TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/1

Annexure – II

ERO/MMD/585/0824 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/1

(EOT Crane Cap. 25/7.5T x 2)

Leading Parameters :

No Item Details 1 Location (Sub-shop Name) Carriage Repair shop Harnaut 2 Capacity, span and type Double crab each crab 251 capacity 2.1 Type Conventional Double Girder 2.2 Main hoist 25 Tonnes 2.3 Auxiliary hoist 7.5 Tonnes 3 Class of duty III IS : 3177 4 Crane controls from Cabin & Remote controls 5 Speeds (meter/min.) 5.1 Main hoist 5 5.2 Auxiliary hoist 10 5.3 Long Travel 31.5 5.4 Cross Traverse 20 6 Structural details 6.1 Span (center to center of gantry rails) 30000 mm 6.2 Top of gantry rail (or bottom flange of I-beam) 3500 mm To lowest overhead obstruction 6.3 Top of gantry rail (or bottom flange of I-beam) 12500 mm To floor level 6.4 Lift of hook above floor level (MH) 11750 mm 6.5 Lift of hook above floor level (AH) 11500 mm 6.6 Drop of hook below floor level (MH) -- 6.7 Drop of hook below floor level (AH) -- 6.8 Hook approach to centre line of gantry Rail (cabin end) (MH) 1600 mm (AH) 2600 mm

6.9 Hook approach to centre line of gantry Rail (other end) (MH) 1900 mm (AH) 2900 mm 6.10 Distance between centre of hook of MH & AH 1000 mm (Max.) 6.11 Side clearance from centre line of gantry rail/I- 500 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 500 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest To suit to the design of crane

tech specification for eot crane cap 1 Structural member of the crane 6.14 Vertical clearance from floor level to lowest structural member bottom cabin 6.15 Size and weight unit length of gantry rail CR 80 Rail & 64.2 kg/m 6.16 Rail head width 87 mm 7 Bay length & (DSL) 7.1 Length of gantry on which crane is to operate 220 M. (approx.) 7.2 Type & Length of Down shop lead Shrouded type DSL 220 mts) 220 mts in 2 bays 8 Type of operator’s cabin Open 9 Crane has to work in (indoors/outdoors/both) Indoor 10 Any abnormal working conditions -- 11 Minimum distance between Hook to Hook To suit to the design of crane centers (MH) (main hooks of the crabs should be closer to the gantry rail) 12 Other Requirement Two sets of Lifting tackles. Slings, Four legged chain with C-type hooks, Two legged chain with C-type hooks

Necessary maintenance spares and concomitant accessories have to be supplied with crane. Details including drawings of Lifting tackles, Slings, Four legged chain with C-type hooks. Two legged chain with C-type hooks have to be submitted before supply for approval. Necessary tooling and gauges shall have also to be supplied with he machine. Supplier shall have to arrange free training for user staff in operation and maintenance of the crane. The supplier shall have to provide related drawings/diagrams (Civil, mechanical & electrical etc) electrical load & electrical circuitry.

tech specification for eot crane cap 2 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/2

(EOT Crane Cap. 10/1 T )

No Item Details 1 Location (Sub-shop name) Sheet Metal Shop/Harnaut 2 Capacity, span and type 10T capacity 2.1 Type Conventional Double-Girder 2.2 Main hoist 10 Tonnes 2.3 Auxiliary Hoist 1.0 Tonnes 3 Class of duty 111 IS : 3177 4 Crane controls from Cabin & Pendent 5 Speeds (meter/min.) 5.1 Main hoist 4 5.2 Auxiliary hoist 8.0 5.3 Long Travel 63.0 5.4 Cross Traverse 31.5 6 Structural details 6.1 Span (centre to centre of gantry rails) 23800 mm 6.2 Top of gantry rail (or bottom flange of I- beam) 2500 mm To lowest overhead obstruction 6.3 Top of gantry rail (for bottom flange of I-beam) 6500 mm To floor level 6.4 Lift of hook above level (MH) 6200 mm 6.5 Lift of hook above floor level (AH) 6300 mm 6.6 Drop of hook below floor level (MH) 500 mm 6.7 Drop of hook below floor level (AH) 500 mm 6.8 Hook approach to centre line of gantry

Rail (cabin end) (MH) (AH) 6.9 Hook approach to centre line of gantry

Rail (other end) (MH) (AH) 6.10 Distance between centre of hook of MH & AH 800 mm (Max) 6.11 Side clearance from centre line of gantry rail I- 350 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 350 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest To suit the design of the crane Structural member of the crane 6.14 Vertical clearance from floor level to lowest To suit the design of the crane Structural member bottom cabin 6.15 Size and weight/unit length of gantry rail CR 60 Rail & 40 kg/mtr 6.16 Rail head width 66 mm

tech specification for eot crane cap 3 7 Bay length 7.1 Length of gantry on which crane is to operate 75 M (approx) 7.2 Type & Length of Down shop lead MS Angle type 75 M to be supplied & erected by supplier 8 Type of operator’s cabin Fixed & Closed 9 Crane has to work in (indoors/outdoors/both) Both 10 Any abnormal working conditions -- 11 Width of the crane (LT buffer to buffer) Max 12 Minimum distance between Hook to Hook To suit the design of the crane centres (MH) (main hooks of the crabs should be closer to the gantry rail) 13 Other Requirement Two sets of Lifting tackles. Slings, Four legged chain with C-type hooks, two legged chain with C- type hooks

Necessary maintenance spares and concomitant accessories have to be supplied with crane. Details including drawings of Lifting tackles, Slings, Four legged chain with C-type hooks, two legged chain with C-type hooks have to be submitted before supply for approval Necessary tooling and gauges shall have also to be supplied with the machine. Supplier shall have to arrange free training for user staff in operation and maintenance of the crane. The supplier shall have to provide related drawings/diagrams (Civil, mechanical & electrical etc) electrical load & electrical circuitry.

tech specification for eot crane cap 4 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/3

(EOT Crane Cap. 10/1 T )

No Item Details 1 Location (Sub-shop name) Sheet Metal Shop/Harnaut 2 Capacity, span and type 10T capacity 2.1 Type Conventional Double-Girder 2.2 Main hoist 10 Tonnes 2.3 Auxiliary Hoist 1.0 Tonnes 3 Class of duty IV IS : 3177 4 Crane controls from Cabin & Pendent 5 Speeds (meter/min.) 5.1 Main hoist 4 5.2 Auxiliary hoist 8.0 5.3 Long Travel 63.0 5.4 Cross Traverse 31.5 6 Structural details 6.1 Span (centre to centre of gantry rails) 13800 mm 6.2 Top of gantry rail (or bottom flange of I- beam) 2500 mm To lowest overhead obstruction 6.3 Top of gantry rail (for bottom flange of I-beam) 6500 mm To floor level 6.4 Lift of hook above level (MH) 6200 mm 6.5 Lift of hook above floor level (AH) 6300 mm 6.6 Drop of hook below floor level (MH) 500 mm 6.7 Drop of hook below floor level (AH) 500 mm 6.8 Hook approach to centre line of gantry

Rail (other end) (MH) (AH) 6.10 Distance between centre of hook of MH & AH 800 mm (Max) 6.11 Side clearance from centre line of gantry rail I- 350 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 350 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest To suit the design of the crane Structural member of the crane 6.14 Vertical clearance from floor level to lowest To suit the design of the crame Structural member bottom cabin 6.15 Size and weight/unit length of gantry rail CR 60 Rail & 40 kg/mtr 6.16 Rail head width 66 mm 7 Bay length 7.1 Length of gantry on which crane is to operate 100 M (approx)

tech specification for eot crane cap 5 7.2 Type & Length of Down shop lead MS Angle type 100 M to be supplied & erected by supplier 8 Type of operator’s cabin Fixed & Opened 9 Crane has to work in (indoors/outdoors/both) Indoor and outdoor 10 Any abnormal working conditions -- 11 Width of the crane (LT buffer to buffer) Max 12 Minimum distance between Hook to Hook To suit the design of the crane centres (MH) (main hooks of the crabs should be closer to the gantry rail) 13 Other Requirement Two sets of Lifting tackles. Slings, Four legged chain with C-type hooks, two legged chain with C- type hooks and two lifting magnets of size 1.0 meter diameter (approx) & of capacity 31 with 30 minutes break up for lifting steel sheets of size length. 3 m width 1.5 m & thickness 2 mm to 10 mm.

tech specification for eot crane cap 6 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/4 (EOT Crane Cap. 3/0.5 T )

No Item Details 1 Location (Sub-shop name) HRS Shop Harnaut 2 Capacity, span and type 3T capacity 2.1 Type Single Girder 2.2 Main hoist 3 Tonnes 2.3 Auxiliary Hoist 0.5 Tonnes 3 Class of duty III IS : 3177 4 Crane controls from Pendent & Remote control 5 Speeds (meter/min.) 5.1 Main hoist 4 5.2 Auxiliary hoist 8.0 5.3 Long Travel 63.0 5.4 Cross Traverse 31.5 6 Structural details 6.1 Span (centre to centre of gantry rails) 13800 mm 6.2 Top of gantry rail (or bottom flange of 1- beam) 2500 mm To lowest overhead obstruction 6.3 Top of gantry rail (for bottom flange of 1-beam) 6500 mm To floor level 6.4 Lift of hook above level (MH) 6200 mm 6.5 Lift of hook above floor level (AH) 6300 mm 6.6 Drop of hook below floor level (MH) 500 mm 6.7 Drop of hook below floor level (AH) 500 mm 6.8 Hook approach to centre line of gantry

Rail (other end) (MH) (AH) 6.10 Distance between cente of hook of MH & AH 800 mm (Max) 6.11 Side clearance from centre line of gantry rail I- 350 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 350 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest To suit the design of the crane Structural member of the crane 6.14 Vertical clearance from floor level to lowest To suit the design of the crame Structural member bottom cabin 6.15 Size and weight/unit length of gantry rail CR 60 Rail & 40 kg/mtr 6.16 Rail head width 66 mm 7 Bay length 7.1 Length of gantry on which crane is to operate 80 M (approx) 7.2 Length of Down shop lead reqd. 80 M to be supplied & erected by supplier tech specification for eot crane cap 7 8 Type of operator’s cabin Pendent & Remote control 9 Crane has to work in (indoors/outdoors/both) Indoor 10 Any abnormal working conditions -- 11 Width of the crane (LT buffer to buffer) Max 12 Minimum distance between Hook to Hook To suit the design of the crane centres (MH) (main hooks of the crabs should be closer to the gantry rail) 13 Other Requirement Two sets Lifting tackles. Slings, Four legged chain with C-type hooks, two legged chain with C- type hooks

tech specification for eot crane cap 8 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/5 (EOT Crane Cap. - 2T )

No Item Details 1 Location (Sub-shop name) WAS Shop/ Harnaut 2 Capacity, span and type 2T capacity 2.1 Type Single Girder 2.2 Main hoist 2 Tonnes 2.3 Auxiliary Hoist N A 3 Class of duty III IS : 3177 4 Crane controls from Pendent & Remote 5 Speeds (meter/min.) 5.1 Main hoist 4 5.2 Auxiliary hoist 8.0 5.3 Long Travel 63.0 5.4 Cross Traverse 31.5 6 Structural details 6.1 Span (centre to centre of gantry rails) 18,800 mm 6.2 Top of gantry rail (or bottom flange of I- beam) 2500 mm To lowest overhead obstruction 6.3 Top of gantry rail (for bottom flange of I-beam) 6500 mm To floor level 6.4 Lift of hook above level (MH) 6200 mm 6.5 Lift of hook above floor level (AH) NA 6.6 Drop of hook below floor level (MH) 500 mm 6.7 Drop of hook below floor level (AH) NA 6.8 Hook approach to centre line of gantry

Rail (other end) (MH) (AH) 6.10 Distance between cente of hook of MH & AH N A (Max) 6.11 Side clearance from centre line of gantry rail I- 350 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 350 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest To suit the design of the crane Structural member of the crane 6.14 Vertical clearance from floor level to lowest To suit the design of the crane Structural member bottom cabin 6.15 Size and weight/unit length of gantry rail CR 60 Rail & 40 kg/mtr 6.16 Rail head width 66 mm 7 Bay length 7.1 Length of gantry on which crane is to operate 60 M (approx)

tech specification for eot crane cap 9 7.2 Type & Length of Down shop lead MS Angle & 60 M to be supplied & erected by supplier 8 Type of operator’s cabin NA 9 Crane has to work in (indoors/outdoors/both) Indoor 10 Any abnormal working conditions -- 11 Width of the crane (LT buffer to buffer) Max 12 Minimum distance between Hook to Hook To suit the design of the crane centres (MH) (main hooks of the crabs should be closer to the gantry rail) 13 Other Requirement Two sets of Lifting tackles. Slings, Four legged chain with C-type hooks, two legged chain with C- type hooks

Necessary maintenance spares and concomitant accessories have to be supplied with crane. Details including drawings of Lifting tackles, Slings, Four legged chain with C-type hooks, two legged chain with C-type hooks have to be submitted before supply for approval Necessary tooling and gauges shall have also to be supplied with the machine. Supplier shall have to arrange free training for user staff in operation and maintenance of the crane. The supplier shall have to provide related drawings/diagrams (Civil, mechanical & electrical etc) electrical load & electrical circuitry

tech specification for eot crane cap 10 TECHNICAL SPECIFICATION NO. HRK/Mech/M&P/EOT/6 (EOT Crane Cap. 2T )

No Item Details 1 Location (Sub-shop name) WBP Shop/Harnaut 2 Capacity, span and type 2T capacity 2.1 Type Single Girder 2.2 Main hoist 2 Tonnes 2.3 Auxiliary Hoist N A 3 Class of duty III IS : 3177 4 Crane controls from Pendent & Remote 5 Speeds (meter/min.) 5.1 Main hoist 4 5.2 Auxiliary hoist 8.0 5.3 Long Travel 63. 5.4 Cross Traverse 31.5 6 Structural details 6.1 Span (centre to centre of gantry rails) 14000 mm 6.2 Top of gantry rail (or bottom flange of I- beam) NA to lowest overhead obstruction 6.3 Top of gantry rail (for bottom flange of I-beam) 6500 mm to floor level 6.4 Lift of hook above level (MH) 6200 mm 6.5 Lift of hook above floor level (AH) NA 6.6 Drop of hook below floor level (MH) 500 mm 6.7 Drop of hook below floor level (AH) NA 6.8 Hook approach to centre line of gantry

Rail (other end) (MH) (AH) 6.10 Distance between centre of hook of MH & AH N A (Max) 6.11 Side clearance from centre line of gantry rail I- 350 mm beam to nearest side obstruction 6.12 Side clearance from centre line of gantry rail/I- 350 mm beam to nearest side obstruction 6.13 Vertical clearance from floor level to lowest to suit the design of the crane Structural member of the crane 6.14 Vertical clearance from floor level to lowest to suit the design of the crame Structural member bottom cabin 6.15 Size and weight/unit length of gantry rail CR 60 Rail & 40 kg/mtr 6.16 Rail head width 66 mm 7 Bay length 7.1 Length of gantry on which crane is to operate 60 M (approx)

tech specification for eot crane cap 11 7.2 Type & Length of Down shop lead MS Angle & 60 M to be supplied & erected by supplier 8 Type of operator’s cabin NA 9 Crane has to work in (indoors/outdoors/both) Outdoor 10 Any abnormal working conditions -- 11 Width of the crane (LT buffer to buffer) Max 12 Minimum distance between Hook to Hook to suit the design of the crane centres (MH) (main hooks of the crabs should be closer to the gantry rail) 13 Other Requirement Two sets of Lifting tackles. Slings, Four legged chain with C-type hooks, two legged chain with C- type hooks.

Necessary maintenance spares and concomitant accessories have to be supplied with crane. Details including drawings of Lifting tackles, Slings, Four legged chain with C-type hooks, two legged chain with C-type hooks have to be submitted before supply for approval. Necessary tooling and gauges shall have also to be supplied with the machine.

Supplier shall have to arrange free training for user staff in operation and maintenance of the crane. The supplier shall have to provide related drawings/diagrams (Civil. Mechanical & electrical etc.) (electrical load & electrical circuitry).

tech specification for eot crane cap 12