Chapter 1: Main Technical Parameters for WEWON-8330A-2

01. Implementation components are imported with reliable quality: Actuators are used in Japan SMC pneumatic components: precision pressure regulator (ensure pressure precision and adjustable), solenoid valves, oil water separator (pneumatic components ensure durability use), single-acting cylinders, etc 02. Adopt Japan's Mitsubishi Mitsubishi PLC programmable controller and LCD touch screen for program control: Meet requirement that countering and sorting test at the same time. 03. Simulation Test: Pressure can be on positive side , adjustable and intervals pressure can be adjustable to meet the greatest extent that phone key to combat resistant in practical use. 04. Probe height and interval can be adjustable : Measured interval direction on up and down or right and left can be adjustable to meet various specifications of the phone's basic key test. 05. Independent action: Chinese program , A, B; 2 independent working operation (sorting test 、simultaneous test), no need to disturbing each other; can be measured simultaneously or a set of two groups of three groups; 06. Max to 12 probe design: Each set has 6 cylinders((4mm cylinders, pressure 80 ~ 500gf), to meet the multi-button testing requirements, improve test efficiency, one cylinder for school force; 07. Precise pressure control: Using precision pressure regulator (multi-turn voltage regulator) regulator, and with special force unit to adjust school pressure, the pressure accurate and truly reflect the key fatigue performance.

Chapter 2: The Product Configurations for WEWON-8330A-2

Products Model Quantity Brand Lifetime 1 LCD touch screen F940 1 Japan Mitsubishi 10 years 2 PLC FXIN-60 1 Japan Mitsubishi 10 years 3 Solenoid Valve SY3120 41 Japan SMC 10 years 4 Manifold VQC3 2 Japan SMC 10 years 5 Design pressure valve IR3000 1 Japan SMC 10000 Kilometers 6 Oil filter combinations AL3000 1 Japan SMC 5 years (need replace 7 Pressure Gauge GIN99 1 Japan SMC the fliter)

Note: Above components lifetime just for reference, the actual use may different from this, for example: The SMC can use 10000 kilometer tested in pure gas source environment. Chapter 3: The Fixture Figure for WEWON-8330A-2

01.Each test head pole can be fixed one, if need, also can be fixed 2-3. If necessary (such as navigation buttons, volume control keys, etc.) can be assember one test head on side.

02. Pressure test: calibrator should be placed on the table, the probe fastened to the ploe and vertical to the calibrator, turn the power on, and set it zero, then the machine powered on, enter the [Test Interface] Click [stop pressure ], after the key switch to [pressure test] cylinder extend to the plate dynamometer, dynamometer shows the current pressure, if stress is too excessive the current key strike force, precision rotating counterclockwise regulator can reduce stress, or booster)

Chapter 4: The Control Panel for WEWON-8330A-2

From left to right are: 1、 power switch: pull to the right, power, on, pull to the left to turn off the machine power; 2, the pressure test emergency stop switch: When accur emergency situation press this switch to stop running clockwise rotate the swith recover running; 3、Mitsubishi LCD touch screen: for test setup and control;

Chapter 5: After-Sale Service Description :

01. Warranty free in 2 years, during warranty have four times free maintenance services. 02. Offering the temperature nine point testing and giving third-party verification report measure CNSA 03. After the new machine to the factory, to provide equipment installation and training, other non-pipe equipment and route should constructed cooperated with your factory. Note: The following are out of warranty and maintenance scope 01. Improper use or operation fault in machine damaged. Self-moving modification and improper maintenance. 02. Due to natural disasters and other harsh environment caused unpredictable damage or malfunction. 03. After the warranty period, the customer can renew the maintenance contract with the company, paid us and continue to enjoy our services.

Chapter 6: The Machine Specifications for WEWON-8330A-2

01. Phone Number can be tested simultaneously: 2 pcs (required before ordering) 02. Measuring number of head: 12 pcs (each group has 6 pieces or assigned advanced) 03. Probe pressure: 200~500gf or 450~1000gf 04. Cylinder stroke: 0~10mm 05. Test rate: 10~60 times/min can be adjustment 06. Count Set: 0~999999 can be adjustment 07. Volume: W700*D390*H530mm（3 station） 08. Weight: 25kg 09. Pressure: ≧ 0.5MPa 10. Power: 1∮ ,AC220V, 5A

Chapter 7: The Product Usage Description

The machine is suitable life testing resistance of mobile phones, PDA, computer, CD/MP3, electronic dictionaries, appliances, remote control cars and other types of rubber, metal shrapnel hit the button.

Quality assurance: In order to further improve the company’s product and company management level, to provide users with high brand, high quality, high efficiency, world-class high-service environmental testing equipment, the company strictly in accordance with IS09001: 2008 version of the standard quality assurance system operation.