Macquisition Quickstart Guide-V2020r1
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
Application Note
Application Note Using Apple’s Target Disk Mode to access a Mac’s internal drive as a Source drive (For use with Thunderbolt or FireWire) with the Forensic Falcon™ or Talon® Ultimate Introduction: This document provides instructions on how to access a Mac’s internal drive to be used as a Source drive on the Forensic Falcon or Talon Ultimate using either the Mac’s on-board Thunderbolt or FireWire port. This method will allow the Falcon or Talon Ultimate to see the Mac’s internal drive as a Source drive. The drive can then be imaged or hashed using the Falcon or Talon Ultimate. The Talon Ultimate FireWire ports can be enabled with purchase of the FireWire option. The Falcon FireWire ports are already enabled and do not require any option purchased. Sections: I – Requirements II – Enabling Target Disk Mode on the Mac III – What to Expect on the Falcon/Talon Ultimate Section I – Requirements: A Forensic Falcon or Talon Ultimate (the Talon Ultimate must have the FireWire option purchased and enabled. A Mac with: o At least one native Thunderbolt/Thunderbolt 2 or FireWire port o Target Disk Mode support (If you are unsure whether the Mac supports Target Disk Mode, please contact Apple). For Macs with Thunderbolt/Thunderbolt 2 – Apple’s Thunderbolt to FireWire adapter and a FireWire 800 to 800 cable (one is included with the Falcon) . For Macs with FireWire 800 – A FireWire 800 to 800 cable (one is included with the Falcon, but not with the Talon Ultimate) . For Macs with FireWire 400 – A FireWire 400 to 800 adapter with a FireWire 800 to 800 cable (one FireWire 800 to 800 cable is included with the Falcon but not with the Talon Ultimate) or a FireWire 400 to 800 cable. -
Power Mac G4 (Digital Audio): Setting up (Manual)
Setting Up Your Power Mac G4 Includes setup and expansion information for Power Mac G4 and Macintosh Server G4 computers K Apple Computer, Inc. © 2001 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors. Apple Computer, Inc. 1 Infinite Loop Cupertino, CA 95014-2084 408-996-1010 http://www.apple.com Apple, the Apple logo, AppleShare, AppleTalk, FireWire, the FireWire logo, Mac, Macintosh, the Mac logo, PlainTalk, Power Macintosh, QuickTime, and Sherlock are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. AirPort, the Apple Store, Finder, iMovie, and Power Mac are trademarks of Apple Computer, Inc. PowerPC and the PowerPC logo are trademarks of International Business Machines Corporation, used under license therefrom. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. © 1992–1997 Dolby Laboratories, Inc. All rights reserved. Other company and product names mentioned herein are trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. -
Setting up Your Power Mac G4 Includes Setup and Expansion Information for Power Mac G4 Abs Macintosh Server G4 Computers
Setting Up Your Power Mac G4 Includes setup and expansion information for Power Mac G4 abs Macintosh Server G4 computers Setting Up Your Power Mac G4 Includes setup and expansion information for Power Mac G4 abs Macintosh Server G4 computers Apple Computer, Inc. © 2000 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the "keyboard" Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors. Apple Computer, Inc. 1 Infinite Loop Cupenino, CA 95014-2084 408-996-1010 http://www.apple.com Apple, the Apple logo, AppleShare, AppleTalk, FireWire, the FireWire logo, Mac, Macintosh, the Mac logo, PlainTalk, Power Macintosh, and QuickTime are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. AirPort, the Apple Store, Finder, iMovie, iTools, Power Mac, and Sherlock are trademarks of Apple Computer, Inc. PowerPC and the PowerPC logo are trademarks of International Business Machines Corporation, used under license therefrom. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories, Confidential Unpublished Works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved. Other company and product names mentioned herein are trademarks of their respective companies. -
Mac Keyboard Shortcuts Cut, Copy, Paste, and Other Common Shortcuts
Mac keyboard shortcuts By pressing a combination of keys, you can do things that normally need a mouse, trackpad, or other input device. To use a keyboard shortcut, hold down one or more modifier keys while pressing the last key of the shortcut. For example, to use the shortcut Command-C (copy), hold down Command, press C, then release both keys. Mac menus and keyboards often use symbols for certain keys, including the modifier keys: Command ⌘ Option ⌥ Caps Lock ⇪ Shift ⇧ Control ⌃ Fn If you're using a keyboard made for Windows PCs, use the Alt key instead of Option, and the Windows logo key instead of Command. Some Mac keyboards and shortcuts use special keys in the top row, which include icons for volume, display brightness, and other functions. Press the icon key to perform that function, or combine it with the Fn key to use it as an F1, F2, F3, or other standard function key. To learn more shortcuts, check the menus of the app you're using. Every app can have its own shortcuts, and shortcuts that work in one app may not work in another. Cut, copy, paste, and other common shortcuts Shortcut Description Command-X Cut: Remove the selected item and copy it to the Clipboard. Command-C Copy the selected item to the Clipboard. This also works for files in the Finder. Command-V Paste the contents of the Clipboard into the current document or app. This also works for files in the Finder. Command-Z Undo the previous command. You can then press Command-Shift-Z to Redo, reversing the undo command. -
About the Power Mac G4 Cube (Manual)
About the Power Mac G4 Cube Includes setup and expansion information for Power Mac G4 Cube computers K Apple Computer, Inc. © 2000 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors. Apple Computer, Inc. 1 Infinite Loop Cupertino, CA 95014-2084 408-996-1010 http://www.apple.com Apple, the Apple logo, AppleShare, AppleTalk, FireWire, the FireWire logo, Mac, Macintosh, the Mac logo, Power Macintosh, and QuickTime are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. AirPort, the Apple Store, Finder, iMovie, iTools, Power Mac, and Sherlock are trademarks of Apple Computer, Inc. PowerPC and the Power PC logo are trademarks of International Business Machines Corporation, used under license therefrom. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. © 1992–1997 Dolby Laboratories, Inc. All rights reserved. Other company and product names mentioned herein are trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. -
Chapter 1. Origins of Mac OS X
1 Chapter 1. Origins of Mac OS X "Most ideas come from previous ideas." Alan Curtis Kay The Mac OS X operating system represents a rather successful coming together of paradigms, ideologies, and technologies that have often resisted each other in the past. A good example is the cordial relationship that exists between the command-line and graphical interfaces in Mac OS X. The system is a result of the trials and tribulations of Apple and NeXT, as well as their user and developer communities. Mac OS X exemplifies how a capable system can result from the direct or indirect efforts of corporations, academic and research communities, the Open Source and Free Software movements, and, of course, individuals. Apple has been around since 1976, and many accounts of its history have been told. If the story of Apple as a company is fascinating, so is the technical history of Apple's operating systems. In this chapter,[1] we will trace the history of Mac OS X, discussing several technologies whose confluence eventually led to the modern-day Apple operating system. [1] This book's accompanying web site (www.osxbook.com) provides a more detailed technical history of all of Apple's operating systems. 1 2 2 1 1.1. Apple's Quest for the[2] Operating System [2] Whereas the word "the" is used here to designate prominence and desirability, it is an interesting coincidence that "THE" was the name of a multiprogramming system described by Edsger W. Dijkstra in a 1968 paper. It was March 1988. The Macintosh had been around for four years. -
NCSA Telnet for the Macintosh User's Guide
NCSA Telnet for the Macintosh User’s Guide Version 2.6 • October 1994 National Center for Supercomputing Applications University of Illinois at Urbana-Champaign Contents Introduction Features of NCSA Telnet v Differences between Version 2.5 and Version 2.6 v New Features in Version 2.6 v Discontinued Features vi Bugs Fixed from Version 2.5 vi System Requirements vi Notational Conventions vi 1 Getting Started Installation Note 1-1 Beginning an NCSA Telnet Session 1-1 Opening and Closing a Connection 1-2 Opening a Connection 1-2 Logging on to Your Host 1-3 Setting the BACKSPACE/DELETE Key 1-3 Setting a VT Terminal Type 1-3 Emulating the VT Terminal Keyboard 1-4 Closing a Connection 1-4 Copying, Pasting, and Printing 1-5 Copy and Paste from the Edit Menu 1-5 Print from the File Menu 1-5 Ending an NCSA Telnet Session 1-6 2 Configuration Global Preferences 2-1 New Configuration System in Version 2.6 2-3 Default Configuration Records 2-3 Editing Configuration Records 2-3 Editing Terminal Configuration Records 2-4 Editing Session Configuration Records 2-5 Changing Configuration after Session Connected 2-9 Saved Sets 2-13 Saving a Set 2-14 Using a Saved Set 2-14 Loading a Saved Set 2-15 Macro Definitions 2-15 Reverting to Previous Macro Definitions 2-16 Saving Macros 2-16 3 Advanced Features Cursor Positioning with the Mouse 3-1 Multiple Connections 3-1 Opening More Than One Connection 3-1 Moving between Connections 3-1 Rules for Session Names 3-2 The Connections Menu 3-2 Naming Windows 3-2 Checking Session Status 3-2 Aborting Connection Attempts -
RECON-IMAGER-Manual.Pdf
RECON IMAGER Manual 1.Introduction Version 4.0.5 RECON IMAGER was developed by SUMURI to provide the digital forensic practitioner with a bootable imaging utility that supports all modern Macintosh computers with Intel processors. This is accomplished via three macOS based boot environments that have been modified to ensure that there are no writes to internal or externally attached media. Additionally, RECON IMAGER helps the practitioner to easily identify Apple File System (APFS) container disks and volumes, FileVault, Fusion and other Core Storage volumes. RECON IMAGER has been designed to get as much data as possible to include the Apple Extended Attributes and Local Time Machine Snapshots (APFS Snapshots). In addition to creating forensic images of physical disks and/or volumes, RECON IMAGER can also image Mac RAM without the need for an administrator password within RECON IMAGER’s boot environment. RECON IMAGER also supports imaging Macs with T2 Security Chipsets via Target Disk Mode or disabling Secure Boot via the Mac’s Recovery Mode. Copyright © 2010-2020 SUMURI LLC. All rights reserved. 1 RECON IMAGER Manual 2. Version Comparisons There are two versions of RECON IMAGER – Standard and PRO. RECON IMAGER (standard) RECON IMAGER (standard) is based on macOS. Since it is based on macOS it natively boots Intel Macs. It also supports Apple proprietary technology such as Apple File System (APFS) container disks and volumes, FileVault, Fusion and other Core Storage volumes. RECON IMAGER includes the option to image logically which allows an examiner to import Apple data into forensic tools that do not natively support proprietary Apple file systems. -
Xserve G5 User's Guide (Manual)
Xserve G5 User’s Guide Includes setup, expansion, and hardware specifications for Xserve G5 K Apple Computer, Inc. © 2004 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. Your rights to the software are governed by the accompanying software license agreement. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors. Apple 1 Infinite Loop Cupertino, CA 95014-2084 408-996-1010 www.apple.com Apple, the Apple logo, FireWire, the FireWire logo, iBook, Mac, Macintosh, Mac OS, PowerBook, QuickTime, and Xserve are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. PowerPC and the PowerPC logo are trademarks of International Business Machines Corporation, used under license therefrom. This product includes software developed by the University of California, Berkeley, and its contributors. Other company and product names mentioned herein are trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. Apple assumes no responsibility with regard to the performance or use of these products. Simultaneously published in the United States and Canada. -
Pro Tools 7.0 Keyboard Shortcuts (For Pro Tools|HD, Pro Tools LE, and Pro Tools M-Powered Systems on Macintosh)
Pro Tools 7.0 Keyboard Shortcuts (for Pro Tools|HD, Pro Tools LE, and Pro Tools M-Powered Systems on Macintosh) For increased operational speed and ease-of-use, there are many Pro Tools keyboard shortcuts to give you fast access to a wide va- riety of tasks. This guide lists these keyboard shortcuts. The shortcuts are grouped by functional area for your added convenience and quick reference. Menu commands that have a keyboard shortcut display their keyboard shortcut on-screen, to the right of the menu command. Conventions Used in This Guide Digidesign guides use the following conventions to indicate menu choices and key commands: Table 1. Global keyboard shortcuts Convention Action File > Save Session Choose Save Session from the File menu. Command+N Hold down the Command (Apple) key and press the N key Option+Plus/Minus (+/–) keys Hold down the Option key and press the Plus (+) or Minus (–) key (on numeric keypad or QWERTY, as noted). Command-click Hold down the Command key and click the mouse button. Global Keyboard Shortcuts Table 2. Global keyboard shortcuts Task Shortcut Change parameters on all similar channel strips Option+applicable function (applicable functions listed below) Change parameter on all selected similar channel Option+Shift+applicable function (applicable functions listed directly below) strips Applicable functions: Automation mode • Monitor mode • playlist enables • record, solo and mute enables • record and solo safes • inserting plug-ins • I/O, bus, send assignment • volume/peak indicator • extend Edit or Timeline -
Mac OS for Quicktime Programmers
Mac OS For QuickTime Programmers Apple Computer, Inc. Technical Publications April, 1998 Apple Computer, Inc. Apple, the Apple logo, Mac, LIMITED WARRANTY ON MEDIA © 1998 Apple Computer, Inc. Macintosh, QuickDraw, and AND REPLACEMENT All rights reserved. QuickTime are trademarks of Apple ALL IMPLIED WARRANTIES ON THIS No part of this publication or the Computer, Inc., registered in the MANUAL, INCLUDING IMPLIED software described in it may be United States and other countries. WARRANTIES OF reproduced, stored in a retrieval The QuickTime logo is a trademark MERCHANTABILITY AND FITNESS system, or transmitted, in any form of Apple Computer, Inc. FOR A PARTICULAR PURPOSE, ARE or by any means, mechanical, Adobe, Acrobat, Photoshop, and LIMITED IN DURATION TO NINETY electronic, photocopying, recording, PostScript are trademarks of Adobe (90) DAYS FROM THE DATE OF or otherwise, without prior written Systems Incorporated or its DISTRIBUTION OF THIS PRODUCT. permission of Apple Computer, Inc., subsidiaries and may be registered in Even though Apple has reviewed this except in the normal use of the certain jurisdictions. manual, APPLE MAKES NO software or to make a backup copy Helvetica and Palatino are registered WARRANTY OR REPRESENTATION, of the software or documentation. trademarks of Linotype-Hell AG EITHER EXPRESS OR IMPLIED, WITH The same proprietary and copyright and/or its subsidiaries. RESPECT TO THIS MANUAL, ITS notices must be affixed to any ITC Zapf Dingbats is a registered QUALITY, ACCURACY, permitted copies as were affixed to trademark of International Typeface MERCHANTABILITY, OR FITNESS the original. This exception does not Corporation. FOR A PARTICULAR PURPOSE. AS A allow copies to be made for others, RESULT, THIS MANUAL IS Simultaneously published in the whether or not sold, but all of the DISTRIBUTED “AS IS,” AND YOU United States and Canada. -
WELCOME to MAC101! Instructor: Debbie Kritikos, Elementary Technology Coach [email protected]
WELCOME TO MAC101! Instructor: Debbie Kritikos, Elementary Technology Coach [email protected] 1. BASIC FEATURES http://www.apple.com/support/mac101/tour/ a. Off/On i. Mac minis - back right on older ones; right side on new ones ii. MacBooks -as soon as you press the power button, hold in the ALT/OPTION key (lower left) – this will allow you to choose between Mac or Windows (there will be an up arrow pointing to Windows); use the left arrow(←) key to select MAC, then press ENTER iii. Sign on with your WHSD user name and password and hit ENTER on keyboard OR click LOG IN (Mac OS will take slightly longer to load than Windows) iv. Force Quit (Same as a Control/Alt/Delete in Windows): APPLE > FORCE QUIT > All programs will appear in window – select one that does not respond > FORCE QUIT v. Volume – Mac mini (SYSTEM PREFERENCES > SOUND > adjust slider at bottom); MacBook (top row right keys F10-mute, F11-decrease, F12-increase or in System Tray) vi. Eject a disk 1. Press Eject key on MacBook (top right with triangle with Horizontal line under it) 2. F12 (hold for few seconds) 3. COMMAND-E 4. CONTROL > click on drive icon > EJECT “AUDIO CD” 5. Drag the icon for the disk drive to Trash icon in Dock vii. Turn off: APPLE > SHUT DOWN OR CONTROL-EJECT > SHUT DOWN OR press and release the power button > SHUT DOWN b. Track pad on the MacBook (no mouse) i. APPLE (if System Preferences not in the dock) > SYSTEM PREFERENCES > TRACKPAD (set up options) 1.