Cypress Semiconductor Corporation, 198 Champion Court, San Jose, CA 95134. Tel: (408) 943-2600

PRODUCT CHANGE NOTIFICATION

PCN: PCN200503 Date: February 04, 2020

Subject: Qualification of Fab 25 as an Additional Wafer Fab Site and Marketing Part Number Change for Select MM MCU Products

To: PCN ALERTS MOUSER [email protected]

Change Type: Major

Description of Change: Cypress announces the qualification of Fab 25 (5204 East Ben White Boulevard, Austin, TX 78741, USA) as an additional wafer fab site for select Mass Market (MM) MCU products. The current products are fabricated at ON Semiconductor Aizu Co., Ltd (OSA, No.6 Kogyo Danchi, Monden-Machi, Aizu Wakamatsu, Fukushima, 965-8506, Japan). Cypress also announces that the part number is changing from a MB prefix to a CY prefix, including a marking change of “F-logo” or “ logo” removal.

Changes Current New Wafer Fab Site ON Semiconductor Aizu Co., Ltd, Japan Fab 25, USA Part Number MB*** CY*** Logo Marking F-logo or Spansion logo No logo

Benefit of Change: Qualification of alternate sites are part of the ongoing flexible manufacturing initiative announced by Cypress. The goal of the flexible manufacturing initiative is to provide the means for Cypress to continue to meet delivery commitments through dynamic, changing market conditions.

Part Numbers Affected: 4 See the attached ‘Affected Parts List’ file for a list of all part numbers affected by this change. Note that any new parts that are introduced after the publication of this PCN will include all changes outlined in this PCN.

Document No. 001-53357 Rev. *I Page 1 of 2

Qualification Status: The product has been qualified through a series of tests documented in the Qualification Test Plans summarized in the table below. These qualification reports can be found as attachments to this PCN or by visiting www.cypress.com and typing the QTP number in the keyword search window.

QTP Number Qualification 172101 8/16/32-bit , 350nm Technology (CU60F), FAB 25 192507 QFP Package, Lead-Free, JD Usuki 191002 LQFP Package, Pb-Free, TongFu

Sample Status: Qualification samples may not be built ahead of time for all part numbers affected by this change. Please review the attached ‘Affected Parts List’ file for a list of affected part numbers with their associated Fab 25 sample ordering part numbers. Sample ordering part numbers are subject to lead times. If you require qualification samples, please contact your local Cypress Sales Representative as soon as possible, preferably within 30 days of the date of this PCN, to place any sample orders.

Approximate Implementation Date: Effective 90 days from the date of this notification, all shipments of the affected part number in the attached file will be fabricated at either Fab 25 or other qualified wafer fabrication sites.

Anticipated Impact: Products fabricated at the new site are completely compatible with existing products from form, fit, functional, parametric and quality performance perspectives.

Cypress also recommends that customers take this opportunity to review these changes against current application notes, system design considerations and customer environment conditions to assess impact (if any) to their application.

Method of Identification: Cypress maintains traceability of product to wafer level, including wafer fabrication location, through the lot number marked on the package.

Response Required: No response is required.

For additional information regarding this change, contact your local sales representative or contact the PCN Administrator at [email protected].

Sincerely,

Cypress PCN Administration

Document No. 001-53357 Rev. *I Page 2 of 2 Corporation

CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25

Design Engineering Sr Manager Kunio Azuma [email protected]

Product Engineering Sr Director Hidetaka Suzuki [email protected]

Product Engineer Shoji Isawa [email protected]

Applications Engineer Hiroshi Terashima [email protected]

Marketing Engineering Sr Manager Norihiro Nakatsuhama [email protected]

www.cypress.com

198 Champion Ct. San Jose, CA 95134 USA

Tel: (408) 943 2600 Fax: (408) 943 4730

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 1 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

Characterization Report for Microcontrollers 350nm Technology Cypress FAB25

1.0 Table of Contents

1.0 Table of Contents...... 2 2.0 Introduction ...... 3 2.1 General Description ...... 3 2.2 Datasheet...... 3 2.3 White Papers ...... 3 2.4 Qualification Report ...... 3 3.0 Characterization Hardware and Setup...... 4 3.1 DC Characterization Board...... 4 3.2 DC Measurement System and Hardware ...... 4 3.3 AC Characterization Board ...... 4 3.4 AC Measurement System and Hardware ...... 4 3.5 Characterization Conditions and Parameters...... 4 4.0 DC Characterization...... 5 4.1 DC Characterization Summary ...... 5 5.0 AC Characterization...... 6 5.1 AC Characterization Summary ...... 6 Document History Page...... 7

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 2 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

2.0 Introduction

2.1 General Description

This characterization report represents 16LX Series and 8FX Series as listed in Table-1 which are fabricated in Fab25. 16LX series are a 16-bit general-purpose designed for process control in consumer devices and other applications requiring high-speed real-time processing. 8FX Series are a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources.

Series Part number CY90460 Series 16LX Series CY90485B Series 16bit Proprietary Core Microcontroller CY90820B Series CY95100H Series CY95100M Series 8FX Series CY95110A Series 8bit Proprietary Core Microcontroller CY95110B Series CY95330H Series

Table 1. Represented Products

2.2 Datasheet

See the attached datasheet.

2.3 White Papers

All products do not have any associated White Papers.

2.4 Qualification Report

All products are qualified under QTP172101. The qualification reports are available from the Cypress Website at: QTP# 172101: 350nm Technology (CU60F) Microcontroller product at Fab25 LQFP package with Cu-wire and EME-G660B Mold Compound at J-Devices Usuki for Fab25 350nm technology products

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 3 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

3.0 Characterization Hardware and Setup

3.1 DC Characterization Board

All critical DC parameters were measured on an engineering samples, with the performance board for specified ATE Tester.

3.2 DC Measurement System and Hardware

Temperature Forcing System The Thermonics T-2500E Precision Temperature Forcing System was used to force ambient temperature.

ATE Tester The Advantest T6577 was used to power the device and measure DC parameters.

3.3 AC Characterization Board

All critical AC parameters were measured on an engineering samples, with the performance board for specified ATE Tester.

3.4 AC Measurement System and Hardware

Temperature Forcing System The Thermonics T-2500E Precision Temperature Forcing System was used to force ambient temperature.

ATE Tester The Advantest T6577 was used to power the device and measure AC parameters.

3.5 Characterization Conditions and Parameters

Characterization was done on the following conditions as listed in Table.2. Units were built using standard production manufacturing and chosen randomly unless specified.

# of Voltage Range Temperature Range Parameter Device Fab Lot Assy Lot Devices (V) (°C) DC/AC CY90F462APFM-G-UJE1 J8293L0 1849N01 31 4.5V-5.5V -40, 25, 85

Table 2. Characterization Conditions and Parameters

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 4 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

4.0 DC Characterization

4.1 DC Characterization Summary

Measured Datasheet Parameter Symbol Pin name Condition Current Fab Fab25 Unit Min Max Min Max Min Max

"H" level VCC=4.5V, VCC VCC VCC VCC VCC VOH All output pins - V output voltage IOH=-4.0mA -0.5 -0.338 -0.285 -0.382 -0.294 All pins except P00 to P05 V =4.5V, CC - 0.4 0.186 0.223 0.174 0.258 V "L" level and IOL=4.0mA V output voltage OL P30 to P35 P00 to P05, V =4.5V, CC - 0.4 0.193 0.230 0.182 0.262 V P30 to P35 IOL=12.0mA

Input leakage VCC=5.5V, IIL All input pins -5 5 -0.04 0.02 -0.02 0.02 uA current VSS

VCC=5.5V, ICC VCC Internal operation at 16MHz, - 50 29.2 30.4 28.8 31 mA Normal operation VCC=5.5V, ICCS VCC Internal operation at 16MHz, - 20 10.76 11.32 10.5 11.5 mA Power supply In sleep mode current VCC=5.5V, Internal operation at 16MHz, I V - 5 1.94 2.02 1.92 2 mA CTS CC In Timer mode, TA=25°C In stop mode, I V - 20 3.14 3.24 2.82 3.32 uA CCH CC TA=25°C P00 to P07 Pull-up R P10 to P17 - 25 100 40.3 48.8 37.6 55.1 kΩ resistance UP RST Analog port I AN0 to AN7 - - 10 0.00 0.00 0.00 0.02 uA input current AIN

Power supply IA - - 6 1.40 1.58 1.36 1.66 mA AVCC current IAH - - 5 0.16 0.22 0.14 0.20 uA

Reference IR - - 900 552 576 472 514 uA voltage AVR supply current IRH - - 5 0.12 0.16 0.12 0.20 uA

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 5 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

5.0 AC Characterization

5.1 AC Characterization Summary

A/D Converter

Measured Datasheet Parameter Symbol Pin name Condition Current Fab Fab25 Unit

Min Max Min Max Min Max

Non-linear error - - VCC=AVCC=AVR=4.95V - ±2.5 -1.33 0.96 -1.74 1.81 LSB Differential linearity - - V =AV =AVR=4.95V - ±1.9 -1.56 1.63 -1.43 1.71 LSB error CC CC AV − AV + AV − AV + AV − AV + Zero transition SS SS SS SS SS SS V AN0 to AN7 V =AV =AVR=4.95V 1.5 2.5 0.30 0.12 0.48 0.27 V voltage OT CC CC LSB LSB LSB LSB LSB LSB AVR − AVR + AVR − AVR − AVR − AVR − Full-scale V AN0 to AN7 V =AV =AVR=4.95V 3.5 0.5 2.51 2.13 2.76 1.86 V transition voltage FST CC CC LSB LSB LSB LSB LSB LSB

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 6 of 7 CUSTOMER CHARACTERIZATION REPORT FOR MICROCONTROLLERS 350NM TECHNOLOGY CYPRESS FAB25 General-purpose single-chip microcontrollers Document No. 002-26924 Rev.**

Document History Page

Rev. ECN No. Orig. of Description of Change Change ** 6525802 SIIA New Characterization Report.

Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales.

Products PSoC Solutions PSoC psoc.cypress.com General psoc.cypress.com/solutions Clocks & Buffers clocks.cypress.com Low Power/Low Voltage psoc.cypress.com/low-power Wireless wireless.cypress.com Precision Analog psoc.cypress.com/precision-analog Memories memory.cypress.com LCD Drive psoc.cypress.com/lcd-drive Image Sensors image.cypress.com CAN 2.0b psoc.cypress.com/can USB psoc.cypress.com/usb

© Cypress Semiconductor Corporation, 2019. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry eCYodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection ( and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress.

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement.

All products and company names mentioned in this document may be the trademarks of their respective holders.

Company Confidential A printed copy of this document is considered uncontrolled. Refer to online copy for latest revision. Page 7 of 7