Model ATH33G50 Antenna, Standard Gain 33Ghz–50Ghz

Total Page：16

File Type：pdf, Size：1020Kb

Model ATH33G50 Antenna, Standard Gain 33GHz–50GHz The Model ATH33G50 is a wide band, high gain, high power microwave horn antenna. With a minimum gain of 20dB over isotropic, the Model ATH33G50 supplies the high intensity fields necessary for RFI/EMI field testing within and beyond the confines of a shielded room. The Model ATH33G50 is extremely compact and light weight for ready mobility, yet is built tough enough for the extra demands of outdoor use and easily mounts on a rigid waveguide by the waveguide flange. Part of a family of microwave frequency antennas, the Model ATH33G50 provides the 33-50GHz response required for many often used test specifications. The Model ATH33G50 standard gain pyramidal horn antenna is electroformed to give precise dimensions and reproducible electrical characteristics. The Model ATH33G50 is used to measure gain for other antennas by comparing the signal level of a test antenna to the signal level of a test antenna to the standard gain horn and adding the difference to the calibrated gain of the standard gain horn at the test frequency. The Model ATH33G50 is also used as a reference source in dual-channel antenna test receivers and can be used as a pickup horn for radiation monitoring. SPECIFICATIONS FREQUENCY RANGE .................................................... 33-50GHz POWER INPUT (maximum) ............................................ 240 watts CW 2000 watts Peak POWER GAIN (over isotropic) ........................................ 20 ± 2dB VSWR Average ................................................................. 1.2:1 CONNECTOR .............................................................. WR 22 waveguide MOUNTING PROVISIONS ............................................. Waveguide flange SIZE (WxHxD) ................................................................ 4 x 3 x 9 cm (1.57 x 1.18 x 3.54 in) WEIGHT ....................................................................... 0.15 kg (0.33 lbs) 061909 160 School House Road Souderton, PA 18964-9990 • 215-723-8181 • www.ar-worldwide.com Page 1 of 2 ATH33G50 Field Strength at 1 meter 1000 10,000 100 Watts 50 Watts 2000 Watts Peak 20 Watts 1000 Watts Peak 10 Watts Field Level (V/m) 500 Watts Peak 5 Watts 200 Watts 2 Watts 100 1,000 30 35 40 45 50 55 Frequency (GHz) ATH33G50 Field Strength at 3 meters 1000 10000 100 Watts 50 Watts 2000 Watts Peak 20 Watts 100 1000 Watts Peak 1000 10 Watts 5 Watts 500 Watts Peak Field Strength (V/m) Strength Field 200 Watts 2 Watts 10 100 30 35 40 45 50 55 Frequency (GHz) ATH33G50 Gain (dBi) ATH33G50 3dB Beamwidth 24 12.5 23.8 12 H Plane 23.6 23.4 11.5 23.2 11 23 10.5 Degrees Gain (dBi) 22.8 22.6 10 E Plane 22.4 9.5 22.2 22 9 30 35 40 45 50 30 35 40 45 50 Frequency (GHz) Frequency (GHz) Page 2 of 2 .

Copy Link

Recommended publications

Analysis and Measurement of Horn Antennas for CMB Experiments
Analysis and Measurement of Horn Antennas for CMB Experiments Ian Mc Auley (M.Sc. B.Sc.) A thesis submitted for the Degree of Doctor of Philosophy Maynooth University Department of Experimental Physics, Maynooth University, National University of Ireland Maynooth, Maynooth, Co. Kildare, Ireland. October 2015 Head of Department Professor J.A. Murphy Research Supervisor Professor J.A. Murphy Abstract In this thesis the author's work on the computational modelling and the experimental measurement of millimetre and sub-millimetre wave horn antennas for Cosmic Microwave Background (CMB) experiments is presented. This computational work particularly concerns the analysis of the multimode channels of the High Frequency Instrument (HFI) of the European Space Agency (ESA) Planck satellite using mode matching techniques to model their farfield beam patterns. To undertake this analysis the existing in-house software was upgraded to address issues associated with the stability of the simulations and to introduce additional functionality through the application of Single Value Decomposition in order to recover the true hybrid eigenfields for complex corrugated waveguide and horn structures. The farfield beam patterns of the two highest frequency channels of HFI (857 GHz and 545 GHz) were computed at a large number of spot frequencies across their operational bands in order to extract the broadband beams. The attributes of the multimode nature of these channels are discussed including the number of propagating modes as a function of frequency. A detailed analysis of the possible effects of manufacturing tolerances of the long corrugated triple horn structures on the farfield beam patterns of the 857 GHz horn antennas is described in the context of the higher than expected sidelobe levels detected in some of the 857 GHz channels during flight.
[Show full text]
Development of Conical Horn Feed for Reflector Antenna
International Journal of Engineering and Technology Vol. 1, No. 1, April, 2009 1793-8236 Development of Conical Horn Feed For Reflector Antenna Jagdish. M. Rathod, Member, IACSIT and Y.P.Kosta, Senior Member IEEE waveguide that provides the impedance transformation Abstract—We have designed a antenna feed with prime between the waveguide impedance and the free-space concerned that with the growing conjunctions in the mobile impedance. Horn radiators are used both as antennas in their networks, the parabolic antenna are evolving as an useful device own right, and as illuminators for reflector antennas. Horn for point to point communications where the need for high antennas are not a perfect match to the waveguide, although directivity and high power density is at the prime importance. With these needs we have designed the unusual type of feed standing wave ratios of 1.5:1 or less are achievable. The gain antenna for parabolic dish that is used for both reception and of a horn radiator is proportional to the area A of the flared transmission purpose. This different frequency band open flange), and inversely proportional to the square of the performance having horn feed, works for the parabolic wavelength [8].Following Fig.1 gives types of Horn reflector antenna. We have worked on frequency band between radiators. 4.8 GHz to 5.9 GHz for horn type of feed. Here function of the horn is to produce uniform phase front with a larger aperture than that of the waveguide and hence greater directivity. Parabolic dish antenna is the most commonly and widely used antenna in communication field mainly in satellite and radar communication.
[Show full text]
Design and Analysis of Pyramidal Horn Antenna
www.ijcrt.org © 2020 IJCRT | Volume 8, Issue 3 March 2020 | ISSN: 2320-2882 Design and analysis of pyramidal Horn antenna 1 Mrs. Rikita Gohil, 2 Mrs. Niti P. Gupta Electronics and Communication Engineering Department S.V.I.T. Vasad, Gujarat, India Abstract: This paper discusses the design of a pyramidal horn antenna with high gain, suppressed side lobes. The horn antenna is widely used in the transmission and reception of RF microwave signals. Horn antennas are extensively used in the fields of T.V. broadcasting, microwave devices and satellite communication. It is usually an assembly of flaring metal, waveguide and antenna. The physical dimensions of pyramidal horn that determine the performance of the antenna. The length, flare angle, aperture diameter of the pyramidal antenna is observed. These dimensions determine the required characteristics such as impedance matching, radiation pattern of the antenna. The antenna gives gain of about 25.5 dB over operating range while delivering 10 GHz bandwidth. Ansoft HFSS 13 software is used to simulate the designed antenna. Pyramidal horn can be designed in a variety of shapes in order to obtain enhanced gain and bandwidth. The designed Pyramidal Horn Antenna is functional for each X-Band application. The horn is supported by a rectangular wave guide. Index Terms - Gain, Horn, Impedance, RF, Rectangular Waveguide, Return loss, Radiation pattern. INTRODUCTION Pyramidal horn is one type of aperture antenna flared in both directions, a combination of E-plane and H-plane horns. 3D figure is shown as Figure 1.Horn antennas are commonly used as a standard gain antenna for calibration purpose of other antennas.
[Show full text]
A Flexible 2.45 Ghz Rectenna Using Electrically Small Loop Antenna
A Flexible 2.45 GHz Rectenna Using Electrically Small Loop Antenna Khaled Aljaloud1,2, Kin-Fai Tong1 1Electronic and Electrical Engineering Department, University College London, London, UK, [email protected] 2Electrical Engineering Department, King Saud University, Riyadh, Saudi Arabia Abstract—We present the concept and design of a compact schlocky diode connected in series to one of the two feed flexible electromagnetic energy-harvesting system using electri- terminals of the antenna and to the coplanar transmission line, cally small loop antenna. In order to make the integration of the a capacitor to minimize the ripple level. The reported system system with other devices simpler, it is designed as an integrated system in such a way that the collector element and the rectifier in this letter is sufficiently capable of reusing low microwave circuit are mounted on the same side of the substrate. The energy for both flat and curved configurations. rectenna is designed and fabricated on flexible substrate, and its performance is verified through measurement for both flat and curved configurations. The DC output power and the efficiency II. DESIGN AND RESULT are investigated with respect to power density and frequency. It is observed through measurements that the proposed system The two main parts of rectenna system are largely designed can achieve 72% conversion efficiency for low input power level, individually and unified through the matching network. In this -11 dBm (corresponding power density 0.2 W=m2), while at the work, the proposed rectenna is built as an integral system, and same time occupying a smaller footprint area compared to the thus the rectifier circuit is matched to the collector to maximize existing work.
[Show full text]
An All Purpose High Gain Antenna for 2400 Mhz
Roger Paskvan, WAØIUJ 3516 Mill St NE, Bemidji, MN 56601, [email protected] An All Purpose High Gain Antenna for 2400 MHz Roger shows an easy to fabricate circular horn antenna that can be built using copper plumbing pipe and sheet copper. For those interested in a relatively easy Figure 1 – Side view mination in that application. With a simple way to build antenna for the 2400 MHz of the completed horn hood addition, this copper wonder will pro- antenna. band, the design described here might be vide 12 db of gain, now that’s 17 times! the answer. It features high gain, good cap- According to Kraus1 a horn antenna is ture area, and shielding from strong local regarded as an opened up waveguide. The signals. The antenna will operate in either function of this arrangement is to produce vertical or horizontal polarization as a func- dish. The possibilities for using this antenna an in-phase wave front thus providing tion of mounting. Design data with complete are limited by your imagination. Point to signal gain in a given direction. Signal is construction and tuning procedures take point communication of data and voice has injected into the waveguide by means of a the guesswork out of building this wonder been done over several miles. If you are small probe that must be critically placed. antenna, out of a simple copper pipe. lucky enough to have a shack in the back The type of horn described in this writing is This article provides a simple step-by- yard, two of these provide a great data link known as a cylindrical horn.
[Show full text]
Wireless Power Transmission with Circularly Polarized
WIRELESS POWER TRANSMISSION WITH CIRCULARLY POLARIZED RECTENNA Jwo-Shiun Sun 1, Ren-Hao Chen 1, Shao-Kai Liu 1, Cheng-Fu Yang 2, 1Graduate institute of computer and communication engineering National Taipei University of Technology, Taiwan 2Department of Chemical and Materials Engineering National University of Kaohsiung, Kaohsiung, Taiwan Abstract —Design of a novel circularly polarized (CP) rectenna (rectifying antenna) at 925MHz for wireless power transmission (WPT) applications involving wireless power transfer to low power consumption wireless device is proposed. In order to build the rectenna, a CP wide-slot antenna and a finite ground coplanar waveguide (CPW) circuit both with good impedance matching, have been developed. In addition, the size of the wide-slot antenna is smaller than the conventional slot antenna up to 60% when the meander line structure is adopted. The rectenna is the voltage-doubler rectifier with the low-pass filter (LPF) for efficiency optimization and higher order harmonics re-radiation elimination. According to the measured results, the maximum RF- to-DC conversion efficiency of the rectenna achieved 75% when the RF power of 15dBm is received with a load resistance of 2kΩ at free space. The experimental results prove that the proposed rectenna is suitable for the WPT applications. 1. INTRODUCTION Both wireless power transmission (WPT) [1] and solar power transmission (SPT) [2] are the promising techniques for the long-distance power supply of wireless applications, such as radio frequency identification (RFID) tags [3,4], wireless embedded sensors [5-7], medical implant with biotelemetry as a communication link [8,9], etc. The rectenna (rectifying antenna) is one of the most important components for above-mentioned techniques, which has great potential to deliver, collect and convert radio frequency (RF) energy into useful direct current (DC) power for neighbored electronic devices or to recharge batteries through free space without using the physical transmission line [10].
[Show full text]
Microwave Antenna Measurements
Engineering Sciences 151 Electromagnetic Communication Laboratory Assignment 5 Fall Term 1998-99 ELECTROMAGNETIC RADIATION CHARACTERISTICS Microwave Antenna Measurements OBJECTIVE: To study the radiation patterns and other characteristics of a variety of electromagnetic radiators (antennas). EXPERIMENTAL METHODS1 EXPERIMENTAL SETUP: EQUIPMENT: Sweep signal generator: 8 -12 GHz, Dorado International Corp. Model G4-197 Low-noise preamplifier, Stanford Research Systems, Model SR560 60 MHz Dual-channel oscilloscope, Tektronix, Model 2213A Microwave isolator, Bomac Laboratories, Model BLF-30 Slotted line section, Hewlett-Packard, Model 809B Variable attenuator, Hewlett-Packard, Model X382A Slide screw tuner, Hewlett-Packard, Model X870A Frequency meter, FXR, Model X401B 1 See Chapter 16, Antenna Measurements, in Antenna Theory (Second Edition), Constantine A. Balanis, ISBN 0- 471-59268-4. ELECTROMAGNETIC RADIATION PATTERNS PAGE 2 Detector mount, Hewlett-Packard, Model X485B and microwave crystal diode detectors, 1N21B or 1N23B Parabolic reflector (18 inch aperture diameter), Edmund Scientific Center-fed reflector antenna (30 cm diameter aperture), homemade Set of two small (5.4 cm x 7.3 cm) pyramidal horn antennas, Narda, Model 640 Large aperture (9 cm x 15 cm) pyramidal horn antennas, homemade Endfire helical antenna, homemade Microstrip patch antenna, homemade Three element array antenna driver, homemade Set of rotatable wooden antenna stands ), homemade Wooden frame for CATR reflector, homemade Two waveguide twist sections Flexible inspection light Sheets (24 x 24 inch) of microwave anechoic material Miscellaneous test parts including: waveguide and coax components and transistions; wire and aluminum foil;, etc.. GENERAL COMMENTS: The experimental setup, illustrated above, provides a means for studying the radiation patterns and other characteristics of electromagnetic antennas.
[Show full text]
Optimization Procedure for Wideband Matched Feed Design
Optimization Procedure for Wideband Matched Feed Design Michael Forum Palvig1,2, Erik Jørgensen2, Peter Meincke2, Olav Breinbjerg1 1Department of Electrical Engineering, Electromagnetic Systems, Technical University of Denmark, Kgs. Lyngby, Denmark 2TICRA, Copenhagen, Denmark Abstract—The inherently high cross polarization of prime focus of these feeds quickly deteriorate when the frequency moves offset reflector antennas can be compensated by launching higher away from the design frequency. To improve this, the full order modes in the feed horn. Traditionally, the bandwidth of desired frequency band must be included in the design op- such systems is in the order of a few percent. We present a novel design procedure where the entire matched feed and timizations. reflector system can be efficiently optimized. This allows the design parameters of the matched feed to be directly related II. REQUIRED MODES FOR MATCHED CONDITION to the desired design goals in the secondary pattern over a specified band. Using this procedure, we present a design of a As mentioned in the previous section, the fact that the die-castable axially corrugated matched feed horn that provides required extra circular waveguide mode is TE , is usually an XPD improvement better than 7 dB over a 12% bandwidth 21 for a reflector with an f/D of 0.5. An investigation of the mode justified from the focal region fields when a plane wave is requirement for an arbitrary circular aperture feed is also incident on the reflector [1] (described in more detail in [9]). presented. The method gives a good indication of the solution to the Index Terms—matched feed, reflector antenna, horn antenna, problem, but is not strictly rigorous.
[Show full text]
Thz Band Horn Antennas Design T.V
THPSM08 Proceedings of PAC2013, Pasadena, CA USA THZ BAND HORN ANTENNAS DESIGN T.V. Bondarenko, S.M. Polozov, A.Yu. Smirnov, National Research Nuclear University MEPhI, Moscow, Russia Abstract with 300 μm aperture and 31 μm polytetrafluoroethylene The report is concerned with the development of the coating on the metal surface. Resonant frequency of this irradiating antennas for THz radiation source. The THz type of capillary is 0.96 THz. Work band on the level of radiation is irradiated by relativistic high brightness -3 dB of the maximal power transmission is 3.2%. electron bunch traveling through the Cherenkov decelerating capillary channel [1]. Irradiation systems are CIRCULAR HORN ANTENNA built as horn antennas type with circular and rectangular Circular antenna is the most conventional type of cross-sections. Irradiating antennas are constructed antenna for such devices (Fig. 2). The model of the horn directly to the open end of the capillary channel and are was built and calculated using the CST Microwave Studio used for the THz radiation directivity enhancement after [3]. To define the maximum effective horn parameters the passing through the capillary output. The investigation of electrodynamics characteristics were studied while the horns directivities were performed using the far-field varying the horn geometrical parameters. The opening analysis of the emerging radiation. The antennas were angle was varied while the horn length was kept L=1 mm also investigated to perform low values of the reflected (fig. 3). After that with the angle equal 14.5 degrees (that power. corresponds to maximal directivity of the horn) length of the horn was varied (Fig.
[Show full text]
Low Cost Horn Antennas for 23 Cm EME By...Thomas Henderson, WD5AGO
Low Cost Horn Antennas for 23 cm EME By...Thomas Henderson, WD5AGO “What is the best antenna for EME?” is an online topic that crops up from time to time. “Lowest cost”, was added to another posting. The band of interest is 23 cm. Looking at the station log sheets, the most commonly used antenna for this band is the parabolic reflector (dish) followed by the yagi. Common is not quite accurate as out of the hundreds of earth-moon-earth (EME) contacts on this band only a couple were made with yagi stations. The only other antenna tested for 23 cm EME, in the receive mode only, was a mid size 15 dBi horn. It appears then the dish wins out and with a high efficiency feedhorn it is tough to beat. So which is the easiest, lowest cost antenna to construct? Value analysis of each the antennas noted above was made. A starting point would be to determine the antenna gain needed to make EME contacts. Over fifty 23 cm EME stations have excess gain and power levels to communicate with low power stations. This includes the small, commonly used 3 m dish. Over a dozen of those high gain/power stations will have over 10 dB gain to spare when communicating with the 3 m dish. This would place a minimum receiving antenna gain targeted around 20 dBi. At this gain level, reception of larger EME stations should be possible and with 250 W or more of power, contacts could also be made. For a 20 dBi gain antenna to have a higher EME success rate though, the ability to use circular polarization would be desirable.
[Show full text]
Development of Automobile Antenna Design and Optimization for Fm/Gps/Sdars Applications
DEVELOPMENT OF AUTOMOBILE ANTENNA DESIGN AND OPTIMIZATION FOR FM/GPS/SDARS APPLICATIONS DISSERTATION Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy in the Graduate School of The Ohio State University By Yongjin Kim, B.S., M.S. ***** The Ohio State University 2003 Dissertation Committee: Approved by Professor Edward H. Newman, Adviser ________________________________ Advisor Professor Eric K. Walton, Co-Adviser ________________________________ Professor Fernando Teixeira Co-Advisor Department of Electrical Engineering Professor Thomas E. Nygren Copyright by Yongjin Kim 2003 ABSTRACT The use of antennas for vehicle applications is growing very rapidly due to the development of modern wireless communication technology and service. The need for a computational tool to design and optimize new automobile antennas more simply and easily has been increasing. Currently, an automobile antenna design using the Simple Genetic Algorithm (SGA) has been introduced. In this model, the SGA computation tool attempts to obtain the best design based on a single cost function. The automobile antenna design is a multi- objective problem. The different objectives are combined into a single cost function, each with a weight value. The results of the optimization procedure depend strongly on these weights, and thus, the designer must properly choose each weight value to get the desired optimum. Also, all the weight values must then be changed, and the entire optimization procedure must be repeated whenever the designer wants to change any single objective goal. In addition, a single optimum solution obtained by the SGA can be unrealizable due to various limitations. Present SGA research has focused on antennas with limited geometric flexibility, such as simple wire antenna geometry.
[Show full text]
Antenna Measuring Notes
Antenna Measuring Notes: Kent Britain WA5VJB (Written for Scatterpoint issue 1-2000 updated Sept 2006) Since 1987 I have set up my portable antenna range at 26 Conferences measuring well over 1500 antennas, mainly in the 0.9 to 24 GHz range. G4DDK has asked me to list some of my observations. The Feed is not at the focus of the dish: First off, I have NEVER been able to calculate the focal point of my dish, mount the feed, and have the antenna optimized. NEVER! It always seems I have to move the feed in towards the dish a bit to tweak things up. But out of the antenna range things are far worse. About half of the dishes have the feed off by as much as 50% in distance! A chap comes up with a 2 ft. dish and about a 0.35 f/d. The feed is sticking out 3 ft from dish! "But that's where I calculated the focus to be!" is always the answer. I haven't found out what in the D²/16c equation throws them, but we see it all the time. Another problem is the rounded edge on most dishes. They measure the physical diameter of the dish, not the diameter of the actual parabolic surface. That outer cm or so of many dishes is not usable and should not be used in the F/d calculations. And I won’t even start on the complications of calculating the actual phase center of the feed. I have always been able to pick up a dB or two tweaking the focus and 6 dB or so has been the typical improvement at the conferences when the feed is movable and we can optimize its position.
[Show full text]