A Holding and Treatment Furnace the Strikowestofen Group Has Expanded Burnt Directly in the Rotary Drum Furnace

Total Page：16

File Type：pdf, Size：1020Kb

A Holding and Treatment Furnace the Strikowestofen Group Has Expanded Burnt Directly in the Rotary Drum Furnace

SWG_30_AIT_0110 5/19/11 10:37 AM Page 31 I FURNACES www.aluminiumtoday.com A holding and treatment furnace The StrikoWestofen Group has expanded burnt directly in the rotary drum furnace. its activities in aluminium recycling. The continually monitored furnace To meet the demands of aluminium atmosphere guarantees the a high yield. recycling, the new holding and alloy Recycling material such as scrap, chips and furnaces of the H(R) - T type are now dross is melted in a rotary drum furnace in being added. These units have a holding an environmentally-friendly and energy- capacity of 8000 to 20000kg of efficient way. The liquid aluminum is fed aluminium alloy without a melting shaft. via a launder system to the HR - T The H(R) - T is available with or without 10,000/500 holding/alloy furnace supplied a melting ramp due to its modular design. by StrikoWestofen, to carry out possible This type of system is used for holding analysis corrections and to store the metal. alloys which have been melted in separate In the aforementioned case, the furnace large melting units or rotary drum is equipped as a HR - T type with a melting The new StrikoWestofen HR – T 10,000/500 furnaces and for composition adjustment ramp which allows flexibility of operation. of alloys and controlled casting of liquid Here, the required alloying elements are the plant is tilted by means of the metal in launder systems or continuous preheated with a burner, which is hydraulic unit which is equipped with a casting machines. mounted above the ramp before they go proportional valve. The first melting and casting unit was into solution. It is also possible to melt up Continuous casting of the liquid metal developed for a customer in Turkey in to 500kg of aluminum ingots/hr on the then takes place, in the above mentioned partnership with KMF Maschinenfabriken ramp. Porous plugs are installed in the case on to an ingot casting conveyor. The of Villach, Austria. Other projects are bottom of the holding area and have a system can also be used for the currently in preparation. threefold effect: production of billets and rolling slabs. ᔢ One of the product divisions of KMF - - Good mixing of the alloying elements Maschinenfabriken manufactures rotary with the liquid aluminium; Contact drum furnaces which feature a melting - High temperature stability throughout StrikoWestofen GmbH, Fritz-Kotz-Str. 2-4, procedure with a low salt and oxide the bath area; and 51674, Wiehl-Bomig, Germany content. Low temperature carbonisation - Degassing and cleaning of the alloy Tel +49 22 61 7 09 10 Fax +49 22 61 7 09 11 07 gases released from the melting of Once the metal samples taken from the E-Mail [email protected] contaminated materials are subsequently plant meet the required alloy specification, Web www.strikowestofen.com May/June 2011 Aluminium International Today.

Copy Link

Recommended publications

The White Book of STEEL
The white book of STEEL The white book of steel worldsteel represents approximately 170 steel producers (including 17 of the world’s 20 largest steel companies), national and regional steel industry associations and steel research institutes. worldsteel members represent around 85% of world steel production. worldsteel acts as the focal point for the steel industry, providing global leadership on all major strategic issues affecting the industry, particularly focusing on economic, environmental and social sustainability. worldsteel has taken all possible steps to check and confirm the facts contained in this book – however, some elements will inevitably be open to interpretation. worldsteel does not accept any liability for the accuracy of data, information, opinions or for any printing errors. The white book of steel © World Steel Association 2012 ISBN 978-2-930069-67-8 Design by double-id.com Copywriting by Pyramidion.be This publication is printed on MultiDesign paper. MultiDesign is certified by the Forestry Stewardship Council as environmentally-responsible paper. contEntS Steel before the 18th century 6 Amazing steel 18th to 19th centuries 12 Revolution! 20th century global expansion, 1900-1970s 20 Steel age End of 20th century, start of 21st 32 Going for growth: Innovation of scale Steel industry today & future developments 44 Sustainable steel Glossary 48 Website 50 Please refer to the glossary section on page 48 to find the definition of the words highlighted in blue throughout the book. Detail of India from Ptolemy’s world map. Iron was first found in meteorites (‘gift of the gods’) then thousands of years later was developed into steel, the discovery of which helped shape the ancient (and modern) world 6 Steel bEforE thE 18th cEntury Amazing steel Ever since our ancestors started to mine and smelt iron, they began producing steel.
[Show full text]
Implementation of Metal Casting Best Practices
Implementation of Metal Casting Best Practices January 2007 Prepared for ITP Metal Casting Authors: Robert Eppich, Eppich Technologies Robert D. Naranjo, BCS, Incorporated Acknowledgement This project was a collaborative effort by Robert Eppich (Eppich Technologies) and Robert Naranjo (BCS, Incorporated). Mr. Eppich coordinated this project and was the technical lead for this effort. He guided the data collection and analysis. Mr. Naranjo assisted in the data collection and analysis of the results and led the development of the final report. The final report was prepared by Robert Naranjo, Lee Schultz, Rajita Majumdar, Bill Choate, Ellen Glover, and Krista Jones of BCS, Incorporated. The cover was designed by Borys Mararytsya of BCS, Incorporated. We also gratefully acknowledge the support of the U.S. Department of Energy, the Advanced Technology Institute, and the Cast Metals Coalition in conducting this project. Disclaimer This report was prepared as an account of work sponsored by an Agency of the United States Government. Neither the United States Government nor any Agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any Agency thereof. The views and opinions expressed by the authors herein do not necessarily state or reflect those of the United States Government or any Agency thereof.
[Show full text]
Continuous Casting of Steel
1 Chapter 15 in Modeling for Casting and Solidification Processingx, O. Yu, editor, Marcel Dekker, New York, NY, 2001, pp. 499-540. Continuous Casting of Steel Brian G. Thomas Department of Mechanical and Industrial Engineering University of Illinois at Urbana-Champaign 1206 West Green Street Urbana, IL 61801, U.S.A. I. Introduction Continuous casting is used to solidify most of the 750 million tons of steel produced in the world every year. Like most commercial processes, continuous casting involves many complex interacting phenomena. Most previous advances have been based on empirical knowledge gained from experimentation with the process. To further optimize the design and improve the continuous casting process, mathematical models are becoming increasingly powerful tools to gain additional quantitative insight. The best models for this purpose are mechanistic models based on the fundamental laws and phenomena which govern the process, because they are more reliably extended beyond the range of data used to calibrate them. This chapter first presents an overview of the many interacting phenomena that occur during the continuous casting of steel. It then reviews some of the advanced mechanistic models of these phenomena and provides a few examples of the information and insights gained from them. These model applications focus on the mold region, where many continuous casting defects are generated. 2 II. Process Description In the continuous casting process, pictured in Figure 1, molten steel flows from a ladle, through a tundish into the mold. It should be protected from exposure to air by a slag cover over each vessel and by ceramic nozzles between vessels.
[Show full text]
Progress in Net and Near Net Shape Manufacturing of Metallic Components Using the Ohno Continuous Casting (OCC) Process
cie al S nce Fashu SE, J Material Sci Eng 2019, 8:2 ri s te & a E M n f g o i n l e a e n r r i n u g o Journal of Material Sciences & Engineering J ISSN: 2169-0022 ReviewResearch Article Article OpenOpen Access Access Progress in Net and Near Net Shape Manufacturing of Metallic Components using the Ohno Continuous Casting (OCC) Process Simbarashe Everson Fashu* Department of Materials Science and Technology, Harare Institute of Technology, Harare, Zimbabwe Abstract The OCC products have the potential to be used in many industries due to the versatility and low cost of the manufacturing process. The process produces single crystal/unidirectional net, and near net products with excellent surface quality, controlled microstructure and enhanced properties. This article is an overview of the progress in OCC process since its inception in manufacturing of metallic components. The process, product range, potential and limitations are outlined. The process is now commercialized; and products for electronics, medical, joining, hard facing, shape memory, etc., can be fabricated. However, according to expectations, its use is still limited and potential applications including fabrication of structural materials for aerospace and automobile applications, production of large size ingots, purification of alloys and silicon crystal growth remain to be explored. Keywords: Continuous casting; Crystal; Directional; Heated mold flow, microstructures, segregation are still to be developed and applied in order to improve the process. Introduction The OCC Process Polycrystalline metals/alloys are always of either limited strength or ductility since strengthening is accompanied by loss of ductility The technique in these materials [1-3].
[Show full text]
Dross Removal Equipment STEEL INDUSTRY PRODUCTS
Dross removal equipment STEEL INDUSTRY PRODUCTS L-TEC Steel Industry Products offer the ideal equipment for low-cost deburring of continuous cast slabs and blooms. Mechanical deburring of cross cut slabs provides many advantages. ADVANTAGES INCLUDE: � Lowest initial and installation cost, lowest operating cost (electric and hydraulic), and lowest maintenance compared to competitive equipment � Four edged blades extend service life and allow the operator to use one side for narrow and one side for wide slabs � Tilting deburring blades that remove burr from cross cut ends of slabs � Reduction of time and cost associated with the handling of hand scar ng or other removal methods � Possibility to interface with mill hydraulics, PLC, and computer systems � Consistent steel quality � Low noise, simple operation L-TEC’s tilting dross removal blade and dross removal table TILTING DROSS BLADE. eliminate cutting dross problems, as well as additional handling and hand scar ng operations required to remove The dross blade is used to remove the dross/slag from the cutting dross (also called kerf, burr, beard, or slag) from both ends of a ame-cut continuous cast slab. The machine continuous-cast or other torch cut product. normally mounts between rolls in the caster run-out line, and the double-edged blade is used for front- and tail-end Dross removal equipment is typically installed in the dross removal. The dross is sheared by the blade as the slab continuous casting line downstream of the cut-off machine. passes over the edge. The dross blade effectively eliminates the cutting dross beneath both ends of slabs.
[Show full text]
Establishment of Special Steel Production System at Kakogawa
Establishment of Special Steel Production System at Kakogawa Works -Construction of No.3 Secondary Refining Equipment and No.6 Continuous Caster- Yasumasa YOSHIDA＊1, Hideya OKADA＊1, Hiroaki SAKAI＊1, Hiroyuki ONODA＊2, Dr. Takehiro NAKAOKA＊3 *1 Steelmaking Department, Kakogawa Works, Iron & Steel Business *2 Steelmaking Development Department, Research & Development Laboratory, Iron & Steel Business *3 Mechanical Engineering Research Laboratory, Technical Development Group Kobe Steel shut down the operation of the ironmaking been produced at Kobe Works. The department and steelmaking process at Kobe Works in October established a technology for adjusting nitrogen 2017, and in November 2017, this upstream process during molten steel processing, along with a was consolidated at Kakogawa Works. Prior to this, by technology for operating a 5-strand continuous January 2017, the Steelmaking Department of Kakogawa bloom caster, and inaugurated a one-base system Works had established a special-steel production system for producing crude steel at Kakogawa Works in for wire rods by installing No.3 secondary refining November 2017, as planned. equipment (2LF, 4RH) and a No.6 continuous caster. A This paper describes the features and quality challenge in designing the new process was to produce design concepts of No.3 molten steel treating small lots of special steel with high productivity, high equipment, including a No.4 Ruhrstahl-Heraeus yield and high quality at Kakogawa Works, which has degassing apparatus (4RH) and No.2 vessel furnace a large heat size. In order to solve this problem, cutting (2LF), as well as those of the No.6 continuous caster edge technologies were introduced in the upstream (6CC), and reports on their operational status after equipment.
[Show full text]
Manufacturing Technology I Unit I Metal Casting
MANUFACTURING TECHNOLOGY I UNIT I METAL CASTING PROCESSES Sand casting – Sand moulds - Type of patterns – Pattern materials – Pattern allowances – Types of Moulding sand – Properties – Core making – Methods of Sand testing – Moulding machines – Types of moulding machines - Melting furnaces – Working principle of Special casting processes – Shell – investment casting – Ceramic mould – Lost Wax process – Pressure die casting – Centrifugal casting – CO2 process – Sand Casting defects. UNIT II JOINING PROCESSES Fusion welding processes – Types of Gas welding – Equipments used – Flame characteristics – Filler and Flux materials - Arc welding equipments - Electrodes – Coating and specifications – Principles of Resistance welding – Spot/butt – Seam – Projection welding – Percusion welding – GS metal arc welding – Flux cored – Submerged arc welding – Electro slag welding – TIG welding – Principle and application of special welding processes – Plasma arc welding – Thermit welding – Electron beam welding – Friction welding – Diffusion welding – Weld defects – Brazing – Soldering process – Methods and process capabilities – Filler materials and fluxes – Types of Adhesive bonding. UNIT III BULK DEFORMATION PROCESSES Hot working and cold working of metals – Forging processes – Open impression and closed die forging – Characteristics of the process – Types of Forging Machines – Typical forging operations – Rolling of metals – Types of Rolling mills – Flat strip rolling – Shape rolling operations – Defects in rolled parts – Principle of rod and wire drawing – Tube drawing – Principles of Extrusion – Types of Extrusion – Hot and Cold extrusion – Equipments used. UNIT IV SHEET METAL PROCESSES Sheet metal characteristics – Typical shearing operations – Bending – Drawing operations – Stretch forming operations –– Formability of sheet metal – Test methods – Working principle and application of special forming processes – Hydro forming – Rubber pad forming – Metal spinning – Introduction to Explosive forming – Magnetic pulse forming – Peen forming – Super plastic forming.
[Show full text]
History of Metal Casting Fathi Habashi
Laval University From the SelectedWorks of Fathi Habashi August, 2007 History of Metal Casting Fathi Habashi Available at: https://works.bepress.com/fathi_habashi/438/ History of Metal Casting Fathi Habashi Department of Mining, Metallurgical, and Materials Engineering Laval University, Quebec City, Canada [email protected] metallurgy History of Metal Casting—Part 1 by Fathi Habashi, Department of Mining, Metallurgical, and Materials Engineering, Laval University believe that my work would surely be almost a seed without fruit and that I would fail in that cause which disposed me to satisfy your request I to write and form this work if, while labouring on it, 1 did not tell you of the art of casting, since it is a necessary means to very many ends. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed… it is a proﬁtable and skilful art and in large part delightful. [BIRINGUCCIO, IN PIROTECHNIA, 1540] Introduction The history of metal casting is the history of metal- lurgy. Metals produced in a furnace are melted and cast to form useful objects, whether a piece of jewelry, an agri- cultural tool, or a weapon. Objects made of gold, silver, copper, bronze, brass, tin, lead, and iron conserved in museums are a testimony to the cleverness of the ancient metal workers.
[Show full text]
New Technology for Continuous Casting Machine
New Technology for Continuous Casting Machine Tomonori NISHIOKA＊1, Fumiki ASANO＊1, Hiroshi KAWAGUCHI＊2 *1 Heavy Machinery Department, Industrial Machinery Division, Machinery Business *2 Industrial Machinery Engineering Division, SHINKO TECHNO ENGINEERING CO., LTD In pursuit of high productivity, energy saving, steel- supporting roll stand are required to have structures type versatility, and more stringent quality, each with high rigidity and to move without backlash so engineering company of steel making equipment has made as to allow each slab to be accurately drawn along a variety of unique development and improvements of the track even under high-temperature high-load continuous casting machines since its full-scale practical conditions. applications in the 1960s. Kobe Steel has newly developed Kobe Steel has conducted development and an optimal support mechanism for a large tundish, improvement in various manners to meet customer and a highly precise weighing device for tundish cars, requests, not only for apparatus reliability but also which are closely related to safety and workability. In slab quality. This paper introduces the technologies addition, the company has newly developed a structure, adopted to the continuous casting equipment for capable of maintaining high rigidity and movements producing special steel blooms that was delivered to without backlash for an extended period of time, for Kobe Steel's Kakogawa Works in January 2017. the mold oscillator and supporting roll stand, which can significantly affect the quality of cast blooms. This 1. Tundish car paper introduces these technologies, which have been employed in the continuous bloom casting equipment 1.1 Role of tundish car for special steel-equipment that was delivered to Kobe Steel's Kakogawa Works in January 2017.
[Show full text]
Continuous Casting
68 9 CONTINUOUS CASTING papers will be presented by Primetals Technologies specialists at the ESTAD Congress covering the topics of slab, billet and bloom casting in addition to automation, logistics and modernization solutions. Metals Magazine 1/2015 | Technology | Continuous Casting 69 Through the “ modernization of our continuous slab-casting machine we have acquired one of the most advanced casters of its kind in the world. This increases our production potential.” Company manager, Acroni, Slovenia Metals Magazine 1/2015 | Technology | Continuous Casting 70 State-of-the-art casting platform at voestalpine Stahl, Austria THE CONTINUOUS SLAB CASTER IN THE TWENTY-FIRST CENTURY Principal author: Dr. Martin Hirschmanner; Paper number: 278 The first continuous casting machine built by VAI in the In recent years, the combination of mechanical equipment year 1968 already had several features that are still state of with hydraulic, electrical and automation systems has the art today. These include a straight mold, a continuous transformed the casting machine into a complex mecha- bending and unbending curve, and small, intermediately tronic system. The deep integration of all disciplines is supported rollers for minimum bulging. It might be as- essential for casting sophisticated steel grades with per- sumed that the mechanical development of the continu- fect process control, while still maintaining low operational ous slab caster was completed a long time ago. However, costs. The ongoing fourth industrial revolution will also the opposite is true. Modern design methods make it influence the design of continuous casting machines in possible to engineer a substantially improved caster that a practical way that offers major advantages to plant meets the ever-increasing demands of plant operators.
[Show full text]
Solidification Control in Continuous Casting of Steel
Sadhana, Vol. 26, Parts 1 & 2, February–April 2001, pp. 179–198. © Printed in India Solidification control in continuous casting of steel S MAZUMDAR and S K RAY R&D Centre for Iron and Steel, Steel Authority of India Ltd (SAIL), Ranchi, India e-mail: [email protected] Abstract. An integrated understanding of heat transfer during solidification, friction/lubrication at solid–liquid interface, high temperature properties of the solidifying shell etc. is necessary to control the continuous casting process. The present paper elaborates upon the knowledge developed in the areas of initial shell formation, mode of mould oscillation, and lubrication mechanism. The effect of these issues on the caster productivity and the quality of the product has been discussed. The influence of steel chemistry on solidification dynamics, particularly with respect to mode of solidification and its consequence on strength and ductility of the solidifying shell, has been dealt with in detail. The application of these basic principles for casting of stainless steel slabs and processing to obtain good quality products have been covered. Keywords. Continuous casting; early solidification; mould oscillation; lubrication; mode of solidification; strength and ductility of shell; microsegregation. 1. Introduction Solidification in continuous casting (CC) technology is initiated in a water-cooled open-ended copper mould. The steel shell which forms in the mould contains a core of liquid steel which gradually solidifies as the strand moves through the caster guided by a large number of roll pairs. The solidification process initiated at meniscus level in the mould is completed in secondary cooling zones using a combination of water spray and radiation cooling.
[Show full text]
Aluminum Foundry Products
ASM Handbook, Volume 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials Copyright © 1990 ASM International® ASM Handbook Committee, p 123-151 All rights reserved. DOI: 10.1361/asmhba0001061 www.asminternational.org Aluminum Foundry Products Revised by A. Kearney, Avery Kearney & Company Elwin L. Rooy, Aluminum Company of America ALUMINUM CASTING ALLOYS are wrought alloys. Aluminum casting alloys cast aluminum alloys are grouped according the most versatile of all common foundry must contain, in addition to strengthening to composition limits registered with the alloys and generally have the highest cast- elements, sufficient amounts of eutectic- Aluminum Association (see Table 3 in the ability ratings. As casting materials, alumi- forming elements (usually silicon) in order article "Alloy and Temper Designation Sys- num alloys have the following favorable to have adequate fluidity to feed the shrink- tems for Aluminum and Aluminum Al- characteristics: age that occurs in all but the simplest cast- loys"). Comprehensive listings are also • Good fluidity for filling thin sections ings. maintained by general procurement specifi- The phase behavior of aluminum-silicon • Low melting point relative to those re- cations issued through government agencies compositions (Fig. 1) provides a simple quired for many other metals (federal, military, and so on) and by techni- • Rapid heat transfer from the molten alu- eutectic-forming system, which makes pos- cal societies such as the American Society sible the commercial viability of most high- minum to the mold, providing shorter for Testing and Materials and the Society of casting cycles volume aluminum casting. Silicon contents, Automotive Engineers (see Table 1 for ex- • Hydrogen is the only gas with apprecia- ranging from about 4% to the eutectic level amples).
[Show full text]