DEP Dicision of Recreation and Parks Uniforms Specificaitons s1

DEP Division of Recreation and Parks Uniform Specifications

5.1.1: SKIRT, WOMEN

FABRIC: 100% POLYESTER Comfort-Fiber

COLOR: Spruce Green, Shade #8772

STYLE: “A” line, or Department approved equivalent. Adjustable waistband with button closure, Two inset pockets.

WAISTBAND: Double self goods, one pierce approximately 1” wide with a stretch Ban-rol, or equivalent, interlining. Front end to be finished with an approximate 2” extension with pointed edge, and with an approximate ¾” horizontal buttonhole center on end of extension. Two (2) 22 Ligne Polymer, or equivalent, matching buttons sewn on inside of front of waistband approximately 2 ½” from edge of waistband.

POCKETS: One Pocket on each side of skirt with and opening off each side seam approximately 7” long. Pockets to be approximately 12” long and 6 ½” wide and set into the waistband seam at top. Pocket to be made of self fabric and stitched to side seam approximately 2” down to side seam approximately 2” below pocket opening.

SEWING: Side seams and pocket to be SSA-1 stitch type, 301 standard, 8-10 stitches per inch. Edges and seams serged. Hem blind stitched.

5.1.2: TROUSERS, DRESS STYLE FOR MEN

COLOR: SPRUCE

FABRIC: 75% Dacron Polyester, 25% Wool , Gabardine weave-Mechanical stretch 10% Breaking Strength: 125 Lbs. In the Warp, 80 Lbs. In the Filling. Weight 11.00- 11.50 Oz. per linear yard. Construction: 77 ends per inch, 56 picks per inch. Fiber Length: Wool equals 3-3.5 inches average minimum, Polyester equals 3 inches minimum Dye Procedure: Piece Dyed.

STYLE: The style shall conform to modern updated contour cut men’s uniform trousers. Plain front, 2 front and 2 back pockets. Front pockets are quarter top style with a minimum of 5" opening. The front pockets will have separate handset inside facing to give four-ply strength at the entry of the pockets. The front pockets will be hung to the side seam of the trousers and locked with a bar-tack at the top and bottom of the pocket opening. The two back pockets will have a Reece piped entry. They will have a minimum opening of 5". The left back pocket will have a tab to button closure. They will be bartacked on right and left side for extra strength. Front and back pockets are to be stitched, turned and topstitched.

01a4ac6e7f1eb832df7b4553d7eba722.doc Page 1 of 36 DEP Division of Recreation and Parks Uniform Specifications

BELT LOOPS: All belt loops are to be lined and of double thickness butted on reverse side and blind stitched. They shall be a minimum of 5/8" wide by 2" long and are to be sewn into the waistband seam at top and bottom.

WAISTBAND: Outside waistband is to be a minimum of 2” wide (self-material). It will be sewn to the waistband lining at top and waistband curtain is then blind stitched at the bottom.

WAISTBAND CONSTRUCTION: Right fly lining and crotch piece extension lined with same material as pocketing. (To be one piece and sewn down flat). There is to be continuous French fly extension at the end of the French fly that will attach to button that is sewn on left side of waistband lining. Left fly is to be lined and corded.

INNER WAISTBAND: Inner waistband to be Comfort in Action IV with XI.91 interlining. Inner waistband to be composed in two parts, a 2-1/2” wide two-zone inner waistband and a 1” wide interlining of elastic. The 2-1/2” wide inner waistband shall be composed of a 4% nylon/ 86% Polyester/ 10% Spandex. It will have 45% manual elongation and a two-zone construction. The upper zone is stiff to give body to upper waistband portion and help prevent waistband rollover and ribbed to help hold shirttail in. The lower part is soft to stretch around the hips, supporting the slack. The 1” wide stiff elastic will be an interlining to form the cap of the trousers and help prevent waistband rollover. This elastic shall be composed of 5% Nylon Monofilament / 84% Polyester / 11% Spandex with a manual elongation of 35% (+ or – 10%). Waistband is blindstitched, not topstitched to assure banding stretch. Bottom portion is specially beamed and warped in a diagonal twill portion of band, approximately ¼” high letters (CIA III or IV), with a 4.75” separation between each identification repeat.

ZIPPER & CLOSURE: Talon (Gripper-Zipper) #42 Brass or equivalent will also have metal bottom stop, permanent press treated tape, hook-flex steel waistband closure.

STITCHING, PRESSING AND FINISHING: The trousers must be stitched with matching thread and all stitching must be 10-11 stitches per inch. The trousers must be neatly pressed on hot head presses and properly shaped. Outseams and inseams must be pressed open to maintain a neat and professional appearance. The trousers must be cleaned and finished to eliminate loose threads. There must be a Texpak clip attached to the top fly of the finished trousers to insure shape retention during shipping.

POCKETING: All pocketing will be made of a polyester/cotton blend permanent dress drill with an approximate content of 50% polyester / 50% cotton in the spun warp- 100% texturized polyester in the filling; for a total content of 70% polyester / 30% cotton. Pocketing will harmonize with color of trousers and waistband. Pocketing shall test to a minimum abrasion of 225 cycles per ASTM D3886. (Inflated Diaphragm) for

the uncoated area; Bottom of front pockets, (aprox. 2-1/2"), shall be Dura Ruff coated. Area shall test to a minimum abrasion of 1100 cycles before initial rupture. This shall substantially increase pocket strength over reinforced pockets without the unsightly ridges of double pockets.

LABELING: All trousers will be finished with a woven (not printed) label, permanently affixed. It will include the correct fiber content of the fabric and identification of brand as well as garment care instructions.

CREASING: Front & Back Fashion Set permanent creases. Fashion Set is a special process for permanent front and back creases, formed by an invisible resin treatment. It is bonded to the inside of the trousers, insuring clean, sharp, straight creases. Fashion Set is not a baked-in process that can burn or damage cloth fibers.

CROTCH LINING: Back panels to have crotch liners. Triangular dimensions of crotch liners are to be approximately 3-1/2” x 9”. Crotch lining to be made of black satin 100% Polyester fabric

CARE INSTRUCTIONS: Dry-clean or machine-wash warm with like colors. (90 to 100 degrees F.) (32 to 43 degrees C.) Tumble-dry (120 degrees F.) (49 degrees C.) Warm iron if needed.

SIZES: To be sizes 28,29,30,31,32,33,34,35,36,37,38,40 to 50 (even sizes only) in open unfinished lengths to be hemmed to individual request.

All measurements are approximate and "based" on size 34. All other sizes are graded from these measurements according to size.

5.1.3: TROUSERS, DRESS STYLE FOR WOMEN

COLOR: SPRUCE

FABRIC: 75% Dacron Polyester, 25% Wool , Gabardine weave-Mechanical stretch 10% Breaking Strength: 125 Lbs. In the Warp, 80 Lbs. In the Filling. Weight 11.00- 11.50 Oz. per linear yard. Construction: 77 ends per inch, 56 picks per inch. Fiber length: Wool equals 3-3.5 inches average minimum, Polyester equals 3 inches minimum Dye Procedure: Piece Dyed.

STYLE: The style shall conform to modern updated contour cut ladies uniform trousers. Plain front, 2 front and 2 back pockets. Front pockets are quarter top style with a minimum of 5" opening. The front pockets will have separate handset inside facing to give four-ply strength at the entry of the pockets. The front pockets will be hung to the side seam of the trousers and locked with a bar-tack at the top and bottom of the pocket opening.

The two back pockets will have a Reece piped entry. They will have a minimum opening of 5". Front and back pockets are to be stitched, turned and topstitched.

BELT LOOPS: All belt loops are to be lined and of double thickness butted on reverse side and blind stitched. They shall be a minimum of 5/8" wide by 2" long and are to be sewn into the waistband seam at top and bottom.

WAISTBAND: Outside waistband is to be a minimum of 1 3/4" wide, (self-material). It will be sewn to the waistband lining at top and waistband curtain is then blind stitched at bottom.

WAISTBAND CONSTRUCTION: Right fly lining and crotch piece extension are lined with same material as pocketing. (To be one piece and sewn down flat). Left fly is to be lined and corded.

INNER WAISTBAND: Inner waistband to be Comfort in Action IV with XI.91 interlining. Inner waistband to be composed in two parts, a 2-1/2” wide two-zone inner waistband and a 1” wide interlining of elastic. The 2-1/2” inner waistband shall be composed of a 4% nylon/ 86% Polyester/ 10% Spandex. It will have 45% manual elongation and a two-zone construction. The upper zone is stiff to give body to upper waistband portion and help prevent waistband rollover and ribbed to help hold shirttail in. The lower part is soft to stretch around the hips, supporting the slack. The 1” wide stiff elastic will be an interlining to form the cap of the trousers and help prevent waistband rollover. This elastic shall be composed of 5% Nylon Monofilament / 84% Polyester / 11% Spandex with a manual elongation of 35% (+ or – 10%). Waistband is blindstitched, not topstitched to assure banding stretch. Bottom portion is specially beamed and warped in a diagonal twill portion of band, approximately ¼” high letters (CIA III or IV), with a 4.75” separation between each identification repeat.

ZIPPER & CLOSURE: Talon (Gripper-Zipper) #42 Brass or equivalent will also have metal bottom stop, permanent press treated tape, hook-flex steel waistband closure.

STITCHING, PRESSING AND FINISHING: The trousers must be stitched with matching thread and all stitching must be 10-11 stitches per inch. The trousers must be neatly pressed on hot head presses and properly shaped. Outseams and inseams must be pressed open to maintain a neat and professional appearance. The trousers must be cleaned and finished to eliminate loose threads. There must be a Texpak clip attached to the top fly of the finished trousers to insure shape retention during shipping.

POCKETING: All pocketing will be made of a polyester/cotton blend permanent dress drill with an approximate content of 50% polyester / 50% cotton in the spun warp- 100% texturized polyester in the filling; for a total content of 70% polyester / 30% cotton. Pocketing will harmonize with color of trousers and waistband. Pocketing shall test to a minimum abrasion of 225 cycles per ASTM D3886. (Inflated Diaphragm) for

the uncoated area; Bottom of front pockets, (approx. 2-1/2"), shall be Dura Ruff coated. Area shall test to a minimum abrasion of 1100 cycles before initial rupture. This shall substantially increase pocket strength over reinforced pockets without the unsightly ridges of double pockets.

LABELING: All trousers will be finished with a woven (not printed) label, permanently affixed. It will include the correct fiber content of the fabric and identification of brand as well as garment care instructions.

CREASING: Front & back Fashion Set permanent creases. Fashion Set is a special process for permanent front and back creases, formed by an invisible resin treatment. It is bonded to the inside of the trousers, insuring clean, sharp, straight creases. Fashion Set is not a baked-in process that can burn or damage cloth fibers.

CARE INSTRUCTIONS: Dry-clean or machine-wash warm with like colors. (90 to 100 degrees F.) (32 to 43 degrees C.) Tumble-dry (120 degrees F.) (49 degrees C.) Warm iron if needed.

SIZES: To be sizes 4 to 24 in open unfinished lengths to be hemmed to individual request.

All measurements are approximate and "based" on size 12. All other sizes are graded from these measurements according to size.

5.1.4: TROUSERS, WORK STYLE FOR MEN/WOMEN

FABRIC: 65% polyester, 35% combed cotton, 8 oz. per square yard, 3 x 1 right hand twill with a post-cured finish. Fabric must be treated with “Soil-bar” soil release and wicking finish, or equivalent process, and have a post-cured finish. All colors must be vat dyed.

COLOR: Spruce Green

STYLE: Shall be made on a uniform pattern with a plain front with 2 quarter top pockets and 2 back pockets.

POCKETS: The front pockets shall have a minimum opening of 6” and be a minimum 6” deep from the bottom of the opening. They are to be stitched, turned and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1¼” wide. The back pockets will have a minimum opening of 5” and be a minimum 5¾” deep. The pocket closure over the left pocket shall be ¾” wide and blind stitched so that no stitching shall be seen on the outside of the loop. The front and back pockets shall have two straight bar tacks, one on each side.

POCKETING: All pocketing shall be made of a polyester/polyester-cotton fabric and the color shall harmonize with the outer fabric color. All front pocketing shall have a 2½” Dura Ruff coating. (See above).

WAISTBAND: The waistband shall be a minimum of 1½” wide and shall be closed with a crushproof hook and eye, the eye being bar tacked, or other reinforced stitching, for stability. The waistband curtain a polyester/polyester-cotton fabric with the color of the fabric to harmonize with the outer fabric. No roll waistband stiffener, minimum 5/8” in width, shall be sewn into the waistband on the front of the trouser from side seam to side seam. The trousers are to be made with a continuous close waistband.

FLY: The right fly lining will be the same fabric and color as the waistband curtain. The right fly lining shall be sewn to the left fly below the zipper. A separate French fly made of the outer fabric shall be sewn to the inside right fly.

BELT LOOPS: There shall be a minimum of 5 drop belt loops on waist sizes 28,29,30 a minimum of 7 on all sizes over 30. Each loop is to be a minimum of 5/8” wide and blind stitched so no stitching shall be seen on the outside of the loop. Except for the center back loop which shall be tacked on, all loops will be sewn into the rocap and bar tacked ¼” below the waistband so as to accommodate a 1¾” belt.

ZIPPER: The trousers shall be closed with a Scovil Guardloc or equivalent brass zipper and have a brass bottom stop at the base of the zipper chain. A straight bar tack, or other reinforced stitching, will be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack, or other reinforced stitching, located below the bottom zipper stop on the inside of the trouser.

SEAMING: The entire trouser is to be seamed with polyester core or 100% polyester spun thread. The seat seams shall be stitched with a tandem needle seat seaming machine. All exposed inside seams of the trousers are to be serged.

FINISHING AND PRESSING: All loose threads shall be removed. Trousers must have Lintrak seam retention, or equivalent process, applied as part of the manufacturing process. No post- production will be accepted. Trousers must be pressed completely and properly with the side seam, inseam, and seat seam pressed open.

5.1.5: SHORTS, MEN/WOMEN

SIZE: 28 – 46

COLOR: Spruce 31163 (mal) & 30133 (female)

FABRIC: 65% Polyester/35% Cotton Twill Weight 8 oz/yd²

CONSTRUCTION/DETAILS:

WAISTBAND: Waistband will be constructed of 1-ply self-fabric, folded and finished 1½” wide. Ends are single needle closed to yield a clean finish. The zipper is double needle stitch.

BAND CLOSURE: Band closure is by means of one hook & eye centered on the band 1½” from the finished edge. Center of horizontal buttonhole will be set ¾” in from the folded edge of band.

BELT LOOPS: Belt loops measuring ½” wide finished will be bar tacked at top and bottom. Loop opening measures 1¾”. Belt loops are bar tack set top and bottom. Loop placement is as follows: 7-loops 3 each side (evenly spaced) one on seat seam

FLY: Right fly will have a folded extension serged at the side and bottom with the zipper sandwiched between the extension seam. Folded right fly measures 1¾”. Left fly will have a set facing with the side serged. Zipper will have bar tacks at bottom of left fly and at join seam over “J” stitch (2). Zipper lengths are as follows:

Size Length 28.36 7” 38 – up 9”

FRONT POCKETS: Front pockets are Patch Pocket Style. Pocket is attached to the front and double needle top stitched. Pockets will have horizontal bar tacks at top and vertical at side seam of pocket opening.

HIP POCKETS: Pants will have a left and right hip patch pocket. Hip pockets will have a flap style pocket button closure. Pocket opening measures 5½”; corners are bar tacked. Both pockets will have a button flap closure. Pocket and pocket flap are double needle stitched.

FLAPS: Pockets have flaps with fusible interlining. Flaps are cut two pieces, ¼” double needle stitched. Pocket flaps are double needle set.

HEM: Shorts will be single needle lockstitch hemmed and finish ½” wide with fold under. Inseam will finish at 7”.

TOLERANCES: Allowed for the above measurements are as follows:

MEASUREMENT RANGE TOLERANCES 0” – 6” ±⅛” 6” – 12” ±¼” 12” – 24” ±½” Over – 24” ±¾”

LABELING: Print Label

FINISHING: Each garment will be trimmed, inspected, and neatly folded.

5.1.6: SHIRT, LONG SLEEVE, DRESS, ZIPPER STYLE FOR MEN

FABRIC: Milliken, Fabric #7025 or Department approved equivalent. 100% texturized Dacron polyester (featherweight) gabardine weave. 2 x 1 construction, 7.0 oz. per linear yard of 4.3 oz (+ or - .25) per square yard. Fast color, guaranteed washable, with minimum shrinkage. Permanent press, subject to washing care instruction. Fabric to include VISA finish, a soil release that combines with it color bright retention and moisture absorbency for maximum comfort.

COLOR: Light Green (Lagoon) Shade #2534 or Department approved equivalent.

STYLE: Long sleeve permanent press police shirt with concealed zipper front and convertible collar, tapered form fit. Collar and sleeve length size to be in 14 – 14¼ thru 20, with sleeve lengths from 32 thru and including 37, as per size charts as listed below. Stitched-in military creases.

COLLAR: Convertible style collar - points approximately 3¼’ long; top stitched 3/16” from edge; die cut with permanent heat tacked collar stays with a two piece yoke 3” deep. Outside yoke top-stitched. Inside yoke and Banana to have lining.

FRONT: To have 1½” placket on top center front. Zipper to be sandwiched and to extend from the second to the sixth buttonhole with the stitch to be concealed under the center strip. Front to have (7) buttons and buttonholes.

FLAPS: One piece, die cut and creased to ensure uniformity. Flaps are to measure a minimum of 5½” wide and be 2½” long at sides, and a minimum of 2¾” long at center point with deep scallops, with gripper snaps on underside of flap and on pocket. Snaps are not to be visible on top of the flap. Hand sewn or dressmaker snaps will not be acceptable. Pencil division through both flaps. Flap to be lined with 100%/Dacron lining. Flaps to have button sewn on top approximately 5/8” above points. Flaps to have 1/16” stitched center crease.

POCKETS: Die cut and creased to ensure uniformity. Two breast pockets with ½” hem; 1½” box pleats stitched to prevent spreading. Pockets to be a minimum of 5½” deep and 5¼” wide with mitered corners. Both pockets to have pencil division 1½”. Each pocket to have 1/16” stitched-in creases.

BADGE Inside sling type badge holder of self goods approximately 1-1/2” wide to extend from SLING: joining seam to pocket of left front. Two small buttonholes, approximately 1” apart with the lower buttonhole approximately 1” above the flap.

SLEEVES: One piece with top placket a minimum of 1” wide, button placket ½” wide. Plackets to be a minimum of 4 ½” long from top of cuff with opening approximately 5”. One

button and buttonhole on sleeve facings. Each sleeve shall have an elbow reinforcement extending to top of cuff. The sleeves must be secured to the body of the shirt by means of a merrow stitch with a safety stitch so as to properly strengthen the stitch.

CUFFS: Minimum 2½” wide with ½” hem; and approximate 3/16” top stitching. Double buttons with corresponding buttonholes, approximately 1” apart, on each cuff.

FINISHED LENGTH SIZES

COLLAR SIZE CUFF LENGTH 14-14 ½ 10” 15-15 ½ 10-1/2” 16-16 ½ 11” 17-17 ½ 11-1/2” 18-18 ½ 12” 19 or more 12”

SHOULDER STRAPS (EPAULETS): To measure 2” at sleeve head and tapered to approximate 1⅝” at ends which are pointed approximate 1”. Straps to be stitched to shoulders by single needle machine forming and X. Length of straps to graduated conforming to size of shirt. Buttons attached to yokes to match shoulder strap buttonholes.

STITCHED CREASE: There shall be one 1/16” stitched-in crease on each front and three 1/16” stitched- in creases on back. Flaps and pockets to have 1/16” stitched-in crease to give uniform shape and size.

BUTTONS: Buttons will be first quality pearlized polyester in a matching or coordination color, to withstand excess wear and laundering. Size will be a minimum 17 ligne and 4 hole style.

ZIPPER: Nylon separating zipper with nylon coil, matching binder seam, coordinated color for all components. All molded plastic.

THREAD: Spun polyester thread to match shirt fabric.

STITCHING: Sleeving and closing operation-overlock by means of a merrow stitch with a safety stitch so as to properly strengthen the seam. All stitches must be of the proper tension and size to avoid puckering after the shirt has been laundered and to give best durable press performance.

CUTTING: Collars, band, pockets, shoulder straps and flaps to be die cut to insure uniformity.

PRESSING: Component parts must be pressed on hothead machines; finished shirts to be folded and hand pressed, using jet clips.

PACKING: Shirts to be shipped in poly bags and three shirts to a box with sizes marked on outside of box at one end.

EMBLEMS: There is to be and official Division of Recreation and Parks emblem sewn on each sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor. Specifications attached.

5.1.7: SHIRT, LONG SLEEVE, DRESS, ZIPPER STYLE FOR WOMEN

FABRIC: Milliken, fabric #7025 or Department approved equivalent. 100% texturized Dacron polyester (featherweight) gabardine weave. 2 x 1 construction, 7.0 oz. per linear yard or 4.3 oz. (+ or - .25) per square yard. Fast color, guaranteed washable, with a minimum shrinkage. Permanent press, subject to washing care instructions. Fabric to include VISA finish, a soil release that combines with it color bright retention and moisture absorbency for maximum comfort.

STYLE: Long sleeve permanent press women’s police style blouse with zipper and collar, tapered form fit. Stitched-in military creases.

COLLAR: Convertible type points approximately 3½” long; top stitched 3/16” from edge. Die cut. Permanent heat tacked collar stays with a two piece yoke a minimum of 2½” deep. Outside yoke top stitched. Banana and inside yoke to have lining of 100% satin polyester.

FRONT: To have 1½” placket on top center front. Zipper to be sandwiched and extended from third to the fifth buttonhole with stitch to be concealed under the center strip. Front to have (6) buttons and buttonholes.

FLAPS: One piece, die cut and creased to insure uniformity. Two flaps a minimum of 4¾” wide, 1¾” long at sides and a minimum of 2¼” long at the center with deep scallops, with gripper snap on underside of flap. Hand sewn or dressmaker snaps will not be acceptable. Pencil division through both flaps. Flap to be lined with 100% Dacron lining. Flaps to have button sewn on top approximately ¼” above point. Flaps to have 1/16” stitched in center crease.

POCKETS: Die cut and creased to insure uniformity. Two breast pockets with a minimum of ¾” box pleats stitched to prevent spreading. Approximately 4¾” deep x 4⅝” wide with mitered corners. Both pockets to have pencil division 1”. Gripper snaps at top corners to match flaps snaps. Each pocket to have 1/16” stitched-in creases.

BADGE SLING: Inside sling type badge of self goods approximately 1½” wide to extend from joining seam to pocket of left front. Two small buttonholes, 1” apart with the lower buttonhole approximately 1” above flap.

SLEEVES: One piece with top placket 1” wide and under placket ½” wide both of the same materials as garments. Placket to be approximately 5½” long x 4½” wide with mitered corners. The sleeves must be secured to the body of the shirt by means of merrow stitch with a safety stitch so as to properly strengthen stitch.

CUFF: To measure a minimum of 2½” wide interlined. Button on cuff. To have ⅛” edge stitched.

SHOULDER STRAPS (EPAULETS): To measure approximately 2” at sleeve head and tapered to 1¾” at ends which are pointed 1”. Straps to be stitched to shoulders by single needle machine forming an “X”. Length of straps to be graduated conforming to size of blouse. Buttons attached to yokes to match shoulder strap buttonholes.

STITCHED CREASE: There shall be one 1/16” stitched-in crease on each front and three 1/16” stitched creases on back. Flaps and pockets to have 1/16” stitched-in creases to give uniform shape and size.

BUTTONS: Buttons will be first quality pearlized polyester in a matching or coordinating color, to withstand excess wear and laundering. Size will be a minimum of 17 ligne and 4 hole style.

STITCHING: Sleeving and closing operations-overlock by means of a merrow stitch with a safety stitch so as to properly strengthen the seam. All stitches must be of the proper tension and size to avoid puckering after the shirt has been laundered and to give best durable press performance.

CUTTING: Collars, pockets, shoulder straps and flaps to be die cut to ensure uniformity.

PRESSING: Component parts must be pressed on hothead machines; finished blouses to be folded and hand pressed, using jet clips.

PACKING: Shirts to be shipped in poly bags and three blouses to a box with sizes marked on outside of box at one end.

EMBLEMS: There is to be an official Division of Recreation and Parks emblem sewn on each sleeve of the shirt 1” below the shoulder seam. Emblems to be furnished by vendor. Specifications attached.

5.1.8: SHIRT, SHORT SLEEVE, DRESS, ZIPPER STYLE FOR MEN

FABRIC: Milliken, fabric #7025 or Department approved equivalent. 100% texturized Dacron polyester (featherweight) gabardine weave. 2 x 1 construction 7.0 oz. per linear yard or 4.3 oz. (+ or -.25) per square yard. Fast color guaranteed washable. Permanent press, subject to washing care instruction. Fabric to include VISA finish, a soil release that combines with it color bright retention and moisture absorbency for maximum comfort. Color shall be rated 4.0 on 20 hour lightfastness, laundering and against perspiration shade change with a minimum shrinkage.

STYLE: Short sleeve permanent press police shirt with concealed zipper front and convertible collar. Collar to be in regular collar sizes 14 thru 20, not small, medium or large. Tapered form fit. Stitched-in military creases.

COLLAR: Convertible type points approximately 3½” long, top stitched 3/16” from edge. Die cut. Permanent heat tacked collar stays with two piece yoke, 3” deep. Outside yoke top stitched. Banana and inside yoke to have lining of 100% satin polyester.

FRONT: To have 1½” placket on top center front, zipper to be sandwiched and to extend from the second to the sixth buttonhole with the stitch to be concealed under the center strip. Front to have seven buttons and buttonholes. Fronts to be faced on each underside with no less than 2½” + or –⅛” turned under of shirt material.

FLAPS: One piece, die cut and creased to ensure uniformity. Two flaps a minimum of 5½” wide approximately 2½” at sides, snaps or underside of the flap. Hand sewn or dressmaker snaps will not be acceptable. Pencil division through both flaps. Flap to be lined with 100% Dacron lining. Flaps to have horizontal buttonhole ⅝” above point. Flaps to have 1/16” stitched-in center crease.

POCKETS: Die cut and creased to insure uniformity. Two breast pockets with ¼” hem; 1½” box pleats, stitched to prevent spreading. Approximately 6” deep by 5⅜” wide with mitered corners. Both pockets to have pencil division 1½”. Each pocket to have 1/16” stitched-in center crease.

BADGE SLING: Inside sling-type badge patch of self goods approximately 1½” wide to extend from joining seam to pocket of left front. Two horizontal buttonholes, approximately 1” apart with the lower buttonhole approximately 1” above flap.

SLEEVES: One piece 9¾” to 10” in length with ¾” hem. The sleeves must be secured to the body of the shirt by means of a merrow stitch with a safety stitch so as to properly strengthen the stitch.

SHOULDER STRAPS (EPAULETS): To measure 2” at sleeve head and tapered to approximately 1⅝” at ends which are to be pointed approximately ⅞”. Straps to be stitched to shoulders by single

needle machine forming an “X”. Length of straps to be graduated conforming to size of shirt. Buttons attached to yokes to match shoulder straps buttonholes at pointed ends.

STITCHED CREASE: There shall be one 1/16” stitched-in crease on each front and three 1/16” stitched- in creases on back. Flaps and pockets to have 1/16” stitched-in crease to give uniform shape and size.

BUTTONS: Buttons will be of first quality pearlized polyester in a matching or coordinating color to withstand excess wear and laundering. Size will be 17 ligne and 4 hole style.

ZIPPER: Nylon separating zipper, with nylon coil, matching binder seam, coordinated color for all components. All molded plastic zipper.

STITCHING: Sleeving and closing operation-overlock with safety stitch so as to properly strengthen the seam. All stitches must be of the proper tension and size to avoid puckering after the shirt has been laundered and to give best durable press performance.

CUTTING: Collars, pockets, flaps and shoulder straps and flaps to be die cut to ensure uniformity.

PRESSING: Component parts must be pressed on hot head machines; finished shirts to be folded and pressed using jet clips.

PACKING: Shirts to be shipped in poly bags and three shirts to the box with sizes marked on outside of box at one end.

EMBLEMS: There is to be an official Division of Recreation and Parks emblem sewn on each sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor. Specifications attached.

5.1.9: SHIRT, SHORT SLEEVE, DRESS, ZIPPER STYLE FOR WOMEN

FABRIC: Milliken, fabric #7025 or Department approved equivalent. 100% texturized Dacron polyester (featherweight) gabardine weave. 2 x 2 construction, 7.0 oz. per linear yard or 4.3 oz. (+ or -.25) per square yard. Fast color, guaranteed washable. Permanent press, subject to washing care instruction. Fabric to include VISA finish, a soil release that combines with it color bright retention and moisture absorbency for maximum comfort and minimum shrinkage.

STYLE: Short sleeve permanent press women’s police style blouse with zipper and collar, tapered to fit. Stitched-in military creases.

COLLAR: Convertible type points approximately 3½” long, top-stitched 3/16” from edge. Die cut. Permanent heat tacked collar stays with two piece yoke. Outside yoke top stitched. Banana and inside yoke to have lining of 100% satin polyester.

FRONT: To have 1½” placket on top center front, zipper to be sandwiched and to extend from the third to the fifth buttonhole with the stitch to be concealed under the center strip. Front to have (6) buttons and buttonholes.

FLAPS: One piece, die cut and creased to ensure uniformity. Two flaps approximately 5” wide, 2” long at sides and minimum of 1¼” long at center with deep scallops, with gripper snaps on underside of the flap. Hand sewn or dressmaker snaps will not acceptable. Pencil division through both flaps. Flap to be lined with 100% Dacron lining. Flaps to have button sewn on top approximately ¼” above point. Flaps to have 1/16” stitched-in center crease.

POCKETS: Die cut and creased to insure uniformity. Two breast pockets with approximately 1” box pleats stitched to prevent spreading. Approximately 4¾” deep x 4⅝” wide with mitered corners. Both pockets have pencil division. Gripper snaps at top corners to match flap snaps. Each pocket to have 1/16” stitched-in creases.

BADGE SLING: Inside sling-type badge patch of self goods approximately 1½” wide to extend from joining seam to pocket of left front. Two small buttonholes, approximately 1¼” apart with the lower buttonhole approximately 1” above flap.

SLEEVES: The short sleeves are to be cut in one piece and are to measure approximately 8¼” long from shoulder and approximately 4” long from underarms. The sleeve must be secured to the body of the shirt by means of a merrow stitch with a safety stitch so as to properly strengthen the seam. The hem is to be approximately ¾” wide and is to be turned under, no raw edges exposed.

BACKS: Wide double yoke. Yoke to be approximately 2½” wide at center point, 1¼” wide on each end where joined into sleeve. To be single stitched 1/16”.

SHOULDER STRAPS (EPAULETS): To measure 2” at sleeve head and tapered to approximately 1⅝” at ends which are to be pointed approximately ⅞”. Straps to be stitched to shoulders by single needle machine forming to size of blouse. Buttons attached to yokes to match shoulder strap buttonholes at pointed ends.

STITCHED CREASE: There shall be one 1/16” stitched-in crease on each front and three 1/16” stitched- in creases on back. Flap and pockets to have 1/16” stitched-in crease to give uniform shape and size.

BUTTONS: Buttons will be of first quality pearlized polyester in a matching or coordinating color to withstand excess wear and laundering. Size will be 19 ligne and 4 hole style.

THREAD: Spun polyester thread to match shirt color with sizes marked on outside of box at one end.

STITCHING: Sleeving and closing operation-overlock with safety stitch.

CUTTING: Collars, pockets, shoulder straps and flaps to be die cut to ensure uniformity

PRESSING: Component parts must be pressed on hot head machines; finished shirt to be folded and pressed using jet clips.

PACKING: Shirts to be shipped in poly bags and three shirts to a box with sizes marked on outside of box at one end.

EMBLEMS: There is to be an official Division of Recreation and Parks emblem sewn on each sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor. Specifications attached.

5.1.10: SHIRT, SHORT SLEEVE, WORK FOR MEN

DESCRIPTION: Male S/S Public Safety Shirt

SIZES: 14½ - 22½

COLOR: Greentone w/Spruce Shoulder Straps

FABRIC: 65% Polyester/35% Cotton

CONSTRUCTIONS/DETAILS:

COLLAR: Convertible collar is cut two pieces and will have Harodite woven interlining and collar stays. Collar points have 2¼” long collar stays. Collar stays will be placed in the front edge of the collar and stitched through and through. Collar is single needle set and closed to yield a clean finish. Collar is top stitched. Inside collar will have a self fabric (mock band) reinforcement single needle edge stitch set the inside.

LANYARD WHISTLE SUPPORTS/EPAULETS: Shirt has shoulder epaulets with non-woven fusible interlining. Epaulets are pressed, edge stitched and set into sleeve seams and partly stitched to the garment by means of crisscross diagonal box stitching 1½” onto the shirt. Finished epaulets measure 2” wide at armhole seam and taper to 1½” wide at the point.

Note; point of the epaulet will finish ½” from the collar seam. Ends are formed to a point and will have a buttonhole closure with a Ligne 19 button set on the shoulder. Button is stitched at the edge of a cut buttonhole eyelet, which allows passage of Lanyard/whistle cord to the whistle supports. Lanyard supports are sewn into the collar seam and to shoulder seam of shirt. Support is 1” wide self- fabric.

BADGE SLING: Shirt will have a 1½” wide self-fabric badge sling. Sling is single needle set to the pocket, through the eyelets, and set into the shoulder seam. Badge sling is folded and merrowed on one side.

EYELETS: Shirt will have two horizontal eyelets centered on the left breast, over the stitched creasing and positioned so that the lower eyelet is 1¼” above the pocket flap and 1¼” apart.

POCKETS: Shirt will have two (2) breast pockets with flaps and velcro closures. Pocket has a center box pleat. Box pleat is 1½” wide. Stitched creasing down the center of the box pleat. Pocket is double needle set with mitered corners. Both left and right pockets and flaps will have a 1½” wide pencil slot running top to bottom. Pocket hem is single needle lockstitch hemmed and finishes ¾” wide with fold under. Finished pocket meaures 6” wide by 5¾” deep. Top corners of pocket and pencil stitch are bar tacked.

FLAPS: Standard men’s die cut pocket flaps are scalloped and will have non-woven fusible interlining on bottom side of flap, with double needle stitching around the edges. Flap is double needle stitched to the shirt. Both left and right pockets and flaps will have an 1½” wide pencil slot running top to bottom. Flap will have one (1) Ligne 19 button, centered and set ½” from scallop edge (button has no closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn beneath the mock button closure, to permit feeding of the lanyard cord and whistle. Finished pocket flaps will measure 2¾” on each end and 2⅞” at the center point. Stitched creasing runs along center of flap and aligns with pintuck stitch on box pleat (pocket).

VELCRO: Flaps and pockets effect closure by means of four (4) strips of Velcro. Strips are 1” long by ½” wide. The hook side of the Velcro is single needle set on the pocket, and the loop side of the Velcro is single needle set on the under side of the flap. Velcro on the pocket is set ⅜” below the finished edge of the pocket, and ¼” in from the finished side of the pocket.

PLACKET/FACINGS: Both facings will be folded and merrowed. The left front will be folded to create a 1½” wide placket with 250-edgelock interlining. Placket is top stitched on both sides. Facings on both sides are merrowed on the outside edges.

CREASING: Shirt will have two (2) rows of stitched creasing on the front of the shirt. Creasing extends from shoulder seams, through pocket flaps, and pockets to bottom of shirt.

SLEEVES: Shirt will have short sleeves. Sleeve hem in single needle lockstitch hemmed and finishes ¾” wide with fold under. Ends of sleeve seams are bar tacked. Armhole seams are pressed and double needle topstitched.

YOKE: Yoke is cut 2-plyt and is clean finished on the inside. Inside yoke is cut of satin taffeta. Maritn Woven Label is set to the lining only. Back yoke seam is double needle topstitched.

UNDERARM EYELETS: Sleeve underarm will have four (4) round 101 (vented) eyelets under the arm. Eyelets will be placed as follows: one on each side of the sleeve (front/back) 1” above the armhole seam and one on each side of the body (front/back) 1” below the armhole seam. All four (4) eyelets will be placed diagonally 1” from the seam intersection (:+:).

BACK: Back is cut one (1) piece with three (3) rows of creasing. One row at center back and one row on each side spaced evenly apart.

CLOSURE: Front closure is by means of seven (7) Ligne 19 buttons and one (1) separating zipper. First button is set ½” below the collar seam, second button is spaced 4” below the collar seam. All remaining buttons are spaced 3½” apart. First buttonhole is horizontal. All remaining buttonholes are vertical. Note: Only the first, second and seventh (last) buttons are working buttons. The third, fourth, fifth and sixth buttons are mock buttons. The shirt will have a concealed 16” black separating zipper set beneath the front placket. Zipper is single needle lockstitch set 4” below the collar seam.

HEM: Bottom hem is single needle lockstitch hemmed ¼” wide, shirt tail hem.

Measurements: 14 14½ 15 15½ 16 16½ 17 17½ 18½ 19½ 20½ Chest 40½ 42½ 44½ 46½ 48½ 50½ 52½ 54½ 58½ 62½ 66½ Across Back 20½ 21½ 22½ 23½ 24½ 25½ 26½ 27½ 29½ 31½ 33½ Across Shoulder 17 17½ 18 18½ 19 19½ 20 20½ 21½ 22½ 23½ Sleeve Outseam 9 9¼ 9½ 9¾ 10 10¼ 10½ 10¾ 11¼ 11¾ 12¼ Sleeve Inseam 6½ 6½ 6½ 6½ 6½ 6½ 6½ 6½ 6½ 6½ 6½ Collar 14 14½ 15 15½ 16 16½ 17 17½ 18½ 19½ 20½ Length 32¼ 32½ 32¾ 33 33¼ 33½ 33¾ 34 34¾ 35 35½

TOLERANCES: Allowed for the above measurements are as follows:

MEASUREMENT RANGE TOLERANCES 0” – 6” ±⅛” 6” – 12” ±¼” 12” – 24” ±½”

Over – 24” ±¾”

LABELING: White Woven Label

FINISHING: Each garment will be trimmed, inspected, pressed and neatly folded.

5.1.11: SHIRT, SHORT SLEEVE, WORK FOR WOMEN

Description: Female S/S Public Safety Shirt

Color: Greentone w/Spruce Shoulder Straps

Fabric: 65% Polyester 35% Cotton Poplin

CONSTRUCTION / DETAILS: Collar: Convertible collar is cut two pieces, and will have fusible interlining, and collar stays. Collar stays are single needle lockstitch set to the under side of the collar. Collar is single needle set and closed to yield a clean finish. Collar is top stitched.

Placket/Facings: Both facings will be folded and merrowed. The right front will be folded to create a 1½" wide placket with 250-edgelock interlining. Placket is top stitched on both sides. Facings on both sides are merrowed on the outside edges.

Pockets: Shirt will have two (2) breast pockets with flaps, and Velcro closures. Pocket has a center box pleat. Pintuck stitching runs down center of box pleat. Pleat is 1" wide. Pocket has mitered corners. Top of pocket is single needle lockstitch hemmed and finishes ¾" wide with fold under. On the inside of each pocket will be a single needle dividing stitch 1½" wide to form pencil slot.

Flaps: Pocket flaps are scalloped and will have fusible interlining on under side of flap, with clean-finished edges. Flap is double needle stitched to the shirt. Both left and right pockets and flaps will have a 1½" wide pencil slot running top to bottom. Flap will have one (1) Ligne 19 button, centered and set ½" from scallop edge (button has no closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn beneath the mock button closure, to permit feeding of the lanyard cord. Stitched creasing runs along center of flap and aligns with stitched crease on box pleat (pocket). Finished pocket flaps will measure 2- ¼” on each end and at the center point.

Velcro: Flaps and pockets effect closure by means of four (4) strips of matching Velcro. Two strips of Velcro (hooks) are located at top of pocket corners, which effect closure with corresponding Velcro (loops) on inside of pocket flaps. Velcro strips measure 1" x ⅜”. Length direction is set vertically on pockets. Velcro is placed so that the top is on the edge of hemmed pocket, and outer edge is ¼" from edge of pocket. Hook side of Velcro is on pocket; loop side of Velcro is on the pocket flap. Underside of flaps have a 1"x ⅜” piece of Velcro (loop). Velcro on flap underside is placed ¼" from scalloped edge and ⅜” from sides.

Badge Sling: Shirt has a 1½" wide self-fabric badge support attached to shoulder seam and sewn into back of pocket. Badge sling is folded and merrowed on one side (Badge sling is on left side only).

Eyelets: Shirt has badge eyelets set above left side pocket flap. Eyelets are set horizontally. Eyelets are centered on stitched crease and are sewn through shirt and badge sling. Eyelets are located 1¼" above edge of pocket flap and set 1 ¼" apart.

Sleeves: Shirt will have short sleeves. Sleeve hem in single needle lockstitch hemmed and finishes ¾” wide with fold under. Ends of sleeve seams are bar tacked. Armhole seams are pressed and double needle topstitched.

Creasing: Shirt front will have stitched creasing sewn down both sides of the shirt. Stitched creasing extends from shoulder seam through pocket flaps, and pockets, to bottom of the shirt.

Closure: Front closure is by means of six, (6) Ligne 19 matching Pearl buttons. First button is set ½" below the collar seam, (on left side) with a horizontal buttonhole. All remaining buttonholes are vertical. The remaining button on the shirt is spaced 3½" apart.

Back: Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creases down back, extending from the yoke to bottom of shirt. First stitched crease is at center back of shirt and one on each side of center crease, evenly spaced. Yoke is clean finish set to the inside. Label is set to the lining (only). Martunique Label.

Lanyard Whistle Supports/Epaulets: Shirt has shoulder epaulets. Epaulets are set into sleeve seams and partly stitched to the garment by means of crisscross diagonal stitching. Rest of epaulet is unattached. Ends are formed to a point and have a buttonhole that effects closure with a Ligne 19 button set on the shoulder. Finished epaulets measure 2” wide at shoulder seam and taper 1½” wide at the point. Button is stitched at the edge of a cut buttonhole eyelet, which allows passage of Lanyard/whistle cord, to the whistle supports (one on each side). Lanyard supports are sewn into the collar seam and to shoulder of shirt. Support measures 1" wide by 2¼" long.

Hem: Bottom hem is ¼" single needle lockstitch set.

5.1.12: SHIRT, LONG SLEEVE, WORK FOR MEN

Description: Male L/S Public Safety Shirt

Sizes: 14 1/2 – 22 ½

Color: Greentone w/Spruce Shoulders Straps

Fabric: 65% Polyester/35% Cotton

CONSTRUCTION/DETAILS:

Collar: Banded collar is cut two (2) pieces and will have Harodite woven fusible and collar stays. Collar points will have 2 ¼” long collar stays. Collar stays will be placed in the front edge of the collar and stitched through and through (with ¼” topstitching) Collar is topstitched. Band has 2-ply non-woven fusible interlining, inside collar band is cut of self material. Band is single needle set and closed. Collar band has one horizontal buttonhold and one (1) Ligne 19 button.

Placket: Left side has a 1 ½” wide placket with edgelock interlining. Placket is top stitched on each side. Right side is hemmed clean finished to the inside of the shirt with a ¾” hem.

Flaps: STANDARD MEN’S DIE CUT Pocket flaps are scalloped and will have non woven fusible interlining on bottom side of flap, with double needle stitching around the edges. Flap is double needle stitched onto the shirt. Both left and right pockets and flaps will have a 1/ ½” wide pencil slot running top to bottom. Flap will have on (1) Ligne 19 button, centered and set ½” from scallop edge (button has no closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn beneath the mock button closure, to permit feeding of the lanyard cord and whistle. Finished pocket flaps will measure 2 ¾” on each end and 2 7/8” at the center point. Stitched creasing runs along center of flap and aligns with stitched creasing on box pleat (pocket).

Velcro: Flaps and pockets effect closure by means of four (4) strips of Velcro. Strips are 1” long by ½” wide. The hook side of the Velcro is single needle set on the pocket, the loop side of the Velcro is single needle set on the under side of the flap. Velcro on the pocket is set 3/8” below the finished edge of the pocket, and ¼” in from the finished side of the pocket.

Badge Sling: Shirt has a 1/ ½” wide self-fabric badge support attached to shoulder seam and sewn into back of pocket. Badge sling is folded and merrowed on one side (Badge sling is on left side only).

Eyelets: Shirt has badge eyelets set above left side pocket flaps. Eyelets are set horizontally. Eyelets are centered on stitched creasing and are sewn through shirt and badge sling. Eyelets are located 1/ ¼” above edge of pocket flap and set 1 ¼” apart. Eyelets measure 3/8” long.

Sleeves: Shirt will have long sleeves with elbow patch, adjustable cuffs and Hathaway type placket. Sleeves terminate with 2-ply cuffs. Cuffs have non-woven fusible interlining. Cuffs are double needle top stitched and there will be two rows of stitching on the set cuff operation. Cuffs finish 3” wide. Cuff adjustability is by means of two (2) rows of buttons, with two (2) buttons for each row (4 buttons). Ligne 19 white buttons. Buttons effect closure with one (1) row of buttonholes. (2 buttons per-row). Button spacing: first row is set ½” from edge. Second row is set 1 ¼” apart. Note: buttons are 1 ¼” apart (vertically). Armhole seams are pressed and double needle top stitched.

Sleeve Placket: Hathaway type placket. Top side of placket is 2 ¼” wide and single needle bound set to the shirt. Underside of placket is ½” wide and single needle bound set. Vent opening is 4 ½”. One buttonhole on topside of placket effects closure with one Ligne 19 button on placket underside. Button is located 2 ¼” above cuff seam.

Banjo Pad: Each sleeve has a “banjo style” elbow patch. Elbow patch has rounded edges, and is flat at the bottom. Elbow patch is superimposed on sleeve so that the bottom side (flat side) joins the sleeve placket. Finished elbow patch measure 7” long. Elbow patch is edge stitch set.

Underarm Eyelets: Sleeve underarm will have four, (4) round 101 (vented) eyelets under the arm. Eyelets will be placed as follows: one on each side of the sleeve (front/back) 1” above the armhole seam and one on each side of the body (front/back) 1” below the armhole seam. All four (4) eyelets will be placed diagonally 1” from the seam intersection (:+:) . Lanyard Whistle Supports/Epaulets: Shirt has spruce shoulder epaulets with non woven fusible interlining. Epaulets are pressed, edge stitched and set into sleeve seams and partly stitched to the garment by means of crisscross diagonal stitching onto the shirt 1 ½”. Finished epaulets measure 2” wide at the armhole seam and taper 1/ ½” wide at the point, ½” from edge of collar. Ends are formed to a point and have a buttonhole that effects closure with a Ligne 19 button set on the shoulder. Button is stitched to the shoulder edge of a cut buttonhole eyelet, which allows passage of Lanyard/whistle cord, to the whistle supports (one on each side). Self-fabric lanyard supports are sewn into the collar seam and to shoulder of shirt. Support measures 1” wide by 2 ¼” long.

Creasing: Shirt will have stitched creasing sewn down both sides of the shirt. Stitched creasing extends from shoulder seam though pocket flaps, and pockets, to bottom of the shirt.

Closure: Front closure is by means of seven, (7) Ligne 19 buttons, and one (1) 16” separating zipper. First button is set on the collar band with a horizontal buttonhole. All remaining buttonholes are vertical. The second button on the shirt is spaced 3” below the collar band seam. All remaining buttons are spaced 3 1½”apart. Note: Only the first, second, and seventh (last) buttons, are working buttons. The third, fourth, fifth, an sixth buttons are mock buttons. The shirt will have a concealed 16” separating zipper set beneath the front placket. Zipper is single needle lockstitch set, 4” below the collar seam.

Back: Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creasing down back, extending from the yoke to bottom of shirt. First crease stitch is at center back of shirt and one on each side of center crease, evenly spaced.

Yoke: Yoke is clean finish set to the inside; inside yoke is satin taffeta. Woven Comfort in Action Label is set to the satin taffeta lining (only). Back yoke seam is double needle topstitched.

Hem: Bottom hem is single needle lockstitch hemmed and finishes ¼” with fold under.

Sleeve Length: 14 ½ 15 15 ½ 16 16 ½ 17 17 ½ 18 ½ 19 ½ 20 ½ 32/33 x x x x x x x x x x 34/35 x x x x x x x x x x 36/37 x x x x x x x x x x

Measurements: 14 ½ 15 15 ½ 16 16 ½* 17 17 ½ Chest 42 ½ 44 ½ 46 ½ 48 ½ 50 ½ 52 ½ 54 ½ Across Back 21 ½ 22 ½ 23 ½ 24 ½ 25 ½ 26 ½ 27 ½ Slv Inseam 6 ½ 6 ½ 6 ½ 6 ½ 6 ½ 6 ½ 6 ½ Collar 14 ½ 15 15 ½ 16 16 ½ 17 17 ½ Waist 40 42 44 46 48 50 52 Sweep 43 ½ 45 ½ 47 ½ 49 ½ 51 ½ 53 ½ 55 ½ Length 32 ½ 32 ¾ 33 33 ¼ 33 ½ 33 ¾ 34

Measurements: 18 ½ 19 ½ 20 ½ Chest 58 ½ 62 ½ 66 ½ Across Back 29 ½ 31 ½ 33 ½ Slv Inseam 6 ½ 6 ½ 6 ½ Collar 18 ½ 19 ½ 20 ½ Waist 56 60 64 Sweep 59 ½ 63 ½ 67 ½ Length 34 ½ 35 35 ½

Tolerances: Allowed for the above measurements are as follows:

MEASUREMENT RANGE TOLERANCES 0” - 6” + 1/8” 6” – 12” +1/4” 12” – 24” + ½” Over – 24” + ¾”

Labeling: Comfort in Action Black Woven Label w/plain printed label attached at LEFT SIDE

Finishing: Each garment will be trimmed, inspected, pressed and neatly folded.

Emblems: Florida Parks Emblems to be sewn on both sleeves

5.1.13: SHIRT, LONG SLEEVE, WORK FOR WOMEN

Description: Ladies L/S Public Safety Shirt

Color: Greentone w/Spruce Shoulder Straps

Fabric: 65% Polyester 35% Cotton Poplin

CONSTRUCTION / DETAILS: Collar: Convertible collar is cut two pieces, and will have fusible interlining, and collar stays. Collar stays are single needle lockstitch set to the under side of the collar. Collar is single needle set and closed to yield a clean finish. Collar is top stitched.

Placket/Facings: Both facings will be folded and merrowed. The right front will be folded to create a 1½" wide placket with 250-edgelock interlining. Placket is top stitched on both sides. Facings on both sides are merrowed on the outside edges.

Pockets: Shirt will have two (2) breast pockets with flaps, and Velcro closures. Pocket has a center box pleat. Pin tuck stitching runs down center of box pleat. Pleat is 1" wide. Pocket has mitered corners. Top of pocket is single needle lock stitch hemmed and finishes ¾" wide with fold under. On the inside of each pocket will be a single needle dividing stitch 1½" wide to form pencil slot.

Flaps: Pocket flaps are scalloped and will have fusible interlining on under side of flap, with clean-finished edges. Flap is double needle stitched to the shirt. Both left and right pockets and flaps will have a 1½" wide pencil slot running top to bottom. Flap will have one (1) Ligne 19 button, centered and set ½" from scallop edge (button has no closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn beneath the mock button closure, to permit feeding of the lanyard cord. Stitched creasing runs along center of flap and aligns with stitched crease on box pleat (pocket). Finished pocket flaps will measure 2- ¼” on each end and at the center point.

Velcro: Flaps and pockets effect closure by means of four (4) strips of matching Velcro. Two strips of Velcro (hooks) are located at top of pocket corners, which effect closure with corresponding Velcro (loops) on inside of pocket flaps. Velcro strips measure 1" x ⅜”. Length direction is set vertically on pockets. Velcro is placed so that the top is on the edge of hemmed pocket, and outer edge is ¼" from edge of pocket. Hook side of Velcro is on pocket; loop side of Velcro is on the pocket flap. Underside of flaps have a 1"x ⅜” piece of Velcro (loop). Velcro on flap underside is placed ¼" from scalloped edge and ⅜” from sides.

Badge Sling: Shirt has a 1½" wide self-fabric badge support attached to shoulder seam and sewn into back of pocket. Badge sling is folded and merrowed on one side (Badge sling is on left side only).

Eyelets: Shirt has badge eyelets set above left side pocket flap. Eyelets are set horizontally. Eyelets are centered on stitched crease and are sewn through shirt and badge sling. Eyelets are located 1¼" above edge of pocket flap and set 1 ¼" apart.

Sleeves: Shirt will have long sleeves with adjustable cuffs and Hathaway type placket. Sleeves terminate with 2-ply cuffs. Cuffs have non-woven fusible interlining. Cuffs are ¼" top stitched and there will be two (2) rows of stitching on the set cuff operation. Cuffs finish

3" wide. Cuff adjustability is by means of two (2) rows of buttons, with two (2) buttons for each row (4buttons). Ligne 19 buttons. Buttons effect closure with one (1) row of buttonholes. (2 buttons per-row). Button spacing: first row is set ½" from edge. Second row is set 1¼" from edge and buttons are 1¼" apart (vertically). Hathaway type placket. Topside of placket is 2¼" wide and single needle bound set to the shirt. Underside of placket is ½" wide and single needle bound set. Vent opening is 4½". One buttonhole on topside of placket effects closure with one Ligne 19 button on placket underside. Button is located 2¼" from cuff.

Creasing: Shirtfront will have stitched creasing sewn down both sides of the shirt. Stitched creasing extends from shoulder seam through pocket flaps, and pockets, to bottom of the shirt.

Closure: Front closure is by means of six, (6) Ligne 19 matching Pearl buttons. First button is set ½" below the collar seam, (on left side) with a horizontal buttonhole. All remaining buttonholes are vertical. The remaining button on the shirt is spaced 3½" apart.

Back: Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creases down back, extending from the yoke to bottom of shirt. First stitched crease is at center back of shirt and one on each side of center crease, evenly spaced. Yoke is clean finish set to the inside. Label is set to the lining (only). Martunique Label.

Lanyard Whistle Supports/Epaulets: Shirt has shoulder epaulets. Epaulets are set into sleeve seams and partly stitched to the garment by means of crisscross diagonal stitching. Rest of epaulet is unattached. Ends are formed to a point and have a buttonhole that effects closure with a Ligne 19 button set on the shoulder. Finished epaulets measure 2” wide at shoulder seam and taper 1½” wide at the point. Button is stitched at the edge of a cut buttonhole eyelet, which allows passage of Lanyard/whistle cord, to the whistle supports (one on each side). Lanyard supports are sewn into the collar seam and to shoulder of shirt. Support measures 1" wide by 2¼" long.

Hem: Bottom hem is ¼" single needle lock stitch set.

5.1.14: SHIRT, KNIT

FABRIC: 50% Combed Cotton/50% Polyester with heavyweight pique knit. Color to be Lagoon Green.

STYLE: Boxed two button placket with matching buttons, and ribbed knit banded sleeve. Reinforced shoulder seam.

COLLAR: Fashion ribbed collar to be matching color in ribbed knit. To include taped reinforcement at back of neck.

EMBLEM: Florida Park Service Logo will embroidered on left front of shirt.

5.1.15: SHIRT, LONG SLEEVE, VOLUNTEER, GRAY FOR MEN/WOMEN

FABRIC: Poplin, 65% Dacron Polyester, 35% Combed Cotton fast color. Sanforized, average residual shrinkage does not exceed 2%. Precured Permanent Press with soil release finish. Wash and wear appearance with a minimum shrinkage.

COLOR: Gray, Shade #90810/11 or Department approved equivalent.

STYLE: Collar attached uniform shirt.

FRONT: To have approximate 1½” placket on top center front. Front to have seven buttons and buttonholes. Fronts to be faced on each underside with no less than 2½” +/- ⅛” turn under of shirt material.

BUTTONS: Minimum of 17 Ligne Pearlized Polyester buttons, matching shade of shirt. Buttonholes must be opened for those that are to be fastened.

FLAPS: Two scalloped flaps approximately 5½” wide, 2½” at sides, and 2¾” at center, die cut and creased to ensure uniformity of shape and size, lined with 100% Dacron interlining. 1” opening through both flaps adjacent to center plait for pencils. Each flap to have Velcro closure at both corners. Button sewn on top of flap.

POCKETS: Two breast pockets with approximately 1½ ” box pleats stitched to prevent spreading approximately 5¾” long by approximately 5 3/16” wide with mitered corners – pockets to be die cut and die creased in ensure uniformity of shape and size. Both pockets to have pencil division. Velcro closure on both pockets to match Velcro on flaps.

SLEEVES: One piece with top placket one inch wide and under placket ½” wide both of same material as garment. Plackets to be approximately 5” long from top of cuff. Sleeves should be tapered in proportion to finished measurements given below. Button and buttonhole on placket.

ELBOW REINFORCEMENT: Patches not less than 5½” x 4¾” with all four corners mitered to be set over sleeve placket on both sleeves. Patches to be die cut and die creased to ensure uniformity.

CUFF: To measure approximately 3” wide interlined. Double button cuffs approximately 1” apart between holes. To have approximately ⅛” edge stitch.

FINISHED LENGTH SIZES

COLLAR SIZE CUFF LENGTH 14½ to 15 10” 15½ to 16 10½ 16½ to 17 11” 17½ to 18 11½”

18½ or more 12”

COLLARS AND BANDS: Pressed stand-up collar and band. Collar points approximately 3⅜ long. Back of collar approximately 1¾” wide, collar stand approximately 1¼”wide. Collar to be die cut and die creased, band to be die cut. Permanent heat tacked collar stays. Collar shall be lined, with 100% Dacron interlining. To have 3/16” edge stitch.

BACKS: With double yoke approximately 1¾” from collar seam.

SHOULDER (EPAULETS): Straps to measure 2” at sleeve head tapered to approximately 1⅝” at ends which are to be pointed ⅞”. Point of straps to be approximately ½” from collar. Straps to be sewn down at the sleeve with single stitching. Straps to be stitched to shoulder with single needle machine forming an “X”. Buttons attached to shoulder to match strap buttonhole. Length of straps to be graduated to size of shirt.

STITCHING: Shirts shall have merrow stitching for sleeving operation and for closing operation. Balance of shirt to be single lock stitched.

CREASING: Wherever creasing is specified, the operation is to be performed on a heat machine using dies for absolute uniformity.

LENGTH: Minimum length for all sizes to be approximately 32½” measured from collar seam to bottom of tail center of back.

CUTTING: Collars, band, pockets, flaps, elbows reinforcements and cuffs to be die cut to ensure absolute uniformity.

FIT: To be tailored to chest and waist measurements of wearing personnel, and must be available in 2 body sizes for each neck size.

MEASUREMENTS: All of the above measurements are approximately, +/- ⅛”, and are from a size 14½, long sleeve shirt.

5.1.16: SHIRT, SHORT SLEEVE, VOLUNTEER, GRAY FOR MEN/WOMEN

FABRIC: Poplin, 65% Dacron Polyester, 35% Combed Cotton fast color. Sanforized, average residual shrinkage does not exceed 2%. Precured Permanent Press with soil release finish. Wash and wear appearance.

COLOR: Gray, Shade #90810/11 or Department approved equivalent.

STYLE: Convertible collar uniform shirt, in regular collar sizes 14 through 18, not small, medium, or large.

FRONT: To have 1½” placket on top center front. Front to have seven buttons and buttonholes. Fronts to be faced on each underside with no less than 2½” +/- ⅛” turn under of shirt material.

BUTTONS: Minimum of 17 Ligne Pearlized Polyester buttons, matching shade of shirt. Buttonholes must be opened for those that are to be fastened.

FLAPS: Two scalloped flaps approximately 5½” wide, 2½” at side and approximately 2¾” at center, die cut and creased to ensure uniformity of shape and size, lined with 100% Dacron interlining. 1” openings through both flaps adjacent to center plait for pencils. Each flap to have Velcro closure at both corners. Button sewn on top of flap.

POCKETS: Two pockets with approximately 1½” box pleats stitched to prevent spreading approximately 5¾” long by approximately 5 3/16” wide with mitered corner pockets to be die cut and die creased to ensure uniformity of shape and size. Both pockets to have pencil division. Velcro closure on both pockets to match Velcro on flaps.

SLEEVES: One piece measuring no less than 9½” on upper portion and no less than 6½” on lower portion, on size 14½; graduated according to size.

COLLAR: Convertible type with points 3½”. Single stitched approximately 3/16” lined with 100% Dacron interlining. Collar to be die cut and die creased. Collars to have permanently heat tacked stays and to be made in regular collar sizes.

BACKS: With double yoke approximately 1¾” from collar seam.

SHOULDER (EPAULETS): Straps to measure 2” at sleeve head tapered to approximately 1⅝” at ends which are to be pointed ⅞”. Point of straps to be approximately ½” from collar. Straps to be sewn down at the sleeve with single needle machine forming an “X”. Buttons attached to shoulder to match strap buttonhole. Length of straps to be graduated to size of shirt.

STITCHING: Shirts shall have merrow stitching for sleeving operation and for closing operation. Balance of shirt to be single lock-stitched.

CREASING: Wherever creasing is specified, the operation is to be performed on a heat machine using dies for absolute uniformity.

LENGTH: Minimum length for all sizes to be approximately 32½” measured from collar seam to bottom of tail center of back.

CUTTING: Collars and pockets and flaps to be die cut to ensure absolute uniformity.

FIT: To be tailored to chest and waist measurements of wearing personnel, and must be available in 2 body sizes for each neck size.

MEASUREMENTS: All of the above measurements are approximate, plus or minus 1/8”, and are from a size 14 ½, short sleeve shirt.

5.1.17: TEE SHIRT, VOLUNTEER

Hanes cotton “Beefy-Tee” tee shirt, or Department approved equivalent. Ash in color, crew neck with pocket on left front with Volunteer plus Florida Park Service Logo silk screened in black on pocket.

5.2.1: JACKET, DRESS/WORK

COLOR: Spruce Green

SHELL FABRIC: The Shell fabric shall be Tactel - 100% two ply Nylon with a water repellent finish.

PERMANENT SHELL LINING: Cloth type: 100% Nylon Tafetta, 70 Denier wrap and fill, color black, coating – WeatherTech Waterproof/Breathable.

All lining joining seams shall be safety stitched and then sealed with 1” heat sealed tape to prevent leakage. The tape shall be applied by hot air method. The tape shall not be affected by weather, temperature or storage. All stitching through the lining shall be sealed with waterproof tape. The lining shall extend through the top collar of the shell garment to form a waterproof barrier. There shall be 2 female snaps at the seam joining point and opposite, approximately 2 ¼” from the sleeve bottom, to attach to the removable liner. There shall be an inside storage pocket of shell material on the left side of the lining measuring approximately 8 ½” deep by 7” wide. The pocket shall be taped at all points where the pocket is attached to prevent leakage.

ZIP OUT LINER: The lining fabric shall be made of Thinsulate by 3M, 100% nylon taffeta from Dupont, 104 x 86 thread count per square inch quilted 200 gram/body with 100/gram sleeves. Backing shall be 100% nylon taffeta from Dupont, 104 x 86 thread count per square inch.

The liner shall have long sleeves and knit wristlets with tab and loop to accept anchor buttons or anchor strap. The entire body shall be bound with 1 9/16" nylon bias binding. The side seams, shoulder seams and sleeve seams shall be joined with a serge-sew safety stitch machine. The armhole will have a knit insert to allow freedom of movement. The pocket shall be 1 lower right inside patch pocket. The pocket shall be bound with 1 9/16" nylon bias binding and shall be attached with a single needle machine.

There shall be an interlining molded nylon zipper, center marked, and interchangeable attached to the liner. The zipper shall be of sufficient length to be satisfactorily attached to the facing of the jacket.

DESIGN: The jacket shall be a full cut, waist length model with a double outside fly of self goods covering a 2 way zipper front, Thinsulate zip-in, zip-out liner, shirred waistband, and zippered side vents. Coat construction shall be used throughout with body and sleeves being fully lined.

BODY DETAIL: The pocket shall be plain with patch pockets, flaps and badge tab. The inside facings shall be made of outer shell fabric and are to be sewn on top of the nylon lining that extends to the front edge of the jacket. There shall be a bi-swing back designed with the articulated gusset for full freedom of movement.

There is to be a separate 2" shirred waistband with heavy duty elastic. The entire waistband is to be shirred with the exception of an area 5 1/2" on either side of the front opening. There shall be side zipper entry on either side, approximately 11" in length and secured by a nylon zipper and snap closure. The shoulders shall have pads. A self goods reinforcement strip, approximately 3", shall be sewn on the side of the jacket joined at the top of the waistband and extending from side to side. There shall be a 1 1/2" wide fly from the bottom of the collar to the bottom of the waistband. There shall be a double fly of self goods covering the front zipper.

INSIDE DETAIL: On the left side of the coat, there shall be a gun pocket installed on the permanent lining of the coat to accept a small frame handgun. The gun pocket shall have a minimum opening of 4 1/2" and be a minimum of 6" deep. The gun pocket shall be furnished with a strap and snap closing. Bar tacks shall reinforce the opening. There shall be 2 cut-in pocket on the left and right sides measuring approximately 5 1/4" wide and 6" deep. There shall be a strap and snap on the lining of each sleeve end for attaching the zip-in liner.

SLEEVES: The sleeves shall be one piece set in with a single needle machine. The bottom of the sleeve shall have a heavy duty elastic closure with a triple snap adjustment.

POCKETS: There shall be two patch pockets with box pleats, finishing approximately 6 1/4" wide and 7 1/2" deep. Flaps shall be scalloped and self lined. They shall close with velcro on the side points and with a centered buttonhole. The pockets shall be self- lined with an opening of approximately 5 1/2" on the side. The left patch pocket is to have a pencil opening at the top of the flap. Both the pockets and the flaps are to be bartacked.

COLLAR: The stand-up collar shall be made using self material. It shall be interlined with Pellon.

BACK: The back band is constructed with heavy-duty elastic inserted between the folded fabric at the sides. The elastic is stretched and stitched with four threads. A 3 ¾” x 1.5” tab of two plies of shell material with #24 female snap (enameled cap) is provided to close the zipper vent when worn open. A brass oxidized male snap is provided on the elasticized back to fold the tab back when not in use.

EPAULETS: The epaulets shall be made of self goods. They shall be sewn into the sleeve head seam, "X" stitched, and tacked to the jacket at the neck.

BADGE TAB: The badge tab shall be made of the outer fabric, 1" wide with 2 metal eyelets spaced 3/4" vertically apart. It shall be centered 2 1/2" above the left pocket flap.

ZIPPER: There shall be a YKK #5, 2 way molded nylon zipper in the front and 11" nylon zipper on each side vent.

BUTTONS AND SNAPS: The pocket flaps and epaulets shall be secured with 24 ligne metal buttons. Flaps and epaulets shall close with 24 ligne metal buttons. Front fly and side zipper tabs shall be secured by high impact, non-reflective, non-glare, scratch resistant snaps.

THREAD: All sewing is to be done with polyester core thread or 100% spun polyester thread.

SIZE TAG AND CARE INSTRUCTIONS: Each jacket shall have a sewn-in woven size label. There shall also be a printed label with care instructions and each coat marked with Lot number, size, fiber content and WPL number.

SIZING: Jackets are to be sized in Regulars XS, S, M, L, XXL, and XXXL. In Longs M, L, XL and XXL.

EMBLEMS: There shall be a DEP Parks Emblem attached on each sleeve included in the cost of each jacket.

5.2.2: WINDBREAKER, NYLON, FLANNEL-LINED

FABRIC: High grade double strength water repellent 100% nylon permanent press.

COLOR: Spruce Green and Black

LINING: Flannel lining (100% polyester)

STYLE: Long point contemporary collar. Two lower front slant pockets with storm flap tops designed to keep out wind and rain. Full cut body and length. Matching color snap front drawstring bottom.

CUFFS: Wide comfortable elastic cuff.

SLEEVES: Double reinforced set-in sleeves.

EMBLEM: Florida Park Service Logo is to be embroidered on left breast of Spruce Green Jacket and Volunteer – Florida Park Service embroidered in white on left breast of Black Jacket.

5.3.1: SOCKS, MID-CALF (MEN )

FABRIC: 75% Hi-bulk Acrylic, 20% Nylon, 5% Lycra Spandex

COLOR: Black

STYLE: Mid-calf length. Duramax, or equivalent, construction, heel and toe.

CARE INSTRUCTIONS:Machine wash/dry warm. No bleach.

5.3.2: SOCKS, CREW LENGTH (WOMEN)

FABRIC: 75% Cotton, 25% Stretch Nylon

COLOR: Black

STYLE: Fashion crew length

CARE INSTRUCTIONS:Machine wash/dry warm. No bleach.

5.3.3: SOCKS, MEN/WOMEN, WHITE

FABRIC: 100% cotton or Department approved equivalent

STYLE: Crew length sock. Reinforced heel and toe.

CARE INSTRUCTIONS: Machine wash/dry

5.3.4: TIE, CLIP-ON

STYLE: New metal clip (Redi-Made) tie with pre-formed knot, center crease, permanently tied on metal frame, main body and hook of steel for added durability.

FABRIC: 100% fine line gabardine texturized woven polyester, 2 ply, approximately 10 ½ oz. per linear yard, 72 x 58 finished count construction, shrinkage allowance approximately 2% or equal.

COLOR: Spruce Green or Department approved equivalent. Color shall be rated 4.0 (high) on 40 hour light-fastness and on wash-fastness and against perspiration shade change.

5.3.5: TIE, FOUR-IN-HAND, WOVEN POLYESTER GABARDINE

STYLE: Regular style necktie, four-in-hand, pocket tip ends, long piecing, width at widest point to be approximately 3½”. Big end lining 24” long cut on bias, small end lining 24” long, cut on straight to eliminate excess stretching of neck band.

FABRIC: 100% fine line gabardine texturized woven polyester, 2 ply, approximately 10½ oz. per linear yard, 72 x 58 finished count construction, shrinkage allowance approximately 2% or equal.

COLOR: Spruce Green or Department approved equivalent.

5.3.6: TIE, WOMEN’S CROSSOVER

STYLE: Crossover style with adjustable band and matching covered button snap.

FABRIC: 100% fine line gabardine texturized woven polyester, 2 ply, approximately 10½ oz. per linear yard, 72 x 58 finished count construction, shrinkage allowance approximately 2% or equal.

COLOR: Spruce Green or Department approved equivalent.

5.3.7: BASEBALL STYLE CAP, WITH EMBROIDERED LOGO, SUMMER & WINTER

FABRIC: 100% Polyester 2 ply 11/25 oz. per linear yard. Gabardine weave. Gabardine weave and fabric is mandatory to maintain consistency with uniform. Visa finish. Spruce Green and Black.

MESH: (Summer Cap Only) Nylon, Endurlon or equal. Contour fit to conform to front fabric. Color to be Spruce Green and Black.

DESIGN: Baseball style five gore construction. Low crown seamless front, double supported with a sewn in Cotton Osnaburg and a polyester or nylon rigid half stay. The visor is to be of three piece construction with a minimum six rows of stitching. All gore seams to be taped to match fabric or black, the color of the mesh. The crown shall be of a matching color, or black, and an adjustable seven post plastic tab on the back to allow for full size range adjustment. One size fits all.

VISORBOARD: High density polypropeline extending approximately 3” from the sweatband (+/- ¼”). Thickness shall be .007 mm minimum.

SWEATBAND: Finished to 1¼” (+/- 1/16”). Construction of cotton or poly/cotton fabric lined inside with foam and nonwoven for rigidity and absorption.

SEAMING AND STITCHING: A proper seam allowance shall be maintained to prevent raw edges, run offs, twists, pleats, or open seams. All seams shall have 9-10 stitches per inch. Cutout at back shall be taped with color to match, or black.

LABEL: A permanent label shall be attached to the sweatband and state, ONE SIZED FITS ALL.

AGENCY LOGO: Florida Park Service Logo is to be embroidered on front of the Spruce Green Cap. Volunteer-Florida Park Service is to be embroidered in white on front of Black Cap.

5.3.8: EMBLEM, OFFICIAL

To be sewn on each sleeve of jackets and shirts one inch down from the shoulder seam. All threads are to be fast color, washable and all stitching on outer borders are to be lock-stitched to prevent raveling. The outer edges to be sewn with washable, colorfast, stitching, and on all outer borders are to be lock-stitched to prevent raveling. The outer edges to be sewn with six thread merrow stitches to eliminate raw edges. The emblem is to be approximately 4¾" wide by 3¾" high on fast color, washable white twill, one piece construction. Emblem to be a one quarter circle design with spruce green inter and outer borders. Lettering (bold): Top of circle: FLORIDA PARK SERVICE; left side: Environmental; right side: Protection. Letters ¼" in height to be centered in the space between the inner and outer borders and to be stitched with spruce green thread. The center space inside the inner border to be divided into a light blue top representing the sky and a dark blue representing water. Centered in the space is to be an outline of the State of Florida in sharp raised relief using rust color thread. The state outline to show Lake Okeechobee, Tampa Bay and the Florida Keys. The outline is to be overlaid on a stylized sun with sun in raised relief using gold color thread. Two sable palm trees with curved trunks of rust color thread and spruce green tops rise from the lower left inner border. In addition to the above patch for all uniformed positions, there will be a top tab approximately ⅝" wide attached (sewn not acceptable) in one piece with spruce green borders. Top tab lettering to be approximately ¼" in height of spruce green thread and the lettering. (See attached drawing for specific details.)

5.3.9: HAT, CAMPAIGN SYTLE

STYLE: Traditional four dent style. Color to be Tan. NO BADGE EYELET. Imported Milan Straw. Entire hat to be triple shellacked for extra waterproofing.

CROWN: Crown is to be 5” high. Each dent is to extend from 2” above bottom of crown to top of crown forming a flat portion at the top that is approximately 2” wide.

BRIM: 3” double brim, flat, no curl.

BAND: 12 Ligne Mylined Grograin, raw edge ⅞” wide, with side bow. Color to coordinate with hat color.

GROMMETS: Two (2) side black metal grommets 11/16” long opening in brim, one on each side, for hat strap.

STRAP: Black one piece leather ⅜” wide with non-tarnishable buckle.

SWEATBAND: Black nylon permanently laminated to polyurethane foam.

SIZES: 6½” through 7¾” in ⅛” increments.

PACKING: Individually boxed in corrugated containers minimum 125 lb. test.

UNIFORM SIZE CHART

Skirt (Standard Sizes):

4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24

Trousers, Dress Style and Work Style for Men (Waist Sizes):

28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 40, 42, 44, 46, 48, 50

Trousers, Dress Style and Work Style for Women (Standard Sizes):

4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24

Shorts, Men

(Waist Sizes): 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50

Shorts, Women

(Sizes): 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24

Shirt, Long Sleeve, Dress, Zipper Style and Work Style for Men:

14-14 1/2 15-15 1/2 16-16 1/2 17-17 1/2 18-18 1/2 19-19 1/2 20

32-33 X X X X X X X 34-35 X X X X X X X 36-37 X X X X X

Shirt, Short Sleeve, Dress, Zipper Style and Work Style for Men (Neck Sizes):

14-14 1/2, 15-15 1/2, 16-16 1/2, 17-17 1/2, 18-18 1/2, 19-19 1/2, 20

Shirt, Long and Short Sleeve, Dress, Zipper Style and Work Style for Women (Bust Sizes):

30, 32, 34, 36, 38, 40, 42, 44, 46, 48

Shirt Knit

XS, S, M, L, XL, XXL, XXXL. TO FIT BOTH MEN AND WOMEN.

Tee Shirt

S, M, L, XL, XXL

Jacket, All-Season: To fit both Men and Women

Size S M L XL XXL Reg. X X X X X Long X X X X

Windbreaker, Nylon Flannel-Lined: XS, S, M, L, XL, XXL

Socks, Men: Fit shoe sizes 6 - 12½ Socks, Women: Fit shoe sizes 4½ - 9

Socks, Men/Women: One size fits all Tie, Clip-on:

To be available in the following sizes:

Prep: 14½" Regular: 17" Long: 18½"

ALL UNIFORMS TO BE CUT ON STOCK PATTERN TO FIT ALL SIZES.

01a4ac6e7f1eb832df7b4553d7eba722.doc Page 36 of 36