DOCSLIB.ORG

Op-Amp and Comparators Selection Guide

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Op-Amp and Comparators Selection Guide Op-Amp and Comparators Selection Guide June 2019 Tom Kawano ([email protected]) Peter Hartshorn ([email protected]) NJR Corporation Contents Contents Product Topics High Efficiency Series Evaluation Boards Product-Tree Cross Reference Precision Rail-to-Rail ASSP High Speed Low Noise Audio Specialized Op-Amps High EMI Immunity 5V, CMOS Power Line Communication High Output Current Small Packages Current Detection Low Power 14V to 36V CMOS Low Noise Audio Comparators Renewal Standard Series 2 Product Topics High Efficiency Op-Amps -NJU775xx Series- Contents Low Power General-Purpose High Speed (GBW < 1MHz) (GBW 1MHz to 10MHz) (GBW > 10MHz) Battery-powered instruments, Industrial equipment, Ultrasonic/photoelectric sensors, pressure/gas sensors & fire alarms automotive accessories, motor controllers current detectors & audio & measuring instruments U.D. High NJU7758x NJU7047 1.8mA, 20MHz 1.8mA, 20MHz NJU7043 NJM8532 800µA, 0.8MHz Current 290µA, 1MHz M.P. NJU7755x Supply Supply PLAN 50µA, 1.7MHz FEATURES NJU7754x •Low power •High EMI immunity 10µA, 0.3MHz •Operating at 125°C Low Narrow Gain Bandwidth Product (GBW) Wide 3 Product Topics Features of NJU775xx Series Contents High Efficiency Overvoltage Protection High EMI Immunity Low power and wide GBW Protects Op-amps from excessive input Tolerance to RF noise V+=0V Efficiency = GBW Input tolerant Isupply OK EMIRR= 90dB (f= 1.8GHz) Supply current 7V max. 70dB (f= 800MHz) Conventional products 330μA 120 NJU7755x 50μA BLOCK DIAGRAM COMPARISON 100 V+ Isupply [μA/ch] 80 +INPUT 60 85% less supply current OUTPUT -INPUT 40 EMIRR [dB] 20 ESD protection V- 0 Gain bandwidth product High efficiency series 1M 10M 100M 1G Conventional + Frequency [Hz] products 1.2MHz V NJU7755x 1.7MHz +INPUT OUTPUT -INPUT 20dB (f= 800MHz) GBW [MHz] 1.4 times wider GBW V- EMIRR= 32dB (f= 1.8GHz) Standard op-amp 4 : U.D. Precision Op-Amps : M.P. Contents 5V SUPPLY 36V SUPPLY Low Power Low Noise 20V/μs High Speed 150µV, 1µV/°C max. 150µV, 5µV/°C max. 800µV, 9µV/°C max. 400µV, 5µV/°C max. NJU77600 [1ch] NJU7076 [1ch] NJM8512A [2ch] NJM8512B [2ch] NJU77602 [2ch] NJU7077 [2ch] NJM8513A [4ch] NJM8513B [4ch] NJU77604 [4ch] NJU7078 [4ch] Isupply=20μA/ch en=10nV/√Hz Single Supply R-R I/O R-R Output R-R Output 800µV, 1µV/°C typ. 450µV, 4µV/°C typ. NJM8208Z [2ch] NJM2119 [2ch] Zero-Drift 15µV, 0.05µV/°C max. Low Noise NJU7098A [1ch] 50µV, 0.6µV/°C max. 60µV, 1.2µV/°C max. R-R Output NJMOP277 [1ch] NJMOP177 [1ch] NJMOP2277 [2ch] NJMOP1772 [2ch] 5 Precision Op-Amps Back to Category Contents CharacteristicsCharacteristics Supply ISUPPLY VIO VIO VIO Common-Mode -Vsat +Vsat Voltage Package / Pin Rail o - + - - Voltage (25 C) (All Temp.) Input Voltage Range Noise (per Ch.) Drift IB VOL-V V -VOH CMR SR fT *2 *1 23 to - - + - EMI V - V typ. max. max. max. typ. min. max. max. max. typ. typ. typ. typ. DFN DMP SSOP SPICE SOP Immunity SC88A SOT Rail Product Name Ch. V mA µV µV µV/oC nA V V V V dB V/µs MHz nV/ÖHz MSOP Model Notes NJMOP177G 1 6 to 36 1.6 60 100 1.2 1.2 (V-) +2 (V+) -2 3 3 140 0.3 1.1 8 8 NJMOP1772 2 6 to 36 1.3 60 100 1.2 1.2 (V-) +2 (V+) -2 3 3 135 0.3 1.1 8 8 NJMOP277G Yes 1 4.5 to 36 0.76 50 100 0.6 0.5 (V-) +2 (V+) -2 1.5 1.5 140 0.7 1 8 8 8 NJMOP2277G Yes 2 4.5 to 36 0.76 50 100 0.6 0.5 (V-) +2 (V+) -2 1.5 1.5 140 0.7 1 8 8 8 NJMOP277F Yes 1 Characteristcs4.5 to 36 0.76 20 50 0.15 0.5 (V-) +2 (V+) -2 1.5 1.5 140 0.7 1 8 8 8 NJMOP2277F Yes 2 4.5 to 36 0.76 20 50 0.15 0.5 (V-) +2 (V+) -2 1.5 1.5 140 0.7 1 8 8 NJM8208Z Out Yes 2 3 to 35 1 800 1 - 55 (V-) (V+) -1 0.15 0.15 100 0.2 0.35 - 8 8 NJM8512A Yes 2 9 to 32 1.3 800 1400 9 0.025 (V-) +2.5 (V+) -2.5 1.2 1.5 108 20 7 10 8 8 NJM8512B Yes 2 9 to 32 1.3 400 700 5 0.025 (V-) +2.5 (V+) -2.5 1.2 1.5 108 20 7 10 8 8 NJM8513A Yes 4 9 to 32 1.3 800 1400 9 0.025 (V-) +2.5 (V+) -2.5 1.2 1.5 108 20 7 10 14 NJM8513B Yes 4 9 to 32 1.3 400 700 5 0.025 (V-) +2.5 (V+) -2.5 1.2 1.5 108 20 7 10 14 NJU7076 Out Yes 1 2.2 to 5.5 0.6 150 400 5 0.001 (V-) (V+) -1 0.15 0.15 90 0.5 1.3 10 5 NJU7076B Out Yes 1 2.2 to 5.5 0.6 300 400 5 0.001 (V-) (V+) -1 0.15 0.15 90 0.5 1.3 10 5 NJU7077 Out Yes 2 2.2 to 5.5 0.6 150 400 5 0.001 (V-) (V+) -1 0.15 0.15 90 0.5 1.3 10 8 NJU7078 Out Yes 4 2.2 to 5.5 0.575 200 400 5 0.001 (V-) (V+) -1 0.15 0.15 90 0.5 1.3 10 14 NJU7098A Out Yes 1 3 to 10 0.6 15 15 0.05 0.02 (V-) (V+) -1.5 0.01 0.15 130 3 3 120 6 NJU77600 I/O Yes 1 2.3 to 5.5 12 150 400 1 0.001 (V-) (V+) 0.15 0.15 - 0.04 0.08 - 5 5 6 NJU77602 I/O Yes 2 2.3 to 5.5 12 150 400 1 0.001 (V-) (V+) 0.15 0.15 - 0.04 0.08 - 8 8 8 NJU77604 I/O Yes 4 2.3 to 5.5 12 200 400 1 0.001 (V-) (V+) 0.15 0.15 - 0.04 0.08 - 14 *1 SOP8: JEDEC 150mil *2 MSOP8 (VSP8): meet JEDEC MO-187-DA,thin type 6 : U.D. : Rail-to-rail output High Speed Op-Amps : M.P. : Rail-to-rail I/O Contents Slew Rate [V/µs] 260V/µs, 1GHz OVER 100 NJM2711 [1ch] NJM2712 [2ch] V+/V-=±2V to ±4.5V 100 2.5nV/√Hz 60V/µs, 90MHz Transceiver NJM2719 [2ch] 45V/µs, 200MHz 40V/µs, 20MHz V+/V-=±2.25V to ±5V NJM2136 [1ch] NJM2716 [1ch] 35V/µs, 34MHz 40 NJM2137 [2ch] NJM2717 [2ch] NJU77701 [1ch] V+/V-=±1.35V to ±6V + V =2.7V to 12V V+=2.4V to 5.5V Isupply=0.57mA/ch Air conditioner 13V/µs, 3.5MHz NJM072C/CA Automotive NJM074C/CA 10V/µs, 4MHz 9V/µs, 5MHz 10V/µs, 20MHz NJM3472 [2ch] NJU7046 [1ch] 8.5V/µs, 3MHz NJU7758x [1/2ch] 10 NJM3474 [4ch] NJU7047 [2ch] + Photoelectric sensor NJM842 [2ch] + V =2.4V to 5.5V V =3V to 36V NJU7048 [4ch] NJM844 [4ch] V+=2.7V to 5.5V V+=3V to 36V 4 10 40 100 GBW [MHz] 7 High Speed Op-Amps Back to Category Contents Characteristics Supply ISUPPLY Common-Mode -Vsat +Vsat Voltage Package / Pin Rail - + *3 - - Voltage Input Voltage Range Noise (per Ch.) SR GBW fT VOL-V V -VOH RL Io VIO Topr *2 *1 23 to - - + - EMI V - V typ. typ. typ. typ. min. max. max. max. typ. typ. max. DFN DMP SSOP SOP SPICE Immunity SC88A SOT Rail o MSOP Product Name Ch. V mA V/µs MHz MHz V V V V Ω mA nV/ÖHz mV C Model Notes NJM072C/A 2 8 to 36 1.4 13 3.5 3 (V-) +4 (V+) -4 3 3 10k 50 15 10/6 -40 to 85 8 8 NJM074C/A 4 8 to 36 1.4 13 3.5 3 (V-) +4 (V+) -4 3 3 10k 50 15 10/6 -40 to 85 14 14 NJM2136 1 2.7 to 12 0.63 45 200 40 (V-) +1.3 (V+) -1.3 1.6 1.4 1k 3 - 5 -40 to 85 8 8 NJM2137 2 2.7 to 12 0.57 45 200 40 (V-) +1.3 (V+) -1.3 1.6 1.4 1k 3 - 5 -40 to 85 8 8 NJM2711 1 4 to 9 1.9 260 1000 180 (V-) +1.2 (V+) -1.2 1.3 1.3 1k 23 6.8 7 -40 to 85 5 NJM2712 2 4 to 9 1.9 260 1000 180 (V-) +1.2 (V+) -1.2 1.3 1.3 1k 23 6.8 7 -40 to 85 8 8 NJM2716 Out 1 2.7 to 12 4.2 40 25 30 (V-) (V+) -1.2 0.5 0.5 4k 2.5 40 10 -40 to 85 5 NJM2717 Out 2 2.7 to 12 4 40 25 20 (V-) (V+) -1.2 0.5 0.5 4k 2.5 40 11 -40 to 85 8 8 8 NJM2719 Out 2 4.5 to11 7 60 90 100 (V-) +0.5 (V+) -1.3 0.3 0.4 1k 18 2.5 9 -40 to 85 8 8 NJM3472 Yes 2 3 to36 1.75 10 4 4 (V-) (V+) -2.0 0.3 1.3 2k 30 - 10 -40 to 125 8 8 8 NJM3474 Yes 4 3 to 36 1.75 10 4 4 (V-) (V+) -2.0 0.3 1.3 2k 30 - 10 -40 to 125 14 14 NJM842 Yes 2 3 to36 1.75 8.5 3 3 (V-) (V+) -1.8 0.01 1.3 2k 30 - 5 -40 to 125 8 8 8 NJM844 Yes 4 3 to 36 1.75 8.5 3 3 (V-) (V+) -1.8 0.01 1.3 2k 30 - 5 -40 to 125 14 14 NJU7046 I/O Yes 1 2.7 to 5.5 1.4 9 5 5 (V-) (V+) 0.1 0.1 2k 100 25 5 -40 to 125 5 5 NJU7047 I/O Yes 2 2.7 to 5.5 1.35 9 5 5 (V-) (V+) 0.1 0.1 2k 100 25 5 -40 to 125 8 8 8 NJU7048 I/O Yes 4 2.7 to 5.5 1.325 9 5 5 (V-) (V+) 0.1 0.1 2k 100 25 5 -40 to 125 14 14 NJU7758x I/O Yes 1/2 2.4 to 5.5 1.8 10 20 - (V-) -0.2 (V+) +0.2 0.025 0.025 - - 8 4 -55 to 125 8 8 8 5 Stable Gain - + NJU77701 I/O Yes 1 2.4 to 5.5 3.8 35 34 25 (V ) (V ) 0.08 0.1 600 110 6 1.5 -40 to 125 5 ≥ 14dB *1 SOP8: JEDEC 150mil *2 MSOP8 (VSP8): meet JEDEC MO-187-DA,thin type 8 *3 Short circuit Voltage Noise ≤ 15nV/√Hz : U.D.
Load more

Recommended publications
  • OPEX-1: a High Performance Class a Opamp for Audio
    2013 OPEX-1: a High Performance Class A Opamp for Audio A low component count Lin topology VFA opamp for audio applications, featuring a matched pair JFET input stage, class A output stage and Two Pole Compensation (TPC). This design features very low distortion: 10V peak into a 600 Ω load is below 1 ppm. The OL UGF is 13 MHz, and the slew rate in excess of 100 V/us. Other than the LSK389C matched JFET pair, the OPEX-1 uses readily available components, and fits on a 6 cm x 4 cm DSTHP PCB. The construction cost for 4-6 pcs is $15 each Andrew C. Russell 9/1/2013 A High Performance Discrete Opamp for Audio Applications OPEX-1: a High Performance Discrete Opamp for Audio Applications. Sometime around 2009 or 2010, I took an LM4562 and biased into class A, then added a discrete class A buffer stage inside the global feedback loop to produce a high performance class A buffer– you can read about it here, and look at the distortion results in Fig.1 below. In the write up, I focused on the fact that IC opamps always feature class AB output stages, and we know that when driving a heavy load (so, 600 Ω or so in the context of this discussion), they will transition into class B, and the result will be harmonics both in the output signal, and on the supply rails. My effort allowed me to swing a 600 Ω load 20V pk-pk at about 2ppm at 20 kHz, and at 2 or 3 V pk-pk, distortion was about 1.5~2ppm - this measurement result in actuality limited by the performance of the AP Sys272 which has a distortion floor of -114 dB ref 1V into 600 Ω (See Fig 1).
    [Show full text]
  • Designer's Master Selection Guide
    Selection Guide EIGHTH EDITION Analog/Mixed-Signal Products Designer’s Master Selection Guide August 2002 © 1996, 1997, 1999, 2000, 2001, 2002 Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
    [Show full text]
  • Headphone Amplifier for Guitar
    Daniil Danilov Headphone Amplifier For Guitar Metropolia University of Applied Sciences Bachelor of Engineering Electronics Degree Programme Bachelor’s Thesis 20 April 2020 Author Daniil Danilov Title Headphone Amplifier For Guitar Number of Pages 51 pages + 1 appendices Date 20 April 2020 Degree Bachelor of Engineering Degree Programme Electronics Professional Major Instructors Matti Fischer, Senior lecturer Tommi Otsavaara, Chief Technology Officer The goal of this project was to design an audio amplifier device in the guitar pedal form factor, which will be used for demonstration purposes of the “Darkglass electronics Oy” Ex- hibitor stand on Winter NAMM 2020 convention in Anaheim, USA. The second aim was to learn and understand research, development, and production processes, how from an idea and general prerequisites create a product, which will meet those requirements, and how various nuances affect those processes and final results. The thesis consists of demonstrating device development sequence as well as device circuit analysis from simulations to board measurements. Simulations were made in LTspice soft- ware. Schematics, PCB design and production documents were created in Altium Designer software. Measurements were made using APx515 Audio Analyzer and oscilloscope. As a result, the device was made on time. It met the requirements, and the project is con- sidered as completed. The device is able to produce a maximum output power of 1 Watt, with a THD+N of 1%. Keywords Amplifier, small signals, PCB design, analog electronics,
    [Show full text]
  • Small Signal Audio Design
    Small Signal Audio Design Douglas Self AMSTERDAM BOSTON HEIDELBERG LONDON NEW YORK OXFORD PARIS SAN DIEGO SAN FRANCISCO SINGAPORE SYDNEY TOKYO Focal Press is an imprint of Elsevier Focal Press is an imprint of Elsevier The Boulevard, Langford Lane, Kidlington, Oxford, OX5 1GB, UK 30 Corporate Drive, Suite 400, Burlington, MA 01803, USA First published 2010 Copyright ª 2010 Douglas Self. Published by Elsevier Ltd. All rights reserved. The right of Douglas Self to be identified as the author of this work has been asserted in accordance with the Copyright, Designs and Patents Act 1988 No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher. Details on how to seek permission, further information about the Publisher’s permissions policies and our arrangement with organizations such as the Copyright Clearance Center and the Copyright Licensing Agency, can be found at our website: www.elsevier.com/permissions This book and the individual contributions contained in it are protected under copyright by the Publisher (other than as may be noted herein). Notices Knowledge and best practice in this field are constantly changing. As new research and experience broaden our understanding, changes in research methods, professional practices, or medical treatment may become necessary. Practitioners and researchers must always rely on their own experience and knowledge in evaluating and using any information, methods, compounds, or experiments described herein. In using such information or methods they should be mindful of their own safety and the safety of others, including parties for whom they have a professional responsibility.
    [Show full text]
  • Term Paper Rev-5 FINAL Copy Free
    An Overview of BiCMOS Analog IC Design M501 Term Paper Stephen H. Lafferty, February, 2007 Some images subject to copyright have been obscured in this copy to comply with copyright law. Contents Introduction .................................................................................................................................... 4 Strengths of Bipolar Junction Transistors (BJT’s) .......................................................................... 5 Noise ......................................................................................................................................... 5 Wideband Noise ..................................................................................................................5 Flicker (1/f) Noise ............................................................................................................... 5 Offset Voltage ........................................................................................................................... 6 Inherent Performance .......................................................................................................... 6 Floating Gate Offset Adjustment ......................................................................................... 7 Bandwidth ................................................................................................................................. 7 Summarizing the Bandwidth Comparison ........................................................................... 9 Transconductance (gm) .............................................................................................................
    [Show full text]
  • Resistor Testing for Both Excess Noise and Distortion
    RESISTOR TEST PROJECT: PART 1- TEST DESIGN Developed with support from: Audio Builders Workshop https://www.audiobuildersworkshop.com/ Rev 3.0 24-Feb-18 Test design Rev 3.0 24-Feb-18 CONTENTS Figures ........................................................................................................................................................................... 3 Summary ........................................................................................................................................................................ 4 The questions ............................................................................................................................................................ 5 Background ................................................................................................................................................................ 5 People ........................................................................................................................................................................ 5 But don’t blame them… ............................................................................................................................................. 6 Component testing ........................................................................................................................................................ 6 Fixture construction......................................................................................................................................................
    [Show full text]
  • Small Signal Audio Design
    Small Signal Audio Design This much expanded second edition of Small Signal Audio Design is the essential and unique guide to the design of high-quality analogue circuitry for preamplifiers, mixing consoles, and many other signal-processing devices. You will learn to use inexpensive and readily available parts to obtain state-of-the-art performance in all the vital parameters of noise, distortion, crosstalk, etc. This practical handbook provides an extensive repertoire of circuit blocks from which almost any type of audio system can be built. Essential points of theory that determine practical performance are lucidly and thoroughly explained, with the mathematics at an absolute minimum. Virtually every page reveals nuggets of specialized knowledge not found elsewhere. Douglas’ background in design for manufacture ensures he keeps a wary eye on the cost of things. Learn how to: • Make amplifiers with apparently impossibly low noise • Design discrete circuitry that can handle enormous signals with vanishingly low distortion • Use ordinary bipolar transistors to make amplifiers with an input impedance of more than 50 Megohms • Transform the performance of low-cost-opamps, and how to make filters with very low noise and distortion • Make incredibly accurate volume controls • Make a huge variety of audio equalisers • Make magnetic cartridge preamplifiers that have noise so low it is limited by basic physics • Sum, switch, clip, compress, and route audio signals effectively • Build reliable power-supplies, with many practical ways to keep both the noise and the cost down This much enlarged second edition is packed with new information, including completely new chapters on: • Opamps for low voltages (down to 3.3 V) • Moving-magnet inputs: archival and non-standard equalisation, for 78s etc.
    [Show full text]
  • Small Signal Audio Design
    Small Signal Audio Design Douglas Self AMSTERDAM • BOSTON • HEIDELBERG • LONDON . NEW YORK • OXFORD Focal PARIS • SAN DIEGO . SAN FRANCISCO • SINGAPORE . SYDNEY • TOKYO Press Focal Press is an imprint of Elsevier Contents Preface xiii About the Author xvii Acronyms xviii Chapter 1 The Basics 7 Signals 1 Amplifiers 2 Voltage Amplifiers 2 Transconductance Amplifiers 2 Current Amplifiers 3 Transimpedance Amplifiers 3 Negative Feedback 4 Nominal Signal Levels 5 Gain Structures 6 Amplification Then Attenuation 6 Attenuation Then Amplification 7 Raising the Input Signal to the Nominal Level 7 Active Gain Controls 8 Noise 8 Johnson Noise 9 Shot Noise 11 1//Noise (Flicker Noise) 12 Popcorn Noise 13 Summing Noise Sources 13 Noise in Amplifiers 14 Noise in Bipolar Transistors 16 Bipolar Transistor Voltage Noise 16 Bipolar Transistor Current Noise 17 Noise in JFETs 20 Noise in Op-Amps 21 Low-Noise Op-Amp Circuitry 22 Noise Measurements 23 How to Attenuate Quietly 23 Hi iv Contents How to Amplify Quietly 25 How to Invert Quietly 26 How to Balance Quietly 28 Ultra-Low-Noise Design with Multipath Amplifiers 28 Ultra-Low-Noise Voltage Buffers 29 Ultra-Low-Noise Amplifiers 30 References 32 Chapter 2 Components 33 Conductors 33 Copper and Other Conductive Elements 34 The Metallurgy of Copper 35 Gold and Its Uses 35 Cable and Wiring Resistance 36 PCB Track Resistance 37 PCB Track-to-Track Crosstalk 39 Impedances and Crosstalk: A Case History 40 Resistors 42 Through-Hole Resistors 43 Surface-Mount Resistors 43 Resistor Imperfections 45 Resistor Noise 46
    [Show full text]
  • Amplifiers Selection Guide
    0101_Price 1/6/03 3:37 PM Page 1 TM R EAL W ORLD S IGNAL P ROCESSING Amplifier Selection Guide 1Q 2003 Power Operational Amplifiers Pulse Width Modulation Drivers Voltage-Controlled Gain Integrating Logarithmic Isolation High Speed Operational Amplifiers 4-20 mA Transmitters Audio Difference and Comparators Instrumentation Digitally Programmable Gain Includes 0101_Price 1/6/03 3:37 PM Page 2 Amplifier Selection Tree Power Management REF REF Amp ADC Processor DAC Amp Operational Amplifiers Voltage-Controlled Gain Operational Amplifie (GBW < 50 MHz) page 25 (GBW < 50 MHz) pages 4-12 pages 4-12 High Speed High Speed 4-20 mA Transmitters (GBW ≥ 50 MHz) pages 13-16 page 33 pages 13-16 Comparators Logarithmic Audio pages 17-18 page 34 pages 26-30 Difference and Power and Buffers Integrating Instrumentation page 31 page 35 pages 19-23 (Galvanic) Isolation Pulse Width Digitally page 36 Modulation Drivers Programmable Gain page 32 page 24 2 Amplifier Selection Guide Texas Instruments 1Q 2003 0101_Price 1/6/03 3:37 PM Page 3 Introduction and Table of Contents Operational Amplifiers Overview . 4-5 Texas Instruments offers a wide range Precision . .6-7 of amplifiers that vary in performance, Low-Voltage . .7-8 functionality and technology. Whether Low-Power . 9 your design requires low-noise, high- Wide-Voltage Range . 10-11 precision or low-voltage micropower General Purpose . .11 signal conditioning, TI’s amplifier portfolio will meet your requirements High-Speed Amplifiers . 13-16 and with a variety of micropackage options. Comparators . 17-18 Why TI Amplifiers? Difference Amplifiers . 19-20 • High performance—maximum performance, minimum power.
    [Show full text]