Part Numbers & Description

MODEL#: NA8000XXX

CUSTOMER SERVICE: 1-800-527-7510 PARTS LIST Part Numbers & Description 1. 2 blue players assembly 1 2. 3 blue players assembly 2 3. 5 blue players assembly 1 4. 2 red players assembly 1 5. 3 red players assembly 2 6. 5 red players assembly 1 7. Side panel 2 8. End panel 2 9. Playfield 1 10.Leg 4 11. Handle 8 12.Rod end cap 8 13.Ball entry cup 2 14.Slider scorer 2 15.Playfield support rod (1/4”x29-1/4”) 3 16.Floor leveler 4

Hardware Numbers & description 17.Hex bolt (3/8”x5-1/4”) 16 18.Hex nut for 3/8” bolt 16 19.Acorn nut for support rod 6 20.Washer 50mmdia for 3/8” bolt 16 21.Washer 24mmdia for 3/8” bolt 16 22.Washer 15mmdia for 1/4” bolt 14 23.Flat head Philips screw 4x30mmL 8 24.Flat head Philips screw 4x15mmL 14 25.Rubber bumper 16 26.Plastic washer 32 27.Allen bolt (1/4”x2”) 8 28.Allen bolt (3/16”x5/8”) 8 29.Wrench 1 30.Allen wrench 1

2 OVERVIEW DRAWING

3 HARDWARE LIST

17. Carriage bolt – 16pcs 28. Allen bolt – 8pcs

27. Allen bolt – 8pcs 23. Flat head Philips screw 24. Flat head Philips screw 4x30mmL – 8pcs 4x15mmL – 14pcs

19. Acorn nut – 6pcs

25. Rubber bumper 16pcs

21. Washer 24mmdia – 16pcs 20. Washer 50mmdia – 16pcs

22. Washer 15mmdia – 14pcs

18. Hex nut for 3/8” bolt 16pcs 26. Plastic washer 32pcs ATTACHMENT

30. Allen Wrench - 1pc Soccer ball – 4pcs

29. Wrench - 1pc

4 ASSEMBLY STEPS

STEP 1 Place side panels (7) upside down as shown. The round ball entry hole will be closest to the floor. Slide 2 Plastic washers (26) and 1 Rubber bumper (25) over each end of player rods. To ease assembly, push the bushings on the rods up against the men. Align the rods as shown. The handle end of the rod has a hole close to the end of the rod.

Note: You are working upside down. All of the home team must face one direction and the away team the other. All home team handles will go on one side, all the away team on the other. The handle end of the rod has the extra hole close to the end of the rod.

STEP 2 Insert the rods through the rod bushings in one side panel. Once you are sure the player rods are correct, slide the other side panel onto the rods.

5 STEP 3 Place the playfield (9) in between the side panels (7) with graphics facing down. Make sure that the Playfield fit into the groove on the side panels (7). Slide the playfield support rods (15) through the two side panels (7). Secure it with 6 washers for 1/4” bolt (22) and 6 Acorn nut for 1/4” bolt (19). Do not tighten at this time.

#19--6pcs #22–6pcs #27--6pcs STEP 4 Attach the two end panels (8) to the side panels (7) using 8 Allen bolts (1/4”x2”) (27) and 8 washers for 1/4” bolt (22). The groove must face inward toward the playfield. Tighten all the hardware used. Attach playfield (9) to end panels (8) with 8 flat head Philips screws (23).

#27--8pcs

#22--8pcs #23-8pcs

6 STEP 5 Install legs (10) with 4 Carriage bolts (17), 4 50mmdia washers (20), 4 24mmdia washers (21) and 4 Hex nuts (18) per leg. Tighten all 16 bolts and washers used in this step at this time. Screw one Floor leveler (16) into the bottom of each leg (10).

#17--16pcs

#21--16pcs #18--16pcs

#20--16pcs

STEP 6 IMPORTANT: TWO ADULTS NEEDED IN THIS STEP

Very carefully turn the table over and set on its legs. Be careful! The table is very heavy and the rods will slide. Do not lift the table by holding onto the rods.

STEP 7

Attach 2 ball entry cups (13) to side panels (7), using 6 Flat head Philips screws (24).

7 #24--6pcs STEP 8 Attach the two sets of slide scorers (14) to the top side of end panels (8) using 4 flat head Philips screws (24) for each.

#24--8pcs

STEP 9 Slide the handles (11) onto the ends of the rods with the hole close to the end. Align the hole in the handle with the hole in the rod and secure it with an Allen bolt (28) for each. Install the Rod end cap (12) onto the other end of the rod.

#28--8pcs

9 IMPORTANT

When the table is in the upright position, the goalie rod should always be in your left hand regardless of which side of the table you are standing on.

Make sure the rods are installed correctly before attaching the handles.

If the rods do not slide freely through the bushings, you can apply spray wax (furniture polish) to a cloth and wipe down the rods to make them slide easier.

If spray wax does not help, the table may not be square. Loosen the hardware on the side panels and legs to re-align the table. Tighten hardware when complete.

Should the playfield have a bow in it, you can loosen the playfield support rods to relax the playfield.

SPORT SUPPLY GROUP INC. 092003 PRINTED IN CHINA