Coiling Doors and Shutters

SECTION 08330 COILING DOORS AND SHUTTERS

Display hidden notes to specifier. (Don't know how? Click Here)

PART 1 GENERAL

1.1 SECTION INCLUDES

1.A. Overhead coiling doors.

1.B. Overhead coiling fire doors.

1.C. Coiling counter shutters.

1.D. Coiling counter fire shutters.

1.2 RELATED SECTIONS

2.A. Section 05100 - Structural Metal Framing.

2.B. Section 06100 - Rough Carpentry.

2.C. Section 09900 - Paints and Coatings.

2.D. Section 16050 - Basic Electrical Materials and Methods.

1.3 REFERENCES

3.A. ASTM International (ASTM): 3.A.1. ASTM A480/A480M - Standard Specification for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip. 3.A.2. ASTM A653/A653M - Standard Specification for Specification for Steel Sheet, Zinc- Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process. 3.A.3. ASTM A666 - Standard Specification for Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. 3.A.4. ASTM B209 - Standard Specification for Aluminum - Alloy Sheet and Plate. 3.A.5. 08330-1 ASTM B221 - Standard Specification for Aluminum - Alloy Extruded Bars, Rods, Wires, Shapes and Tubes.

3.B. National Fire Protection Association NFPA 80 - Standard for Fire Doors and Fire Windows.

3.C. Underwriters Laboratories (UL) 10B - Standard for Fire Tests of Door Assemblies.

1.4 SUBMITTALS

4.A. Submit under provisions of Section 01300.

4.B. Shop Drawings: Indicate opening dimensions and required tolerances, jamb connection details, anchorage spacing, hardware locations, installation details, and special conditions.

4.C. Product Data: Provide information on components, application, hardware and accessories.

4.D. Samples for Initial Selection: Provide manufacturer's finish charts showing full range of colors and textures available for units with factory applied finishes: 4.D.1. Include similar samples of accessories involving color selection.

4.E. Samples for Verification: Provide for each type of exposed finish on the following components in manufacturer's standard sizes: 4.E.1. Curtain slats. 4.E.2. Bottom bar.

4.F. Sustainable Design Submittals: 4.F.1. Recycled products: Indicate percentage of recycled material used in the manufacturing of products and percentage classified as post-consumer. 4.F.2. Regional products: Indicate location of product manufacturer and distance from manufacturing facility to project site.

4.G. Closeout Submittals: Operation and maintenance data.

1.5 QUALITY ASSURANCE

5.A. Company specializing in the manufacturing of products specified in this section and with a minimum of five years experience.

5.B. Installer Qualifications: Installer shall be authorized and qualified to install overhead door systems on the type and scope of project specified.

5.C. Source Limitations: Provide overhead coiling doors from one manufacturer for each type of door. Provide operators and other accessories from source acceptable to overhead coiling door manufacturer

08330-2 5.D. Performance Requirements: 5.D.1. Fire Door Construction: Conform to UL 10B. 5.D.2. Installed Fire Door Assembly: Conform to NFPA 80.

1.6 DELIVERY, STORAGE, AND HANDLING

6.A. Store products in manufacturer's unopened packaging until ready for installation.

6.B. Store and dispose of all materials in accordance with federal, state and local laws.

1.7 PROJECT CONDITIONS

7.A. Maintain environmental conditions (temperature, humidity and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

8.A. Provide an original of the manufacturer's limited warranty against manufacturing defects and product workmanship. 8.A.1. Duration: One year. 8.A.2. Duration: Five years.

PART 2 PRODUCTS

2.1 MANUFACTURERS

1.A. Acceptable Manufacturer: C.H.I. Overhead Doors, which is located at: 1485 Sunrise Dr.; Arthur, IL 61911; Toll Free Tel: 800-590-0559; Fax: 217-543-4454; Email: request info ([email protected]); Web: www.chiohd.com

1.B. Substitutions: Not permitted.

1.C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 MATERIALS

2.A. Galvanized Steel Sheet: 2.A.1. Galvanized commercial steel, (CS type) per ASTM A653/A653M, G90 and G60 coating class.

2.B. Stainless Steel Sheet: ASTM A480/A480M or ASTM A666; Type 304 or 316, roll form temper.

08330-3 2.C. Aluminum: 2.C.1. Extrusions: ASTM B221, alloy and temper best suited to application. 2.C.2. Sheet: ASTM B209, alloy and temper best suited to application.

2.3 OVERHEAD COILING DOORS

3.A. Performance: 3.A.1. Wind Loads: Design door assembly to withstand a minimum of 20 psf in accordance with ASTM E330 using a 1.0 factor of safety. 3.A.2. Wind Loads: Design door assembly to withstand wind load pressures of ____ psf positive and ____ psf negative in accordance with ANSI/ DASMA 108. 3.A.3. Windborne-Debris Impact Resistance: Design door assembly to pass missile impact and cyclic pressure tests in accordance with ANSI/ DASMA 108 and/or ANSI/DASMA 115 and to withstand wind load pressures indicated. 3.A.4. Seismic Performance: Overhead coiling doors shall be evaluated for seismic performance to withstand the effect of earthquake motions determined according to ASCE/SEI 7. 3.A.5. Operation: Design complete door assembly including operator for use of not less than 20,000 cycles. 3.A.6. Operation: Design complete door assembly including operator for use of not less than 50,000 cycles. 3.A.7. Operation: Design complete door assembly including operator for use of not less than 100,000 cycles.

3.B. Construction: 3.B.1. Material: Galvanized steel. 3.B.1.a. Gauge: Per design requirements. 3.B.1.b. 18 gauge. 3.B.1.c. 20 gauge. 3.B.1.d. 22 gauge. 3.B.1.e. 24 gauge. 3.B.1.f. Finish: Polyester finish, Gray. 3.B.1.g. Finish: Polyester finish, White. 3.B.1.h. Finish: Powder coat, Color: ____. 3.B.1.i. Finish: Powder coat, Custom color. 3.B.2. Material: Stainless Steel 3.B.2.a. 22 gauge. 08330-4 3.B.3. Material: Aluminum 3.B.3.a. 16 gauge./.050 inch. 3.B.4. LEED Requirements: 3.B.4.a. Recycled content: Minimum [ ] percent with minimum [ ] percent classified as post- consumer. 3.B.5. Profile: Flat, non-insulated. 3.B.6. Profile: Flat, perforated, dholes on 3/32 inch staggered centers for 40 percent free air. 3.B.7. Profile: Curved, non-insulated. 3.B.8. Profile: Flat, insulated, with expanded polystyrene insulation and 24 gauge steel backer. 3.B.9. Profile: Flat, insulated, with urethane insulation and 24 gauge steel backer. 3.B.10. Bottom bar: Two steel angles bolted back-to-back, with adjustable tubular compression weather seal. 3.B.10.a. Finish: Painted black. 3.B.10.b. Finish: Hot dip galvanized. 3.B.10.c. Finish: Cold galvanizing. 3.B.10.d. Finish: Powder coated. 3.B.11. Bottom bar: Extruded aluminum tube. 3.B.11.a. Finish: Clear anodized. 3.B.11.b. Finish: Powder coated. 3.B.12. Guides: Structural angles bolted together to form guide and mounting surface. 3.B.12.a. Material: Steel, Painted black. 3.B.12.b. Material: Steel, Hot dip galvanized. 3.B.12.c. Material: Steel, Cold galvanizing. 3.B.12.d. Material: Steel, Powder coated. 3.B.12.e. Material: Stainless steel. 3.B.12.f. Material: Aluminum, mill finish. 3.B.13. Guides: Rolled steel type shaped to form guide channel and mounting surface. 3.B.14. End locks: Galvanized malleable iron, attached to every other slat to act as wearing surface and prevent lateral movement. 3.B.15. Wind locks: Per design and wind load requirements 3.B.16. Head Plate: Rectangular steel plate, with precision sealed ball bearings supporting drive side axle. 3.B.17. Barrel Assembly: Steel pipe, sized for maximum deflection, with threaded rings or lugs 08330-5 welded to barrel assembly for curtain attachment. 3.B.18. Springs: Counterbalanced torsion springs, grease packed and mounted on steel torsion shafts. 3.B.18.a. Designed for minimum 20,000 cycles. 3.B.18.b. Designed for minimum 50,000 cycles. 3.B.18.c. Designed for minimum 100,000 cycles. 3.B.19. Vision Lites: Rectangular, 5 inches wide by 1-1/8 inches high, clear acrylic panels set with silicone sealant and rivets. 3.B.20. Ventilated Slats: Rectangular punched openings in slats on 7 inch centers, 5 inches wide by 1-1/8 inches high. 3.B.20.a. Pattern: Three wide by three high. 3.B.20.b. Pattern: Five wide by five high. 3.B.20.c. Pattern: __ wide by __ high. 3.B.20.d. Alignment: Centered. 3.B.20.e. Alignment: Left side looking out. 3.B.20.f. Alignment: Right side looking out. 3.B.21. Hood: Shaped to fit within the head plates and with intermediate supports as required: 3.B.21.a. Material: Galvanized steel, match curtain finish. 3.B.21.b. Material: Galvanized steel, polyester finish, Gray. 3.B.21.c. Material: Galvanized steel, polyester finish, White. 3.B.21.d. Material: Galvanized steel, polyester finish, Tan. 3.B.21.e. Material: Galvanized steel, polyester finish, Brown. 3.B.21.f. Material: Galvanized steel, Powder coated. 3.B.21.g. Material: Stainless steel, #4 finish. 3.B.21.h. Material: Aluminum, anodized finish. 3.B.22. Weather Seal: 3.B.22.a. Tubular vinyl bottom seal. 3.B.22.b. Vinyl guide seal with rubber hood baffle. 3.B.22.c. Guide brush seal. 3.B.22.d. Header brush seal.

3.C. Locking Mechanism: Plated steel slide bolt locks with padlock provisions. 3.C.1. Two plated steel slide bolt locks with padlock provisions. 3.C.2. 08330-6 Chain keeper suitable for padlocking. 3.C.3. Cylinder lock mounted to double angle bottom bar. 3.C.3.a. Keyed on exterior of door with thumb turn on interior. 3.C.3.b. Keyed on both sides of the door. 3.C.4. Extruded aluminum tube type bottom bar with throw handle and cylinder locking. 3.C.4.a. Keyed on exterior of door with thumb turn on interior. 3.C.4.b. Keyed on both sides of the door. 3.C.5. Interlock Switches: Equip power-operated doors with safety interlock switch to disengage power supply when door is locked. 3.C.6. Mounting: Face of wall and above lintel. 3.C.7. Mounting: Face of wall and under lintel. 3.C.8. Mounting: Between jamb and above lintel. 3.C.9. Mounting: Between jamb and under lintel.

3.D. Manual Operation: 3.D.1. Manual push up. 3.D.2. Chain hoist.

3.E. Electric Operator: Provide operator unit, UL listed and UL labeled, size as recommended by manufacturer, capable of driving door at a speed of no less than 8 inches per second nor more than 12 inches per second. 3.E.1. Usage Classification: Heavy duty; 25 or more cycles per hour and over 90 cycles per day. 3.E.2. Usage Classification: Standard duty; up to 25 cycles per hour and up to 90 cycles per day. 3.E.3. Usage Classification: Medium duty; up to 12 cycles per hour and up to 50 cycles per day. 3.E.4. Usage Classification: Light duty; up to 10 cycles per hour. 3.E.5. Operator Location: Mounted on front of hood. 3.E.6. Operator Location: Wall mounted. 3.E.7. Operator Location: Mounted on opposite side of the wall with connection through wall. 3.E.8. Operator Location: As shown on Drawings. 3.E.9. Operator Exposure: Interior. 3.E.10. Operator Exposure: Exterior or wet and humid area: Provide operator cover to protect operator from weather. 3.E.10.a. Finish: To match hood. 3.E.10.b. 08330-7 Finish: Galvanized. 3.E.11. Power supply: 115 Volts AC, single phase. 3.E.12. Power Supply: 230 Volts AC, single phase. 3.E.13. Power Supply: 208/230 Volts AC, three phase. 3.E.14. Power Supply: 460 Volts AC, three phase. 3.E.15. Power Supply: 575 Volts AC, three phase. 3.E.16. Manually operable in case of power failure. 3.E.17. Control Station: 24 V three button control station with open, close, and stop buttons. 3.E.18. Control Station: 24 V three button control station with open, close, and stop buttons and keyed lockout. 3.E.19. Control Station: 24 V key control station with open and close contacts. 3.E.20. 24 V key control station with open/close contacts and stop button. 3.E.21. Control Station Mounting: NEMA 1 Surface mounted for interior. 3.E.22. Control Station Mounting: NEMA 1 Flush mounted for interior. 3.E.23. Control Station Mounting: NEMA 4 Surface mounted for exterior. 3.E.24. Control Station Mounting: NEMA 4 Flush mounted for exterior. 3.E.25. Remote Controls: Provide radio receiver and single button remote controls. 3.E.25.a. Provide ___ transmitters. 3.E.26. Remote Controls: Provide radio receiver and three button remote controls. 3.E.26.a. Provide ___ transmitters. 3.E.26.b. Program remote controls to Open/ Close/ Stop the door. 3.E.27. Special Controls: 3.E.27.a. Keypad Entry System: Mounting post. 3.E.27.b. Card Reader System: Mounting post. 3.E.27.c. Internet Connectivity. 3.E.27.d. Door Timer. 3.E.27.e. Loop Detector. 3.E.27.f. Pull Cord. 3.E.27.g. Vehicle Detector.

3.F. Primary Entrapment Protection Devices: 3.F.1. NEMA 1 Monitored Photo Sensors: Photo eyes fully monitored, non-contact, infrared beam photo sensor system shall reverse a closing door to the full open position when an 08330-8 obstruction is sensed; photo sensors shall be mounted no higher than 6 inches (152 mm) maximum above the floor. 3.F.2. NEMA 4 Monitored Photo Sensors: Photo eyes fully monitored, non-contact, photo beam reversing photo sensor system with NEMA 4 watertight enclosure shall reverse a closing door to the full open position when an obstruction is sensed; photo sensors shall be mounted no higher than 6 inches (152 mm) maximum above the floor. 3.F.3. Monitored Electric Sensing Edge: Electric sensing edge fully monitored and connected to the operator shall reverse a closing door to the full open position when an obstruction is sensed.

3.G. Ancillary Entrapment Protection Devices: 3.G.1. Non-Monitored Electric Sensing Edge: Non-monitored electric sensing edge shall reverse a closing door to the full open position when an obstruction is sensed. 3.G.2. Pneumatic Sensing Edge: Pneumatic sensing edge shall reverse a closing door to the full open position when an obstruction is sensed.

3.H. Finish: 3.H.1. Primer and finish coat. Color to be selected from manufacturer's standard colors. 3.H.2. Powder Coat. Color to be selected from manufacturer's standard colors. 3.H.3. Finish: No. 4 satin. 3.H.4. Finish: Clear anodized.

2.4 OVERHEAD COILING FIRE DOORS

4.A. Construction: 4.A.1. Material: Galvanized steel. 4.A.1.a. Gauge: Per design requirements. 4.A.1.b. Gauge: 18 gauge. 4.A.1.c. Gauge: 20 gauge. 4.A.1.d. Gauge: 22 gauge. 4.A.2. Profile: Flat, non-insulated, 4.A.3. Profile: Curved, non-insulated. 4.A.4. Profile: Flat, insulated with mineral wool insulation with 24 gauge backer. 4.A.5. Bottom bar: Two galvanized steel angles bolted back-to-back. 4.A.6. Guides: Three steel angles bolted together to form guide and mounting surface. 4.A.7. End locks: Galvanized malleable iron, attached to every other slat to act as wearing surface and prevent lateral movement. 4.A.8. Wind locks: Per design and wind load requirements. 08330-9 4.A.9. Head Plate: Rectangular steel plate, with precision sealed ball bearings supporting drive side axle. 4.A.10. Barrel Assembly: Steel pipe, sized for maximum deflection, with threaded rings or lugs welded to barrel assembly for curtain attachment. 4.A.11. Springs: Counterbalanced torsion springs, grease packed and mounted on steel torsion shafts, designed for minimum 20,000 cycles.

4.B. Locking Mechanism: Plated steel slide bolt locks with padlock provisions. 4.B.1. Interlock Switches. 4.B.2. Interior mounted cylinder with throw handle. 4.B.3. Exterior mounted cylinder with throw handle. 4.B.4. Access from Coil Side. 4.B.5. Access from Fascia Side. 4.B.6. Access from Both Sides.

4.C. Electric Operator: 4.C.1. Type: Externally mounted on drive side of coil. 4.C.2. Power supply: 115 Volts AC. 4.C.3. Power Supply: 208/230 Volts AC. 4.C.4. Power Supply: 460 Volts AC. 4.C.5. Control Station: 24 Volt Keyed Switch. 4.C.6. Control Station: 24 Volt two button (Open / Close) station. 4.C.7. Control Station: 24 Volt three button (Open / Stop / Close) station.

4.D. Safety Reversing Edge Detection Device: 4.D.1. Photoelectric Sensor: Detect obstruction and reverse door without requiring door to contact obstruction. 4.D.2. Electric Edge, Two Wire: Detect obstruction and reverse door upon contact with electric strips in vinyl housing. 4.D.3. Electric Edge, four wire, fail-safe, self monitoring: Detect obstruction and reverse door upon contact with electric strips in vinyl housing. 4.D.4. Pneumatic Reversing Edge. Pressure sensitive air switch attached to gum rubber hose located in bottom astragal of door section.

4.E. Detection/ Release/ Warning Device: 4.E.1. Three replaceable 165 degree Fahrenheit fusible links, (Standard) interconnected and mounted on both sides of door opening. 08330-10 4.E.2. Smoke detectors: manufacturer's standard UL-labeled smoke detector and door-holder- release devices. 4.E.3. Heat rise detectors: manufacturer's standard UL-labeled heat rise detector and door- holder-release devices 4.E.4. Connection to building fire alarm and detection system. 4.E.5. Fail-Safe release device. 4.E.6. Fail-Safe release device with 72 hour battery backup. 4.E.7. Audible warning system and strobe light.

4.F. Curtain Accessories: 4.F.1. Smoke Seals: Equip each fire-rated door with replaceable smoke-seal perimeter gaskets or brushes for smoke and draft control as required for door listing and labeling by a qualified testing agency. 4.F.2. Smoke Control Label: Furnish doors with a UL "S" label in addition to the fire door label to certify smoke control listing.

4.G. Finish: 4.G.1. Primer and Finish Coat: Color to be selected from manufacturer's standard colors. 4.G.2. Powder Coat: Color to be selected from manufacturer's standard colors.

2.5 COILING COUNTER SHUTTERS

5.A. Construction: 5.A.1. Flat 22 gauge galvanized steel with an extruded aluminum bottom bar and a 24 gauge rectangular steel hood. 5.A.2. Flat 22 gauge stainless steel with a single angle bottom bar and a 24 gauge rectangular stainless steel hood. 5.A.3. Flat 0.050 inch thick extruded aluminum 1-1/2 inches x 1/2 inch deep with an extruded aluminum bottom bar and a 24 gauge rectangular aluminum hood. 5.A.4. End Locks: Nylon, attached to every other slat providing a wearing surface and preventing movement. 5.A.5. Guides: Bolted together to form guide channel and mounting surface. With soft brush guides running to full height preventing metal-to-metal contact. 5.A.5.a. Two-piece box-shaped extruded aluminum with soft brush guide runners full height preventing metal-to-metal contact. 5.A.5.b. Two-piece formed stainless steel. 5.A.6. Head Plate: Rectangular steel plate, with precision sealed ball bearings supporting drive side axle. 5.A.7. Barrel Assembly: Steel pipe, sized for maximum deflection, with threaded rings or lugs 08330-11 welded to barrel assembly for curtain attachment. 5.A.8. Springs: Counterbalanced torsion springs, grease packed and mounted on steel torsion shafts, designed for 20 cycles per day.

5.B. Locking Mechanism: Throw handle with provisions for keyed cylinder locking and master keying. 5.B.1. Interlock Switches. 5.B.2. Interior Mounted. 5.B.3. Exterior Mounted. 5.B.4. Mounted each side. 5.B.5. Keyed access from Coil Side. 5.B.6. Keyed access from Fascia Side. 5.B.7. Keyed access from Both Sides. 5.B.8. Master key all cylinders.

5.C. Electric Operator: 5.C.1. Type: Internally mounted in barrel. 5.C.2. Type: Externally mounted on drive side of shutter. 5.C.3. Power supply: 115 Volts AC. 5.C.4. Power Supply: 208/230 Volts AC. 5.C.5. Power Supply: 460 Volts AC. 5.C.6. Manually operable in case of power failure. 5.C.7. Control Station: 24 Volt Keyed Switch. 5.C.8. Control Station: 24 Volt two button (Open / Close) station. 5.C.9. Control Station: 24 Volt three button (Open / Close/Stop) station.

5.D. Finish: 5.D.1. Primer and finish coat. Color to be selected from manufacturer's standard colors. 5.D.2. Powder Coat. Color to be selected from manufacturer's standard colors. 5.D.3. Finish: No. 4 satin. 5.D.4. Finish: AAMA 611, Class I Clear anodized.

2.6 COILING COUNTER FIRE SHUTTERS

6.A. Construction:

08330-12 6.A.1. 22 gauge galvanized steel with a single angle bottom bar and a 24 gauge rectangular galvanized steel hood. 6.A.2. 22 gauge stainless steel with a single angle bottom bar and a 24 gauge rectangular stainless steel hood. 6.A.3. Guides: Bolted together to form guide channel and mounting surface. 6.A.4. End Locks: Galvanized malleable iron, attached to every other slat providing a wearing surface and preventing movement. 6.A.5. Head Plate: Rectangular steel plate, with precision sealed ball bearings supporting drive side axle. 6.A.6. Barrel Assembly: Steel pipe, sized for maximum deflection, with threaded rings or lugs welded to barrel assembly for curtain attachment. 6.A.7. Springs: Counterbalanced torsion springs, grease packed and mounted on steel torsion shafts, designed for minimum 20,000 cycles.

6.B. Locking Mechanism: Plated steel slide bolt locks with padlock provisions. 6.B.1. Interlock Switches. 6.B.2. Access from Coil Side. 6.B.3. Access from Fascia Side. 6.B.4. Access from Both Sides. 6.B.5. Smoke Control Label: Furnish doors with a UL "S" label in addition to the fire door label to certify smoke control listing.

6.C. Electric Operator: 6.C.1. Type: Externally mounted on drive side of shutter. 6.C.2. Power supply: 115 Volts AC. 6.C.3. Power Supply: 208/230 Volts AC. 6.C.4. Power Supply: 460 Volts AC. 6.C.5. Control Station: 24 Volt Keyed Switch. 6.C.6. Control Station: 24 Volt two button (Open / Close) station. 6.C.7. Control Station: 24 Volt three button (Open / Close/Stop) station.

6.D. Detection/ Release/ Warning Device: 6.D.1. Three replaceable 165 degree Fahrenheit fusible links, (Standard) interconnected and mounted on both sides of door opening. 6.D.2. Smoke detectors: manufacturer's standard UL-labeled smoke detector and door-holder- release devices. 6.D.3. Heat rise detectors: manufacturer's standard UL-labeled heat rise detector and door- 08330-13 holder-release devices 6.D.4. Connection to building fire alarm and detection system. 6.D.5. Fail-Safe release device. 6.D.6. Fail-Safe release device with 72 hour battery backup. 6.D.7. Audible warning system and strobe light.

6.E. Curtain Accessories: 6.E.1. Smoke Seals: Equip each fire-rated door with replaceable smoke-seal perimeter gaskets or brushes for smoke and draft control as required for door listing and labeling by a qualified testing agency. 6.E.2. Smoke Control Label: Furnish doors with a UL "S" label in addition to the fire door label to certify smoke control listing.

6.F. Finish: 6.F.1. Primer and Finish Coat. Color to be chosen from manufacturer's standard selections. 6.F.2. Powder Coat. Color to be chosen from manufacturer's standard selections. 6.F.3. Finish: No. 4 satin.

PART 3 EXECUTION

3.1 EXAMINATION

1.A. Examine substrates, areas, and conditions for compliance with requirements for substrate construction and other conditions affecting performance of the work.

1.B. Examine locations of electrical connections.

1.C. Proceed with installation only after all unsatisfactory conditions have been corrected.

3.2 INSTALLATION

2.A. Install door and shutter assembly in accordance with manufacturer's instructions.

2.B. Anchor to adjacent construction without distortion or stress.

2.C. Fit and align door and shutter assembly including hardware, plumb, level and square to ensure smooth operation.

2.D. Make wiring connections between power supply and operator and between operator and controls.

3.3

08330-14 ADJUSTING

3.A. Adjust hardware and moving parts so that doors operate smoothly throughout full operating range.

3.B. Adjust seals to provide a tight fit around the entire perimeter.

3.4 DEMONSTRATION

4.A. Demonstrate proper operation to Owner.

4.B. Perform fire door and shutter drop tests in presence of Owner or owner's representative. Require signature for manufacturer supplied drop test form.

END OF SECTION

08330-15