................................................10 - 11 WET DRILLING HAND HELD CORE DRILL BITS .............................38 - 39 MASONRY SAWS ...........................................................................12 - 13 WET DRILLING CORE DRILL BITS ..................................................40 - 41 TURBO BLADES ..............................................................................14 - 15 THREADED BITS, BARREL EXTENSTIONS & THREADED CAPS ............ 42 CUT-N-BREAK ........................................................................................ 16 SPECIALTY BITS ..................................................................................... 43 DIAMOND CHAINS ............................................................................... 17 MARBLE & GRANITE DIAMOND BITS .................................................. 44 SMALL DIAMETER BLADES .................................................................. 18 NON-CORING BITS ................................................................................ 45 DIAMOND CUP WHEELS ...................................................................... 19 WATER TRAP RINGS ............................................................................. 45 CRACK-CHASING V-SHAPED BLADES .................................................. 20 CARBIDE TIPPED CORE BITS ................................................................. 46 TUCK POINT BLADES ............................................................................ 21 TILE AND STONE BLADES .................................................................... 22 DRILLING EQUIPMENT REFRACTORY BLADES AND BITS ........................................................ 23 M1 DRILL RIG .................................................................................48 - 49 TILE SAWS ......................................................................................24 - 25 M1-AA-15 DRILL RIG ............................................................................ 50 DRY CUTTING WALK BEHIND SAW BLADES ................................26 - 27 M-180 DRILL RIG ................................................................................... 51 CURED CONCRETE BLADES .................................................................. 28 M-2 DRILL RIG ................................................................................52 - 53 ASPHALT AND GREEN CONCRETE BLADES ........................................ 29 M-3 STAIR RIG ................................................................................54 - 55 PLUNGE CUT BLADES ........................................................................... 30 M-4 RIG ..........................................................................................56 - 57 GRINDING DISKS ................................................................................... 31 M-6 DRILL STAND ..........................................................................58 - 59 HYDRAULIC SAWING / DRILLING ......................................................... 60 ULTIMATE DRILLING MACHINE (U.D.M.) ............................................ 61 ELECTRIC MOTORS ............................................................................... 62 HAND HELD DRILL MOTORS ............................................................... 63 DRILL RIG COLUMNS & MASTS ............................................................ 64 EXTENTIONS & ADAPTERS ................................................................... 65 DRILLING ACCESSORIES ....................................................................... 66 161 Reaser Ct. Elyria, Oh 44035 DUSTLESS TECHNOLOGIES ................................................................... 76 Phone: 1-800-446-9001 • 440-365-1774 • Fax: 440-365-1717 [email protected] • www.dynatech.com DYNATECH COMPANY INFORMATION CUSTOMER SERVICE & WARRANTY INFO ........................................... 78 DYNATECH APPAREL ............................................................................ 79 4 5 HIGH Three Qualities to Choose From: QUALITY GRADE SPEED BLADES For Hand-Held Saws .312 (5/16") Tall .375 (3/8") Tall .437 (7/16") Tall Dynatech High Speed Blades are specially made for hand held gas and electric saws and are available in Economy, ECONOMY (E) HEAVY DUTY (H) PREMIUM (P) Heavy Duty and Premium Series. Laser welding of the .312 (5/16") Diamond .375 (3/8") Diamond .437 (7/16") Diamond diamond segments assures superior strength and provides Cutting Depth. Cutting Depth. Cutting Depth. fast smooth cutting with long service life. These blades have the highest level of performance and will make A very good blade for the A higher diamond content The highest diamond content even the toughest sawing job easier and more occasional user. and a taller diamond depth and tallest diamond cutting profitable. Dynatech High Speed Blades are makes this our most popular depth make this blade the excellent for cutting a wide variety of materials saw blade. choice of professional cutters. such as concrete, brick or block, expansion joints, precast, prestressed materials and much more. May be used wet or dry. APPLICATION - MATERIAL TO BE CUT Laser Dry-Cutting Highspeed LDH-1 For hard material, non-abrasive material, granite, marble, quarry tile. EXAMPLE FOR ORDERING A SAW BLADE: Choose a size Choose an application Choose a quality LDH-3 For medium hard brick or block and cured concrete with hard aggregate. 14" x .125 x 1" or 20mm LDH-5H LDH-5 For general purpose, most all brick, block, and cured concrete. LDH-7 For abrasive materials, green concrete, asphalt, light-weight block and sandstone. BLADE SIZES ECONOMY HEAVY DUTY PREMIUM Price Price Price 12" x .125 x 1" or 20 mm $79 $99 $129 Need More Help? 14" x .125 x 1" or 20 mm 99 139 179 Just give us a call: 1-800-446-9001 16" x .125 x 1" or 20 mm 149 199 249 Or go to: WWW.DYNATECH.COM 6 7 HIGH SPEED SAWS Scan this qr code for more info on the K970. Husqvarna K760 (14") - $895 Husqvarna K970 (14") - $1,159 P/N 967181002 P/N 966477101 An all-around, all-purpose power cutter For the demanding contractor who with an ergonomic design and safety performs highway or demolition work. features. It has a low cost to operate and The machine has added power to high production rates, when compared complete the job and a long working life. to other power cutters in its class. APPLICATIONS TECHNICAL SPECIFICATIONS APPLICATIONS TECHNICAL SPECIFICATIONS Blade, in (mm) 12/14 (305/350) Blade, in (mm) 14/16 (350/400) • Can be used for a variety of cutting applications • Perfect for cutting concrete curbs and precast work, also Cutting depth, in (mm) 4/5 (100/127) Cutting depth, in (mm) 5/6 (127/152) including curbstones and pavers in landscaping, metal/ great for general bridge work. Power, hp (kW) 5 (3.7) Power, hp (kW) 6.4 (4.8) pipes in installation work, concrete in buildings as well • Can be used for flat work with the KV 970/1260 cart. Power/weight ratio, hp/lbs (kW/kg) .24/.23 (.39/.38) Power/weight ratio, hp/lbs (kW/kg) .26/.25 (.44/.41) as roadwork applications. • When used with the KV 760 cart, it can be utilized for Displacement, cu in (cc) 4.5 (74) Displacement, cu in (cc) 5.7 (94) small flat work jobs. Weight without fuel and cutting equipment, lbs (kg) 20.7/21.6 (9.4/9.8) Weight without fuel and cutting equipment, lbs (kg) 24.2/26 (11/11.8) Fuel capacity, qt (l) .95 (.9) BENEFITS Fuel capacity, qt (l) 1.1 (1.0) Air-cooled 2-stroke engine Yes • New generation Active Air Filtration™ efficiently cleans air. Air-cooled 2-stroke engine Yes ™ ™ BENEFITS Active Air Filtration Yes • Engine with X-Torq™ produces more power, higher torque Active Air Filtration Yes X-Torq® Yes and 75% fewer emissions. X-Torq® Yes • New generation Active Air Filtration™ efficiently cleans SmartCarb™ Yes • SmartCarb™, a built-in automatic filter compensation, SmartCarb™ Yes air. Filter inspection required only with normal DuraStarter™ Yes maintains high power and lowers fuel consumption. DuraStarter™ Yes maintenance until filter needs to be replaced. EasyStart™ Yes • Easy to start, due to the decompression valve. EasyStart™ Yes • Engine with X-Torq™ produces more power, higher Reversible cutting arm Yes • DuraStarter™, the dust-sealed
Load more

Recommended publications
  • UNIFORM STANDARD SPECIFICATIONS for PUBLIC WORKS CONSTRUCTION
    UNIFORM STANDARD SPECIFICATIONS for PUBLIC WORKS CONSTRUCTION SPONSORED and DISTRIBUTED by the 1998 ARIZONA (Includes revisions through 2010) FOREWORD Publication of these Uniform Standard Specifications and Details for Public Works Construction fulfills the goal of a group of agencies who joined forces in 1966 to produce such a set of documents. Subsequently, in the interest of promoting county-wide acceptance and use of these standards and details, the Maricopa Association of Governments accepted their sponsorship and the responsibility of keeping them current and viable. These specifications and details, representing the best professional thinking of representatives of several Public Works Departments, reviewed and refined by members of the construction industry, were written to fulfill the need for uniform rules governing public works construction performed for Maricopa County and the various cities and public agencies in the county. It further fulfills the need for adequate standards by the smaller communities and agencies who could not afford to promulgate such standards for themselves. A uniform set of specifications and details, updated and embracing the most modern materials and construction techniques will redound to the benefit of the public and the private contracting industry. Uniform specifications and details will eliminate conflicts and confusion, lower construction costs, and encourage more competitive bidding by private contractors. The Uniform Standard Specifications and Details for Public Works Construction will be revised periodically and reprinted to reflect advanced thinking and the changing technology of the construction industry. To this end a Specifications and Details Committee has been established as a permanent organization to continually study and recommend changes to the Specifications and Details.
    [Show full text]
  • Slope Stability Reference Guide for National Forests in the United States
    United States Department of Slope Stability Reference Guide Agriculture for National Forests Forest Service Engineerlng Staff in the United States Washington, DC Volume I August 1994 While reasonable efforts have been made to assure the accuracy of this publication, in no event will the authors, the editors, or the USDA Forest Service be liable for direct, indirect, incidental, or consequential damages resulting from any defect in, or the use or misuse of, this publications. Cover Photo Ca~tion: EYESEE DEBRIS SLIDE, Klamath National Forest, Region 5, Yreka, CA The photo shows the toe of a massive earth flow which is part of a large landslide complex that occupies about one square mile on the west side of the Klamath River, four air miles NNW of the community of Somes Bar, California. The active debris slide is a classic example of a natural slope failure occurring where an inner gorge cuts the toe of a large slumplearthflow complex. This photo point is located at milepost 9.63 on California State Highway 96. Photo by Gordon Keller, Plumas National Forest, Quincy, CA. The United States Department of Agriculture (USDA) prohibits discrimination in its programs on the basis of race, color, national origin, sex, religion, age, disability, political beliefs and marital or familial status. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program informa- tion (Braille, large print, audiotape, etc.) should contact the USDA Mice of Communications at 202-720-5881(voice) or 202-720-7808(TDD). To file a complaint, write the Secretary of Agriculture, U.S.
    [Show full text]
  • Geotechnical and Pavement Engineering Report Thorp Prairie Road Evaluation and Design Kittitas County, Washington
    GEOTECHNICAL AND PAVEMENT GEOTECHNICAL REPORT ElliottENGINEERING Bridge No. 3166 REPORTReplacement Thorp PrairieHWA JobRoad No. Evaluation 1996-143-21 and Design Kittitas County, Washington HWA ProjectPrepared No. for2012-105-21 ABKJ, INC. Prepared for PacifiCleanApril Environmental 4, 2003 LLC February 1, 2013 TABLE OF CONTENTS 1.0 EXECUTIVE SUMMARY ..............................................................................................1 2.0 INTRODUCTION..........................................................................................................1 2.1 GENERAL.......................................................................................................1 2.2 PROJECT UNDERSTANDING............................................................................1 3.0 FIELD AND LABORATORY TESTING............................................................................2 3.1 FALLING WEIGHT DEFLECTOMETER TESTING ...............................................2 3.2 PAVEMENT CORE HOLES ...............................................................................3 3.3 LABORATORY TESTING .................................................................................3 4.0 SITE CONDITIONS ......................................................................................................4 4.1 SITE DESCRIPTION.........................................................................................4 4.2 GENERAL GEOLOGY ......................................................................................4 4.3 PAVEMENT STRUCTURAL
    [Show full text]
  • Core Bits Are Classifi Ed According Figure 1
    OCEAN DRILLING PROGRAM www.oceandrilling.org Scientifi c Application Extended Core Barrel (XCB) (see the XCB tool sheet) (both sys- A core bit (Figs. 1, 2) is a drilling Cutting shoe tems use the same BHA), tool with a hole through the center that removes sediment rock and II. Rotary Core Barrel (RCB) (see allows the core pedestal to pass the RCB tool sheet), and through the bit and into the core III. Advanced Diamond Core Barrel barrel. The Ocean Drilling Program (ADCB) (see the ADCB tool (ODP) employs different coring sheet). systems and bits to obtain continu- ous cores in all types of oceanic Bottom-Hole Assembly sediments and igneous basement. Operation The BHA for each coring system Once a coring system is selected is slightly different, but in gen- based on the expected lithology, eral consists of a primary core bit, the engineer determines which outer core barrel (OCB), short type of core bit to use. As coring sub assembly, and drill collars. conditions change, the coring bit The OCB supports the wireline A can be changed in an attempt retrievable inner core barrel, which to improve the recovery and rate Cutting shoe receives and carries the core. Drill of penetration with that coring collars are heavyweight pipes that system. The type of bit used apply weight to the bit on the depends on the expected lithology bottom of the OCB. The BHA is and past bit performance in the run on the drill pipe string, which area or in a similar lithology. Once is rotated at the surface to drive a bit is removed, it is “graded” the bit (except the Motor-Driven (i.e., it is examined to determine Core Barrel [MDCB]) and advance wear on the cutting structure, the BHA (see the BHA tool sheet gauge, bearings, etc., based on for more information).
    [Show full text]
  • Core Drilling of Hot Mix Asphalt (HMA) for Specimens of 4” Or 6” Diameter
    Proposed method and procedure Core Drilling of Hot Mix Asphalt (HMA) for Specimens of 4” or 6” diameter 1. SCOPE 1.1 This method is to establish a consistent method of the use of a diamond bit core to recover specimens of 4 or 6 inch diameter for laboratory analysis and testing. 1.2 The method will require the use of: water, ice (bagged or other suitable type), dry ice, and a water-soap solution to be utilized when coring asphalt rubber concrete. 1.3 Individuals doing the specimen recovery should be observing all safety regulations from the equipment manufacturer as well as the required job site safety requirements for actions, and required personal protective equipment. 2. CORE DRILLING DEVICE 2.1 The core drilling device will be powered by an electrical motor, or by an acceptable gasoline engine. Either device used shall be capable of applying enough effective rotational velocity to secure a drilled specimen. The specimen shall be cored perpendicularly to the surface of pavement, and that the sides of the core are cut in a manner to minimize sample distortion or damage. 2.2 The machinery utilized for the procedure shall be on a mounted base, have a geared column and carriage that will permit the application of variable pressure to the core head and carriage throughout the entire drilling operation. The carriage and column apparatus shall be securely attached to the base of the apparatus; and the base will be secured with a mechanical fastener or held in place by the body weight of the operator.
    [Show full text]
  • Core Drill Core Drill
    DRILLING until the core bit has stopped rotating. Keep the equipment clean - you will find this less of a 309/01 For standard drilling (without dust removal fitted) use Remove the hole-starting aid from the core bit if it was chore if you clean it regularly, rather than wait until the end slotted core bits. fitted before. of the hire period. NOTE: Dust is released in all directions. Drilling Position the core bit (in the guide kerf when the hole- Keep cutting tools sharp and clean. Properly maintained Operating & Safety Guide 309 without a dust removal system, especially overhead starting aid was used) and then press the on / off switch to cutting tools with sharp cutting edges are less likely to bind drilling, is very unpleasant and optimum performance continue drilling. and are easier to control. is not achieved. Overhead drilling without use of dust Allow the vacuum cleaner to run for a few seconds When not in use, store the equipment in its toolbox removal system is therefore not recommended. For dry after switching off the machine in order to ensure that the somewhere clean, dry and secure. coring it is recommended that the dust removal remaining dust is removed. attachment and a suitable vacuum cleaner are always Professional dust removal equipment available for used. from HSS Hire. FINISHING OFF Release the on / off switch on the power tool and slowly DANGER! NOISE AND VIBRATION pull the core bit out of the hole. Switch off the vacuum cleaner if you are using one. HOLD POWER TOOL BY INSULATED GRIPPING SURFACES, Typical A-weighted sound power level: 95 dB (A) WHEN PERFORMING AN OPERATION WHERE THE Switch OFF power supply before unplugging it.
    [Show full text]
  • 204-5 Asphalt Concrete Samples Obtained by Coring
    STP 204-5 Standard Test Section: ASPHALT MIXES Procedures Manual Subject: ASPHALT CONCRETE SAMPLES OBTAINED BY CORING 1. SCOPE 1.1. Description of Test The standard test procedure is used for collecting samples of asphalt concrete by coring methods. 1.2. Application of Test Samples of asphalt concrete collected using the coring method may be used to evaluate various characteristics of an asphalt concrete pavement for construction quality control testing, quality assurance testing and product acceptance testing. Core samples may also be used for research testing purposes. 1.3. Units of Measure The standard core sample diameter for purposes of this test procedure will be 101.6 mm or 152.4 mm. Generally, the maximum thickness of asphalt concrete pavement to be sampled will be 250 mm. 2. APPARATUS AND MATERIALS 2.1. Equipment Portable Drilling Equipment - mounted on a trailer, truck or other similar equipment for transportation purposes. The drill shall be equipped with a source of power suitable for driving the core barrel. The drilling unit will be equipped with a source of air or water supply to cool the core barrel during drilling operations. Core Barrels - which will provide cores as described in section 1.3. Generally thin walled core barrels with surface set diamond cutting edges provide the best samples. Core Retrieval Tool - to extricate cores from the pavement when coring is completed, without causing damage to the cores. Marshall hand held compaction hammer. Gloves or mitts for handling dry ice. Date: 1994 12 09 Page 1 of 6 Standard Test Procedures Manual STP 204-5 Section: Subject: ASPHALT MIXES ASPHALT CONCRETE SAMPLES OBTAINED BY CORING An insulated container in which cores can be placed and maintained at a cold temperature.
    [Show full text]
  • Drilling Manual Jn Dunster
    NORTHERN TERRITORY GEOLOGICAL SURVEY DRILLING MANUAL JN DUNSTER Record 2004-007 Northern Territory Government Department of Business, Industry & Resource Development NORTHERN TERRITORY DEPARTMENT OF BUSINESS, INDUSTRY AND RESOURCE DEVELOPMENT Geological Survey Record 2004-007 Drilling manual JN Dunster Northern Territory Geological Survey Northern Territory Government Darwin, 2004 Department of Business, Industry & Resource Development i DEPARTMENT OF BUSINESS, INDUSTRY AND RESOURCE DEVELOPMENT MINISTER: Hon Kon Vatskalis, MLA CHIEF EXECUTIVE OFFICER: Mike Burgess NORTHERN TERRITORY GEOLOGICAL SURVEY DIRECTOR: Richard Brescianini BIBLIOGRAPHIC REFERENCE: Dunster JN, 2004. Drilling manual. Northern Territory Geological Survey, Record 2004-007. (Record / Northern Territory Geological Survey ISSN 1443-1149) Bibliography ISBN 0 7245 7085 3 Keywords: Drilling, core drilling, diamond drilling, drilling problems, RC drilling, slim hole drilling, stratigraphic drilling, wire line drilling, drilling equipment, drilling fluids EDITORS: PD Kruse and TJ Munson For further information contact: Geoscience Information Northern Territory Geological Survey GPO Box 3000 Darwin NT 0801 Phone: +61 8 8999 6443 Website: http://www.minerals.nt.gov.au/ntgs © Northern Territory Government 2004 Disclaimer While all care has been taken to ensure that information contained in Northern Territory Geological Survey, Record 2004-007 is true and correct at the time of publication, changes in circumstances after the time of publication may impact on the accuracy of its information. The Northern Territory of Australia gives no warranty or assurance, and makes no representation as to the accuracy of any information or advice contained in Northern Territory Geological Survey, Record 2004-007, or that it is suitable for your intended use. You should not rely upon information in this publication for the purpose of making any serious business or investment decisions without obtaining independent and/or professional advice in relation to your particular situation.
    [Show full text]
  • Diamond Core Drill User Guide View File
    User Guide Please observe the following guidelines to ensure a long working life for your Faithfull Diamond Core Bits. Faithfull Diamond Dry Core Bits are suitable for Always ensure that the core bit is rotating when cutting breeze block, brick and soft concrete. entering and exiting the material being cut. They are not designed to cut extremely dense use “hammer” action when using a diamond concrete, engineering bricks or abrasive materials Never core bit, as this is likely to cause damage to both because doing so may damage or reduce the the core drill bit and to your power tool. working life of the core bit. attempt to cut metal or reinforced concrete Diamond Core Bits must always be used with power Never as damage to the core bit is likely to occur. drills rated at between 850 to 1,000 watts, which are equipped with a safety clutch and a variable speed Never allow the core bit to become excessively hot function capable of speeds of up to 3000 rpm. while cutting, and allow a cooling down time Always use the drill at the recommended rotational between cutting applications. speed for the size of core bit being used. Please refer to your manufacturers’ instructions as Speeds of between 1,000 and 3,000 rpm are normal to the maximum core diameter that can be safely for the correct operation of diamond core bits. used with your power tool. ROTARY USE ONLY – Must not be used on Percussion/Hammer mode DO NOT use Diamond Cores larger than 78mm in diameter Operation Hints with SDS-plus drills as this may result in damage to the power tool or SDS adaptor.
    [Show full text]
  • LIGHTWEIGHT 50-METER CORE DRILL for FIRN and ICE Heinrich
    Reproduced from Ice-Core Drilling edited by John F. Splettstoesser by permission of the University of Nebraska Press. Copyright 1976 by the University of Nebraska Press. Copyright renewed 2004 by the University of Nebraska Press. LIGHTWEIGHT 50-METER CORE DRILL FOR FIRN AND ICE Heinrich Rufli, Bernhard Stauffer, and Hans Oeschger Physics Institute University of Bern Sidlerstrasse 5 3012 Bern, Switzerland ABSTRACT The increasing interest in ice-core analyses has made it apparent that new drills need to be developed for coring in Jim and ice. To close the gap between the range of the SJPRE coring auger and that of the CRREL thermal drill an electromechanical drill has been constmcted which will core to 50 m in fim and ice. The drill is suspended from a cable, and consists of a coring system, a driving system and an antitorque system. The drill was tested successfully in Greenland in 1974, where it was possible to drill to 50 m in a few hours. In troduction With the SIPRE coring auger it is relatively easy to drill to 20 m in fim or 10m in ice. Drilling deeper is possible but difficult. Holes with depths between 100 and 500 m have usually been made using thermal drills (Ueda and Garfield, 1969). Attempts have been made to close the gap between the ranges of the two drills by mOdify­ ing the SIPRE coring auger. The modifications consist of an electrical drive for drilling and electrical and mechanical means for raising and lowering the auger. They allow deeper drilling but the equipment is heavier and the drilling is tin,e-consuming because of the need to handle the numerous extensions.
    [Show full text]
  • Development of Smart Boulders to Monitor Mass Movements Via the Internet of Things: a Pilot Study in Nepal Abstract
    https://doi.org/10.5194/esurf-2020-78 Preprint. Discussion started: 8 October 2020 c Author(s) 2020. CC BY 4.0 License. Development of smart boulders to monitor mass movements via the Internet of Things: A pilot study in Nepal Benedetta Dini1, Georgina L. Bennett2, Aldina M. A. Franco1, Michael R. Z. Whitworth3, Kristen L. Cook4, Andreas Senn5, John M. Reynolds6 1 School of Environmental Sciences, University of East Anglia, Norwich Research Park, UK; 2College of Life and Environmental Sciences, University of Exeter, UK; 3AECOM, UK; 4GFZ-Potsdam, Germany; 5Miromico AG, Zurich, Switzerland; 6Reynolds International Ltd, UK 1 Abstract 2 Boulder movement can be observed not only in rock fall activity, but also in association with other 3 landslide types such as rock slides, soil slides in colluvium originated from previous rock slides and 4 debris flows. Large boulders pose a direct threat to life and key infrastructure, amplifying landslide 5 and flood hazards, as they move from the slopes to the river network. Despite the hazard they pose, 6 boulders have not been directly targeted as a mean to detect landslide movement or used in dedicated 7 early warning systems. We use an innovative monitoring system to observe boulder movement 8 occurring in different geomorphological settings, before reaching the river system. Our study focuses 9 on an area in the upper Bhote Koshi catchment northeast of Kathmandu, where the Araniko highway 10 is subjected to periodic landsliding and floods during the monsoons and was heavily affected by 11 coseismic landslides during the 2015 Gorkha earthquake. In the area, damage by boulders to 12 properties, roads and other key infrastructure, such as hydropower plants, is observed every year.
    [Show full text]
  • Geotechnical Characterisation of Landslide Slope-Prone Sediments
    Geotechnical measurements to characterise slope sediments and to identify landslide mechanisms and their impact on ecosystems Doctoral Thesis submitted for the doctoral degree in natural sciences at the Faculty of Geosciences of Bremen University zur Erlangung des Doktorgrades der Naturwissenschaften im Fachbereich Geowissenschaften der Universität Bremen by vorgelegt von Annika Förster Bremen, Juni 2011 Tag des Kolloquiums: 31. Oktober 2011 Gutachter: Prof. Dr. Achim J. Kopf Prof. Dr. Tobias Mörz Prüfer: Prof. Dr. Katrin Huhn Prof. Dr. Rüdiger Henrich Abstract 1 Abstract Submarine mass wasting processes are not uniformly distributed over the world’s ocean. Glaciated margins are also affected as non-glaciated margins including fjords, submarine canyons and river deltas. Observation, monitoring and analysis of the mass wasting processes are of large scientific as well as socio-economic interest due to the hazardous impact of, e.g. landslides on offshore industry installations. Likewise, Tsunamis that are triggered by mass wasting processes, endanger coastal cities and surrounding areas. The distribution of submarine landslides may be controlled by the interaction of morphology, sediment composition, sediment mechanical behaviour (e.g. lowered sediment strength) and external triggers (e.g. earthquakes, sea-level change). In summary, the presented study investigates the mechanics, mechanisms and factors governing slope instabilities of three different submarine landslides sites evolved from active and passive continental margins. Results of geotechnical measurements from both the stable and the failed part of the different landslides were compared to previously published geophysical and sedimentological data. The three different research sites are i) the passive continental margin of Mauritania, NW-Africa, ii) the low seimic and tectonically active Ligurian margin (Southern France) and iii) the high tectonically active margin of the Cretan Sea (Greece).
    [Show full text]