3896 Select, Use, and Maintain Aeronautical Engineering Tools and Equipment

NZQA registered unit standard 3896 version 5 Page 1 of 3

Title Select, use, and maintain aeronautical engineering tools and equipment

Level 3 Credits 12

Purpose People credited with this unit standard are able to: select aeronautical engineering tools and equipment; and use and maintain aeronautical engineering tools and equipment.

Classification Aeronautical Engineering > Aeronautical Engineering - Core

Available grade Achieved

Explanatory notes

1 All tasks are to be carried out in accordance with enterprise procedures, the enterprise being the organisation carrying out the work. Enterprise procedures referred to in this unit standard are the applicable procedures found in the following: enterprise exposition; manufacturer publications; Government and local body legislation; airworthiness authority requirements.

2 Tools and equipment may include but are not limited to: hand tools – spanners, screw drivers, pliers, hammers, files, socket sets, torque wrenches, drills, saws, clamps, chisels, drifts, reamers, taps and dies, snips and shears, wire strippers, hole punches, vices, crimping tools; powered tools and equipment – isolating transformers, extension power leads, portable drills, portable grinders, drill presses, bench grinders, air driven tools, dimplers; support equipment – lifting tackle, jacks, benders and folders, guillotines, grease guns, ladders, stands; measuring and marking out equipment – micrometers, callipers, vernier gauges, dial test indicators, bore gauges, rulers, straight edges, combination set squares and protractors, clinometers, hole and telescopic gauges, limit and comparator gauges and mandrels, surface tables and plates, vee and scribing blocks, squares, level gauges, marking out compounds, scribers, steel tapes, inclinometer’s, mass balances, spring balances, stop watches, fixed gauges.

3 All calibrated tooling and electrical tooling must be within current compliance in accordance with enterprise procedures.

ServiceIQ Ó New Zealand Qualifications Authority 2018 SSB Code 9068 NZQA registered unit standard 3896 version 5 Page 2 of 3

Outcomes and evidence requirements

Outcome 1

Select aeronautical engineering tools and equipment.

Range may include but is not limited to – pre-use inspection.

Evidence requirements

1.1 Hand tools are selected for the task in accordance with enterprise procedures.

1.2 Powered tools and equipment are selected for the task in accordance with enterprise procedures.

1.3 Support equipment is selected and set up for the task in accordance with enterprise procedures.

1.4 Measuring and marking-out equipment is selected for the task in accordance with enterprise procedures.

Outcome 2

Use and maintain aeronautical engineering tools and equipment.

Evidence requirements

2.1 Tools and equipment are used in a safe and efficient manner, to produce the required outcome without damaging components or tooling, in accordance with enterprise procedures.

2.2 Tools and equipment are maintained in accordance with enterprise procedures.

Range clean, repair, replace, report defects.

2.3 Tools and equipment are stored safely and securely after use in accordance with enterprise procedures.

ServiceIQ Ó New Zealand Qualifications Authority 2018 SSB Code 9068 NZQA registered unit standard 3896 version 5 Page 3 of 3

Planned review date 31 December 2018

Status information and last date for assessment for superseded versions Process Version Date Last Date for Assessment Registration 1 19 June 1995 31 December 2016 Revision 2 7 August 1997 31 December 2016 Revision 3 8 May 2001 31 December 2016 Review 4 20 April 2006 31 December 2016 Review 5 19 September 2013 N/A

Consent and Moderation Requirements (CMR) reference 0028 This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.

Please note Providers must be granted consent to assess against standards (accredited) by NZQA, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment.

Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards.

Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards.

Requirements for consent to assess and an outline of the moderation system that applies to this standard are outlined in the Consent and Moderation Requirements (CMR). The CMR also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.

Comments on this unit standard

Please contact the ServiceIQ [email protected] if you wish to suggest changes to the content of this unit standard.

ServiceIQ Ó New Zealand Qualifications Authority 2018 SSB Code 9068