DOCSLIB.ORG

47 CFR Ch. I (10–1–09 Edition)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
47 CFR Ch. I (10–1–09 Edition) § 2.1047 47 CFR Ch. I (10–1–09 Edition) so adjusted that the two principal fre- the peak envelope power output versus quency components of the radio fre- the modulation input voltage shall be quency signal produced are equal in supplied. The modulating signals shall magnitude. be the same in frequency as specified in (5) Independent sideband transmit- paragraph (c) of § 2.1049 for the occupied ters having more than two channels by bandwidth tests. an appropriate signal or signals applied (d) Other types of equipment. A curve to all channels simultaneously. The or equivalent data which shows that input signal or signals shall simulate the equipment will meet the modula- the input signals specified by the man- tion requirements of the rules under ufacturer for normal operation. which the equipment is to be licensed. (6) Single-channel controlled-carrier [39 FR 5919, Feb. 15, 1974. Redesignated and transmitters in the A3 emission mode— amended at 63 FR 36599, July 7, 1998] by a 2500 Hz tone. (c) For measurements conducted pur- § 2.1049 Measurements required: Occu- suant to paragraphs (a) and (b) of this pied bandwidth. section, all calculations and methods The occupied bandwidth, that is the used by the applicant for determining frequency bandwidth such that, below carrier power or peak envelope power, its lower and above its upper frequency as appropriate, on the basis of meas- limits, the mean powers radiated are ured power in the radio frequency load each equal to 0.5 percent of the total attached to the transmitter output ter- mean power radiated by a given emis- minals shall be shown. Under the test sion shall be measured under the fol- conditions specified, no components of lowing conditions as applicable: the emission spectrum shall exceed the (a) Radiotelegraph transmitters for limits specified in the applicable rule manual operation when keyed at 16 parts as necessary for meeting occu- dots per second. pied bandwidth or emission limita- (b) Other keyed transmitters—when tions. keyed at the maximum machine speed. [39 FR 5919, Feb. 15, 1974. Redesignated and (c) Radiotelephone transmitters amended at 63 FR 36599, July 7, 1998] equipped with a device to limit modu- lation or peak envelope power shall be § 2.1047 Measurements required: Mod- modulated as follows. For single side- ulation characteristics. band and independent sideband trans- (a) Voice modulated communication mitters, the input level of the modu- equipment. A curve or equivalent data lating signal shall be 10 dB greater showing the frequency response of the than that necessary to produce rated audio modulating circuit over a range peak envelope power. of 100 to 5000 Hz shall be submitted. For (1) Other than single sideband or equipment required to have an audio independent sideband transmitters— low-pass filter, a curve showing the fre- when modulated by a 2500 Hz tone at an quency response of the filter, or of all input level 16 dB greater than that nec- circuitry installed between the modu- essary to produce 50 percent modula- lation limiter and the modulated stage tion. The input level shall be estab- shall be submitted. lished at the frequency of maximum re- (b) Equipment which employs modula- sponse of the audio modulating circuit. tion limiting. A curve or family of (2) Single sideband transmitters in curves showing the percentage of mod- A3A or A3J emission modes—when ulation versus the modulation input modulated by two tones at frequencies voltage shall be supplied. The informa- of 400 Hz and 1800 Hz (for 3.0 kHz au- tion submitted shall be sufficient to thorized bandwidth), or 500 Hz and 2100 show modulation limiting capability Hz (for 3.5 kHz authorized bandwidth), throughout the range of modulating or 500 Hz and 2400 Hz (for 4.0 kHz au- frequencies and input modulating sig- thorized bandwidth), applied simulta- nal levels employed. neously. The input levels of the tones (c) Single sideband and independent shall be so adjusted that the two prin- sideband radiotelephone transmitters cipal frequency components of the which employ a device or circuit to limit radio frequency signal produced are peak envelope power. A curve showing equal in magnitude. 640 VerDate Nov<24>2008 14:41 Dec 08, 2009 Jkt 217200 PO 00000 Frm 00650 Fmt 8010 Sfmt 8010 Y:\SGML\217200.XXX 217200 cprice-sewell on DSK2BSOYB1PROD with CFR.
Load more

Recommended publications
  • Radio Communications in the Digital Age
    Radio Communications In the Digital Age Volume 1 HF TECHNOLOGY Edition 2 First Edition: September 1996 Second Edition: October 2005 © Harris Corporation 2005 All rights reserved Library of Congress Catalog Card Number: 96-94476 Harris Corporation, RF Communications Division Radio Communications in the Digital Age Volume One: HF Technology, Edition 2 Printed in USA © 10/05 R.O. 10K B1006A All Harris RF Communications products and systems included herein are registered trademarks of the Harris Corporation. TABLE OF CONTENTS INTRODUCTION...............................................................................1 CHAPTER 1 PRINCIPLES OF RADIO COMMUNICATIONS .....................................6 CHAPTER 2 THE IONOSPHERE AND HF RADIO PROPAGATION..........................16 CHAPTER 3 ELEMENTS IN AN HF RADIO ..........................................................24 CHAPTER 4 NOISE AND INTERFERENCE............................................................36 CHAPTER 5 HF MODEMS .................................................................................40 CHAPTER 6 AUTOMATIC LINK ESTABLISHMENT (ALE) TECHNOLOGY...............48 CHAPTER 7 DIGITAL VOICE ..............................................................................55 CHAPTER 8 DATA SYSTEMS .............................................................................59 CHAPTER 9 SECURING COMMUNICATIONS.....................................................71 CHAPTER 10 FUTURE DIRECTIONS .....................................................................77 APPENDIX A STANDARDS
    [Show full text]
  • A High-Performance, Single-Signal, Direct-Conversion Receiver with DSP Filtering
    By Rob Frohne, KL7NA A High-Performance, Single- Signal, Direct-Conversion Receiver with DSP Filtering By adding a DSP demodulator to a well-established and popular receiver design—KK7B’s R2— you can have a bit of the latest filter technology at your fingertips! ith so many new radios incor- realistic to have a digital filter with the Motorola 56002 processor uses 24 bits of porating digital signal proces- equivalent of hundreds of poles. (In the precision; the TI TMS320C5X uses only sing (DSP) for demodulation analog domain, it takes one inductor or 16. It was obvious that we needed to start W and filtering, I got the itch to capacitor to make one pole.) Few analog over. play with one myself. By “play with one,” designers use more than ten poles in a fil- That start didn’t come until I taught a I don’t mean merely operate a DSP- ter, because it’s very difficult to make an communication systems course during the equipped receiver, I wanted to be able to analog filter with more than about ten poles winter quarter of 1996. As a homework as- put my own software into the receiver and work properly. signment, I had my students try the Motorola put to work some of those nifty signal-pro- EVM (evaluation module) in place of the cessing ideas I teach others how to use! Some Background TI DSK. It proved simple to modify a filter This project started in 1994. Ralph program supplied by Motorola to do the Why DSP? Stirling, KC3F, and I did exactly what Rick basic filtering necessary for SSB demo- You may wonder “What’s the big deal?” Campbell, KK7B, suggested in his R2 re- dulation, and it worked much better than the Why are so many of the new radios sup- ceiver article.1 (Get your copy of that article TI DSK-based receiver.
    [Show full text]
  • Technical Handbook for Radio Monitoring HF
    Technical Handbook for Radio Monitoring HF Edition 2013 2 Dipl.- Ing. Roland Proesch Technical Handbook for Radio Monitoring HF Edition 2013 Description of modulation techniques and waveforms with 259 signals, 448 pictures and 134 tables 3 Bibliografische Information der Deutschen Nationalbibliothek Die Deutsche Nationalbibliothek verzeichnet diese Publikation in der Deutschen Nationalbibliografie; detaillierte bibliografische Daten sind im Internet über http://dnb.d-nb.de abrufbar. © 2013 Dipl.- Ing. Roland Proesch Email: [email protected] Production and publishing: Books on Demand GmbH, Norderstedt, Germany Cover design: Anne Proesch Printed in Germany Web page: www.frequencymanager.de ISBN 9783732241422 4 Acknowledgement: Thanks for those persons who have supported me in the preparation of this book: Aikaterini Daskalaki-Proesch Horst Diesperger Luca Barbi Dr. Andreas Schwolen-Backes Vaino Lehtoranta Mike Chase Disclaimer: The information in this book have been collected over years. The main problem is that there are not many open sources to get information about this sensitive field. Although I tried to verify these information from different sources it may be that there are mistakes. Please do not hesitate to contact me if you discover any wrong description. 5 6 Content 1 LIST OF PICTURES 19 2 LIST OF TABLES 29 3 REMOVED SIGNALS 33 4 GENERAL 35 5 DESCRIPTION OF WAVEFORMS 37 1.1 Analogue Waveforms 37 Amplitude Modulation (AM) 37 Double Sideband reduced Carrier (DSB-RC) 38 Double Sideband suppressed Carrier (DSB-SC) 38 Single Sideband
    [Show full text]
  • Maintenance of Remote Communication Facility (Rcf)
    ORDER rlll,, J MAINTENANCE OF REMOTE commucf~TIoN FACILITY (RCF) EQUIPMENTS OCTOBER 16, 1989 U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION AbMINISTRATION Distribution: Selected Airway Facilities Field Initiated By: ASM- 156 and Regional Offices, ZAF-600 10/16/89 6580.5 FOREWORD 1. PURPOSE. direction authorized by the Systems Maintenance Service. This handbook provides guidance and prescribes techni- Referenceslocated in the chapters of this handbook entitled cal standardsand tolerances,and proceduresapplicable to the Standardsand Tolerances,Periodic Maintenance, and Main- maintenance and inspection of remote communication tenance Procedures shall indicate to the user whether this facility (RCF) equipment. It also provides information on handbook and/or the equipment instruction books shall be special methodsand techniquesthat will enablemaintenance consulted for a particular standard,key inspection element or personnel to achieve optimum performancefrom the equip- performance parameter, performance check, maintenance ment. This information augmentsinformation available in in- task, or maintenanceprocedure. struction books and other handbooks, and complements b. Order 6032.1A, Modifications to Ground Facilities, Order 6000.15A, General Maintenance Handbook for Air- Systems,and Equipment in the National Airspace System, way Facilities. contains comprehensivepolicy and direction concerning the development, authorization, implementation, and recording 2. DISTRIBUTION. of modifications to facilities, systems,andequipment in com- This directive is distributed to selectedoffices and services missioned status. It supersedesall instructions published in within Washington headquarters,the FAA Technical Center, earlier editions of maintenance technical handbooksand re- the Mike Monroney Aeronautical Center, regional Airway lated directives . Facilities divisions, and Airway Facilities field offices having the following facilities/equipment: AFSS, ARTCC, ATCT, 6. FORMS LISTING. EARTS, FSS, MAPS, RAPCO, TRACO, IFST, RCAG, RCO, RTR, and SSO.
    [Show full text]
  • Federal Communications Commission § 97.307
    Federal Communications Commission § 97.307 § 97.307 Emission standards. (1) No angle-modulated emission may have a modulation index greater than 1 (a) No amateur station transmission at the highest modulation frequency. shall occupy more bandwidth than nec- (2) No non-phone emission shall ex- essary for the information rate and ceed the bandwidth of a communica- emission type being transmitted, in ac- tions quality phone emission of the cordance with good amateur practice. same modulation type. The total band- (b) Emissions resulting from modula- width of an independent sideband emis- tion must be confined to the band or sion (having B as the first symbol), or segment available to the control opera- a multiplexed image and phone emis- tor. Emissions outside the necessary sion, shall not exceed that of a commu- bandwidth must not cause splatter or nications quality A3E emission. keyclick interference to operations on (3) Only a RTTY or data emission adjacent frequencies. using a specified digital code listed in (c) All spurious emissions from a sta- § 97.309(a) of this part may be transmit- tion transmitter must be reduced to ted. The symbol rate must not exceed the greatest extent practicable. If any 300 bauds, or for frequency-shift key- spurious emission, including chassis or ing, the frequency shift between mark power line radiation, causes harmful and space must not exceed 1 kHz. interference to the reception of an- (4) Only a RTTY or data emission other radio station, the licensee of the using a specified digital code listed in interfering amateur station is required § 97.309(a) of this part may be transmit- to take steps to eliminate the inter- ted.
    [Show full text]
  • Southwest Region Spectrum Management Handbook
    ORDER SW 6050.12A SOUTHWEST REGION SPECTRUM MANAGEMENT HANDBOOK (Date of Order to be entered at time of ASW-400 signature) DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION Distribution: A-X-5; A-FAF/AT-0 (STD) Initiated By: ASW-473 RECORD OF CHANGES DIRECTIVE NO. SW 6050.12A CHANGE SUPPLEMENTS OPTIONAL CHANGE SUPPLEMENTS OPTIONAL TO TO BASIC BASIC 12/12/01 SW 6050.12A FOREWORD The radio frequency spectrum is a finite, vital, and very limited natural resource available to all countries of the world. This international resource serves mankind in innumerable ways, and each country exercises its own sovereign rights in the use of the electromagnetic waves. Because the radio spectrum knows no bounds, its use cannot be restricted to individual countries. Requirements for use of this resource generally exceed the amount available; therefore, it is necessary that international, national, and regional spectrum management be rigidly practiced. The purpose of this spectrum management order is to present radio frequency spectrum information, guidance, and policy to those organizations using or administrating the radio frequency spectrum within the Southwest Region. Marcos Costilla Manager, Airway Facilities Division Page i (and ii) SW 6050.12A 12/12/01 Page ii 12/12/01 SW 6050.12A TABLE OF CONTENTS CHAPTER 1. ORGANIZATION, AUTHORITY AND RESPONSIBILITY 1. Purpose..................................................................................................................................................................... 1 2. Distribution..............................................................................................................................................................
    [Show full text]
  • MT's 2011 Amateur Radio Special
    www.monitoringtimes.com Scanning - Shortwave - Ham Radio - Equipment Internet Streaming - Computers - Antique Radio ® Volume 30, No. 5 May 2011 U.S. $6.95 Can. $6.95 Printed in the A Publication of Grove Enterprises United States MT’s 2011 Amateur Radio Special In this issue: • SSTV in the Digital Age • Young Ladies’ Radio League • Small Space Operating: You can do it! AR5001D Wide Coverage Professional Grade Communications Receiver Discover the next generation in AOR’s legendary line of professional grade The Legend desktop communications receivers. ■ Multimode receives AM, wide and narrow Lives On! FM, upper and lower sideband and CW ■ Up to 2000 alphanumeric memories (50 channels X 40 banks) can be stored ■ Analog S-meter ■ Fast Fourier Transform algorithms ■ Operated by a Windows XP or higher computer through a USB interface using a provided software package that controls all of the receiver’s functions ■ An SD memory card port can be used to store recorded audio ■ Analog composite video output connector ■ CTCSS and DCS squelch operation ■ Two selectable Type N antenna input ports ■ Adjustable analog 45 MHz IF output with 15 MHz bandwidth ■ Triple-conversion receiver exhibits excellent The AR5001D delivers amazing performance in sensitivity terms of accuracy, sensitivity and speed. ■ Powered by 12 volts DC (AC Adapter included), it can be operated as a base Available in both professional and consumer versions, the AR5001D features or mobile unit wide frequency coverage from 40 KHz to 3.15 GHz*, with no interruptions. ■ Professional (government) version is equipped with a standard voice-inversion Developed to meet the monitoring needs of security professionals and monitoring feature government agencies, the AR5001D can be controlled through a PC running Windows XP or higher.
    [Show full text]
  • Boulder Amateur Television Club TV Repeater's REPEATER April, 2020
    TV Rptrs Rptr-39.doc (3/28/2020, kh6htv) p. 1 of 7 Boulder Amateur Television Club TV Repeater's REPEATER April, 2020 BATVC web site: www.kh6htv.com ATN web site: www.amateurtelevisionnetwork.org Jim Andrews, KH6HTV, editor - [email protected] www.kh6htv.com Future Newsletters: If you have contributions for future newsletters, please send them to me. We also welcome news from other ATV groups around the USA. We encourage you to forward this newsletter on to other ATV ham friends in your clubs. Quote from John - WB0CMC: "If you have a good comb generator would that help if you’re having a bad AIR day?" NEW 2ed WEEKLY ATV NET: Due to the pandemic, and everyone being required to stay at home, we are all getting "Cabin Fever" and missing our social interactions with friends and society in general. Thus, the consensus of most of the BATVC members, is that we should hold two ATV nets each week for the duration. Our regular net has been on Thursday afternoons at 3pm local time, with Don, N0YE, as net control. Colin, WA2YUN, has suggested we do the second net on Sunday afternoons. So, let's do it starting this Sunday, the 29th, at 3pm local time. I propose we use a different format with a round table discussion of various topics. Our Thursday nets, seem to be for one ham to talk for several minutes on one or more subjects. For the new Sunday net, let's try making much shorter TV transmissions and expressing our thoughts on a particular subject and then turning it over to another for their comments.
    [Show full text]
  • United States Military Listings
    Monitoring Times Government and Military Frequency/Designation List by Larry Van Horn, N5FPW This list is copyright © 2006 by Larry Van Horn. All rights reserved. This is for the personal use of MT subscribers and readers only. Redistribution of this file in any form or through any other vehicle without permission of the author is strictly prohibited. Absolutely no further distribution of this file via the internet is permitted. UNITED STATES MILITARY LISTINGS Joint Chiefs of Staff Nets High Frequency Global Communications System (HF-GCS) The U.S. Air Force High Frequency (HF) Global Communications System (HF-GCS) is a worldwide network that currently consist of 14 high-power HF stations which provide air/ground HF command and control radio communications between all Department of Defense (DoD) ground agencies, aircraft and ships. Allied military and other aircraft are also provided support in accordance with agreements and international protocols as appropriate. The HF-GCS is not dedicated to any service or command, but supports all authorized users on a traffic precedence basis. On June 1, 1992, the former Global HF System (GHFS) was created by consolidating other U.S. Air Force (USAF) and U.S. Navy (USN) HF networks, including the USAF Global Command and Control System (GCCS), the Navy’s Ship-to-Shore High Command (HICOM) network, and the dedicated Strategic Air Command (SAC) Giant Talk System. The goal of the merger was to develop one worldwide non-dedicated HF network capable of providing Command and Control (C2) HF communications support to all authorized DoD aircraft and ground stations. As of 1 October 2002, the former GHFS network is now known as the HF Global Communications System (HF-GCS).
    [Show full text]
  • Occupied Bandwidth
    Federal Communications Commission § 2.1049 § 2.1049 Measurements required: Occu- used as modulating frequencies, upon a pied bandwidth. sufficient showing of need. However, The occupied bandwidth, that is the any tones so chosen must not be har- frequency bandwidth such that, below monically related, the third and fifth its lower and above its upper frequency order intermodulation products which limits, the mean powers radiated are occur must fall within the ¥25 dB step each equal to 0.5 percent of the total of the emission bandwidth limitation mean power radiated by a given emis- curve, the seventh and ninth order sion shall be measured under the fol- products must fall within the ¥35 dB lowing conditions as applicable: step of the referenced curve and the (a) Radiotelegraph transmitters for eleventh and all higher order products manual operation when keyed at 16 must fall beyond the ¥35 dB step of the dots per second. referenced curve. (b) Other keyed transmitters—when (5) Independent sideband transmit- keyed at the maximum machine speed. ters having two channels—when modu- (c) Radiotelephone transmitters lated by 1700 Hz tones applied simulta- equipped with a device to limit modu- neously to both channels. The input lation or peak envelope power shall be levels of the tones shall be so adjusted modulated as follows. For single side- that the two principal frequency com- band and independent sideband trans- ponents of the radio frequency signal mitters, the input level of the modu- produced are equal in magnitude. lating signal shall be 10 dB greater (d) Radiotelephone transmitters than that necessary to produce rated without a device to limit modulation peak envelope power.
    [Show full text]
  • Federal Communications Commission § 2.1033
    Federal Communications Commission § 2.1033 Commission shall consult with the Of- industry test procedure that was used), fice of the United States Trade Rep- the date the measurements were made, resentative (USTR), as necessary, con- the location where the measurements cerning any disputes arising under an were made, and the device that was MRA for compliance with the Tele- tested (model and serial number, if communications Trade Act of 1988 available). The report shall include (Section 1371–1382 of the Omnibus sample calculations showing how the Trade and Competitiveness Act of 1988). measurement results were converted [64 FR 4995, Feb. 2, 1999, as amended at 66 FR for comparison with the technical re- 27601, May 18, 2001; 69 FR 54034, Sept. 7, 2004] quirements. (7) A sufficient number of photo- CERTIFICATION graphs to clearly show the exterior ap- pearance, the construction, the compo- § 2.1031 Cross reference. nent placement on the chassis, and the The general provisions of this sub- chassis assembly. The exterior views part § 2.901 et seq. shall apply to appli- shall show the overall appearance, the cations for and grants of certification. antenna used with the device (if any), the controls available to the user, and § 2.1033 Application for certification. the required identification label in suf- (a) An application for certification ficient detail so that the name and FCC shall be filed on FCC Form 731 with all identifier can be read. In lieu of a pho- questions answered. Items that do not tograph of the label, a sample label (or apply shall be so noted.
    [Show full text]
  • Chapter 2 Radio Receiver Characteristics
    Source: Communications Receivers: DSP, Software Radios, and Design Chapter 1 Basic Radio Considerations 1.1 Radio Communications Systems The capability of radio waves to provide almost instantaneous distant communications without interconnecting wires was a major factor in the explosive growth of communica- tions during the 20th century. With the dawn of the 21st century, the future for communi- cations systems seems limitless. The invention of the vacuum tube made radio a practical and affordable communications medium. The replacement of vacuum tubes by transistors and integrated circuits allowed the development of a wealth of complex communications systems, which have become an integral part of our society. The development of digital signal processing (DSP) has added a new dimension to communications, enabling sophis- ticated, secure radio systems at affordable prices. In this book, we review the principles and design of modern single-channel radio receiv- ers for frequencies below approximately 3 GHz. While it is possible to design a receiver to meet specified requirements without knowing the system in which it is to be used, such ig- norance can prove time-consuming and costly when the inevitable need for design compro- mises arises. We strongly urge that the receiver designer take the time to understand thor- oughly the system and the operational environment in which the receiver is to be used. Here we can outline only a few of the wide variety of systems and environments in which radio re- ceivers may be used. Figure 1.1 is a simplified block diagram of a communications system that allows the transfer of information between a source where information is generated and a destination that requires it.
    [Show full text]