Display Hidden Notes to Specifier. (Don't Know How? Click Here) s82
Total Page：16
File Type：pdf, Size：1020Kb
SECTION 26 55 39 HELIPAD LIGHTING
Display hidden notes to specifier. (Don't know how? Click Here)
Copyright 2017 - 2017 ARCAT, Inc. - All rights reserved
1 GENERAL
1.1 SECTION INCLUDES
1.1.1 Perimeter Lights: 1.1.1.1 Pole mounted. 1.1.1.2 Pole mounted, NVG compatible. 1.1.1.3 Ground based. 1.1.1.4 Ground based, NVG compatible. 1.1.1.5 Inset perimeter light assembly. 1.1.1.6 Inset perimeter inset light assembly, NVG compatible.
1.1.2 Obstruction Lights: 1.1.2.1 Pole mounted dual red obstruction light. 1.1.2.2 L-810 ground-based red obstruction light. 1.1.2.3 L-810 pole mounted obstruction light.
1.1.3 Wind Cones: 1.1.3.1 Externally lit wind cones. 1.1.3.2 Internally lit wind cones.
1.1.4 Beacons.
1.1.5 26 55 39-1 Battery powered lights.
1.1.6 Flood lights.
1.1.7 Remote lighting controller.
1.2 RELATED SECTIONS
1.2.1 Section 13 34 16 - Grandstands and Bleachers.
1.2.2 Division 15 - Plumbing: Provisions for and connection to supplied equipment including controls and valves. 1.2.2.1 Fuel/water separator. 1.2.2.2 Hydronic snow melting system.
1.2.3 Division 16 - Electrical: Provisions for and connection to supplied equipment.
1.3 REFERENCES
1.3.1 Canadian Aviation Association (CAA).
1.3.2 Civil Aviation Authority (CAP): 1.3.2.1 CAP 437 - Standards for offshore helicopter landing areas.
1.3.3 Federal Aviation Association (FAA): 1.3.3.1 FAA AC 150/5390-2A - Heliport Design. 1.3.3.2 FAA AC 150/5390-2C - Heliport Design.
1.3.4 Federal Communications Commission (FCC).
1.3.5 Ingress Protection ratings defined in EN 60529 (IP).
1.3.6 International Civil Aviation Organization (ICAO): 1.3.6.1 ICAO Annex 14 - Aerodromes - Volume II Heliports.
1.3.7 International Standards (EN): 1.3.7.1 EN 60529 - Degrees of protection provided by enclosures.
1.3.8 International Organization for Standardization (ISO): 1.3.8.1 ISO 9000 - Quality Management Systems.
26 55 39-2 1.3.9 Intertek Group PLC, Independent Product Testing (ETL).
1.3.10 National Fire Protection Association: 1.3.10.1 NFPA 418: Standard for Heliports.
1.3.11 Restriction of Hazardous Substances Directive (RoHS).
1.3.12 Robust Header Compression, Data Compression Standardization (ROHC).
1.3.13 Underwriters Laboratories (UL): 1.3.13.1 UL 1598 - Luminaires. 1.3.13.2 UL 94 - Federal Communications Commission.
1.3.14 Underwriters Laboratories Canada (cUL).
1.3.15 Unites States Military specifications (MIL): 1.3.15.1 MIL-I-45208A - Inspection System Requirements.
1.4 SUBMITTALS
1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.
1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including: 1.4.2.1 Preparation instructions and recommendations. 1.4.2.2 Storage and handling requirements and recommendations. 1.4.2.3 Installation methods.
1.4.3 Shop Drawings: 1.4.3.1 Submit complete fabrication details, design calculations, and erection Drawings, bearing the registered structural engineer's stamp, to the Local Building Code Official.
1.4.4 Certification/Permits: 1.4.4.1 Manufacturer is responsible for FAA submittal process and will submit evidence of Airspace Certification from the FAA.
1.5 QUALITY ASSURANCE
1.5.1 Manufacturer Qualifications: 1.5.1.1
26 55 39-3 Manufacturer shall have an approved and documented quality control system equal to Mil-I-45208A or ISO 9000.
1.5.2 Installer Qualifications: Contractor shall be financially responsible for obtaining any permits as they apply to the system installation and operation.
1.6 DELIVERY, STORAGE, AND HANDLING
1.7 Store products in manufacturer's unopened packaging, out of extreme heat or direct sunlight, until ready for installation. Do not switch fixtures ON until protective peel is removed from reflectors and/or lenses.
1.8 PROJECT CONDITIONS
1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
1.9 WARRANTY
1.9.1 Warranty Period: Manufacturer warrants our manufactured products and installed systems for 12 months.
1.9.2 Product Warranty: Manufacturer will repair or replace any parts that Manufacturer determines are defective during the warranty period.
1.9.3 System Warranty: Manufacturer will repair or replace any parts or components of the system that Manufacturer determines are defective during the warranty period.
1.9.4 Customer's Obligations: The Customer shall notify Manufacturer of any defects or problems with a part or system within 30 days of the date that the defects or problems were discovered or should have been discovered; failure to notify Manufacturer within this 30-day period shall nullify the warranty regarding that defect or problem.
1.9.5 Maintenance: The Customer is responsible for preventive and routine maintenance.
1.9.6 Extension of Warranty: The warranty period shall not be extended.
1.9.7 Discrete Warranty Claim: When the system returns to normal operation for a 30-day period following action by Manufacturer and the Customer under this warranty, the defect or problem shall be considered resolved.
1.9.8 Other Warranty Provisions: Customer may not assign this Warranty to any other person or business entity, including a successor in interest to the Customer, without Manufacturer's written consent.
2 PRODUCTS
2.1 26 55 39-4 MANUFACTURERS
2.1.1 Acceptable Manufacturer: FEC Heliports, which is located at: 5298 River Rd.; Cincinnati, OH 45233; Toll Free Tel: 877-HELIPAD; Tel: 513-621-5260; Fax: 513-621-0524; Email: request info ([email protected]); Web: www.FECHeliports.com
2.1.2 Substitutions: Not permitted.
2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
2.2 PERIMETER LIGHTS
2.2.1 Pole Mounted Perimeter Lights: 2.2.1.1 Standards Compliance: 2.2.1.1.1 CAP 437. 2.2.1.1.2 ICAO Annex 14. 2.2.1.1.3 FAA and CAA. 2.2.1.1.4 UL1598. 2.2.1.1.5 ETL. 2.2.1.2 Powder coated high-visibility yellow cast aluminum body. High tempered glass lens Pre-wired for installation. 2.2.1.3 Electrical Characteristics: 2.2.1.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.2.1.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.1.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.2.1.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.2.1.3.5 Operating LED Lifespan: Greater than 50,000 hours. 2.2.1.3.6 Light Source: 2.2.1.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.2.1.3.6.2 Average Power Consumption: 3.5 W. 2.2.1.3.6.3 Constant Current Supply: 350 mA. 2.2.1.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.2.1.3.6.5 RoHS and 94VO compliant. 2.2.1.4 Standard Colors: 2.2.1.4.1
26 55 39-5 True green (528 nm). 2.2.1.4.2 Blue (470 nm). 2.2.1.4.3 White 6000 K. 2.2.1.4.4 Yellow/amber (590 nm). 2.2.1.5 Physical Characteristics: 2.2.1.5.1 Degree of Protection: IP66. 2.2.1.5.2 Height: 5-3/4 in (146 mm). 2.2.1.5.3 Outside Diameter: 3-7/8 in (98 mm). 2.2.1.6 Materials: 2.2.1.6.1 Lens: Tempered Glass. 2.2.1.6.2 Casting: 356 T6 Aluminum Alloy. 2.2.1.6.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.2.1.7 Shipping Weight: 3 lbs (1.4 kg).
2.2.2 Pole Mounted Perimeter Lights, NVG Compatible: 2.2.2.1 Standards Compliance: 2.2.2.1.1 CAP 437. 2.2.2.1.2 ICAO Annex 14. 2.2.2.1.3 FAA and CAA. 2.2.2.1.4 UL1598. 2.2.2.1.5 ETL. 2.2.2.2 Powder coated high-visibility yellow cast aluminum body. High tempered glass lens Pre-wired for installation. 2.2.2.3 Electrical Characteristics: 2.2.2.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.2.2.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.2.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.2.2.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.2.2.3.5 Operating LED Lifespan: Greater than 50,000 hours. 2.2.2.3.6 Light Source: 2.2.2.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.2.2.3.6.2 Average Power Consumption: 3.5 W. 26 55 39-6 2.2.2.3.6.3 Constant Current Supply: 350 mA. 2.2.2.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.2.2.3.6.5 RoHS and UL 94 V-0 compliant. 2.2.2.4 Standard Colors: 2.2.2.4.1 True Green (528 nm). 2.2.2.4.2 Blue (470 nm). 2.2.2.4.3 White 6000 K. 2.2.2.4.4 Yellow/amber (590 nm). 2.2.2.5 NVG Compatible: 2.2.2.5.1 Three true green LEDs and two IR LEDs (IR LEDs 850nm). 2.2.2.5.1.1 Clear lens provided with IR LED lights. 2.2.2.6 NVG Characteristics: 2.2.2.6.1 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.2.6.2 Consumption: 6 watts, .1 amps at 277 V. 2.2.2.7 Physical Characteristics: 2.2.2.7.1 Degree of Protection: IP66. 2.2.2.7.2 Height: 5-3/4 in (146 mm). 2.2.2.7.3 Outside Diameter: 3-7/8 in (98 mm). 2.2.2.8 Materials: 2.2.2.8.1 Lens: Tempered Glass. 2.2.2.8.2 Casting: 356 T6 Aluminum Alloy. 2.2.2.8.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.2.2.9 Shipping Weight: 3 lbs (1.4 kg).
2.2.3 Ground-Based Perimeter Light, NVG Compatible. 2.2.3.1 Standards Compliance: 2.2.3.1.1 CAP 437. 2.2.3.1.2 ICAO Annex 14. 2.2.3.1.3 FAA and CAA. 2.2.3.1.4 UL1598. 2.2.3.1.5 ETL. 2.2.3.2 26 55 39-7 Powder coated high-visibility yellow cast aluminum body. High tempered glass lens Pre-wired for installation. 2.2.3.3 Electrical Characteristics: 2.2.3.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.2.3.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.3.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.2.3.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.2.3.3.5 Operating LED Lifespan: Greater than 50,000 hours. 2.2.3.3.6 Light Source: 2.2.3.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.2.3.3.6.2 Average Power Consumption: 3.5 W. 2.2.3.3.6.3 Constant Current Supply: 350 mA. 2.2.3.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.2.3.3.6.5 RoHS and 94VO compliant. 2.2.3.4 Standard Colors: 2.2.3.4.1 True Green (528 nm). 2.2.3.4.2 Blue (470 nm). 2.2.3.4.3 White 6000 K. 2.2.3.4.4 Yellow/amber (590 nm). 2.2.3.5 NVG Compatible: 2.2.3.5.1 Three true green LEDs and two IR LEDs (IR LEDs 850 nm). 2.2.3.5.1.1 Clear lens provided with IR LED lights. 2.2.3.6 NVG Characteristics: 2.2.3.6.1 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.3.6.2 Consumption: 6 watts, .1 amps at 277 V. 2.2.3.7 Physical Characteristics: 2.2.3.7.1 Degree of Protection: IP66. 2.2.3.7.2 Height 4-1/16 in (104 mm). 2.2.3.7.3 Outside Diameter 3-7/8 in (98 mm). 2.2.3.8 Materials: 2.2.3.8.1 Lens: Tempered Glass. 2.2.3.8.2 26 55 39-8 Casting: 356 T6 Aluminum Alloy. 2.2.3.8.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.2.3.9 Shipping Weight: 3 lbs (1.4 kg).
2.2.4 Inset Perimeter Light Assembly: 2.2.4.1 Standards Compliance: 2.2.4.1.1 CAP 437. 2.2.4.1.2 ICAO Annex 14. 2.2.4.1.3 FAA and CAA. 2.2.4.1.4 UL1598. 2.2.4.1.5 ETL. 2.2.4.2 Powder coated high-visibility yellow cast aluminum body. High tempered glass lens Pre-wired for installation. 2.2.4.3 Electrical Characteristics: 2.2.4.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.2.4.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.4.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.2.4.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.2.4.3.5 Operating LED Lifespan: Greater than 50,000 hours. 2.2.4.3.6 Light Source: 2.2.4.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.2.4.3.6.2 Average Power Consumption: 3.5 W. 2.2.4.3.6.3 Constant Current Supply: 350 mA. 2.2.4.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.2.4.3.6.5 RoHS and 94VO compliant. 2.2.4.4 Standard Colors: 2.2.4.4.1 True Green (528 nm). 2.2.4.4.2 Blue (470 nm). 2.2.4.4.3 White 6000 K. 2.2.4.4.4 Yellow/amber (590 nm). 2.2.4.5 Physical Characteristics: 2.2.4.5.1 Degree of Protection: IP66. 26 55 39-9 2.2.4.5.2 Height: 5 in (127 mm). 2.2.4.5.3 Outside Diameter: 10 in (254 mm). 2.2.4.5.4 Inside Diameter: 4 in (102 mm). 2.2.4.6 Materials: 2.2.4.6.1 Lens: Tempered glass. 2.2.4.6.2 Casting: 356 T6 aluminum alloy. 2.2.4.6.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.2.4.7 Shipping Weight: 4 lbs (1.8 kg). 2.2.4.8 Mounting Can: 2.2.4.8.1 Height: 6-5/8 in (168 mm). 2.2.4.8.2 Outside Diameter: 11 in (279 mm). 2.2.4.8.3 Inside Diameter: 8-1/2 in (216 mm). 2.2.4.8.4 Casting: 356 T6 aluminum alloy 2.2.4.8.5 Shipping Weight: 6 lbs (2.7 kg).
2.2.5 Inset Perimeter Light Assembly, NVG Compatible: 2.2.5.1 Standards Compliance: 2.2.5.1.1 CAP 437. 2.2.5.1.2 ICAO Annex 14. 2.2.5.1.3 FAA and CAA. 2.2.5.1.4 UL1598. 2.2.5.1.5 ETL. 2.2.5.2 Powder coated high-visibility yellow cast aluminum body. High tempered glass lens Pre-wired for installation. 2.2.5.3 Electrical Characteristics: 2.2.5.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.2.5.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.5.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.2.5.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.2.5.3.5 Operating LED Lifespan: Greater than 50,000 hours. 2.2.5.3.6 Light Source: 2.2.5.3.6.1 26 55 39-10 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.2.5.3.6.2 Average Power Consumption: 3.5 W. 2.2.5.3.6.3 Constant Current Supply: 350 mA. 2.2.5.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.2.5.3.6.5 RoHS and 94VO compliant. 2.2.5.4 Standard Colors: 2.2.5.4.1 True Green (528 nm). 2.2.5.4.2 Blue (470 nm). 2.2.5.4.3 White 6000 K. 2.2.5.4.4 Yellow/amber (590 nm). 2.2.5.5 NVG Compatible: 2.2.5.5.1 Three true green LEDs and two IR LEDs (IR LEDs 850nm). 2.2.5.5.1.1 Clear lens provided with IR LED lights. 2.2.5.6 NVG Characteristics: 2.2.5.6.1 Maximum Power: 6 watts, .2 amps at 120 V. 2.2.5.6.2 Consumption: 6 watts, .1 amps at 277 V. 2.2.5.7 Physical Characteristics: 2.2.5.7.1 Degree of Protection: IP66. 2.2.5.7.2 Height: 5 in (127 mm). 2.2.5.7.3 Outside Diameter: 10 in (254 mm). 2.2.5.7.4 Inside Diameter: 4 in (102 mm). 2.2.5.8 Materials: 2.2.5.8.1 Lens: Tempered glass. 2.2.5.8.2 Casting: 356 T6 aluminum alloy. 2.2.5.8.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.2.5.9 Shipping Weight: 4 lbs (1.8 kg). 2.2.5.10 Mounting Can: 2.2.5.10.1 Height: 6-5/8 in (168 mm). 2.2.5.10.2 Outside Diameter: 11 in (279 mm). 2.2.5.10.3 Inside Diameter: 8-1/2 in (216 mm). 2.2.5.10.4 Casting: 356 T6 aluminum alloy 2.2.5.10.5 26 55 39-11 Shipping Weight: 6 lbs (2.7 kg).
2.3 OBSTRUCTION LIGHTS
2.3.1 Pole Mounted Dual Red Obstruction Light: 2.3.1.1 Standards/Certification: 2.3.1.1.1 CAP 437. 2.3.1.1.2 ICAO Annex 14. 2.3.1.1.3 FAA & CAA. 2.3.1.1.4 UL1598. 2.3.1.2 Powder coated high-visibility yellow cast aluminum body. Low profile glass lens Pre- wired for installation. 2.3.1.3 Electrical Characteristics: 2.3.1.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.3.1.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.3.1.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.3.1.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.3.1.3.5 Life Span: Greater than 50,000 hours. 2.3.1.4 Physical characteristics: 2.3.1.4.1 1 in NPT (25 DN) hub for pole mounting. 2.3.1.4.2 Shipping weight: 30 lbs (13.6 kg). 2.3.1.4.3 Degree of Protection: IP66.
2.3.2 L-810 Ground-Based Red Obstruction Light: 2.3.2.1 Standards/Certification: 2.3.2.1.1 CAP 437. 2.3.2.1.2 ICAO Annex 14. 2.3.2.1.3 FAA & CAA. 2.3.2.1.4 UL1598. 2.3.2.1.5 ETL. 2.3.2.2 Powder coated high-visibility yellow cast aluminum body. Low profile glass lens Pre- wired for installation. 2.3.2.3 Electrical Characteristics: 2.3.2.3.1 26 55 39-12 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.3.2.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.3.2.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.3.2.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.3.2.3.5 Life Span: Greater than 50,000 hours. 2.3.2.3.6 Light Source: 2.3.2.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.3.2.3.6.2 Average Power Consumption: 3.5 W. 2.3.2.3.6.3 Constant Current Supply: 350 mA. 2.3.2.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.3.2.3.6.5 RoHS and 94VO compliant. 2.3.2.3.7 Standard Color: Red (632 nm). 2.3.2.4 Physical Characteristics: 2.3.2.4.1 Height: 4-1/16 in (103 mm). 2.3.2.4.2 Height: 7-1/16 in (179 mm). 2.3.2.4.3 Outside Diameter: 3 7/8 (98 mm). 2.3.2.4.4 Bolt Circle for Mounting: 5-1/2 in (139.7 mm). 2.3.2.4.5 Materials: 2.3.2.4.5.1 Lens: Tempered glass. 2.3.2.4.5.2 Casting: 356 T6 aluminum alloy. 2.3.2.4.5.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.3.2.4.6 Degree of protection: IP66. 2.3.2.5 Shipping weight: 4lbs.
2.3.3 L-810 Pole Mounted Red Obstruction Light: 2.3.3.1 Standards/Certification: 2.3.3.1.1 CAP 437. 2.3.3.1.2 ICAO Annex 14. 2.3.3.1.3 FAA & CAA. 2.3.3.1.4 UL1598. 2.3.3.1.5 ETL. 2.3.3.2 26 55 39-13 Powder coated high-visibility yellow cast aluminum body. Low profile glass lens Pre- wired for installation. 2.3.3.3 Electrical Characteristics: 2.3.3.3.1 Operating Voltage: 120 to 277 V, 50/60 Hz. 2.3.3.3.2 Maximum Power: 6 watts, .2 amps at 120 V. 2.3.3.3.3 Consumption: 6 watts, .1 amp at 277 V. 2.3.3.3.4 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.3.3.3.5 Life Span: Greater than 50,000 hours. 2.3.3.3.6 Light Source: 2.3.3.3.6.1 Omni-directional LED Lamp 3x Osram OSLONTM SSL 150O LEDs. 2.3.3.3.6.2 Average Power Consumption: 3.5 W. 2.3.3.3.6.3 Constant Current Supply: 350 mA. 2.3.3.3.6.4 Aluminum Circuit Diameter: 2 in (50 mm). 2.3.3.3.6.5 RoHS and 94VO compliant. 2.3.3.3.7 Standard Color: 2.3.3.3.7.1 Red LEDs (632 nm). 2.3.3.3.7.2 Red with IR LEDs (632nm) for NVG compatibility. 2.3.3.4 Physical Characteristics: 2.3.3.4.1 Height: 5-3/4 inches tall (146 mm). 2.3.3.4.2 Hub for Pole Mounting: 1 in NPT (25 DN). 2.3.3.4.3 Outside Diameter: 3 7/8 (98 mm). 2.3.3.4.4 Bolt Circle for Mounting: 5-1/2 in (139.7 mm). 2.3.3.4.5 Materials: 2.3.3.4.5.1 Lens: Tempered glass. 2.3.3.4.5.2 Casting: 356 T6 aluminum alloy. 2.3.3.4.5.3 Powder Coat: SW NL YELLOW PYS8-C8289. 2.3.3.4.6 Degree of protection IP66. 2.3.3.5 Shipping weight: 4lbs.
2.4 WIND CONES
2.4.1 Externally Lit Wind Cones: 2.4.1.1 26 55 39-14 Powder coated high visibility international orange housings. High tempered glass lens. Pre-wired for installation. 2.4.1.2 Electrical Characteristics: 2.4.1.2.1 Operating Voltage: 120 to 277 V, 50/60Hz. 2.4.1.2.2 Maximum Power Consumption: 2.4.1.2.2.1 78 watts, 0.65 amps at 120 V. 2.4.1.2.2.2 78 watts, 0.28 amps at 277 V. 2.4.1.2.3 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.4.1.2.4 Life Span: Greater than 50,000 hours. 2.4.1.2.5 Light Source: 2.4.1.2.5.1 Floodlights: Four LED par 38 spotlight, COB, 18 W, clear lens. 2.4.1.2.5.2 Obstruction Light: 2.4.1.2.5.2.1 One omni-directional LED lamp. 2.4.1.2.5.2.2 3x Osram OSLONTM SSL 150O LEDs. 2.4.1.2.5.2.3 Average Power Consumption: 3.5 W. 2.4.1.2.5.2.4 Constant Current Supply: 350 mA. 2.4.1.2.5.2.5 Aluminum Circuit Diameter: 2 in (50 mm). 2.4.1.2.5.2.6 RoHS and 94VO compliant. 2.4.1.3 Physical Characteristics: 2.4.1.3.1 Height: 10 ft (3.05 m) from base to top. 2.4.1.3.2 Height (ft / m): _____. 2.4.1.3.3 Base: Four 3/4 in (19 mm) holes on a 7 (178 mm) bolt circle. 2.4.1.3.4 Shipping weight: 50 lbs (22.7 kg). 2.4.1.4 Windsock: 18 by 6 in (457 by 152 mm). 2.4.1.5 Windsock: 18 by 8 in (457 by 203 mm).
2.4.2 Internally Lit Wind Cones 2.4.2.1 Powder coated high visibility international orange housings. High tempered glass lens. Pre-wired for installation. 2.4.2.2 Electrical Characteristics: 2.4.2.2.1 Operating Voltage: 120 to 277 V, 50/60Hz. 2.4.2.2.2 Maximum Power Consumption: 2.4.2.2.2.1 26 55 39-15 42 watts, .65 amps at 120 V. 2.4.2.2.2.2 42 watts, .28 amps at 277 V. 2.4.2.2.3 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.4.2.2.4 Life Span: Greater than 50,000 hours. 2.4.2.2.5 Light Source: 2.4.2.2.5.1 Floodlights: Two LED par 38 spotlight, COB, 18 W, clear lens. 2.4.2.2.5.2 Obstruction Light: 2.4.2.2.5.2.1 One omni-directional LED lamp. 2.4.2.2.5.2.2 3x Osram OSLONTM SSL 150O LEDs. 2.4.2.2.5.2.3 Average Power Consumption: 3.5 W. 2.4.2.2.5.2.4 Constant Current Supply: 350 mA. 2.4.2.2.5.2.5 Aluminum Circuit Diameter: 2 in (50 mm). 2.4.2.2.5.2.6 RoHS and 94VO compliant. 2.4.2.3 Physical Characteristics: 2.4.2.3.1 Height: 10 ft (3.05 m) from base to top. 2.4.2.3.2 Height (ft / m): _____. 2.4.2.3.3 Base: Four 3/4 in (19 mm) holes on a 7 (178 mm) bolt circle. 2.4.2.3.4 Shipping weight: 50 lbs (22.7 kg). 2.4.2.4 Windsock: 18 by 6 in (457 by 152 mm). 2.4.2.5 Windsock: 18 by 8 in (457 by 203 mm).
2.5 BEACONS
2.5.1 LED Programmable Locating Beacon: 2.5.1.1 Powder coated high-visibility yellow cast aluminum body suitable. Single or three color options. No moving parts. Pre-wired for installations. Excellent long range visibility. Programmable flash rate. 2.5.1.2 Standards Compliance: 2.5.1.2.1 CAP 437. 2.5.1.2.2 FAA. 2.5.1.2.3 ICAO. 2.5.1.3 Electrical Characteristics: 2.5.1.3.1 Operating Voltage: 100 to 230 V, 50/60 Hz. 26 55 39-16 2.5.1.3.2 Absolute Voltage Range: 40 to 55 VDC. 2.5.1.3.3 Average Power Consumption: Less than 20 watts. 2.5.1.3.4 Electrical Protection: On-board 4 A fuse (spare fuse on board) and polarity protection. 2.5.1.3.5 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.5.1.3.6 Life Span: Greater than 50,000 plus hours. 2.5.1.3.7 Relay contact output for alarm monitoring. 2.5.1.4 Standard LED Color Characteristics: 2.5.1.4.1 White: 6000 to 6500 degrees K ' Cool White.' 2.5.1.4.2 Green: 528 nm. 2.5.1.4.3 Yellow: 590 nm. 2.5.1.5 Optional LED Color Characteristics: 2.5.1.5.1 Red 625 nm. 2.5.1.5.2 Red-Orange 617 nm. 2.5.1.5.3 Hyper Red 656 nm. 2.5.1.5.4 Deep Blue 455 nm. 2.5.1.6 Physical Characteristics: 2.5.1.6.1 Height: 7-1/16 inches (178 mm). 2.5.1.6.2 Hub for Pole Mounting: 1 in NPT (25 DN). 2.5.1.6.3 Locating pin in base to enable precise orientation for quadrant management. 2.5.1.6.4 Operating temperature: Minus 13 to 122 degrees F (Minus 25 to 50 degrees C). 2.5.1.6.5 Storage temperature: Minus 13 to 176 degrees F (Minus 25 to 80 degrees C). 2.5.1.6.6 Long-life, quiet, low-power Internal cooling fan. 2.5.1.6.7 Shipping Weight: 18 lbs (8.1 kg). 2.5.1.6.8 Housing: Cast aluminum. 2.5.1.6.9 Powder Coat: SW NL YELLOW PYS8-C8289. 2.5.1.6.10 Degree of Protection: IP66. 2.5.1.7 Level Setting Switches: 2.5.1.7.1 Brightness Settings: 4 levels. 2.5.1.7.1.1 Level One: 100 percent (Factory set default). 2.5.1.7.1.2 26 55 39-17 Level Two: 60 percent. 2.5.1.7.1.3 Level Three: 30 percent. 2.5.1.7.1.4 Level Four: 10 percent 2.5.1.8 Operation Modes: 2.5.1.8.1 FAA L-802H Civil Helipad Beacon: 36 flashes per minute (FPM), 75ms pulse width. 2.5.1.8.2 US Army Helipad Pattern (as per TM 5-811-5): 36 FPM, 50ms pulses white (double Peak) - green - yellow. 2.5.1.8.3 FAA L-802M Military Helipad Beacon: 17.3 FPM, 100ms pulse width. 2.5.1.8.4 Location Beacon Modes: 2.5.1.8.4.1 Modified ICAO pattern: 30 FPM (short 2 ms and long 25 ms pulse) 2.5.1.8.4.2 UK CAA and Transport Canada Timing Compliant: 25 FPM 2.5.1.8.5 Morse Beacon Modes: 4 and 6 WPM (Words Per Minute): 1, 2 and 3 character code options. 2.5.1.8.6 Rotating (simulated) and flashing beacon modes. 2.5.1.8.7 Provision for an additional 8 custom patterns.
2.6 BATTERY POWERED LIGHTS
2.6.1 HEMS-Star (Set of 8 Helipad Battery Lights): 2.6.1.1 Standards Compliance: 2.6.1.1.1 FCC certification for operation in the US, and CE certification for the European Union. 2.6.1.2 Portable Battery Powered LED Helipad Lighting System: Microprocessor controlled light system designed for rapid deployment in temporary and emergency situations to provide safe and effective marking on a variety of terrains. 2.6.1.3 Operational Capabilities: 2.6.1.3.1 NVG Compatible: Red, blue, green, white visible LED's and infra-red. Programmable to show steady-on, flash warning, location beacon or morse code with the option of automatic sunset switching. 2.6.1.3.2 UHF Transceiver: Each light or set of lights can be programmed, interrogated and controlled by wireless commands. 2.6.1.3.3 System Control: Remote lighting controller, personal computer, or tablet with Zulu "dongle" transceiver and USB connector provided with each case as standard. Set up, test and control groups of lights via UHF transceiver. 2.6.1.3.4 Weight: Less than 2.2 lbs (1 kg). A full case of eight lights weighs 23.4 lbs (10.6 kg). 2.6.1.3.5 Rechargeable: In case via mains at 100 to 240 VAC or 13.5 to 28 VDC input from vehicles, solar, or wind power. 26 55 39-18 2.6.1.3.6 Degree of Protection: IP65. 2.6.1.3.7 Base: Stainless steel, successfully tested at the Sikorsky Development Flight Centre for stability under the full rotor wash of a CH-147 (Chinook). 2.6.1.3.8 Run Time Steady: 18 hours. 2.6.1.3.9 Run Time Flashing: 108 hours. 2.6.1.3.10 Recharging Time: 3.5 hours fully exhausted to fully charged.
2.7 FLOOD LIGHTS
2.7.1 LED Hooded Deck Floodlight: 2.7.1.1 Standards Compliance: UL and cUL listed. RoHS compliant and waterproof. 2.7.1.2 Powder coated high visibility yellow cast aluminum housing. Pre-wired for installation. 2.7.1.3 Operating voltage: 120 to 277 V, 50/60 Hz. 2.7.1.4 Power: 36 watts, 0.3 amps at 120 V maximum. 2.7.1.5 Consumption: 36 watts, 0.13 amps at 277 V. 2.7.1.6 Operating Temperature: 14 to 113 degrees F (minus 10 to 45 degrees C). 2.7.1.7 Operating LED Lifespan: Greater than 40,000 hours. 2.7.1.8 Powder Coat: SW NL YELLOW PYS8-C8289. 2.7.1.9 Light Source: 2.7.1.9.1 Two LED PAR 38 Clear Spotlight. 2.7.1.9.2 Lumens: 1300 to 1500 per bulb. 2.7.1.10 Degree of Protection: IP 65 (indoor and outdoor use).
2.7.2 LED Mini-Floodlights (Walkway Lighting): 2.7.2.1 Powered coated white cast aluminum housing with Finned heat sink. Clear micro- prismatic tempered glass lens. White cast metal visor. Pre-wired for installation. 2.7.2.2 Head Position: Adjustable. 2.7.2.3 Reflector: Molded textured plastic with semi-diffuse finish. 2.7.2.4 One circuit board with 30 LEDs. 2.7.2.5 Lifespan: Greater than 100,000 hours. 2.7.2.6 Electrical Characteristics: 2.7.2.6.1 Operating Voltage 120 V at 0.10 A. 2.7.2.6.2 Power: 12 watts. 26 55 39-19 2.7.2.6.3 Lumens: 957. 2.7.2.7 Physical Characteristics: 2.7.2.7.1 Height: 4 1/2" (114 mm). 2.7.2.7.2 Depth: 4 3/4" (121 mm). 2.7.2.7.3 Attachment Hardware: 1/2 in threaded stud (12.7 mm).
2.8 REMOTE LIGHTING CONTROLLERS
2.8.1 FEC Remote Lighting Controller: 2.8.1.1 Standards Compliance: ROHC Compliant 2.8.1.2 Features: 2.8.1.2.1 Simple frequency setting through front panel. 2.8.1.2.2 Number of Presses to Activate Circuits: 1, 2 or 3. 2.8.1.2.3 Remotely Activate Circuits: 1, 2 or 3 and have the status sent straight back to your mobile. 2.8.1.2.4 Programmable timeout with optional flashes to indicate end of on period. 2.8.1.2.5 VHF operation can be remotely enabled and disabled for extra security. 2.8.1.2.6 Secure PIN code protected SMS commands. 2.8.1.2.7 Secure SMS status reporting. 2.8.1.2.8 Local and remote test and diagnostics integrated into the unit 2.8.1.3 Controller Mode Options: 2.8.1.3.1.1 VHF and PCL 2.8.1.3.1.1.1 VHF Frequency Range: 118 to 136 MHz. 2.8.1.3.1.1.2 Channel Spacing (current): 25 kHz. 2.8.1.3.1.1.3 Channel Spacing (future): 8.33 kHz. 2.8.1.3.1.1.4 Frequency Selection: Any channel or UNICOM. 2.8.1.3.1.1.5 VHF Aerial: External remote mounted. 2.8.1.3.1.2 GSM/SMS or both. 2.8.1.3.1.2.1 GSM Bands: Tri-Band. 2.8.1.3.1.2.2 GSM Aerial Options: Internal to unit or remote mounted. 2.8.1.4 Network: Operators choice subject to coverage. 2.8.1.5 Tariff: Account or pre-pay. 2.8.1.6 26 55 39-20 Degree of Protection: IP65. 2.8.1.7 LCD and Keypad Protection: IP65 and ' vandal resistant.' 2.8.1.8 Operating Temperature: Minus 13 to 122 degrees F (minus 25 to 50 degrees C). 2.8.1.9 System Storage Temperature: Minus 13 to 176 degrees F (minus 25 to 80 degrees C). 2.8.1.10 Voltage: 2.8.1.10.1 Operating (AC): 100 to 240 VAC 50/60 Hz. 2.8.1.10.2 Operating (DC): 12 VDC. 2.8.1.10.3 Range (DC): 10V to 15 VDC. 2.8.1.11 Power: 2.8.1.11.1 Standby: 2 watts (approximate). 2.8.1.11.2 Transmitting: 10 watts (maximum). 2.8.1.11.3 Consumption: 30 watts (including optional winter heater) maximum. 2.8.1.12 Relay Capacity: 2 off, 20 A Relays (1 NO, 1 NC) DIN rail mounting option of third relay. 2.8.1.13 Dimensions (H x D x W): 11 x 6.5 x 7 in (280 x 165 x 180 mm). 2.8.1.14 Weight: 5.5 lbs (2.5kg).
3 EXECUTION
3.1 EXAMINATION
3.1.1 Do not begin installation until substrates have been properly prepared. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2 PREPARATION
3.2.1 Clean surfaces thoroughly prior to installation. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3 INSTALLATION
3.3.1 Install in accordance with manufacturer's latest published requirements, instructions, specifications, details and approved Shop Drawings. 3.3.1.1 Install fixtures in proper relationship with helipad and adjacent components. 3.3.1.2 Install fixtures with clearances recommended by manufacturer. 3.3.1.3 Install lamps and test for proper operation. 26 55 39-21 3.3.2 Manufacturer shall provide full-time installation crew to coordinate installation. Contractor shall certify in writing at completion that system is installed in accordance with manufacturer's recommendations.
3.3.3 Manufacturer shall coordinate requirements for on-site support required for installation of items supplied, and is responsible for supplying and delivering to the site components required for complete and usable installation whether or not shown or specified by these documents.
3.4 PROTECTION
3.4.1 Protect installed products until completion of project. Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
26 55 39-22