SMITH CHART EXAMPLES

Dragica Vasileska ASU Smith Chart for the Impedance Plot

It will be easier if we normalize the load impedance to the of the attached to the load. Z z = = r + jx Zo 1+ Γ z = 1− Γ Since the impedance is a , the will be a complex number Γ = u + jv

2 2 2v 1− u − v x = r = 2 2 ()1− u 2 + v2 ()1− u + v Real Circles 1 Im {Γ}

0.5

r=0 r=1/3 r=1 r=2.5 1 0.5 0 0.5 1 Re {Γ}

0.5

1 Imaginary Circles Im 1 {Γ}

x=1/3 x=1 x=2.5 0.5

{Γ} 1 0.5 0 0.5 1 Re

x=-1/3 x=-1 x=-2.5 0.5

1

Normalized Y y = = YZ o = g + jb Yo 1− Γ y = 1+ Γ 2 1− u 2 − v2  g  1  u +  + v2 = g =   2 ()1+ u 2 + v2  1+ g  ()1+ g

− 2v 2 b = 2  1  1 2 2 ()u +1 +  v +  = ()1+ u + v  b  b2

These are equations for circles on the (u,v) plane Real admittance

1 Im {Γ}

0.5

g=2.5 g=1 g=1/3 1 0.5 0 0.5Re {Γ} 1

0.5

1 Complex Admittance

1 Im {Γ}

b=-1 b=-1/3

b=-2.5 0.5

1 0.5 0 0.5Re {Γ 1}

b=2.5 b=1/3

0.5 b=1

1 Matching

• For a matching network that contains elements connected in series and parallel, we will need two types of Smith charts – impedance Smith chart – admittance Smith Chart • The admittance Smith chart is the impedance Smith chart rotated 180 degrees. – We could use one Smith chart and flip the reflection coefficient vector 180 degrees when switching between a series configuration to a parallel configuration. Toward Constant Generator Reflection Coefficient Circle

Away From Generator

Full Circle is One Half Since Everything Repeats Matching Example

Ps Z0 = 50 Ω M 100 Ω

Γ = 0

Match 100 Ω load to a 50 Ω system at 100MHz

A 100 Ω resistor in parallel would do the trick but ½ of the power would be dissipated in the matching network. We want to use only lossless elements such as inductors and capacitors so we don’t dissipate any power in the matching network Matching Example  We need to go from z=2+j0 to z=1+j0 on the Smith chart  We won’t get any closer by adding series impedance so we will need to add something in parallel.  We need to flip over to the admittance chart

Impedance Chart Matching Example  y=0.5+j0  Before we add the admittance, add a mirror of the r=1 circle as a guide.

Admittance Chart Matching Example

 y=0.5+j0  Before we add the admittance, add a mirror of the r=1 circle as a guide  Now add positive imaginary admittance.

Admittance Chart Matching Example  y=0.5+j0  Before we add the admittance, add a mirror of the r=1 circle as a guide  Now add positive imaginary admittance jb = j0.5 jb = j0.5 5.0j = 2j π()100 MHz C 50 Ω C =16 pF

16 pF 100 Ω Admittance Chart Matching Example

 We will now add series impedance  Flip to the impedance Smith Chart  We land at on the r=1 circle at x=-1

Impedance Chart Matching Example

 Add positive imaginary admittance to get to z=1+j0 jx = 0.1j ()()0.1j 50 Ω = 2j π 100 MHz L L = 80 nH 80 nH

16 pF 100 Ω

Impedance Chart Matching Example

 This solution would have also worked 32 pF

100 Ω 160 nH Impedance Chart Mainstream vs. RF Electronics MESFET Gate Source Drain Metal-Semiconductor FET n+ cap n+ cap L n-type active layer

Buffer

Substrate

HEMT High Electron Mobility Transistor Gate Source Drain Channel: twodimensional electron n+ cap n+ cap L Barrier gas (2DEG) at the inter-

Barrier / buffer face channel layer - barrier

Substrate 2DEG channel Channel layer E. Simulation Examples  Example #1 This Example gives comparison of the device outputcharacte- ristics of a single quantum-well structure when gusin drift-dif- fusion and energy balance models

 Example #2 Simulation results of a pseudomorphic HEMT structure: device transfer and output characteristics with extraction of some significant device parameters, such as thresholdltage, vo maximum saturation current, etc.

 Example #3 This is a follow-up of Example #2, in which AC ysisanal is performed and the device S-parameters calculated. Example 1 Example 1 (cont’d) Example 1 (cont’d) Example 2 Example 3 Example 3 (cont’d)