Operating Manual Dometic RM2351, RM2354, RM2451, RM2454

OPERATING INSTRUCTIONS RM2351 RM2454 DM2652 DM2852 RM2354 RM2551 DM2662 DM2862 RM2451 RM2554 DM2663 NDM1062

FIRE OR EXPLOSION HAZARD If you smell gas: 4. Extinguish any open flame. 1. Open windows. 5. Shut off fuel supply. 2. Do not attempt to light appliance. 6. Evacuate immediately and call 3. Do not touch electrical switches. emergency services. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

If the refrigerator stops cooling - or - if it emits an ammonia smell, immediately turn the refrigerator off and contact a Service Center.

REVISION D USA & CANADA SERVICE CENTER & Form No. 3313240.016 12/17 SERVICE OFFICE DEALER LOCATIONS (French 3313241.013_D) Dometic Corporation Please Visit: ©2017 Dometic Corporation 1120 North Main Street www.dometic.com LaGrange, IN 46761 Elkhart, IN 46514 INTRODUCTION Thank you for purchasing a new Dometic refrigerator. This product is a recreational vehicle refrigerator intended for the storage of fresh and frozen foods, as well as making ice. Appearance of your product may vary from illustrations shown in this document. Please read and be aware of possible safety hazards identified in this manual, and become familiar with the alert symbols on the refrigerator. Read this manual carefully so that you know how to operate the refrigerator safely and correctly. Keep this manual with the refrigerator for future reference. CONTENTS REFRIGERATOR OVERVIEW...... 3 INSTRUCTIONS FOR USE...... 6 STORAGE COMPARTMENTS...... 9 PRODUCT CARE...... 10 MAINTENANCE & SERVICE ...... 12 TROUBLESHOOTING ...... 14 APPENDIX A - SPARE PARTS...... 15 APPENDIX B - REARVIEW EQUIPMENT ...... 17 APPENDIX C - WIRING DIAGRAM ...... 19 APPENDIX D - CONSUMER SUPPORT ...... 24 APPENDIX E - DOMETIC WARRANTY...... 25 APPENDIX F - MAINTENANCE SCHEDULE...... 26

SYMBOLS The following symbols are used throughout this manual:

This is the safety alert symbol. It is used to alert you to personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

Information

Step-by-step instructions

2 REFRIGERATOR OVERVIEW ABSORPTION COOLING SYSTEM WHEN THE REFRIGERATOR IS NOT When turning on the refrigerator, you should ad- IN USE just the thermostat (excludes RM2351, RM2451, Any absorption refrigerator that is to be taken out of ser- RM2551, DM2652 & DM2852 - not adjustable) to vice for an extended period of time should be turned off. the coldest temperature setting. The cooling cycle may require an extended running time before cool- It is important that you do not leave the refrigerator ing effect is observed. to run idle and/or unattended for days or weeks.

LEVELING THE REFRIGERATOR Leveling is one of the requirements for proper operation AUTOMATIC ENERGY SELECTOR with absorption refrigerators. To ensure proper leveling the SYSTEM vehicle needs to be leveled so it is comfortable to live in The refrigerator is equipped with an automatic energy se- (no noticeable sloping of floor or walls). lector system. The user turns the refrigerator on and then, Any time the vehicle is parked for several hours with the the refrigerator automatically selects the most suitable en- refrigerator operating, the vehicle should be leveled to al- ergy source available, either 120 VAC or LP gas operation. low proper cooling. The system can be set by the user to be fully automatic When the vehicle is moving, the leveling is not critical, as (AUTO mode is selected) or to operate on LP gas only (AUTO mode is off). the rolling and pitching movement of the vehicle will pass to either side of level, keeping the liquid ammonia from On 3-way models, the control system can manually be set accumulating in the evaporator tubing. to DC mode (DC operation). The DC mode overrides all other operating modes. OPERATING REFRIGERATOR AT HIGH The refrigerator controls will work down to 9.6 VDC. ALTITUDE All gas appliances experience lowered efficiency (or rat- ing) at high altitude This is a direct result of lower atmos- pheric pressure and oxygen levels, and is not a defect of the refrigerator. Reduced cooling performance and burner outage may occur at altitudes higher than 5500 feet above sea level (while operating on LP gas). Always operate refrigerator on electric power at altitudes higher than 5500 feet.

PURGING AIR FROM THE LINES If the refrigerator has not been used for a long time - or - the LP tanks have just been refilled, air may be trapped in the supply lines. To purge the air from the lines, turn the refrigerator off and on by pressing the ON/OFF button. If the flame is not lit within 45 seconds, turn the refrigerator off and back on again. This procedure can be repeated 3 to 4 times. If repeated attempts fail to start the LP gas operation, check to make sure that the LP gas supply tanks are not empty and that all manual shutoff valves in the lines are open. If the problem persists, turn the refrigerator off and take it to a Service Center.

3 REFRIGERATOR OVERVIEW CONTROL PANEL RM2351, RM2451, RM2551, DM2652 & DM2852 1. ON/OFF button (main power) A B 2. AUTO/GAS mode selector button

A. AUTO mode indicator lamp ON AUTO CHECK indicator lamp 1 2 AUTOMATIC REFRIGERATOR TEMPERATURE CONTROL B. CHECK OFF GAS (GAS mode only)

RM2354, RM2454, RM2554 & DM2663 1. ON/OFF button (main power) 2. DC mode selector button A D E 3. AUTO/GAS mode selector button

ON DC AUTO COLD 1 2 3 4 5 COLDEST 4. Temperature selector button 1 2 3 4 mode indicator lamp OFF AC GAS CHECK A. DC B. AC mode indicator lamp C. GAS mode indicator lamp B C F D. AUTO mode indicator lamp E. CHECK indicator lamp (GAS mode only) F. Temperature indicator lamps

DM2662, DM2862 & NDM1062 1. ON/OFF button (main power) 2. AUTO/GAS mode selector A D button 3. Temperature selector button

ON AUTO COLD 1 2 3 4 5 COLDEST A. AUTO mode indicator lamp 1 2 3 B. AC mode indicator lamp OFF AC GAS CHECK C. GAS mode indicator lamp D. CHECK indicator lamp indicator lamps B C E E. Temperature NDM1062 1. ON/OFF button (main power) 2. AES/AUTO/GAS mode B D selector button 3. Temperature selector button AES ON AUTO COLD 1 2 3 4 5 COLDEST CLC LAC 4. Climate control button 1 2 3 4 5 OFF AC GAS CHECK 5. Low ambient control button

A C E F G A. AC mode indicator lamp B. AES/AUTO mode indicator lamp C. GAS mode indicator lamp D. CHECK indicator lamp E. Temperature indicator lamps F. Climate control indicator lamp G. Low ambient control indicator lamp 4 REFRIGERATOR OVERVIEW MODES OF OPERATION LIMP MODE OF OPERATION AUTO MODE - AES/AUTO MODE In the event of a failure of a major operating component, the control system will continue to operate the cooling When operating in AUTO - AES/AUTO mode, the AUTO system. - AES/AUTO mode indicator lamp is illuminated. The control system will automatically select between AC and GAS RM2351, RM2451, RM2551, DM2652 & DM2852 operation. AC has priority over GAS. Should AC become unavailable, the system automatically switches to GAS. If the control can not read the temperature sensor and As soon as AC becomes available again, the control will control the preset temperature, the control will run the switch back to AC regardless of the status of the GAS cooling unit continuously at the energy source available. operation. The refrigerator will continue to operate in this mode in- If the CHECK indicator lamp is illuminated the controls definitely - or - until a new sensor is installed and the sys- have failed to ignite the burner in the GAS mode. To re- tem reset. start an ignition attempt with the CHECK lamp illuminated (or to turn off the CHECK lamp), press the ON/OFF button RM2354, RM2454, RM2554, DM2662, DM2663, DM2862 & OFF and back ON again. The control system activates NDM1062 the ignition system and makes three attempts to light the Two modes of operation can occur: burner for a period of approximately 45 seconds at two 1) The first limp mode of operation will execute if the minutes interval. Should 120 VAC become available while display module becomes non functional. The control the CHECK indicator lamp is on, the CHECK lamp will not system reverts to full automatic operation selecting turn off until the ON/OFF button is pressed OFF and then the best energy source available with AC, DC (3- ON again. way only) and GAS priority. The temperature setting GAS MODE is maintained at the mid position. The power module will continually attempt to reestablish operation of the RM2351, RM2451, RM2551, DM2652 & DM2852: display module. When operating in GAS mode, the AUTO mode indicator 2) The second limp mode of operation will execute when lamp will be off. a failure of the temperature sensing device or associ- RM2354, RM2454, RM2554, DM2662, DM2663, DM2862 & ated electronic circuitry occurs. If this should happen, NDM1062: When operating in GAS mode, the GAS Mode the control system operates on the energy source se- indictor lamp is illuminated. lected via the control panel. The cooling unit runs con- This mode provides LP gas only. The control system acti- tinuously on the selected energy source. The refrig- vates the ignition system and attempts to light the burner erator continues to operate in this mode indefinitely or for a period of approximately 45 seconds at two minutes until a new sensor is installed and the system is reset. interval. If unsuccessful, the CHECK indicator lamp will illuminate. To restart GAS operation, press the ON/OFF button to OFF and then back ON. The control system attempts a new ignition sequence. DC MODE RM2354, RM2454, RM2554 & DM2663 When operating in DC mode (3-way models only), the DC mode indicator lamp is illuminated and all other lamps are off. To select another operating mode, turn off the DC mode by pressing the DC selector button. The DC lamp is turned off. When there is no charging of the house battery, switch to AUTO mode or GAS mode since running the refrigerator on 12 VDC will quickly drain the battery.

5 INSTRUCTIONS FOR USE STARTING THE REFRIGERATOR --DC mode (3-way models only) Press the DC mode indicator button. The DC lamp will be turned on. To select AUTO or GAS FIRE HAZARD. When the RV has not been mode, turn off the DC mode by pressing the DC mode selector button. The DC lamp will used for some time, make sure that the path then be turned off. between the burner jet and the burner tube has not been obstructed before lighting the ADJUSTING THE THERMOSTAT LP gas burner. Failure to obey this warning RM2354, RM2454, RM2554, DM2662, DM2663, DM2862 could cause a fire resulting in death or seri- & NDM1062 ous injury. The thermostat controls both the gas and electric operation, thereby eliminating the necessity of resetting each time a different energy source is employed. After the initial start-up, the thermostat should be adjusted to the desired FIRE OR EXPLOSION HAZARD. When refuel- temperature setting. 1. Press the temperature selector button until the ing or parked near gasoline pumps shut off all lamp at the desired setting is illuminated. LP gas appliances. Failure to obey this warn- RM2351, RM2451, RM2551, DM2652 & DM2852 ing could cause a fire or explosion resulting The temperature is controlled by a factory preset temper- in death or serious injury ature setting.

LP GAS EQUIPMENT ASSEMBLY COLD WEATHER LOW AMBIENT SOLENOID VALVE CONTROL BURNER MOUNTING SCREWS NDM1062 The refrigerator is equipped with an exclusive feature that

INLET FITTING allows for trouble-free operation in low ambient temperature (like below 50°F) for extended periods of time. Once the outdoor temperature is above 50°F, the low ambient MANUAL SHUTOFF VALVE switch should be turned off. Shown in open position BURNER TUBE 1. Turn the Low ambient control switch to I (ON). BURNER JET PRESSURE TEST PORT SPARK ELECTRODE

1. Check that all the manual gas valves are in the The Low ambient control ON position. switch is located beneath the top decoration panel 2. Make sure that a continuous 12 VDC supply is that houses the control available for the electronic control to function. panel. 3. Press the ON/OFF button. 4. Select operation mode: 2. Press the LAC button. The indicator lamp will illuminate. --AUTO - AES/AUTO mode (AC and Gas) Press the AUTO/GAS - AES/AUTO/Gas mode AES selector button (if not already on). The illumi- ON AUTO COLD 1 2 3 4 5 COLDEST CLC LAC OFF AC GAS CHECK nated lamp indicates the selected mode. (If the CHECK indicator lamp is illuminated, see REFRIGERATOR OVERVIEW > MODES OF OPERATION > AUTO MODE - AES/AUTO MODE for further information.) --GAS mode (LP gas operation only) Press the AUTO/GAS - AES/AUTO/Gas mode selector button to turn off the AUTO mode (if not already off). (Within 45 seconds the burner should be ig- nited and operating normally. If not, see RE- FRIGERATOR OVERVIEW > MODES OF OPERATION > GAS MODE for further information.) 6 INSTRUCTIONS FOR USE EXTREME COLD WEATHER OPERATING THE ICE MAKER OPERATION (ICE MAKER MODELS ONLY) Refrigerator performance may be reduced in extremely Before the ice maker can operate, make sure that: cold (subzero) temperatures. This temporary condition is • The refrigerator is connected to 120 VAC . normal for absorption refrigerators and does not indicate • The water valve supplying the refrigerator is turned on. product failure. In the event that performance is reduced • The ice level bail arm is in its fully down position. in such conditions, turn the refrigerator off. As ambient Keep bail arm in the up (OFF) posi- temperatures rise, please restart your refrigerator accord- tion until water is present at the ice maker. ing to instructions before requesting service.  Ice level CLIMATE CONTROL SYSTEM bail arm NDM1062 During the summer months of high temperature and humidity, the metal frame between the freezer and fresh food compartments may have water droplets forming. The number of water droplets will increase if the vehicle is not air Down conditioned during these months. The refrigerator comes position standard with a 12 VDC climate control that will evaporate the water droplets when they form. The climate control can When the ice maker thermostat senses the preset temperature for the ejection of the ice cubes, the fingers will start to be left on continuously or used only when temperatures rotate, dumping any ice cubes and filling the mold with water. require it. Note that when turned on, the climate control When the storage container is full, the bail arm will come will draw 12 VDC power continuously. Turn it off when a in contact with the ice cubes. The bail arm cannot return charging source is not available. to the full down position and the ice production is stopped 1. Turn the climate control switch to I (ON). until the bin is emptied, or ice cubes are removed.

To prevent water from splashing out of the mold assembly The Climate control while travelling in your recreational vehicle, raise the bail switch is located be- arm to the full UP/OFF position about 1-1/2 hours before neath the top decora- departing. This will allow the water in the mold to freeze. tion panel that houses the control panel. WATER SUPPLY The water supply system must have a minimum pressure of 15 pounds per square inch gauge (psig). A 1/4” diame- 2. Press the CLC button. The indicator lamp will ter water line to the water valve should be used at the rear illuminate. of the refrigerator. The water line must have a manual shutoff valve placed where it is easily accessible.

AES The maximum water level is represented by a thin line. It ON AUTO COLD 1 2 3 4 5 COLDEST CLC LAC

OFF AC GAS CHECK is essential that the water level does not exceed this line!

Maximum water level

If necessary,change the water flow by adjusting the water supply. For instructions, see ADJUSTING THE SIZE OF CUBES. 7 INSTRUCTIONS FOR USE ADJUSTING THE SIZE OF CUBES 3. Turn the screw clockwise to decrease the cube If the ice maker was cleaned and drained, no ice size or if the mold is overfilling, and the cubes are stuck together. cubes will be dumped into the bin during the first To prevent overfilling, do not turn the adjustment cycle. The first few cycles may have small cubes due toair screw more than one revolution at a time. Allow trapped in the water lines. The first container of ice cubes the ice maker to cycle several times before another should be dumped if the water system has been winter- adjustment is made. Be sure to replace the protec- ized or not used for several weeks. Once the ice mak- tive cover on the cycle after the adjustments are er has run through several cycles and if cubes are too complete. small or sticking together, adjustment is necessary on the amount of water entering the mold. TURNING OFF THE REFRIGERATOR, AND WHEN NOT IN USE TO ADJUST THE SIZE OF CUBES, FOLLOW THESE You can turn off your refrigerator by pressing the main STEPS: power ON/OFF button found on the control panel to the 1. Remove the protective cover from the ice mak- OFF position. This will shut off all power to the refrigerator, er mechanism. Using a flat-head screwdriver, including DC power to the refrigerator. place the tip of the screwdriver in the slot. Twist If the refrigerator will not be in operation for an extended the screwdriver blade gently to loosen the cover. period of time or put into winter storage it should be emptied, defrosted, cleaned, and the doors placed in the airing position. If ice cube trays are in use, they should also be dried and kept outside the cabinet.

This refrigerator is intended for continuous use. Do not allow it to run unattended when there is a risk for loss of electricity or fuel. Food spoilage could occur.

The refrigerator’s control system still consumes a few milliamps even if it is turned off. If your RV is being put into winter storage, it is recommended to either put your RV batteries on a battery charger or turn off the vehicle’s main 12 VDC switch. This will prevent the RV battery from discharging.

2. Locate the adjusting screw under the protective cover. Turn the screw counterclockwise to increase the size of cubes.

Adjusting screw

Cover

8 STORAGE COMPARTMENTS FROZEN FOOD STORAGE FIRE OR EXPLOSION HAZARD. Do not store COMPARTMENT or use gasoline, oil or gasoline soaked rags, This compartment is not designed for deep or quick freez- or other flammable vapors and liquids in the ing of food. service area behind the refrigerator or in the • To prevent food from drying out, keep it in covered vicinity of this or any other gas appliance. dishes, containers, plastic bags or wrapped in aluminum foil. Failure to obey this warning could cause a • Meat or fish, whether raw or prepared, can be stored in fire or an explosion resulting in death or seri- the frozen food storage compartment provided they are ous injury. precooled first in the refrigerator. They can be stored about three times longer in the frozen food compartment as compared to the fresh food compartment. REFRIGERATOR VOLUME • Quick frozen soft fruits and ice cream should be placed MODEL TOTAL REFRIGERATED in the coldest part of the compartment, which is at the bottom of the aluminum liner. VOLUME (CU. FT.) • Frozen vegetables, may be stored in any part of the RM2351& RM2354 3 compartment. RM2451& RM2454 4 • To prevent frost buildup, which can reduce the efficiency, wipe excess moisture off items being placed in the RM2551 & RM2554 5 compartment. DM2652, DM2662 & DM2663 6 DM2852 & DM2862 8 REMOVING AND REPLACING THE NDM1062 9.2 SHELVES 1. Remove the shelf locks by inserting the tip of a flat bladed screwdriver into the slot of the locks. FOOD STORAGE COMPARTMENT Turn the screwdriver counterclockwise and then • Cool the refrigerator before placing any food inside. remove the shelf locks from the wire shelf. Never put hot food or drinks into the refrigerator - cool them first. • The food storage compartment is completely closed and unventilated, which is necessary to maintain the required low temperature for food storage. Consequently, foods having a strong odor or those that absorb odors easily should be covered. • Vegetables, salads, etc. should be covered to retain their crispness. 2. Slide the shelf to the left until bushings disen- • The coldest positions in the refrigerator are under the gage, then tilt the shelf to one side at an angle cooling fins and at the bottom of the refrigerator. The while pulling forward. warmer areas are on the upper door shelves. This should be considered when placing different types of food in the refrigerator. • Arrange all food in the unit to allow for free air circulation. Do not overpack because a stuffed refrigerator must work harder and will have higher cabinet temperatures. • Do not leave the unit’s door open any longer than nec- 3. Reposition the shelf in the desired location. In- essary. This will reduce frost formation and increase the sert the ends of the wire shelf on the left-hand efficiency of the refrigerator. side and slide the shelf into the holes on the right-hand side. 4. Slide the plastic plugs into the holes of the wall. 5. Snap the shelf locks back onto the wire shelf.

9 STORAGE COMPARTMENTS ICE CUBES RM2351, RM2454, RM2554, DM2662, DM2663, DM2862 & NDM1062 Ice cubes can be made in the freezer compartment. For Ice will be made more rapidly if the thermostat is set at its faster freezing, place trays in direct contact with the bottom highest position, but be sure to move the thermostat back of the freezer compartment. to normal setting when ice is formed; the refrigerator might otherwise become too cold.

PRODUCT CARE DEFROSTING AIRING POSITION 1. Shut off the refrigerator by pressing the main power ON/OFF button (OFF position). DM2652, DM2662, DM2663, DM2852 & 2. Empty the refrigerator. DM2862 3. Leave the cabinet and freezer doors open and make sure the drip tray is in place under the finned evaporator. Use the airing position card Defrosting time can be reduced by filling ice trays to keep the doors ajar if the with hot water and placing them in the freezer com- refrigerator is put in storage partment. or will not be used for an extended period of time.

FIRE AND INHALATION HAZARD. Do not use 2 a knife, ice pick, or any other sharp tool to 1 remove frost from the freezer compartment. Failure to obey this warning could cause a leak in the ammonia cooling system which could lead to a fire hazard resulting in death or serious injury. An ammonia leak also poses an inhalation hazard, and could cause chemical burns to the skin and eyes. Exposure to a high concentration of ammonia could result in death 3 4 5 or serious injury.

Do not use a hot air blower to remove frost from the freezer compartment. Permanent damage could result from warping the metal or plastic parts. 4. When all the frost has melted, dry the interior with a clean cloth and turn the refrigerator back on. RM2354, RM2454, RM2554, DM2662, DM2663, DM2862 & NDM1062 5. Set the thermostat to the coldest setting for a few hours. Then, reset the thermostat to the desired setting, usually at mid setting. Replace food after refrigerator has reached appropriate cool temperature.

10 PRODUCT CARE CLEANING STORAGE PROCEDURE/WINTERIZ- Always keep the refrigerator clean. Cleaning the refrigera- ING THE REFRIGERATOR tor is usually done after it is defrosted or put into storage. Use a lukewarm, weak soda solution to clean the interior (ICE MAKER MODELS ONLY) liner of the refrigerator. Use warm water only to clean the The refrigerator is equipped with a heater tape wrapped finned evaporator, gasket, and shelves. Do not spray liq- around the water solenoid valve and outlet water tube. uids near electrical outlets, connections, or the refrigerator During cold weather operation below 32°F/0°C the au- components. tomatic temperature switch will turn the heater tape on After cleaning the interior liner/evaporator fins, make sure automatically. thermistor bulb and thermistor bracket are properly posi- tioned. See “Troubleshooting” on page 14. If the RV will not be in use for an extended period of time or put into storage: • Drain the RV water system. Do not use strong chemicals or abrasives to • Disconnect the water lines from the inlet and outlet clean these parts, as the protective surfaces sides of the water valve. Drain the lines into a cup and will be damaged. allow the lines to dry. To keep the refrigerator operating efficiently, periodic in- • The ice maker should be drained and dried. Note that spection and cleaning of several components once a year this procedure must be performed by a qualified ser- is recommended: vice technician. • Check the lower vent, upper vent and area between • Using a lukewarm soda solution, clean the interior these openings for any obstructions such as bird/insect liner of the refrigerator. Clean the finned evaporator nests, spider webs, etc. and shelves. Use warm water only and never strong chemicals or abrasives since these can damage the • Make sure the refrigerator area is free from combusti- protective surfaces. ble material, gasoline and other flammable vapors or liquids. • Place doors in the airing position.

FIRE OR EXPLOSION HAZARD. Do not store or use gasoline, oil or gasoline soaked rags, or other flammable vapors and liquids in the service area behind the refrigerator or in the vicinity of this or any other gas appliance. Failure to obey this warning could cause a fire or an explosion resulting in death or serious injury.

• If accessible, clean the coils on the back of the refrigerator. Use a soft bristled brush to dust off the coils.

11 MAINTENANCE & SERVICE To keep the refrigerator working properly, a quali- 3. Replace the fuse. fied service technician should, at least once a year, inspect the connections, the control system, the LP gas pressure and flue baffle.

FIRE AND INHALATION HAZARD. If the re- 4. Put the holder back together. frigerator stops working -or- if it emits an ammonia smell, immediately turn the refrigerator off, leave the vicinity, and contact a Service Center. A high concentration of ammonia refriger- ant could cause an inhalation hazard, could PERIODIC MAINTENANCE cause chemical burns to the skin and eyes, To be performed by a qualified service technician and could cause a fire resulting in death or only. serious injury. CHECKING THE LP GAS CONNECTIONS REPLACING THE FUSES 1. Check all connections in the LP gas system (at 2-way models are equipped with 2 fuses - one for the the back of the refrigerator) for gas leaks. The refrigerator control system and one for the AC heater. LP gas supply must be turned on. 3-way models are equipped with 3 fuses - two fuses in 2. Apply an approved leak detection solution to all the power module and one in-line blade fuse. LP gas connections. The appearance of bub- bles indicates a leak and should be repaired im- Control system 3 A mediately! AC heater 5 A 12 VDC heater 30 A FIRE OR EXPLOSION HAZARD. Never use an open flame to check for gas leaks. Failure to REPLACING THE FUSES obey this warning could cause a fire or explo- POWER MODULE sion resulting in death or serious injury. To replace the fuses, follow these steps: 1. Turn off the refrigerator and unplug the power CHECKING THE CONTROL SYSTEM cord and disconnect the 12V wires. Check the control system by connecting/disconnecting the 2. Remove the power module cover. 120 VAC power, starting/stopping the engine, etc. 3. Snap the fuse out of the fuse holder and fit the new fuse in to the fuse holder. 4. Put back the power module cover.

DM2652 (OPTIONAL FAN), DM2852 (OPTIONAL FAN), DM2862 (OPTIONAL FAN) & NDM1062

INLINE FUSE The inline fuse for the power vent fans is connected to the 12V DC socket. To replace the inline fuse, follow these steps: 1. Disconnect 12V DC power. 2. Open the fuse holder.

12 MAINTENANCE & SERVICE CLEANING THE BURNER REFRIGERATOR REMOVAL / DIS- 1. Turn off the refrigerator POSAL 2. Unplug the power cord from the 120 VAC out- To be performed by a qualified service technician let. Disconnect the wires or shut off the 12 VDC power supply to the refrigerator. only. 3. Turn off the manual shut off valve. See Installation Instructions for refrigerator removal / 4. Remove cover from burner housing. replacement procedure, and for recycle information. 5. Clean the burner tube with a brush. Blow out the burner with compressed air.

FIRE HAZARD. Never use a wire or pin to clear obstructions from the burner jet as damage will occur. Do not attempt to adjust the burner jet. Failure to obey this warning could cause a fire resulting in death or serious injury.

6. Verify that the burner jet slots are centered under the flue tube. 7. Be sure to check the burner flame for proper appearance. The flame should be clear blue over the slots of the burner. Clear Blue Color Of Flame

Slots Centered Under Flue Tube

8. Check the electrode for proper location and gap. Adjustments may be made with needle nose pli- ers if necessary.

Electrode 1/8" to 3/16" (3-5 mm)

Burner Tube 9. Turn on the manual gas shut off valve. 10. Examine all fittings for leaks. Use a commercial non-corrosive bubble solution. 11. Connect the 120 VAC power cord. 12. Reconnect/Turn on the 12 VDC power. 13. Check LP gas safety shutoff.

13 TROUBLESHOOTING If you run into a problem, refer to the troubleshooting table below. Symptom Check/Remedial action Refrigerator stops cooling. • Immediately turn the refrigerator off and contact a Dometic dealer or Service Center. NOTE! Do not leave it running for an extended period of time, and never try to solve the problem by repeatedly restarting the refrigerator. • Do not use the refrigerator until it has been repaired Refrigerator emits an ammo- • Immediately turn the refrigerator off at the front control panel. nia smell • Do NOT open refrigerator doors. • Open coach windows and doors (to air out the coach) and evacuate. • Turn off manual LP gas valve at rear of refrigerator. • Disconnect the 120 VAC power at rear of refrigerator. • Contact a Dometic dealer or Service Center for repair. • Do not use the refrigerator until it has been repaired. Refrigerator or freezer is not • For refrigerators equipped with a thermostat, check the thermostat and adjust if cold enough necessary. • Is the plug firmly connected to the socket? Is the socket switched on? Check the socket by plugging in another appliance. • Is the refrigerator level? (Due to the nature of its operation it is important to keep an absorption refrigerator level.) • Door closing properly? Check the door gasket. • Heavy frost build-up on evaporator fins? To prevent frost build-up do not leave the unit’s door open longer than necessary. • Over packed refrigerator? The unit will have to work harder if the refrigerator is stuffed, and results in higher cabinet temperatures. Arrange the food in the unit to allow for free air circulation. Refrigerator does not work • Is the plug firmly connected to the receptacle? Is the receptacle energized? Check the on electric receptacle by plugging in another appliance. • Is there a power failure? • Blown fuse. Turn refrigerator off and contact a Dometic dealer or Service Center for repair. The refrigerator does not • LP gas bottle empty? Change the gas bottle. work in gas operation mode • Air in the gas line? Remove the air by repeating the ignition sequence. • If problem resists, turn refrigerator off and contact a Dometic dealer or Service Center for repair.

Refrigerator emits an odor • Dislocated or damaged burner. Turn refrigerator off and contact a Dometic dealer or from fumes: Service Center for repair. • Dirty flue tube. Turn refrigerator off and contact a Dometic dealer or Service Center for repair. Refrigerator too cold • Dislocated thermistor bracket. Clip thermistor bracket to last fin on right side of cooling flange and center vertically on fin. • Dislocated thermistor bulb. Position thermistor bulb inside thermistor bracket groove and center vertically in bracket.

If the problem persists and the refrigerator is still not working properly, turn refrigerator off and contact your nearest Ser- vice Center. State the problem, model, product, and serial number. These details are stated on the data label inside the refrigerator compartment.

14 APPENDIX A - SPARE PARTS

MODEL RM2351 RM2354 RM2451 RM2454 RM2551 RM2554 DM2652

SPARE PARTS Airing position card N/A N/A N/A N/A N/A N/A 3312986.403 Baffle 2007172022 2007172022 2932667013 2932667013 2932667021 2932667021 2932667039 Box 2932636018 2932636018 N/A N/A N/A N/A N/A Box, vegetable N/A N/A N/A N/A 2932621010 2932621010 2932621010 Box, vegetable N/A N/A N/A N/A N/A N/A N/A (crisper), 2 pieces Box, vegetable N/A N/A N/A N/A N/A N/A N/A (meat locker) Burner 2930697079 2930697079 2930697079 2930697079 2930697079 2930697079 2930697079 (with conductor) Door reversing kit, 385030401 385030401 N/A N/A N/A N/A N/A (light brown) Door reversing kit, 385030402 385030402 N/A N/A N/A N/A N/A (black) Door reversing kit, N/A N/A 293275002 293275002 293275002 293275002 293275008 right-left (light brown) Door reversing kit, N/A N/A 293275003 293275003 293275003 293275003 293275009 left-right (light brown) Door reversing kit, N/A N/A 293275013 293275013 293275013 293275013 293275011 right-left (black) Door reversing kit, N/A N/A 293275014 293275014 293275014 293275014 293275012 left-right (black) Door shelf, lower N/A N/A 2932575018 2932575018 2932575018 2932575018 2932575018 Door shelf, (2 pieces) N/A N/A 2932576016 2932576016 N/A N/A 2932576016 Door shelf, (3 pieces) 2002261242 2002261242 N/A N/A 2932576016 2932576016 N/A Door shelf, freezer N/A N/A N/A N/A N/A N/A 2932577014 Electrode 2932781012 2932781012 2932781012 2932781012 2932781012 2932781012 2932781012 Halogen lamp N/A N/A N/A N/A N/A N/A N/A (12V, 10W base G4) Handle (black) N/A N/A 2932670025 2932670025 2932670025 2932670025 3851174023 Heater 175W, 12V N/A 3850646104 N/A 3850646104 N/A 3850646104 N/A Heater 175W, 120V 3850644455 3850644455 3850644455 3850644455 3850644455 3850644455 N/A Heater 275W, 12V N/A N/A N/A N/A N/A N/A N/A Heater 325W, 120V N/A N/A N/A N/A N/A N/A 3850644422

15 APPENDIX A - SPARE PARTS

MODEL DM2662 DM2663 DM2852 DM2862 NDM1062

SPARE PARTS Airing position card 3312986.403 3312986.403 3312986.403 3312986.403 N/A Baffle 2932667039 2932667039 2932667047 2932667047 2932667047 Box N/A N/A N/A N/A N/A Box, vegetable 2932621077 2932621077 2932621010 2932621077 N/A Box, vegetable N/A N/A N/A N/A 2002726178 (crisper), 2 pieces Box, vegetable N/A N/A N/A N/A 2932621085 (meat locker) Burner 2930697079 2930697079 2930697079 2930697079 2930697079 (with conductor) Door reversing kit, N/A N/A N/A N/A N/A (light brown) Door reversing kit, N/A N/A N/A N/A N/A (black) Door reversing kit, N/A N/A 293275008 N/A N/A right-left (light brown) Door reversing kit, N/A N/A 293275009 N/A N/A left-right (light brown) Door reversing kit, 293275011 293275011 293275011 293275011 293275011 right-left (black) Door reversing kit, 293275012 293275012 293275012 293275012 293275012 left-right (black) Door shelf, lower 2932575059 2932575059 2932575018 2932575059 2932575075 Door shelf, (2 pieces) 2932576065 2932576065 N/A N/A N/A Door shelf, (3 pieces) N/A N/A 2932576016 2932576065 2932576081 Door shelf, freezer N/A N/A 2932577014 N/A N/A Electrode 2932781012 2932781012 2932781012 2932781012 2932781012 Halogen lamp N/A N/A N/A N/A 3850455019 (12V, 10W base G4) Handle (black) 3851174023 3851174023 3851174023 3851174023 2932094044 Heater 175W, 12V N/A N/A N/A N/A N/A Heater 175W, 120V N/A N/A N/A N/A N/A Heater 275W, 12V N/A 3850646096 N/A N/A N/A Heater 325W, 120V 3850644422 3850644422 3850644422 3850644422 3850644422

16 APPENDIX B - REARVIEW EQUIPMENT RM2351 & RM2354

3 3

RM2451, RM2454, RM2551 & RM2554

Heater Relay, 3-way only

Flue baffle

Power module cover Protection cover

12V DC

Screw for protection cover Burner jet 12 volt Terminal block Manual gas shutoff valve

Inlet fitting

Flexible cord Drain water hose

17 APPENDIX B - REARVIEW EQUIPMENT

DM2652, DM2662, DM2663, DM2852, DM2862 & NDM1062

Heater(s)

Relay, 3-Way only Thermofuse

Flue baffle

Power module cover Protection cover

12V DC

12 volt DC Screw for protection cover Terminal block Burner jet Drain water hose Flexible cord Manual gas Inlet fitting shutoff valve

Shown without Secondary Burner Housing for illustrative purposes only.

NDM1062 (WITH ICE MAKER)

Heater

Relay Thermofuse

Power Flue Baffle Module Cover

Protection Cover

12V DC

Flexible Cord Manual Gas Shutoff Valve Burner Jet Thermostat Flexible Cord 12V DC Inlet Fitting (Icemaker) Terminal Block 18 Drain Water Hose

Shown without Secondary Burner Housing for illustrative purposes only. APPENDIX C - WIRING DIAGRAM RM2351, RM2451 & RM2551

RM2354, RM2454 & RM2554

19 APPENDIX C - WIRING DIAGRAM DM2652, DM2662, DM2852 & DM2862 (NO FAN) WITH AND WITHOUT ICE MAKER

385 14 82

D T GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED P3−2 4 P1−5 N BROWN P3−1 9 P1−6 A BLACK P1−3

9 P2−1 M E 9 P2−2 8 C B 4 5 6 7 8 +12V GROUND 2 J J J J J J J1 0 L N J J 4 3 A J 6 1 1 3 J 5 J 7 3 1

J 2 5 A J 8 1 3 H G J10 J U 1 P 3 P 1 P 2

1 2 3 4 1 2 3 4 5 6 1 2 K F 9 P S 1 5 L 6 O T L N DISPLAY M BOARD 12V D C

E P PROTECTIVE EARTH A CIRCUIT BOARD POWER S CHASSIS GROUND B FUSE 3A T TEST POINT C FUSE 5A U THERMAL FUSE N D CIRCUIT BOARD DISPLAY E ELECTRODE F THERMOFUSE 1 BLACK G LAMP 2 BROWN U H SWITCH LAMP 3 RED F J HEATER 120V AC 4 YELLOW K HEATING CABLE 5 GREEN H G L TERMINAL BLOCK 6 GREEN/YELLOW M THERMISTOR 7 BLUE N SOLENOID VALVE 8 GREY K O RETAINER 9 WHITE

DM2652, DM2662, DM2852 & DM2862 (ONE FAN) WITH AND WITHOUT ICE MAKER

385 14 84

D T GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED P3−2 4 P1−5 N BROWN P3−1 9 P1−6 A BLACK P1−3

9 P2−1 M E 9 P2−2 8 C B 4 5 6 7 8 +12V GROUND 2 J J J J J J J1 0 U V L N 3 3 J 4 3 A J 6 3 3 X J 5 J 7 1 1 J 2 5 A J 8 1 1 1 J 3 J J10 H G Y 1 P 3 P 1 P 2

1 2 3 4 1 2 3 4 5 6 1 2 F 9 P S 1 5 K L 6 O T L N DISPLAY M BOARD 12V D C

E A CIRCUIT BOARD POWER S CHASSIS GROUND B FUSE 3A T TEST POINT C FUSE 5A U THERMOFUSE D CIRCUIT BOARD DISPLAY V FAN N E ELECTRODE X FUSE 3A F THERMOFUSE Y THERMAL FUSE G LAMP F H SWITCH LAMP 1 BLACK Y J HEATER 120V AC 2 BROWN K HEATING CABLE 3 RED V U L TERMINAL BLOCK 4 YELLOW

3 A M THERMISTOR 5 GREEN H G N SOLENOID VALVE 6 GREEN/YELLOW O RETAINER 7 BLUE P PROTECTIVE EARTH 8 GREY 9 WHITE K 20 APPENDIX C - WIRING DIAGRAM DM2663 (NO FAN) WITHOUT ICE MAKER

385 14 83 8 5 8 7

D X P GREEN P1−1 ORANGE P3−4 7 8 6 3 0 P1−4 BLUE P3−3 7 P1−2 RED P3−2 4 P1−5 A O BROWN P3−1 9 P1−6 BLACK P1−3

9 P2−1 N E 9 P2−2 8 C B +12V GROUND 4 5 L N 2 6 7 8 J J J J J J J1 0 W 3 J 4 3 A J 6 3 3 J 5 J 7 1 1 1 J 2 5 A J 8 3 3

1 J 1 K J10 K 3 H G P 3 P 1 P 2 Y 1 1 2 3 4 1 2 3 4 5 6 1 2 F 9 S U L 1 5 X M 6 R DISPLAY N BOARD L N 1 2 V D C Y E J A CIRCUIT BOARD POWER S PROTECTIVE EARTH B FUSE 3A U CHASSIS GROUND 8 5 8 7 C FUSE 5A W FUSE 30A F P D CIRCUIT BOARD DISPLAY X TEST POINT W E ELECTRODE Y THERMAL FUSE 8 6 3 0 F THERMOFUSE G LAMP H SWITCH LAMP 1 BLACK O J HEATER 12V DC 2 BROWN K HEATER 120V AC 3 RED L HEATING CABLE 4 YELLOW H G M TERMINAL BLOCK 5 GREEN N THERMISTOR 6 GREEN/YELLOW O SOLENOID VALVE 7 BLUE L P RELAY 8 GREY R RETAINER 9 WHITE

NDM1062 (STAINLESS STEEL DOORS) 385 14 04 D T +12 V LA C GN D J CL C GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED A P3−2 4 P1−5 O BROWN P3−1 9 P1−6 BLACK P1−3

9 P2−1 L 9 P2−2 E C 8 1 B 8 4 3 2 5 6 7 8 J 3 J J J J J J1 0 M N 1 3 3 3 1 1 +12V GROUND L N V 3 1 J 4 3 A J 6 1 1 J 5 J 7 1 H J 2 5 A J 8 3 Y 1

J10 H U 9 R S 1 5 P 3 P 1 P 2 8 K 6 P 1 2 3 4 1 2 3 4 5 6 1 2 G F L N

T 12V D C

DISPLAY L BOARD A CIRCUIT BOARD POWER R PROTECTIVE EARTH B FUSE 3A S CHASSIS GROUND

+12 V LA C GN D CL C C FUSE 5A T TEST POINT D CIRCUIT BOARD DISPLAY U THERMOFUSE E ELECTRODE V FUSE 3A M F LAMP Y THERMAL FUSE G SWITCH LAMP 3 A 1 BLACK E H HEATER 120V AC J HEATING CABLE 2 BROWN K TERMINAL BLOCK 3 RED L THERMISTOR 4 YELLOW J N M THERMOFUSE 5 GREEN N FANS 6 GREEN/YELLOW G O SOLENOID VALVE 7 BLUE Y F P RETAINER 8 GREY 9 WHITE U O

21 APPENDIX C - WIRING DIAGRAM NDM1062 (STAINLESS STEEL DOORS & ICE MAKER)

385 14 44 D T +12 V J LA C GN D CL C GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED A P3−2 4 P1−5 O BROWN P3−1 9 P1−6 BLACK P1−3

9 P2−1 L 9 P2−2 E C 8 1 B 8 4 2 3 5 6 7 8 J J J1 0 3 J J J J M N 1 3 3 3 1 1

V +12V GROUND 3 1 3 L N 1 1 J 4 3 A J 6 1 H J 5 J 7 3 J 2 5 A J 8 F Y 1

U J10 H 8 R S 9 K P 3 P 1 P 2 6 P G 1 5 1 2 3 4 1 2 3 4 5 6 1 2 1 L N 12V D C T 8 5 8 6 9 L DISPLAY 3 1 8 7 3 0 BOARD 2 6 6 AD 9 AG 3 6 +12 V LA C GN D CL C AA AE M B 4 AC 1 1 M 5 AB 1 9 ° C E L N AF 120 V AC

J N A CIRCUIT BOARD POWER V PROTECTIVE EARTH B FUSE 3A Y CHASSIS GROUND G C FUSE 5A AA ICEMAKER F D CIRCUIT BOARD DISPLAY AB WATER VALVE U O E ELECTRODE AC TERMINAL BLOCK Y F LAMP AD RELAY G SWITCH LAMP AE HEATING CABLE H HEATER 120V AC AF THERMOSTAT J HEATING CABLE AG FUSE 4A 8 6 8 5 K TERMINAL BLOCK 3 0 8 7 AA L THERMISTOR 1 BLACK AD M THERMOFUSE 2 BROWN 3 A AG N FANS 3 RED O SOLENOID VALVE 4 YELLOW AE P RETAINER 5 GREEN M B 4 R PROTECTIVE EARTH 6 GREEN/YELLOW S CHASSIS GROUND 7 BLUE ° C AB T TEST POINT 8 GREY L N GROUND U THERMOFUSE 9 WHITE AF

22 APPENDIX C - WIRING DIAGRAM NDM1062 (DOOR INSERT PANELS)

385 14 05 D Z GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED A P3−2 4 P1−5 O BROWN P3−1 9 P1−6 BLACK P1−3

9 P2−1 L 9 P2−2 E C 8 B 5 6 7 8 J 2 4 J J J J J J J1 0 M N

+12V GROUND 3 3 3 Y 1 1 L N T 3 1 J 4 3 A J 6 3 1 1 1 J 5 J 7 1 3 1 J 2 5 A J 8 H 3 3 8 R 1 J10 H W U 9 S X P 3 P 1 P 2 G 1 5 K 1 2 3 4 1 2 3 4 5 6 1 2 8 6 P

F L N Z 12V D C DISPLAY L BOARD S PROTECTIVE EARTH A CIRCUIT BOARD POWER T SWITCH B FUSE 3A U SWITCH L.A.C E C FUSE 5A W THERMOFUSE D CIRCUIT BOARD DISPLAY X CHASSIS GROUND

3 A E ELECTRODE Y FUSE 3A G F F LAMP Z TEST POINT M G SWITCH LAMP H HEATER 120V AC 1 BLACK U J HEATING CABLE 2 BROWN K TERMINAL BLOCK 3 RED

J L THERMISTOR 4 YELLOW N M THERMOFUSE 5 GREEN R T N FANS 6 GREEN/YELLOW O SOLENOID VALVE 7 BLUE

W P RETAINER 8 GREY R THERMAL FUSE 9 WHITE O

NDM1062 (DOOR INSERT PANELS & ICE MAKER)

385 14 52 D Z J GREEN P1−1 ORANGE P3−4 P1−4 BLUE P3−3 P1−2 RED A P3−2 4 T P1−5 O BROWN P3−1 9 P1−6 BLACK P1−3 1 9 P2−1 1 3 L 9 P2−2 E C 8 B 2 5 6 7 8 3 4 J J J J J J1 0 8 J M N U 3 3 3 3 1 1

Y +12V GROUND 3 1 3 1 L N 1 1 J 4 3 A J 6 H

J 5 J 7 3 R 1 J 2 5 A J 8 F W 8 S X J10 H 9 K 6 P G 1 5 P 3 P 1 P 2 1 2 3 4 1 2 3 4 5 6 1 2 1 L N 12V D C

8 5 8 6 9 Z 3 1 8 7 3 0 DISPLAY L 2 BOARD 6 6 AD 9 AG 3 6 AA E AE M B 4 AC 1 1 5 AB 1 9 G F ° C M L N AF 120 V AC U A CIRCUIT BOARD POWER X CHASSIS GROUND B FUSE 3A Y FUSE 3A C FUSE 5A Z TEST POINT N T J D CIRCUIT BOARD DISPLAY AA ICEMAKER W E ELECTRODE AB WATER VALVE R F LAMP AC TERMINAL BLOCK G SWITCH LAMP AD RELAY O H HEATER 120V AC AE HEATING CABLE J HEATING CABLE AF THERMOSTAT K TERMINAL BLOCK AG FUSE 4A 8 6 8 5 L THERMISTOR 3 0 8 7 AA M THERMOFUSE 1 BLACK AD N FANS 2 BROWN AG 3 A O SOLENOID VALVE 3 RED P RETAINER 4 YELLOW AE R THERMAL FUSE 5 GREEN M B 4 S PROTECTIVE EARTH 6 GREEN/YELLOW T SWITCH 7 BLUE ° C AB U SWITCH L.A.C 8 GREY L N GROUND W THERMOFUSE 9 WHITE AF

23 APPENDIX D - CONSUMER SUPPORT

Dometic website www.DometicUSA.com Please visit our website for information and news about Dometic products. Our website provides information on product care and warranties. You can also download product literature, including manuals and brochures.

Service and spare parts www.eDometic.com For service and spare parts, please contact Service Center Assistance. Please see the front page of this manual - or - visit our Dometic website to find a Dometic Service Center near you.

Contact us www.DometicUSA.com For contact information, please see the front page of this manual - or - visit our Dometic website.

Register product www.eDometic.com Timely registration allows for enhanced communication and service under the terms of your warranty. Please see “Appendix E - Dometic Warranty” on page (25). To register your product, fill in the pre-printed registration card on the last page of this manual, or register on-line at www.eDometic.com.

TO REGISTER ON-LINE: Access www.eDometic.com then click “Register your Dometic PRODUCT.” 1. 

2. Complete the on-line form, then click “SUBMIT”.

24 APPENDIX E - DOMETIC WARRANTY LIMITED TWO-YEAR WARRANTY (DOMETIC REFRIGERATORS) THE SELLER NAMED BELOW MAKES THE FOLLOWING WARRANTY WITH RESPECT TO THE DOMETIC PRODUCT: 1. This Warranty is made only to the first purchaser (hereinafter referred to as the “Original Purchaser”), who acquires the Dometic Product for his or her own use and when the Dometic Product is installed and operated within the continental United States and Canada. 2. WARRANTY PERIOD: This Warranty will be in effect for two (2) years from the date of purchase by the Original Purchaser. The Original Purchaser should retain a copy of the dated bill of sale as evidence of the date of purchase. 3. WARRANTY: This Warranty covers labor, specified parts, and freight. The Dometic Product shall be free from defects in material and workmanship at the time of sale and under normal use. All Dometic Products (except those specifically built for commercial use) are warranted only when installed per the Seller’s installation instructions on vehicles built to R.V.I.A. A119-2 and C.R.V.A. Z-240 Standards. This Warranty does NOT cover conditions unrelated to the material and workmanship of the Dometic Product. Such unrelated conditions include, but are not limited to: (a) damage not reported within 10 days of ownership; (b) faulty installation or installation that does not comply with the Seller’s instructions or R.V.I.A. and C.R.V.A. standards, and any damage resulting from such; (c) damage or failure caused by installation of accessories not manufactured and marketed by the Seller or any non-Dometic parts that are installed as replacement parts; (d) the need for normal maintenance and any damage resulting from the failure to provide such maintenance; (e) failure to follow Seller’s instructions for use of this Dometic Product; (f) flame outage due to blow out or high altitude; (g) reduced performance due to high altitude; (h) radio frequency interference (RFI) or electromagnetic interference (EMI); (i) 12 VDC system chassis ground decay and corrosion; (j) puncture of foam cabinet or vacuum insulated panels after acknowledged receipt; (k) animal or insect infiltration which damages unit or inhibits performance; (l) any accident to, or misuse of, any part of the Dometic Product and any alteration by anyone other than the Seller or its authorized representative; and (m) normal wear. 4. WARRANTY COVERS DOMETIC COMPONENT PARTS: Major components (cooling unit, LP gas valve, burner, burner housing, electronic display, electronic module, evaporator fins, foam integrity, frame, thermistor, spark probe, ignition wire, ice maker compressor, second absorption loop, display escutcheon, lower toe plate, humidity switch, frame heater mullion, ice maker mullion) are covered for labor, parts and freight for two (2) years from date of purchase. All other components that fail must be reported within the first 90 days of ownership in order to receive warranty coverage for labor, parts and freight. 5. The Original Purchaser must provide preventative maintenance on a yearly basis, beginning at the first anniversary of the date of purchase. The Original Purchaser must keep a record of the preventative maintenance to keep the warranty in effect. Failure of the Original Purchaser in providing this annual maintenance may void the warranty. The preventative maintenance must be performed at a Dometic Authorized Service Center/Dealer. The required preventative maintenance is an inspection, cleaning and full diagnostics performed on the entire electronic system, burner assembly, wiring and cooling unit. A copy of the receipt covering the maintenance checks must accompany the warranty claim during the second year of ownership. The cost of this preventative maintenance is the Original Purchaser’s responsibility and the preventative maintenance should take about one hour. 6. WARRANTY REMEDY: In order to obtain the benefits of this Warranty, the Original Purchaser has the following two options during the WARRANTY PERIOD: a. Preferred option: Deliver the Dometic Product for inspection to the nearest Authorized Dometic Service Center during the Warranty Period. To obtain the location of the nearest Authorized Dometic Service Center, refer to https://www.dometic.com/en-us/us/find-a-dealer. The Authorized Dometic Service Center will work with the Seller to obtain Warranty coverage if a Seller defect is identified. CONFIRM THE SERVICE CENTER IS AN AUTHORIZED DOMETIC SERVICE CENTER. DO NOT PAY THE SERVICE CENTER FOR WARRANTY REPAIRS. b. Second option: If it is not feasible under the circumstances to deliver the Dometic Product to an Authorized Dometic Service Center, please call 1-800- 544-4881 for additional Warranty assistance. Seller prefers option a. first and only option b. if option a. is determined not to be feasible under the circumstances. 7. Any item returned in the manner described in paragraph 6 will be examined by the Authorized Dometic Service Center. If it is found that the returned item was defective in material and workmanship at the time of sale, the Authorized Dometic Service Center will contact the Seller for Warranty coverage. The Seller shall, at Dometic’s sole option, repair or replace the Dometic Product, or refund Original Purchaser’s purchase price. If the Seller determines that repairs to the Dometic Product are to be made, then only authorized Dometic parts will be used. 8. The Seller does not authorize any person or company to create any Warranty obligations or liability on its behalf. This Warranty is not extended by the length of time which you are deprived of the use of the Dometic Product. 9. IN NO EVENT SHALL SELLER BE LIABLE FOR EITHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS INCLUDES ANY DAMAGE TO ANOTHER PRODUCT OR PRODUCTS RESULTING FROM SUCH A DEFECT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 10. ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PURPOSE, IS LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 11. THIS WARRANTY GIVES SPECIFIC LEGAL RIGHTS, YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. No action to enforce this Warranty shall be commenced later than ninety (90) days after the expiration of the Warranty Period. Claims must be submitted in writing to the Dometic Warranty Department. 12. The Seller reserves the right to change the design of any Dometic product without notice and with no obligation to make corresponding changes in Dometic products previously manufactured.

PROTECTION FOR YOUR NEW INVESTMENT Dometic Corporation We appreciate that you have chosen to purchase a Warranty Department Form No. 3316980.000 (10/17) Dometic product for your recreational vehicle and we want to help 1120 North Main Street (French 3316985.000) you protect this wise investment. We at Dometic, back our prod- Elkhart, Indiana 46514 ©2017 Dometic Corporation ucts with one of the most comprehensive warranties in the industry. 1-574-294-2511 LaGrange, IN 46761 Register your product online at: www.eDometic.com. Register Your Product @ www.eDometic.com 25 APPENDIX F - MAINTENANCE SCHEDULE REFRIGERATOR OWNER MAINTENANCE YEARLY RECORD

Customer Name: Model No.: Date of Purchase: Address: Serial No.: City: State: Zip Code: Phone:

FIRST YEAR SECOND YEAR

Date: Date: Dealership: Dealership:

Address: Address:

City: City: State: Zip: State: Zip: Phone: Phone: Technician: Technician:

Cleaned Burner Assembly: Yes / No Cleaned Burner Assembly: Yes / No Cleaned/Check All Terminals Connections: Yes / No Cleaned/Check All Terminals Connections: Yes / No Cleaned/Inspect All Ground Connections: Yes / No Cleaned/Inspect All Ground Connections: Yes / No Inspect and Test Door Seals: Yes / No Inspect and Test Door Seals: Yes / No Inspect and Tighten LP Lines: Yes / No Inspect and Tighten LP Lines: Yes / No Power Ventilator Installed: Yes / No Power Ventilator Installed: Yes / No Gas Safety Shutdown in 45 seconds: Yes / No Gas Safety Shutdown in 45 seconds: Yes / No

ACTUAL SPEC. RANGE ACTUAL SPEC. RANGE Electrode Gap 3/16” Electrode Gap 3/16” Thermistor Reading 7-10,000 ohms @ 32° Thermistor Reading 7-10,000 ohms @ 32° D/C Voltage 9.5 to 15 volts D/C D/C Voltage 9.5 to 15 volts D/C A/C Voltage 120 Volts ± 10% A/C Voltage 120 Volts ± 10% Thermocouple Reading 25-35 Millivolts Thermocouple Reading 25-35 Millivolts Delay Between Modes Approx. 5 seconds Delay Between Modes Approx. 5 seconds

ICE MAKER MODELS ICE MAKER MODELS Inspect Water Valve and All Connections: Yes / No Inspect Water Valve and All Connections: Yes / No Inspect Heat Tape Switch for Proper Inspect Heat Tape Switch for Proper Operation: Yes / No Operation: Yes / No