1

Research for the torch (second IA) (secondary research)

How Light Bulbs Work – Lighting up Our Lives

The Power Okay. Light bulbs (known as incandescent) are really quite simple, and simply brilliant. The bulb has two metal contacts at the bottom of the base where they get their power from. These touch the electrical circuit in the fitting attached to your mains electricity, or any number of batteries, if we’re talking flashlights. The electrical charge used to light the bulb travels through it from one contact to the other in a loop. After hitting one contact the current goes up a wire to a filament, which is held on a supporting glass mount in the bulbs’ centre, then travels across it, down another wire identical to the first, and on to the other contact. A Fundamental Filament This filament is central in importance to the light bulb as well as central in position. It is made out of tungsten, which is a metal with an extremely high melting point, and it certainly needs one. After the light bulb is switched on, the tungsten filament is heated to between an incredible 2,200 and 2,500 degrees Centigrade! As well as its’ own properties, to further stop it burning up; the glass bulb does not contain any oxygen, but instead holds an inert gas called argon or a mixture of argon and nitrogen for all regular bulbs or krypton/xenon instead of the argon for more expensive premium models. (What about halogen bulbs? We’ll get to them later). The filament is also tremendously long and thin. For example; in a standard 60 watt bulb the tungsten wire is over six feet long, but at the same time, it is less than one-hundredth of an inch in diameter. So how does it fit into such a tiny space? It’s double coiled, that’s how. Wound up tight to produce a first coil, then this coil is re-wound again to make the smaller than an inch filament that can be seen inside the bulb. Good Vibrations So the electrical charge heats up the filament to produce the light. How? The electrons that make up the electricity current rocket along, slamming into the tungsten atoms and causing them to vibrate. This friction produces heat or thermal energy, which is captured and then released by the electrons in the form of photons (light). Most of these are unfortunately in the lower end of the spectrum (known as infrared) and are invisible to humans. But the hotter the filament, the higher wavelength visible photons are emitted which we can see, and the brighter the light from the bulb. Size Matters Higher wattage bulbs have longer filaments, so they produce more light from having more atoms to vibrate, and conversely, low voltage light bulbs have shorter coils so the light is dimmer. In a three-way light bulb, there are two filaments present with one being larger than the other. When the setting is on low, then only the small filament is used, so the light is dim. If

Krish Suchak 11.3 2 the setting is put to medium, then only the larger filament has current travelling through it, and the smaller one is cut off from the flow. When the setting is on high; both filaments are in use together and the light is therefore very bright. To control this there are three connections (for the three operating modes). One each for both filaments exclusive use, and a third to be shared. A complicated switch controls the delivery of current. Nothing Lasts Forever So the tungsten filament is under tremendous strain, and won’t last. As the bulb is used for more and more hours the vibration and white-hot temperatures begin to take their toll. Increasingly the atoms from the coil will shake so much they will start to lose contact with each other and begin splitting away from their brethren. In old vacuum light bulbs, they would shoot off into the space inside the bulb until they hit the glass. But with the argon or krypton inside them, modern bulbs last longer as many tungsten atoms hit the gas atoms and bounce around randomly, hopefully to reattach themselves to the filament if they get near enough to do so. Krypton atoms have more mass than those of argon and get more hits, but krypton is much rarer, so you have to pay for the benefit. Though these light bulbs last longer, sooner or later the filament begins to disintegrate as the tell-tale darkening of the glass bulb increases (being caused by the errant tungsten) and your bulb will blow. Often it might make the sound, ‘plink’, a few times and start flickering first, only to settle down again as if teasing you, so you decide not to change it after all and put the replacement you’ve just rummaged around for back again. Until next time you turn the lights on, that is, when it decides to give out after all. Despite your suspicions to the contrary, however, the bulb is not getting its’ revenge on you for using it when not absolutely needed, or acting out of spite against humanity in general. It really can’t help it. A weak old bulb is at correct operating temperature when turned on for a while, but can’t reach it uniformly all the way along the filament when first switched on. There is always a surge of electricity drawn by a light bulb being turned on because of there being less electrical resistance in the tungsten when it is cooler. This resistance increases as the bulb heats up, but the weak spots in the filament heat up quicker than the rest (they have less surface area due to the evaporated tungsten atoms) and the funnelling effect will cause these weaker areas to melt or snap due to the increased vibration. So most light bulbs may not last that long, but they are relatively cheap and very plentiful. Hello to Halogen A halogen bulb works differently. It still has the same tungsten filament inside it as do the others, but here chemistry is employed in addition to physics to prolong its’ working life. Inside these light bulbs, there is a halogen gas (almost always iodine) present, mixed in with the argon or krypton. This new gas reacts with the vaporized tungsten that collects on the glass to form chemical compounds called metal halides. These then leave the inner surface of the bulb in a constant recycling process and return to near the filament where the increased heat breaks down the halide into its constituent parts. The tungsten molecules

Krish Suchak 11.3 3 are now given to return to the filament, and the iodine molecules are free again to join up with any more ejected tungsten. This is known as the halogen cycle. The reaction only works successfully on the glass itself though, rather than the bulb’s inner space, once the tungsten has condensed and will not take place if the glass is not hot enough. Therefore halogen light bulbs have to be smaller (which increases the heat); handmade of a special higher-grade glass known as ‘hard glass’ or of quartz to allow them not to break at this extra high temperature. Halogen bulbs cost more, but may have a lifetime of up to triple a normal light bulb of the same wattage, and at the same time be anything up to a fifth more efficient at producing light. Long Lifers and Energy Misers Long life light bulbs certainly last a very long time, so it might be argued that halogen is a waste of money. This is absolutely not true. A lot of these ‘long lifers’ are actually quite inefficient. To burn longer they burn cooler, and at lower temperatures; a smaller percentage of energy is given off as light rather than wasted heat by the tungsten. All light bulbs waste energy by giving off infrared light so the ‘energy misers’ out there on the shelves waiting for your basket to pass by may be considered a worthwhile option. But don’t be too hasty in gathering them up either. For some of these are not as good value as the cheap and cheerful regular guys. It might be claimed that a 55 watt can replace a 60, or a 90 will do for a 100 watt, but this is not necessarily so. Many (not all) of these ‘misers’ are more mean and miserly with light than with energy, and although it may not be noticed, sometimes produce less light by such a percentage factor that actually causes them to use more watts of power for a given unit of light if you chase this down the comparison scale. Light Bulbs Rule OK? So that is how they work. Not encyclopedic maybe, but a brief tour of a subject that matters to all; the incandescent electric light bulb. Still going strong after more than 120 years. Fluorescent lighting and LED‘s (Light Emitting Diodes) with their ‘cold light’ technology may be pushing more and more at the margins of their rule, but traditional light bulbs are still kings in our culture today. How they work A flashlight (usually called a torch outside North America) is a hand-held electric-powered light source. Usually the light source is a small incandescent light bulb or light-emitting diode (LED). Typical flashlight designs consist of the light source mounted in a parabolic or other shaped reflector, a transparent lens to protect the light source from damage and debris, a power source (typically electric batteries), and an electric power switch. While most flashlights are hand-held, there are head or helmet-mounted flashlights designed for miners and campers and battery-powered lights for bicycles. Some flashlights are powered by hand-cranked dynamos or electromagnetic induction or are recharged by solar power. The name flashlight is used mainly in the United States and Canada. In other English- speaking countries, the more common term is torch or electric torch.

Krish Suchak 11.3 4

The circuit

Have you ever taken an electric torch to pieces to find out how it works? Look at the diagram below which shows the arrangement of parts inside one kind of torch:

Structure of an electric torch Why did the designer choose this particular combination of materials? The metal parts of the torch must conduct electric current if the torch is to function, but they must also be able to stand up to physical forces. The spring holding the cells in place should stay springy, while the parts of the switch must make good electrical contact and be undamaged by repeated use. The lamp and reflector make up an optical system, often intended to focus the light into a narrow beam. The plastic casing is an electrical insulator. Its shape and colour are important in making the torch attractive and easy to handle and use. A torch is a simple product, but a lot of thought is needed to make sure that it will work well. Can you think of other things which the designer should consider? A different way of describing the torch is by using a circuit diagram in which the parts of the torch are represented by symbols:

Krish Suchak 11.3 5

Circuit diagram of an electric torch There are two electric cells ('batteries'), a switch and a lamp (the torch bulb). The lines in the diagram represent the metal conductors which connect the system together. A circuit is a closed conducting path. In the torch, closing the switch completes the circuit and allows current to flow. Torches sometimes fail when the metal parts of the switch do no make proper contact, or when the lamp filament is 'blown'. In either case, the circuit is incomplete. . Current An electric current is a flow of charged particles. Inside a copper wire, current is carried by small negatively-charged particles, called electrons. The electrons drift in random directions until a current starts to flow. When this happens, electrons start to move in the same direction. The size of the current depends on the number of electrons passing per second. Current is represented by the symbol I, and is measured in amperes, or 'amps', A. One ampere is a flow of 6.24 x 1018 electrons per second past any point in a wire. That's more than six million million million electrons passing per second. This is a lot of electrons, but electrons are very small and each carries a very tiny charge. In electronic circuits, currents are most often measured in milliamps, mA, that is, thousandths of an amp.

.

Voltage In the torch circuit, what causes the current to flow? The answer is that the cells provide a 'push' which makes the current flow round the circuit. When the cells are new, enough current flows to light the lamp brightly. On the other hand, if the cells have been used for some time, they may be 'flat' and the lamp glows dimly or not at all. Each cell provides a push, called its potential difference, or voltage. This is represented by the symbol V , and is measured in volts, V. Typically, each cell provides 1.5 V. Two cells connected one after another, in series, provide 3 V, while three cells would provide 4.5 V:

Krish Suchak 11.3 6

Cells connected in series Which arrangement would make the lamp glow most brightly? Lamps are designed to work with a particular voltage, but, other things being equal, the bigger the voltage, the brighter the lamp. Strictly speaking, a battery consists of two or more cells. These can be connected in series, as is usual in a torch circuit, but it is also possible to connect the cells in parallel, like this:

Cells connected in parallel A single cell can provide a little current for a long time, or a big current for a short time. Connecting the cells in series increases the voltage, but does not affect the useful life of the cells. On the other hand, if the cells are connected in parallel, the voltage stays at 1.5 V, but the life of the battery is doubled. A torch lamp which uses 300 mA from C-size alkaline cells should operate for more than 20 hours before the cells are exhausted.

Which way does the current flow? One terminal of a cell or battery is positive, while the other is negative. It is convenient to think of current as flowing from positive to negative. This is called conventional current. Current arrows in circuit diagrams always point in the conventional direction. However, you should be aware that this is the direction of flow for a positively-charged particle. In a copper wire, the charge carriers are electrons. Electrons are negatively-charged and therefore flow from negative to positive. This means that electron flow is opposite in direction to conventional current. Current flow in electronic systems often involves charge carriers of both types. For example, in transistors, current can be carried by electrons and also by holes, which behave as positive charge carriers.

Krish Suchak 11.3 7

When the behaviour of a circuit is analysed, what matters is the amount of charge which is being transferred. The effect of the current can be accurately predicted without knowing about whether the charge carriers are positively or negatively charged. A cell provides a steady voltage, so that current flow is always in the same direction. This is called direct current, or d.c. In contrast, the domestic mains provide a constantly changing voltage which reverses in polarity 50 times every second. This gives rise to alternating current, or a.c., in which the charge carriers move backwards and forwards in the circuit.

The Structure of an Electric Torch Light An electric torch light is an essential tool to man, and it can be found in almost every household and workplace in this planet. This article tries to give a basic overview of the structure of an all important electric torch light. A basic Electric Torch Light generally consists of several components: Bulb - The main component that gives the light. The two most common types of bulb are Incandescent and Light-Emitting Diode (LED) bulbs. For most torch lights, the bulb is of incandescent type, where a tungsten filament is enclosed within a glass envelope filled with inert gases like halogen or xenon. Light-Emitting Diode (LED) bulbs are made of semiconductor substrates coated with phosphors, and are used because of their lower power consumption and very long lifespan. Reflector - A conical shaped piece of plastic or aluminium which is placed over the bulb in the torch light. The reflector is normally coated with a highly reflective coating, and the purpose of it is to direct the surrounding light emitted by the bulb forward. Depending on the texture of the coating, the light beam quality may differ from a high intensity beam to a wide area type of light. Lens - The optics placed in front of the bulb. The lens, which can be made from clear plastics or glass, is used mainly to protect the reflector and the bulb, and yet allow light to pass through. Glass are less susceptible to scratches, thus are preferred over the plastic counterpart. Switch Mechanism - The control component of the torch light. A switch allows the user to turn on the torch light only when necessary, thus conserving electric energy. Some torch lights uses complex electronic circuitry within the switch, and allow special functions such as dimming and strobing to be achieved. Battery - Power source for the Electric Torch Light. The batteries required for the torch light depends on the bulb being used, and they come in various sizes, from AAA to D sized. Alkaline batteries are still widely used, but Lithium ones are picking up due to their highest capacity and smaller size. Body - Normally made of aluminium or durable plastics, the torch light body is used to hold all the other components in place. Several shape of the body is available in the market, and the most common ones are those in a "tube" form, which allows user to hold and operate the torch with just one hand. With advancing technologies, the electric Torch Light is slowly evolving from a simple handheld equipment into a complex piece of art. To know more, look out for my future articles on torch lights!

Krish Suchak 11.3 8

How a Basic Fluorescent Lamp Works General Design The general design of a simple fluorescent lamp consists of a sealed glass tube. The tube contains a small bit of mercury and a gas (usually argon) kept under very low pressure. The tube also contains a phosphor powder, coated along the inside of the glass. The tube has two electrodes, one at each end, which are wired to an electrical circuit. The electrical circuit, which includes a starter and ballast, is hooked up to an alternating current (AC) supply.

General Operation: When the lamp is first turned on, the current travels through the path of least resistance, which is through the bypass circuit, and across the starter switch. This current then passes through the circuit heating up the filament in each electrode, which are located at both ends of the tube (these electrodes are simple filaments, like those found in incandescent light bulbs). This boils off electrons from the metal surface, sending them into the gas tube, ionizing the gas. The mercury vapor becomes "excited" and it generates radiant energy, mainly in the ultraviolet range. This energy causes the phosphor coating on the inside of the tube to fluoresce, converting the ultraviolet into visible light.

The Starter: The starter is basically a time delay switch. Its job is to let the current flow through to the electrodes at each end of the tube, causing the filaments to heat up and create a cloud of electrons inside the tube. The starter then opens after a second or two. The voltage across the tube allows a stream of electrons to flow across the tube and ionize the mercury vapour. Without the starter, a steady stream of electrons is never created between the two filaments, and the lamp flickers.

Krish Suchak 11.3 9

The Ballast: The ballast works mainly as a regulator. They consume, transform, and control electrical power for various types of electric-discharge lamps, providing the necessary circuit conditions for starting and operating them. In a fluorescent lamp, the voltage must be regulated because the current in the gas discharge causes resistance to decrease in the tube. The AC voltage will cause the current to climb on its own. If this current isn’t controlled, it can cause the blow out of various components.

Newer Designs: Today, the most popular fluorescent lamp design is the “rapid start” lamp. This design works the same as the basic design described above, but it doesn't have a starter switch. Instead, the lamp's ballast constantly channels current through both electrodes. This current flow is configured so that there is a charge difference between the two electrodes, establishing a voltage across the tube.

Another method used in instant-start fluorescent lamps, is to apply a very high initial voltage to the electrodes. This high voltage creates a corona discharge, which causes an excess of electrons on the electrode surface that forces some electrons into the gas. These free electrons ionize the gas, and almost instantly the voltage difference between the electrodes establishes an electrical arc.

In Conclusion: There are many different types of fluorescent lamps but they all work in the same basic way: An electric current stimulates mercury atoms, which causes them to release ultraviolet photons. These photons in turn stimulate a phosphor, which emits visible light photons

Krish Suchak 11.3