User's Manual
Total Page:16
File Type:pdf, Size:1020Kb
User’s Manual USB2.0 OTG 2.5” hard disk enclosure CONTENTS 1. Introduction----------------------------------------------------------------------------------2 2. Package Content--------------------------------------------------------------------------2 3. Product Features--------------------------------------------------------------------------2 4. System Requirements------------------------------------------------------------------2 5. Part Number and Function------------------------------------------------------------3 6. Hard Disk Installation-------------------------------------------------------------------3 7. Replace Battery----------------------------------------------------------------------------4 8. Setting up to back up or exchanging file--------------------------5 8.1 Back up files from DSC, Pen drive, Card Reader, etc---------------------5 8.2 Exchanging files with PC or Mac------------------------------------------------6 8.2.1 Windows® 98 Driver Installation----------------------------------------6 8.2.2 Windows® 98 Un-Installation---------------------------------------------9 8.2.3 Troubleshooting------------------------------------------------------------10 8.2.4 Windows® ME Driver Installation--------------------------------------10 8.2.5 Troubleshooting------------------------------------------------------------10 8.2.6 Windows® 2000 Driver Installation-----------------------------------11 8.2.7 Troubleshooting------------------------------------------------------------11 8.2.8 Windows® XP Driver Installation--------------------------------------12 8.2.9 Troubleshooting------------------------------------------------------------12 8.2.10 MAC OS 9 Driver Installation----------------------------------------13 8.2.11 MAC OS X Driver Installation----------------------------------------14 9. Procedure of In-System-Programming (ISP) ------------------------------15 10. FAQ----------------------------------------------------------------------------------------------16 11. Disclaimer-----------------------------------------------------------------------------------17 12. FCC Statement----------------------------------------------------------------------------17 USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 1 1. Introduction This USB2.0 OTG 2.5” hard disk enclosure provides an easy way to back-up your photos of DSC, business data and MP3 music files to Hard Disk. And with its Dual Role feature, you also can download or exchange files from PC. This enclosure works with devices that support USB Mass Storage Specification. 2. Package Content Hardware: USB2.0 OTG 2.5” hard disk enclosure Power adaptor (DC-5V) USB 2.0 A/Female - Mini A/Male 15cm cable (black) USB 2.0 A/Male - Mini B/Male 1meter clear cable Screws Software: Driver software CD User’s Manual 3. Product Features 3-1 Serve as a Host (connect to DSC, Pen driver, Card Reader, etc.) USB specification revision 2.0 compliant at Full speed (12Mbps) Fully backward-compatible with USB 1.1 devices USB Mass Storage Class Bulk-Only Specification (Version 1.0) Plug and Play Hot-swapping capability 3-2 Serve as a Device (connect to PC.) USB specification revision 2.0 compliant at High speed (480Mbps) Fully backward-compatible with USB 1.1 devices USB Mass Storage Class Bulk-Only Specification (Version 1.0) Plug and Play Hot-swapping capability 4. System Requirements 4-1 Serve as a Host (connect to DSC, Pen driver, Card Reader, etc.) Support devices that with USB Mass Storage Specification 4-2 Serve as a Device (connect to PC) PC IBM PC 486DX4-100 MHz or higher or compatible system Available USB port CD-ROM drive Windows® 98SE, Windows® ME, Windows® 2000, Windows® XP MAC Power PC G3, G4, or i-Mac Available USB port CD-ROM drive Mac OS 8.6 or higher USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 2 5. Part Name and Function ⑤ ⑥ ⑦ ⑧ ④ ③ ② ① 1. Power 5. Charge 2. DC Connector 6. Battery Low 3. USB Connector 7. Error/Disk Full 4. Copy/Stop 8. Power/Access 6. Hard disk Installation Supports 40GB, 20GB or less capacity Hard Disk. 6.1 Follow the steps below to install 2.5” hard disk. 6.2 Release the screws and open the bottom cover (Figure 1 ~ 2) Screw Figure 1 Figure 2 6.3 Assemble the 2.5” hard disk to the IDE connector. (Figure 3) 6.4 Put the cover back and fasten the screws. (Figure 4) Push Screw Figure 3 Figure 4 USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 3 7 Replace battery 7.1 Follow the steps below to replace the battery. 7.2 Release the screws and open the bottom cover. (Figure 1 ~ 2) Screw Figure 1 Figure 2 7.3 Release the screws and open the up cover.(Figure 3 ~ 4) Screw Figure 3 Figure 4 7.4 Release the PCB screws. (Figure 5) 7.5 Unplug the battery connector and replace the new battery. (Figure 6) Screw Connector Figure 5 Figure 6 USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 4 8 Setting up to back up or exchanging file 8-1 Back up files from DSC, Pen drive, Card Reader, etc. 8.1.1 Install Hard Disk and Battery to Enclosure Please refer to section of “Hard disk Installation” to install Hard Disk and Battery to Enclosure. Before plug in Battery jack, please make sure the “Power” switch is at “Off” position. 8.1.2 Charge the battery Connect power adapter to this Hard Disk Enclosure and then “Charge” light will flash. After finish charging, “Charge” light will turn off. When “Battery Low” light turns on and flashing, it means this Hard Disk Enclosure has run out of battery. Please charge battery at once, unless it will do harm to your battery for over discharging. After “Battery Low” light flashing and still work on file copying, then the power will be cut off by Hard Disk. In this situation, the copying may not success and certain files will be missed. 8.1.3 Turn On Power Slide “Power” switch to “On” position, the “Power/Access” light will turn on with “Red” color. 8.1.4 Hard Disk checking If the Hard Disk is brand new and not been formatted & partition then you have to connect to PC and follow “Troubleshooting” of the following paragraph. 8.1.5 Attached Enclosure with a Mass Storage Base device The device could be DSC, Pen drive, Card Reader or others device with USB Mass Storage Specification. Connect device with USB 2.0 OTG Hard Disk Enclosure via mini A-B cable. 8.1.6 Copy files Press “Copy” button to copy files from device to Hard Disk, when coping the “Power/Access” light will flash with “Green” color. When coping, if Hard Disk is full then “Error/Disk Full“ light will turn on with “Green” color. After finish coping, “Power/Access” light will stay with “Red” color and all files that have been copied to Hard Disk will be named from “DSK00000” sequentially. Before copying, if “Error/Disk Full” light is flashing with “Red” color, then it means that the device is not Mass Storage device. When copying, if “Error/Disk Full” light is flashing with “Red” color and “Battery low” light is flashing then it means you are running out of battery. USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 5 8.2 Exchanging files with PC or Mac Connect the “D” connector of the Enclosure with PC, then “Busy/Ready Write” light will turn on with “Orange” color. 8.2.1 Windows® 98 Installation 8.2.1.1 Connect the USB port of USB2.0 OTG 2.5” hard disk enclosure to PC with USB cable. 8.2.1.2 The “Add New Hardware Wizard” dialog box will appears as below, click “Next” to continue. 8.2.1.3 Choose “Search for the best driver for your device (Recommended)” then click “Next”. 8.2.1.4 Select “Specify a location” and type “D:\DRIVER\USB2.0 OTG 2.5 INCH HARD DISK ENCLOSURE” (D: represents CD-ROM) in the dialog box, then click “Next” USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 6 8.2.1.5 Choose “The updated driver (Recommended) M5637, USB (OTG) Storage Device” then click “Next”. 8.2.1.6 Windows® will search the driver for this device. Make sure the driver that Windows® found is “D:\DRIVER\USB2.0 OTG 2.5 INCH HARD DISK ENCLOSURE\UMSTOR.INF” then click “Next”. 8.2.1.7 Click “Finish” to complete the installation procedure of “M5637, USB (OTG) Storage Device” USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 7 8.2.1.8 If the driver has been successfully installed then double click on “My Computer”, there will have a new device and name of “(E:)” at desktop as shown below. 8.2.1.9 After Windows® installed all the driver, you have to check “My Computer”-“Control Panel”-“System”-”Device Manager” to make sure the driver has already installed. Then, in the “Disk Drives” it will show a “USB 2.0 Storage Device”, in the “Hard disk controllers” it will show a new item of “USB Mass Storage Device” USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 8 8.2.2 Windows® 98 un-installation 8.2.2.1 Click on “Add/Remove Programs” of “Control Panel” to un-install it. The “Add/Remove Program Properties” dialog show as below. Select “USB Storage Toolbox” and click on “Add/Remove” then click “OK” to continue. 8.2.2.2 Click “OK” to confirm un-installation. 8.2.2.3 Click on “Yes , I want to restart my computer now” to restart computer and complete uninstall procedure. USB2.0 OTG 2.5” hard disk Enclosure User’s Manual 9 8.2.3 Troubleshooting If the Hard Disk (brand new HD) didn't show in “My Computer” after the driver is being successfully installed, please go to “MS-DOS Prompt”, FDISK and FORMAT the new hard disk. (Please refer to MS-DOS instruction.) 8.2.4 Windows® ME installation It doesn’t need to install any extra driver at Windows® ME Connect the USB port of USB2.0 OTG 2.5” hard disk enclosure to PC with USB cable. System will auto detect the device and load the driver then create a new device at desktop. 8.2.5 Troubleshooting After the driver be successfully installed, but the hard disk does not shown at “My Computer”. If it is a brand new hard disk, please go to “MS-DOS Prompt” and FDISK, FORMAT new hard disk.