VBA1000-18 100Khz - 1000Mhz 18W Amplifier

Technology Limited

VBA1000-18 100kHz - 1000MHz 18W Amplifier

l High reliability proven GaAs design l Higher performance and efficiency than silicon alternatives l Lower cost than comparable GaN solutions l Class A for maximum mismatch drive l General linear power requirements

The VBA1000-18 is a member of our family of 100kHz- The amplifier operates in class A, the benefits for EMC 1000MHz high power amplifiers, designed primarily for applications being very low distortion and tolerance of EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding transducer and test chamber requirements on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

30 Choose GaAs Class A for the ultimate 25 in linearity, ruggedness, efficiency and 20 cost - only from Vectawave.

10 Typical Saturated Power Power Power (Watts) Typical Linear Power 5 Specification Saturated owerP Specification Linear owerP

0 See overleaf for technical specification 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-18

Electrical Frequency Range (Instantaneous) 100kHz-1000MHz Rated Output Power 18W Min (20W typical) Output Power at 1dB Gain Compression 15W Min (18-23W typical) Gain 44dB Min Third Order Intercept Point (see note 1) 54dBm Gain variation with Frequency ±3dB Harmonics at 15W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 45-63Hz Supply Power <150VA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 3U Case, 440mm Deep Mass 9kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers Fax: +44 (0) 1983 532 737 E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA1000-30 80 - 1000MHz 30W Amplifier

l Rugged push-pull MOSFET technology l Class A for maximum mismatch drive l General linear power requirements

The VBA1000-30 is a member of our family of The amplifier operates in class A, the benefits for EMC 80-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very The design is based on push-pull LDMOS technology in demanding transducer and test chamber requirements. the output stage, coupled with GaAs technology in the driver stages

Performance Chart

80 Choose GaAs Class A for the ultimate 70 in linearity, ruggedness, efficiency and 60 cost - only from Vectawave. 50

30 Power (Watts) Power 20

10 Saturated Power Speci cation Saturated Power Power at 1db GCP Speci cation Linear Power 0 See overleaf for technical specification 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-30

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 30W Min (40W typical) Output Power at 1dB Gain Compression 20W Min (25W typical) Gain 50dB Min Third Order Intercept Point (see note 1) 57dBm Gain variation with Frequency ±3dB Harmonics at Minimum Linear Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 47-63Hz Supply Power 300VA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 3U Case, 440mm Deep Mass 13kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

www.vectawave.co.uk TechnologyTechnology LimitedLimited

VBA1000-35 1 – 1000MHz 35W Amplifier

l Rugged push-pull MOSFET technology l Class A for maximum mismatch drive l General linear power requirements

The VBA1000-35 is a 1MHz-1000MHz high power The amplifier operates in class A, the benefits for EMC amplifier, designed primarily for EMC applications. applications being very low distortion and tolerance of 100% mismatch. Fold-back protection is neither fitted The design is based on latest generation push-pull nor needed! This makes it supremely suited for very LDMOS technology in the output stage, coupled with demanding transducer requirements. GaAs technology in the driver stages. It employs proprietary transmission network techniques, giving little degradation of output power up to the high frequency limit.

Performance Chart

90 Choose Vectawave for high efficiency 80 70 and performance in your regular power 60 amplifier requirements. 50

Power (Watts) Power Saturated Power 20 Power at 1db GCP Speci cation Saturated Power 10 Speci cation Linear Power 0 See overleaf for technical specification 1 10 100 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-35

Electrical Frequency Range (Instantaneous) 1MHz-1000MHz Rated Output Power 35W Min (45W typical) Output Power at 1dB Gain Compression 20W Min (25W typical) Gain 50dB Min Third Order Intercept Point (see note 1) 57dBm Gain variation with Frequency ±3dB Harmonics at Minimum Linear Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 47-63Hz Supply Power 300VA (Max) Mains Connector IEC320

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1 Mains Harmonic Currents EN61000-3-2 Voltage Fluctuations and Flicker EN61000-3-3

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW TechnologyTechnology LimitedLimited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA1000-45 10kHz – 1GHz 45W Amplifier

 Specialist GTEM cell driver  Rugged push-pull MOSFET technology  Class A for maximum mismatch drive  General linear power requirements

The VBA1000-45 is an ultra broad-band high power The amplifier operates in class A, the benefits for EMC amplifier operating over an instantaneous frequency applications being very low distortion and tolerance of range of 10kHz to 1GHz, designed primarily for EMC 100% mis-match. Fold-back protection is neither fitted applications. It is particularly useful as a driver for nor needed! This makes it supremely suited for very GTEM cells and CDNs. demanding transducer requirements

The design is based on latest generation push-pull LDMOS technology in the output stage, coupled with GaAs technology in the driver stages. It employs proprietary transmission network techniques, giving little degradation of output power up to the high frequency limit.

Performance Chart

90 Choose Vectawave for high efﬁ ciency 80 70 and performance in your regular power 60 ampliﬁ er requirements. 50

Power (Watts) Power Saturated Power 20 Power at 1db GCP Speci cation Saturated Power 10 Speci cation Linear Power 0 See overleaf for technical speciﬁ cation 0.01 0.1 1 10 100 400 700 1G

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-45

Electrical Frequency Range (Instantaneous) 0.01-1000MHz Rated Output Power 0.01-400MHz 45W Min 400-1000MHz 35W Min Linear Power at 1dB Gain Compression 0.01-400MHz 35W Min 400-1000MHz 20W Min Gain 50dB Min Third Order Intercept Point (see note 1) 57dBm Gain variation with Frequency ±3dB Max Harmonics at Minimum Linear Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 47-63Hz Supply Power 300VA (Max)

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Mains Connector Style IEC320 Dimensions 19 inch, 3U Case, 440mm Deep Mass 13kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

www.vectawave.co.uk TechnologyTechnology LimitedLimited

VBA1000-65 80 – 1000MHz 65W Amplifier

The VBA1000-65 is a member of our family of The amplifier operates in class A, the benefits for EMC 80-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding transducer and test chamber requirements. on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

140 Choose GaAs Class A for the ultimate 120 in linearity, ruggedness, efficiency 100 and cost – only from Vectawave. 80

Power (Watts) Power 40 Saturated Power Power at 1db GCP 20 Speci cation Saturated Power Speci cation Linear Power

0 See overleaf for technical specification 80 150 250 350 450 550 650 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-65

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 65W Min Output Power at 1dB Gain Compression 55W Min Gain 49dB Min Third Order Intercept Point (see note 1) 58dBm Gain variation with Frequency ±3dB Harmonics at 55W output power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 45-63Hz Supply Power <500VA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 4U Case, 550mm Deep Mass 15kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

www.vectawave.co.uk Technology Limited

VBA1000-70 10 - 1000MHz 70W Amplifier

The VBA1000-70 is a member of our family of The amplifier operates in class A, the benefits for EMC 10-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding transducer and test chamber requirements. on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

140 Choose GaAs Class A for the ultimate 120 in linearity, ruggedness, efficiency and 100

80 cost - only from Vectawave.

40 Typical Saturated Power Power Power (Watts) Typical Linear Power 20 Specification Saturated owerP Specification Linear owerP 0 See overleaf for technical specification

0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-70

Electrical Frequency Range (Instantaneous) 10-1000MHz Rated Output Power 70W Min (100W typical 10-500MHz) Output Power at 1dB Gain Compression 60W Min (80W typical 10-500MHz) Gain 49dB Min Third Order Intercept Point (see note 1) 58dBm Gain variation with Frequency ±3dB Harmonics at 60W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 45-63Hz Supply Power <500VA (Max) Mains Connector IEC320

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

www.vectawave.co.uk Technology Limited

VBA1000-100 80 - 1000MHz 100W Amplifier

The VBA1000-100 is a member of our family of The amplifier operates in class A, the benefits for EMC 80-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding antenna and test chamber requirements. on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

250 Choose GaAs Class A for the ultimate 200 in linearity, ruggedness, efficiency and

150 cost - only from Vectawave.

100

Typical Saturated Power Power (Watts) Power Typical Linear Power 50 Speci cation Saturated Power Speci cation Linear Power See overleaf for technical specification 0 80 90 100 200 300 500 700 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-100

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 100W Min (110W typical) Output Power at 1dB Gain Compression 90W Min (95W typical) Gain 51dB Min Third Order Intercept Point (see note 1) 60dBm Gain variation with Frequency ±2dB Harmonics at 90W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 45-63Hz Supply Power <1kVA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to mute USB/GPIB Interface Optional Dimensions 19 inch, 4U Case, 550mm deep Mass 23kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

www.vectawave.co.uk Technology Limited

VBA1000-150 80 - 1000MHz 150W Amplifier

The VBA1000-150 is a member of our family of The amplifier operates in class A, the benefits for EMC 80-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding antenna and test chamber requirements. on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

300 Choose GaAs Class A for the ultimate 250 in linearity, ruggedness, efficiency and 200 cost - only from Vectawave.

150

100 Typical Saturated Power Power Power (Watts) Typical Linear Power 50 Specification Saturated owerP Specification Linear owerP

0 See overleaf for technical specification 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-150

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 150W Min (175W typical 80-500MHz) Output Power at 1dB Gain Compression 120W Min (150W typical 80-500MHz) Gain 52dB Min Third Order Intercept Point (see note 1) 61dBm Gain variation with Frequency ±2dB Harmonics at 120W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 45-63Hz Supply Power <1kVA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 4U Case, 550mm Deep Mass 23kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

www.vectawave.co.uk Technology Limited

VBA1000-250S 80 - 1000MHz 250W Amplifier

l Rugged push-pull Silicon LDMOS technology l Class A for maximum mismatch drive l General linear power requirements

The VBA1000-250S is an 80-1000MHz high power The amplifier can be controlled from either the front amplifier, designed primarily for EMC applications. panel or remote control via the Ethernet, USB and GPIB interfaces. The digital interface system manages The amplifier produces around 300W P1dB at the enabling and disabling the amplifier, monitoring power important VHF frequencies, and is housed in a compact levels, monitoring power supply health, communicating 4U case. VBA1000-250S is intended for applications with the control computer and implementing electrical where an 18V/m field is required and incorporates interlocks. The keypad and display interface is used for measures to improve power delivery into high VSWR monitoring amplifier state, power levels, interlock states loads. etc. and for configuration options.

Performance Chart

700

600

500

400

300

Power (Watts) Power 200 Typical Saturated Power Typical Linear Power 100 Speci cation Saturated Power Speci cation Linear Power 0 0 100 200 300 400 500 600 700 800 900 1000 See overleaf for technical specification

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-250S

Electrical Frequency Range (Instantaneous) 80-1000MHz Output Power at 3dB Gain Compression 350W 80MHz to 100MHz 400W 100MHz to 400MHz 300W 400MHz to 800MHz 250W 800MHz to 950MHz de-rating slope of 2.2W/MHZ 950MHz to 1000MHz Output Power at 1dB Gain Compression 250W 80MHz to 100MHz 300W 100MHz to 400MHz 250W 400MHz to 800MHz 200W 800MHz to 950MHz de-rating slope of 2.2W/MHZ 950MHz to 1000MHz Gain 56dB Min Third Order Intercept Point (see note 1) 64dBm Gain variation with Frequency ±3dB Harmonics at P1dB Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 100 - 240V ac (+/- 10%) Supply Frequency Range 45-63Hz Supply Power <1kVA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock Dual input, S/C and/or O/C to Mute Remote Control Interface USB/GPIB/Ethernet Dimensions 19 inch, 4U Case, 500mm deep Mass 18kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:2013 Table 1 Safety EN61010-1

www.vectawave.co.uk VBA1000-275 80 - 1000MHz 275W Amplifier

The VBA1000-275 is a member of our family of The amplifier operates in class A, the benefits for EMC 80-1000MHz high power amplifiers, designed primarily applications being very low distortion and tolerance of for EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA1000 series, it is based demanding antenna and test chamber requirements. on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

Performance Chart

520

Typical Saturated Power Choose GaAs Class A for the ultimate 470 Linear (1dB) Power Specification Saturated owerP in linearity, ruggedness, efficiency and Linear (1dB) Power Specification 420 cost - only from Vectawave.

370

320 Power Power (Watts)

270

220 See overleaf for technical specification 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-275

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 275W Min (350W typical 80-500MHz) Output Power at 1dB Gain Compression 250W Min (300W typical 80-500MHz) Gain 56dB Min Third Order Intercept Point (see note 1) 64dBm Gain variation with Frequency ±3dB Harmonics at 200W Output Power -20dBc Max Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity any Phase Input VSWR 2:1 (Max) Supply Voltage 184-264V ac Supply Frequency Range 45-63Hz Supply Power 2kVA (Max) Mains Connector IEC320 C20

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 6U Case, 550mm Deep Mass 25kg Operating Temperature Range 0-40°C Case Style Options Rack mount with front or rear panel connectors Bench mount with front panel connectors Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers Fax: +44 (0) 1983 532 737 E-mail: [email protected]

www.vectawave.co.uk VBA1000-500 80 - 1000MHz 500W Amplifier

The VBA1000-500 is a member of our family of 80-1000MHz high power amplifiers, designed primarily for EMC applications.

Like all our products of the VBA1000 series, it is based on our unique GaAs technology, offering the user the benefits of higher linearity, ruggedness and efficiency than its silicon-based counterparts and lower cost than the more recent GaN additions to the marketplace.

The amplifier operates in class A, the benefits for EMC applications being very low distortion and tolerance of 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very demanding antenna and test chamber requirements.

Performance Chart

1000 900 Choose GaAs Class A for the ultimate 800 in linearity, ruggedness, efficiency and 700 600 cost - only from Vectawave. 500 400 Typical Saturated Power

Power Power (Watts) 300 Linear (1dB) Power 200 Specification Saturated owerP Linear (1dB) Power Specification 100 See overleaf for technical specification 0 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-500

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 500W Min (700W typical 80-500MHz) Output Power at 1dB Gain Compression 440W Min (600W typical 80-300MHz) (500W typical 80MHz-1.0GHz) Gain 58dB Min Third Order Intercept Point (see note 1) 66dBm Gain variation with Frequency ±3dB Harmonics at 400W Output Power -20dBc Max Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity any Phase Input VSWR 2:1 (Max) Supply Voltage see options for 3 phase configuration Supply Frequency Range 45-63Hz Supply Power <4kVA (Max) Mains Connector Appropriate IEC60309 plug (see options)

Mechanical RF Connector Style RF in N type, RF out 7/16 Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 25U Rack, 800mm Deep Mass 110kg Operating Temperature Range 0-40°C Case Style Options Rack mount with rear panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Options 3 Phase Delta (5 pin plug) or 3 Phase Star (5 pin plug)

www.vectawave.co.uk Technology Limited

VBA1000-1000 80 - 1000MHz 1000W Amplifier

The VBA1000-1000 is a member of our family of 80-1000MHz high power amplifiers, designed primarily for EMC applications.

Performance Chart

2000 1800 Choose GaAs Class A for the ultimate 1600 in linearity, ruggedness, efficiency and 1400 1200 cost - only from Vectawave. 1000 800 Typical Saturated Power

Power (Watts) Power 600 Linear (1dB) Power 400 Specication Saturated Power Linear (1dB) Power Specication 200 See overleaf for technical specification 0 0 100 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-1000

Electrical Frequency Range (Instantaneous) 80-1000MHz Rated Output Power 1000W Min (1400W typical 80-500MHz) Output Power at 1dB Gain Compression 800W Min (1200W typical 80-500MHz) (1000W typical 500MHz-1.0GHz) Gain 61dB Min Third Order Intercept Point (see note 1) 70dBm Gain variation with Frequency ±3dB Harmonics at 800W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity any Phase Input VSWR 1.5:1 (Max) Input power required for 1000W output. 0dBm (Max) Maximum permitted input power. 10dBm Supply Voltage see Options for 3 Phase configuration Supply Frequency Range 45-63Hz Supply Power <6kVA (Max) Mains Connector Appropriate IEC60309 plug (see options) Cooling Air cooled with internal fans

Mechanical RF Connector Style Input Type N Female, Output 7/16 Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch 34U rack, 800mm deep Mass 200kg Operating Temperature Range 0-40°C Case Style Options Rack mount with rear panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Options 3 Phase Delta (5 pin plug) or 3 Phase Star (5 pin plug)

www.vectawave.co.uk Technology Limited

VBA1000-2000 200 - 1000MHz 2000W Amplifier

 High reliability proven GaAs design  Higher performance and efficiency than silicon alternatives  Lower cost than comparable GaN solutions  Class A for maximum mismatch drive  Automotive testing  General linear power requirements

The VBA1000-2000 is a 200-1000MHz high power amplifier, designed primarily for EMC applications.

Performance Chart

3900 3700 Typical Saturated Power Choose GaAs Class A for the ultimate 3500 Linear (1dB) Power Specication Saturated Power 3300 in linearity, ruggedness, efﬁ ciency and Linear (1dB) Power Specication 3100 2900 cost - only from Vectawave. 2700 2500 2300

Power (Watts) Power 2100 1900 1700 1500 See overleaf for technical speciﬁ cation 200 300 400 500 600 700 800 900 1000

Frequency (MHz)

www.vectawave.co.uk Specifications VBA1000-2000

Electrical Frequency Range (Instantaneous) 200-1000MHz Rated Output Power 2000W Min (2500W typical 200-500MHz) Output Power at 1dB Gain Compression 1800W Min (2000W typical 200-500MHz) (1900W typical 800MHz-1.0GHz) Gain 64dB Min Third Order Intercept Point (see note 1) 74dBm Gain variation with Frequency ±3dB Harmonics at 1800W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 184-264V AC Delta or 319-457 AC Star Supply Frequency Range 45-63Hz Supply Power <12kVA (Max) Mains Connector Appropriate IEC60309 plug (see options)

Mechanical RF Connector Style Input Type N Female, Output 1-5/8” EIA Flange Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 2x34U Rack plus 200mm centre panel, 800mm Deep Mass 400kg Operating Temperature Range 0-40°C Case Style Options Rack mount with rear panel connectors

Options 3 Phase plus P.E. Delta Connection (No neutral) 3 Phase, Neutral plus P.E. Star Connection