Regrouting Tile As Grout Gets Older, It Tends to Chip Away. This Allows

Total Page：16

File Type：pdf, Size：1020Kb

Regrouting Tile As Grout Gets Older, It Tends to Chip Away. This Allows

• QUIKRETE® Multi-Purpose Thin-Set • QUIKRETE® Polymer-Modified Tile Grout • Putty Knife • Toothbrush • Hammer • Straight bar or chisel • Trowel • Plastic Sheet Regrouting Tile As grout gets older, it tends to chip away. This allows water to seep behind the tile and, eventually, it will loosen. When regrouting is necessary, proceed as follows: 1. With a putty knife, dig out the old grout. Remove all loose material, then dampen the joint. 2. Apply the new grout, working it into the joints with a toothbrush. 3. Smooth the grout with your finger. Be sure to clean off any excess from the tile immediately. Replacing Tile In those cases where tile is damaged beyond repair, your only choice is to replace it. Use the following technique: 1. If only a few random tiles must be replaced, use a hammer to break them up. Remove all the pieces of tile and grout. 2. If you are replacing an entire section of tile, use a hammer and a straight bar or chisel to loosen the top tile. It should work free by tapping lightly with the hammer. Work down and remove the rest of the tile in the same manner. 3. Once the old tile has been removed, use the putty knife to completely remove the old adhesive. On larger areas, it is a good idea to sand the entire surface with a belt sander after scraping with the knife. 4. Apply the mortar and set the new tile. 5. Wait a day or two for the mortar to set, then remove the spacers, dampen the joints and apply the grout. For Best Results • If you are working in a shower or bathtub enclosure, protect the tub by covering it with a sheet of plastic to prevent tile chips from scratching it. • When working around fixtures with a hammer and straight bar or chisel, be careful to avoid damaging the fixtures. .

Copy Link

Recommended publications

Minimizing Grout Shading
TB20 MINIMIZING GROUT SHADING CAUSES w Mix grout thoroughly by hand or with a low RPM (300 rpm) Inconsistent grout color is a condition where colored grout dries power mixer. to its expected color in some areas, a darker color in some areas w Always mix the grout powder into the liquid. and varying shades in-between. The main cause for this variation w Mix grout to a stiff, creamy, paste-like consistency. in color is uneven drying of the Portland cement in the grout. w Allow grout to rest (slake) once mixed, then remix. There are jobsite conditions and factors which create the conditions for uneven drying and improper cement hydration. w Discard grout when it becomes too stiff to work. Inconsistent grout color is not considered a manufacturing defect w Use the same procedure to grout all areas. due to the inconsistent nature of Portland cement. Portland w Use a rubber grout float to remove grout from tile during cement is a natural product, mined from the ground, with inherent installation. properties which cannot be completely controlled. w Allow grout to firm in the joint before any further cleaning is to Colored grouts, like concrete, are a combination of Portland be done. Porcelain tile will require more time. Grout is firm cement and an inert aggregate. It is not uncommon for concrete when it can only slightly be indented when pressed hard with driveways, or sidewalks to show discoloration and inconsistent your fingernail. color. Like colored grout, this is mainly due to the uneven drying w Use as little water as possible for clean-up.
[Show full text]
A Masonry Wall and Slide Repair Using Soil Nails and Rock Dowels Drew Gelfenbein, Christopher Benda, PE and Peter Ingraham, PE 1.0 Background
A Masonry Wall and Slide Repair Using Soil Nails and Rock Dowels Drew Gelfenbein, Christopher Benda, PE and Peter Ingraham, PE 1.0 Background In the middle of August 2003, Vermont experienced several days of very heavy rains which precipitated a slide failure on Vermont Route 73 in Forest Dale at approximately mile marker 6.36. A blocked culvert on the south side of VT 73 caused an overflow of water across the road surface and over an asphalt and wood curb down an embankment. This resulted in a significant amount of erosion, undermining of the road surface (Figure 1) and a washout of a timber cribbing retaining structure Figure 1: Undermining of north side of VT 73 located on the top of a mortared masonry wall (Figure 2). in Forest Dale. In the project area, VT 73 is constructed on a retained embankment in steep terrain formed in sub-vertically dipping schistose meta-greywacke. The embankment along a valley sidewall was originally built by constructing masonry retaining structures to span between a series of rock knobs. Soils mantling the rock in the valley consist of dense glacial till. The natural terrain was incised by the Neshobe River, which occupies the valley floor approximately 80 feet below and 100 feet north of the project retaining walls. After site visits by Vermont Agency of Transportation (VTrans) staff, it was decided that the laid up masonry wall immediately west of the slide area was also in desperate need of repair. The laid up masonry wall (Figure 3) was observed to have broken and missing blocks.
[Show full text]
Non-Shrink Precision Grout 1585-00
NON-SHRINK PRECISION GROUT DIVISION 3 2 PRODUCT NO. 1585-00, -02 03 62 00 Non-Shrink Grouting PRODUCT DESCRIPTION QUIKRETE Non-Shrink Precision Grout is a high-strength, non-metallic, non-shrink grout designed for precision grouting and general construction applications. It can be mixed to a fluid, flowable, or plastic consistency requiring only the addition of clean water. PRODUCT USE Typical applications for QUIKRETE Non-Shrink Precision Grout include grouting of: • All types of machinery • Steel columns • Bearing plates PHYSICAL/CHEMICAL • Precast concrete QUIKRETE Non-Shrink Precision Grout complies with the physical • Other anchoring or void filling conditions that require high strength requirements of ASTM C1107 and CRD 621. Typical results obtained The non-shrink characteristics of Non-Shrink Precision Grout make it for QUIKRETE Non-Shrink Precision Grout, when tested at 73.5 ºF ± stable and capable of handling high load transfers. 3.5 ºF (23.0 ºC ± 2.0 ºC), are shown in Table 2. SIZES INSTALLATION • 50 lb (22.6 kg) bags SURFACE PREPARATION Wear the appropriate personal protective equipment. All grouting YIELD surfaces should be clean and free of foreign substances including 3 • Each 50 lb (22.6 kg) bag will yield 0.45 ft (12.7 L) at flowable corrosion, if present on steel. Remove all spalled areas and areas of consistency unsound concrete. Preparation work done on the grouting surfaces should be completed by high pressure water blast, breaker, hammer, or TECHNICAL DATA other appropriate mechanical means to obtain a properly prepared APPLICABLE STANDARDS surface. Saturate repair area with clean water before grouting to ensure • ASTM C109 Standard Test Method for Compressive Strength of SSD condition.
[Show full text]
Chapter 15 – Table of Contents
Bridge Maintenance Course Series Reference Manual Chapter 15 – Table of Contents Chapter 15 - Channel and Waterway ....................................................................................... 15-1 15.1 Identifying Scour and Erosion – Waterway Mechanics ..................................................... 15-1 15.2 Preventive and Basic Maintenance for Channels and Waterway ..................................... 15-5 15.2.1 Debris Removal ............................................................................................................... 15-5 15.2.2 Vegetation Removal ........................................................................................................ 15-8 15.3 Repair and Rehabilitation of Channel and Waterway ....................................................... 15-8 15.3.1 Placement of Riprap and Gabions ................................................................................ 15-11 15.2.2 Tremie Concrete ........................................................................................................... 15-19 15.2.3 Grout Bag Placement .................................................................................................... 15-20 15.2.4 Sheet Piling.................................................................................................................... 15-24 15.2.5 Articulated Block ........................................................................................................... 15-25 15.3 Chapter 15 Reference List ...............................................................................................
[Show full text]
Testing Machine for Expansive Mortar R
Testing machine for Expansive Mortar R. A. V. Silva 1 1Departamento de Engenharia de Materiais – Universidade Federal de Campina Grande – PB _____________________________________________________________________________________ Abstract: The correct evaluation of a material property is fundamental to, on their application; they met all expectations that were designed for. In development of an expansive cement for ornamental rocks purpose, was denoted the absence of methodologies and equipments to evaluate the expansive pressure and temperature of expansive cement during their expansive process, having that data collected in a static state of the specimen. In that paper, is described equipment designed for evaluation of pressure and temperature of expansive cements applied to ornamental rocks. Keywords: Expansive cements; Tests; Test Equipment. _____________________________________________________________________________________ 1. Introduction These manufacturers typically have different formulations for each temperature range, the A mortar is a material resulting from a mixture main variables that are modified in these of aggregates (fine), one or more binders, water formulations are takes time and evolution of and any additives in order to improve their forces in the middle. Another relevant factor is properties. The mortars are designed to meet the that the expansion should take place without most common functions such as settlement and overflow hole, ie, following an order to the coat of masonry elements (walls, columns, preferentially unilateral expansion, which is facades, etc.).. Besides these commonly used obtained by hardening of the mortar in contact mortars, we still have some special-purpose, with the expanding air in the orifice area among which stands out in this paper expansive quickly after application. mortar. Huynh & LAEFER, (2009) cite the composition The mortar is an expansive non-explosive of expansive mortar shown in Table 1.
[Show full text]
A Professional's Handbook on Grouting and Concrete Repair
A Professional’s Handbook on Grouting and Concrete Repair FIVE STAR PRODUCTS, INC. 750 Commerce Drive Fairfield, CT 06825 Support: (800) 243.2206 Fax: (203) 336.7930 FiveStarProducts.com 6x9GroutHB07.qxd:6x9_#5Handbook'05.qxd 5/3/07 2:05 PM Page 1 A Professional’s Guide to Grouting and Concrete Repair for: Architects Contractors Engineers Specifiers Owners Five Star Products Inc. 750 Commerce Drive · Fairfield CT 06825 www.FiveStarProducts.com © Copyright 2007-2012 Five Star Products Inc. 6x9GroutHB07.qxd:6x9_#5Handbook'05.qxd 5/3/07 2:05 PM Page 2 Copyright© 1981, 1983, 1985, 1988, 1989, 1991, 1995, 2005, 2007, 2012 by FIVE STAR PRODUCTS, INC. All rights reserved. No part of this book may be reproduced in any form without written permission of the publisher, FIVE STAR PRODUCTS, INC. 750 Commerce Drive Fairfield CT 06825 ® Five Star®, Five Star Structural Concrete , Five Star® Foundation System, Summerset®, and the Five Star logo are registered trademarks of FIVE STAR PRODUCTS, INC. Design-A-Spec™ is a trademark of FIVE STAR PRODUCTS, INC. Other trademarks are the property of their respective owners. NOTICE AND DISCLAIMER The tables, data, and other information in this book have been obtained from many sources, including professional architects, engineers, contractors, subcontractors, manufacturers, government organizations, trade associations, and suppliers of building materials. The publisher has made every reasonable effort to make this book accurate and authoritative, but does not warrant, and assumes no liability for, the accuracy or completeness of the text or its fitness for any particular purpose. It is the responsibility of the users to apply their professional knowledge in the use of the information contained in this book, to consult the original source, publisher, or manufacturer for additional information when appropriate, and if they themselves are not professional experts in the field, to consult with FIVE STAR PRODUCTS, INC.
[Show full text]
MATERIAL SAFETY DATA SHEET (MSDS) for PORTLAND CEMENT (Complies with OSHA and MSHA Hazard Communication Standards, 29 CFR 1910.1200And 30 CFR Part 47)
Response to USEPA Questions Commonwealth of Massachusetts October 24, 2012 New Bedford Marine Commerce Terminal (NBMCT) Introduction Thank you for this opportunity to provide USEPA additional information related to the development of the NBMCT. Development of this facility represents an important opportunity to deliver lasting environmental benefits to the New Bedford region, as well as accelerate economic development throughout the region. This document provides responses to some of the USEPA’s questions and comments submitted via e‐mail dated October 17, 2012. The format of the document will follow a comment–and‐response outline, where each of the USEPA Comments will be listed in the order in which they were presented in the USEPA’s Memoranda with the Commonwealth’s Response to each Comment presented immediately thereafter. Question 1 (Item 1 from EPA’s October 17th, 2012 e‐mail): We need final design and locations for placement of silt curtains and bubble curtains. In addition, we need to know what amendments, if any, the Commonwealth will be making to the performance standards listed in Appendix J (Attachment 5 of the TSCA Determination) and Appendix C of EPA's Draft Determination to reflect this new mitigation measure. Response: The Commonwealth previously submitted its Fish Deterrent Plan within its October 17, 2012 submission to EPA, which included the design and locations for placement of silt curtains and bubble curtains. The Commonwealth will be making no changes to the Performance Standards listed in Appendix J (Attachment 5 of the TSCA Determination) and/or Appendix C of EPA's Draft Determination in association with the silt curtains and bubble curtains associated with the Fish Deterrent Plan.
[Show full text]
Diamond Blade Overview
DIAMOND BLADE OVERVIEW Variables in Cutting The segment is the part of the blade that actually does the cutting. A measured quantity of manufactured diamonds are mixed to- gether with a specific combination of powdered metals (the matrix) and processed in graphite molds at a high temperature and high pressure to form individual segments. • Diamond blades do not really cut, instead they grind through material. • The diamond crystals remove material by scratching out particles of hard, dense materials, or by knocking out larger particles of loosely bonded abrasive material. CONTINUOUS SMOOTH RIM • Provides clean, smooth cuts on: Glazed ceramic tile, marble, granite, porcelain and quarry tile • Wet and dry specs available • Sizes: 4" – 14" diameters SERRATED / TURBO RIM • Provides fast cutting with minimal chipping on: Roof tile, unglazed tile, masonry, brick, block, paver, stone and concrete • Dry specs (can be used with water) • Sizes: 4" – 16" diameters SEGMENTED RIM • Provides maximum life and cutting strength: Concrete, reinforced concrete, asphalt, masonry, brick, block, paver and stone • Wet and dry specs available • Sizes: 4" – 60" diameters 1 www.mkdiamond.com Training Manual WET & DRY CUTTING TYPES OF CUTTING • There are two basic types of cutting – dry or wet. • The best choice of blade depends upon: - the requirements of the job - the machine/tool utilizing the diamond blade - the preference of the operator DRY CUTTING DIAMOND BLADES Because of the overwhelming popularity of handheld saws, and the flexible nature of MK diamond blades to professionally handle most ceramic, masonry, stone and concrete materials, the dry cutting blade is very attractive. Dry cutting blades are also used where water is not permitted or not convenient or where so little cutting is required that set-up of water cooled equipment would be inefficient.
[Show full text]
Project Name Cast-In-Place Bellingham, Washington Concrete Section 03300 Part 1 General
PROJECT NAME CAST-IN-PLACE BELLINGHAM, WASHINGTON CONCRETE SECTION 03300 PART 1 GENERAL 1.01 GENERAL A. All concrete shall be installed using the materials as shown on the Drawings and as called for in these Specifications. 1.02 SCOPE OF WORK A. Furnish all material, equipment, labor, and related items necessary to complete the work shown on the Drawings and/or as specified in the Specifications. The items of work to be performed shall include but are not limited to: 1. Subgrade preparation 2. Concrete anchors as shown on the Drawings 3. Concrete wall 4. Concrete bench 5. Extruded concrete curb 1.03 RELATED WORK DESCRIBED ELSEWHERE A. Related work in other sections of these Specifications includes but is not limited to: 1. Site Preparation 2. Grading, Embankment, and Backfill 3. Site Improvements 1.04 QUALITY ASSURANCE A. Standard Specifications: 1. Conform to State of Washington Standard Specifications for Road and Bridge Construction, Latest Edition 2. Standard Specifications for Municipal Public Works Construction, APWA, Latest Edition 3. Concrete Reinforcing Steel Institute, "Manual of Standard Practice" 4. Comply with building code and other local requirements, which are more stringent than the above. B. The Contractor shall establish all necessary elevations and grade stakes to provide a smooth and even surface. The Contractor shall immediately notify the Landscape Architect of any discrepancy of line and level. The Landscape Architect reserves the right to make minor changes in line or level to suit existing or developed conditions at no additional cost to the Owner. DATE: 8/21/07 03300 - 1 PROJECT NAME CAST-IN-PLACE BELLINGHAM, WASHINGTON CONCRETE SECTION 03300 1.05 SUBMITTALS A.
[Show full text]
The Impact of Grout Grout (And Sometimes the Lack of Grout) Has an Amazing Impact on the Look and Authenticity of Stonework
The Impact of Grout Grout (and sometimes the lack of grout) has an amazing impact on the look and authenticity of stonework. Selecting the desired grout technique and grout color is often as important as selecting the stone. Here we will expore expert stone grout techniques that can be used in a variety of stone projects. Wether you call it thin stone veneer, faux stone veneer or artificial stone veneer, it always benefits from grout. There are three distinct stone grout techniques: Standard Joints (Raked), Dry- Stack Joints and Overgrout Joints. General Observations Always have your mason prepare a mock-up of the grout finish you wish to use (standard, dry-stack or overgrout) prior to beginning the actual installation. Make sure you understand the intent of the finished joints, whether you are installing thin stone veneer or building an outdoor kitchen. All the stones shipped to the site should be placed face up over an area so a mental inventory of the sizes, shapes, and colors can take place. Many profiles require a rationing of certain stones throughout the entire process. Start at the corners and edges of the surfaces to be veneered and work inward. This will reduce the amount of cutting required to fit the stones. Adverse weather conditions affect manufactured stone during installation. Alternate corner colors and shapes. Avoid an "+" signs in the joints. Metal tools that strike the mortar breaks the skin which will cause moisture to rise and accelerate the drying time. It will also "polish" the grout. Grout Tips Remember that selecting and applying the grout technique is as important as laying the stone.
[Show full text]
2021QEP Catalog H0121-11688 WEB 2.Pdf
www.qep.com To assist in presenting QEP branded products in the most professional and efficient way, we have added the below icons to this catalog which indicate how each product is packaged. Please note the majority of QEP packaging is trilingual. HANG CARD COLOR CARTON Product is individually packaged on Product is individually packaged a hang card for peg hook placement. in a full color carton. Ships in Kraft shipping carton with no perforation. DISPLAY CASE SHELF CASE Packed in a white corrugated case Packed in a perforated Kraft with color display label for shelf corrugated case with color display placement. Product is individually label for shelf placement. Product is labeled and ships with a lift-off individually labeled. Kraft cover. CONTENTS TILE SAWS & CUTTERS 04 SAWS, DIAMOND BLADES, TILE CUTTERS INSTALLATION TOOLS 15 MIXERS, NIPPERS, HOLE SAWS & DRILL BITS, FILES, MALLETS, GROUT SAWS, SPONGES TILE SPACERS 30 TILE LEVELING SYSTEMS, HORSESHOE SHIMS, TRADITIONAL & LEAVE-IN SPACERS KNEEPADS 34 TROWELS & FLOATS 36 UNDERLAYMENTS & BARRIERS 41 CORK, AQUABAR BACKERBOARD & TOOLS 44 BACKERBOARD, KNIVES, CEMENT BOARD SCREWS, SEAM TAPE TEAR-OUT TOOLS 46 SCRAPERS Due to continuous improvement and product lifecycles, QEP reserves the right to discontinue products printed in this catalog. Visit qep.com for up-to-date product listings. TILE SAWS & CUTTERS 10" 900XT Pro Tile Saw SAWS & CUTTERS TOOLS SPACERS KNEEPADS TROWELS & FLOATS C US UNDERLAYMENTS ACCESSORIES INCLUDED SPECIFICATIONS • Premium porcelain rated 10" blade Item No 61900Q •
[Show full text]
Tile & Grout Cleaning Brochure
Innovating since 1974 Tile & Grout Cleaning Tile and grout cleaning is on the “Must Offer” list of services for professional cleaning contractors in both the commercial and residential markets. Not only is this service easy to learn and implement, it typically earns a higher rate per hour compared to other cleaning services you provide. This pamphlet outlines the equipment, tools and chemistry necessary to provide this valuable service SX-12 & SX-15 Truckmounts Rotary Tile Tools • A truckmount offers flexibil- • SX Rotary Tools are ity and improves efficiency fast and efficient for tile and grout cleaning • Pressure wash and • Improves performance as a recover at the same result of increased vacuum, time heat and water pressure • Increases production • Clean more sq. ft. per hour rates and reduces due to mobility fatigue #1612-7488 #1668-9782 #AW105 #1610-8235 TWBS 2 & 3 Gallon Sprayer Nautilus 1200 PSI Extractor • The TWBS sprayers come in • 1200 psi pump and dual 3-stage 2 gallon or 3 gallon sizes and vacuum motors with auto fill / auto offer the following: dump features standard • Heavy duty chemical • Truckmount power in a portable resistant hose package • 18” brass extension • Ideal for areas where a truckmount • Solid brass trigger assembly may not reach or where security • Completely rebuildable issues may be a concern (can close • Wide mouth, easy fill bottle and lock doors of facility) #1640-2911 • Viton check valve MX3-1200 #1649-2819 • Pressure gauge & relief valve HF 3 – Gallon Plastic Sprayer • All plastic sprayer that is
[Show full text]