Compak1eoc (2 Pieces Cnfe1eoc-M) Series Fast Ethernet Over Coax/Utp Transceivers

DIVISION 27 21 29 USA; Telephone: 203-796-5300; Fax 203-796- COMPAK1EOC (2 PIECES CNFE1EOC-M) 5303; Email: [email protected]; Internet: SERIES –FAST ETHERNET OVER COAX/UTP www.ComNet.net TRANSCEIVERS B. Substitutions: Not Permitted ENGINEERING SPECIFICATIONS C. All modules shall be supplied from a single manufacturer. PART 1 - GENERAL 2.02 MANUFACTURED UNITS 1.01 SUMMARY A. Model Number Descriptions: Reference Table A. Ethernet Transceivers A: Product Number Descriptions 1.02 SECTION INCLUDES B. Model Compatibility Chart: Reference Table B: A. COMPAK1EOC ( 2 pieces CNFE1EOC- Product Compatibility Chart M)Series Fast Ethernet Transceivers 2.03 GENERAL SPECIFICATIONS 1.03 REFERENCES A. The Fast Ethernet data transceiver system shall A. Underwriters Laboratory (UL) consist of a ComNet COMPAK1EOC (2 pieces B. Underwriters Laboratory Canada (ULC) CNFE1EOC-M) series device. The module shall C. European Union Compliance (CE) support the transmission of 10 or 100 Mbps 1.04 SYSTEM DESCRIPTION employing 75-ohm coaxial cable or Category 5, A. Performance Requirements: Provide an Ethernet 5e, or 6 unshielded twisted pair. The module transceiver system that transmits bi-directional shall support the Ethernet data interface and be 10 or 100 Mbps data over 75-ohm coaxial cable IEEE 802.3 compliant. The unit is set to auto- or Category 5, 5e, or 6 unshielded twisted pair negotiate data rates and can be used for half cable. duplex or full duplex transmission. The module 1.05 SUBMITTALS shall require no in-field adjustments or in-line A. Product Data: Manufacturer’s printed product attenuators to ease installation. The module shall data sheet for each type of Transceiver specified. provide power and link status indicating LED’s B. Detail Drawings: Electrical connect drawings. for monitoring proper system operation. The Product mounting template. modules shall provide automatic re-settable C. Manufacturer’s Installation and Operating solid-state current limiters and independent Manual: Printed installation and operating voltage regulators on each module to reduce the information for each type of Transceiver chance of a single point failure of the system. specified. The module shall have an MTBF of >100,000 D. Warranty: Manufacturer’s Printed Warranty hours and operate in an environment of 0.0˚ C to 1.06 DELIVERY, STORAGE AND HANDLING +60˚ C and relative humidity between 0% to A. Deliver materials in unopened factory packaging 95% (non-condensing). The module shall be UL with Manufacturer’s bar coding to the job site. and ULC listed and CE marked. The circuit B. Inspect product upon delivery to assure that board shall be UL 94 flame rated and meet all specified products have been received. PCI standards. All PC boards shall be C. Store in original packaging in a climate designated with part number, PC board number controlled environment. Storage Temperature and show appropriate revision number. Housing not to exceed: -40˚ C to +85˚ C shall be of all metal construction. All LED 1.07 PROJECT/SITE CONDITIONS indicators and both electrical and mechanical A. Temperature Requirements: Products shall connections shall be identified with silk-screened operate in an environment with an ambient labels. The module shall have a 5 year warranty temperature range of 0.0˚ C to +60˚ C without to reduce system life cycle cost in an event of a the assistance of fan-forced cooling. module failure. B. Humidity Requirements: Products shall operate 2.04 DATA SPECIFICATIONS in an environment with relative humidity of 0% A. Data Interface: Ethernet IEEE802.3 to 95% (non-condensing). If product is installed B. Data Rate: 10/100 Mbps in condensation conditions, unit shall have C. Operation Mode: Full or Half Duplex conformal coating applied to the printed circuit 2.05 STATUS INDICATORS board. A. Power: On/Green – Off/Off 1.08 WARRANTY 2.06 CONNECTORS A. Standard Communication Networks A. Coaxial: BNC Comprehensive 5 year Warranty: ComNet B. UTP: Screw Clamp Terminal Strip warrants the product to be free of factory defects C. Power: Screw Clamp Terminal Strip. under manufacture’s 5 year Warranty as D. Data: RJ-45 submitted under article 1.05 (E) 2.07 ELECTRICAL SPECIFICATIONS PART 2 - PRODUCTS A. Power: Surface Mount: 2.01 MANUFACTURER 12–27 VAC @ < 320 mA or A. Acceptable Manufacturer: Communication 12–27 VDC @ < 320 mA Networks 3 Corporate Drive Danbury, CT 06810 B. Current Protection: Automatic re-settable solid- C. Shipping box shall include the module, power state current limiters supply and operations manual. C. Voltage Regulation: Solid-state, Independent on 3.02 PREPARATION each board A. Standalone Module (Surface Mount) D. Circuit Board: UL 94 flame rated and meets all 1. Shall be mounted on a properly prepared IPC standards. surface adequate for the size and weight of 2.08 MECHANICAL SPECIFICATIONS module. The placement of the unit shall A. Surface Mount Dimensions: allow provision for cable installation and 4.1 × 3.7 × 1.1 in., (10.4 × 9.4 × 2.8 cm) maintenance as indicated on the approved B. Finish: Module shall be constructed of a metal detail drawings and in compliance with the enclosure with all connections and indicators ComNet mounting template and installation silk-screened directly on unit. manual. C. Weight: <2.0 lbs./0.9kg 3.03 INSTALLATION 2.9 ENVIRONMENTAL SPECIFICATIONS A. General: Locate modules as indicated on the A. MTBF: >100,000 Hours approved detail drawings and install module in B. Operating Temp: 0.0˚ C to +60˚ C compliance with the ComNet installation and C. Storage Temp: -40˚ C to +85˚ C operations manual. D. Relative Humidity: 0% to 95% (non- 3.04 TESTING condensing). If product is installed under A. Testing the Ethernet Link. condensation conditions, unit shall have 1. Verify that the data leads and signal leads conformal coating applied to the printed circuit are properly connected. board. (Add –C to model number for conformal 2. Make sure that power is applied to all coated printed circuit board) modules, controllers, and receiver drivers or 2.10 REGULATORY AGENCIES/APPROVALS other equipment used in the system. AND LISTINGS 3. Successful data link operation should be A. Underwriters Laboratory (UL) confirmed at this point by communicating B. Underwriters Laboratory Canada (ULC) with other equipment. C. UL 94-flame rated PCB board 3.05 CLEANING D. European Listed (CE) A. Follow all instructions for proper use of solvents PART 3 - EXECUTION and adhesives used for termination and splicing. 3.01 EXAMINATION B. At completion of the installation, dispose of all A. Inspect modules before installation. scraps properly. B. Modules shall be free of any cosmetic defects or damage. MANUFACTURED UNITS REFERENCE TABLES

Table A: Product Number Descriptions

COMPAK1EOC ( 2 DESCRIPTION PIECES CNFE1EOC-M) CNFE1EOC-M 10/100 Mbps Ethernet Transceiver, Mini

Table B: Product Compatibility Chart

TRANSCEIVER COMPATIBLE TRANSCEIVER CNFE1EOC-M CNFE1EOC-M

END OF SECTION