What print quality defect do you see if the main drive assembly is replaced incorrectly?

A. leading edge forward scatter B. partial or missing color plane C. retransfer D. electrostatic offset

Each HP Color LaserJet 4700 print cartridge is shipped with a toner dam. What is the purpose of the toner dam?

A. protects the photo sensitive drum B. collects excess toner during the first 100 jobs sent through the printing device C. keeps toner from leaking during shipping D. acts as a fusible link

What must you look for when reassembling the upper and lower cartridge guides of the main drive assembly to make sure they are reassembled correctly?

A. The upper guide has two projections and the lower guide has one projection. B. The upper guide latches from the bottom and the lower guide latches from the top. C. The upper guide holds the paper feed assembly and the lower guide holds the fuser drive assembly. D. The upper guide contains two screws and the lower guide contains four screws. You have replaced the formatter and transferred the compact flash firmware card from the old formatter to the newly installed formatter. Then, you power on the printing device.

What do you do after powering up the printing device to a "Ready" prompt?

A. Wait for all three lights below the control panel to flash 5 times.

B. Wait five minutes before using the printing device so the printer configuration information can be restored from the compact flash memory to the NVRAM. C. Immediately power cycle the printing device again to make sure the printer configuration was restored from the compact flash memory to the NVRAM. D. Immediately print Diagnostics Page, check the media sensor calibration values and re-enter through the control panel Service menu, if necessary.

What effect does smart duplexing have on HP Color LaserJet 4700 performance?

A. limits toner used during duplex jobs B. accepts data from media sensor to detect whether or not the media can be duplexed C. does not duplex the last page of jobs containing an odd number of images (sides) D. decreases print speed, but also reduces engine cycle count from unnecessarily incrementing if simplexing final page What must you do before performing an engine test on the HP Color LaserJet 4700ph+?

A. Tray 1 must be loaded with paper. B. The duplexer must be removed. C. The output device connection cable must be detached from the printing device. D. The stapler/stacker accessory must be removed.

When should the paper feed assembly be disassembled and repaired?

A. for repeated paper jams caused by excessive (out of spec) paper skew B. if replacing feed rollers and adjusting paper skew sensors do not solve repeated jam errors C. paper feed assembly should only be replaced as a full unit, never be disassembled for repair D. to replace the media sensor

Automatic calibration occurs for which events? Select THREE.

A. whenever the device comes out of power save mode B. when the printer is powered on after having been powered down for longer than 20 seconds C. whenever a brand new print cartridge is installed in the printer D. when 1,000 pages have printed since the last calibration According to the Service Manual, after the main drive assembly gears are aligned, how should the cartridge interlock rod be positioned?

A. up B. down C. center D. positioning does not matter

The fusing pressure release mechanism activates when ______.

A. each print job is complete B. the top cover is opened C. a paper jam occurs D. the printing device is powered off by unplugging the AC from the wall outlet

How many different formatters do the HP Color LaserJet 4700 Printer Series have?

A. two different formatters: one for the Color LaserJet 4700 and one for all other bundles: N, DN, DTN, and PH+ B. three different formatters: one for the Color LaserJet 4700, one for the Color LaserJet 4700n, and one for all other bundles: DN, DTN, and PH+ C. three different formatters: one for the Color LaserJet 4700, one for the Color LaserJet 4700ph+, and one for all other bundles: N, DN, and DTN D. four different formatters: one for the Color LaserJet 4700, one for the Color LaserJet 4700n, one for the Color LaserJet 4700ph+, and one for the duplex-enabled bundles: DN and DTN

What action must be taken before a newly installed paper feed assembly will work?

A. The media sensor sticker must be removed from the newly installed paper feed assembly. B. Input the media sensor value of the newly installed paper feed assembly using the control panel Service menu. C. Transfer the media sensor value from the old paper feed assembly and to the newly installed paper feed assembly using the control panel Service menu. D. Input the serial number of the newly installed paper feed assembly using the control panel Service menu.

By illuminating the front and back sides of media feeding through the paper path, the automatic media type sensor detects media ______.

A. weight and density B. weight and dimensions C. weight and color D. weight and gloss level

What color screws must you use to fix the drum drive assembly to the main drive during reinstallation?

A. grey B. silver C. black D. bluish-purple

What is the purpose of the HP Color LaserJet 4700 downloadable color tables?

A. match CMYK+ variables in color output B. assist installed color print cartridges in the laying of toner for color output jobs C. emulate color printing of other HP Color LaserJet devices D. define halftone options for Smooth and Detail, which affects the resolution of color output

When installing drum drive motors from service parts ______.

A. the motors are optimized for any color and can be used with any color B. each color (C, M, Y, K) has its own drum drive motor part number, optimized for that color C. all motors must be replaced as a set D. the fusible link burns up and resets the drum driver counters

For what reason should you disassemble and then replace the paper feed assembly?

A. if repeated paper jams occur due to excessive paper skew B. if replacing feed rollers and adjusting paper skew sensors do not solve repeated jam errors C. if the media sensor value no longer matches the value on the label located on the paper feed assembly D. the paper feed assembly can be replaced as a full unit but should never be disassembled

The HP Color LaserJet 4700 automatically calibrates and cleans at certain times to maintain optimum print quality. Which of the following conditions cause the device to perform a color-plane registration (CPR)? Select THREE.

A. one or more print cartridges are installed that have not previously been installed in the printing device B. 10,000 pages have printed since the last calibration C. 'Full Calibrate Now' is requested through the control panel D. the ETB is replaced What do you do before removing or replacing the duplexer?

A. put the printing device into Service Mode through the control panel B. power off and unplug the printing device C. power cycle the printing device D. remove all covers and ground the device

What needs to be done before a newly installed paper feed assembly will work?

A. Remove the media sensor value sticker from the new paper feed assembly.

B. Remove the media sensor value sticker from the old paper feed assembly and apply it to the newly installed paper feed assembly. C. Use the printing device control panel Service menu to input the serial number of the new paper feed assembly. D. Use the printing device control panel Service menu to input the media sensor value from the sticker on the new paper feed assembly.

The HP Color LaserJet 4700 Paper Handling Configuration page ______.

A. indicates the installed output device maintenance code B. indicates the installed output device product life expectancy C. indicates the firmware datecode for the installed output device D. indicates paper capacities for input and output trays

What do you do after installing the replacement formatter and DC controller?

A. perform a “Quick Calibrate Now” B. perform a “Full Calibrate Now” C. perform a “Quick Calibrate Now” three (3) times D. perform a “Full Calibrate Now” three (3) times

Before performing an engine test on the HP Color LaserJet 4700ph+, ______.

A. the printing device must be powered off B. the printing device must be power-cycled C. the output device connection cable must be detached from the printing device D. the output device and output accessory bridge must be removed

What does the HP Color LaserJet 4700 Override Out setting do?

A. allows the printing device to continue printing after “end of life” until print quality becomes compromised B. detects the remaining life of the Optical Photo Conductive (OPC) drum before preventive maintenance is required C. instructs the printing device to conserve toner when the device detects that toner is low in one of the print cartridges D. allows the printing device to continue printing when a color supply is out, but displays a warning that supply is out and must be replaced Which is the correct first troubleshooting action to take to solve a partial missing color plane print defect?

A. correct the image transfer kit timing application B. correct the timing of the intermediate transfer belt (ITB) alienation system C. reinstall the main drive assembly D. correct the timing of the developer alienation system

The HP Color LaserJet 4700 printer series uses the SCIP packaging approach. What does SCIP stand for?

A. Ship Cartridges Inside Printer B. Standard Copier Internal Packaging C. Secure Color Internal Parcel D. Setup Cartridge for Initial Placement

You are replacing the main drive assembly. What alignments of the gears are required to avoid print quality problems? Select THREE.

A. The front and back gears of the cartridge lower and upper guide units. B. The developing clutch gears must be aligned with the arrow on the metal sheet. C. The developing clutch gears must be aligned with the developing alienation gears. D. The four positioning marks on the developing alienation gears with the corresponding marks on the metal sheet

What effect does smart duplexing have on HP Color LaserJet 4700 performance?

A. limits toner used during duplex jobs B. increases print speed and reduces paper count C. inserts a blank page at the end of odd-numbered duplex jobs so the final page of the job faces up D. decreases print speed, but reduces paper count