Quick Start Guide Access Point & Client Bridge

This Guide will assist you in setting up the Client Bridge as quickly as possible and with the least effort.

Hardware Installation this device, you must first configure the TCP/IP settings of your PC/Notebook. Indoor Application 1. In the control panel, double click ECB-3610S/8610S/8610 Series Network Connections and then double click on the connection of your Network 1. Place the unit in an appropriate place Interface Card (NIC). You will then see after conducting a site survey. the following screen. 2. Plug one end of the cable into 2. Select Internet Protocol (TCP/IP) and the RJ-45 port of the device and another then click on the Properties button. This end into your PC/Notebook. will allow you to configure the TCP/IP 3. Insert the DC-inlet of the power adapter settings of your PC/Notebook. into the port labeled “DC-IN” and the 3. Select Use the following IP Address other end into the power socket on the button and then enter the IP wall. address (192.168.1.21) and subnet mask (255.255.255.0). Ensure that the Ethernet IP address and subnet mask are on the PC Bridge/AP same subnet as the device. 4. Click on the OK button to close this AC/DC cable window, and once again to close LAN properties window.

PWR Outlet

Logging In

1. To configure the Bridge through the Outdoor Application web-browser, enter the IP address of the Bridge (default: 192.168.1.1) into the EOC-3610S/8610S/8610 Series address bar of the web-browser and 1. Place the unit in an appropriate place press Enter. after conducting a site survey. 2. After connecting to the IP address, the 2. Plug one end of the Ethernet cable into web-browser will display the login page. the AP port of the PoE Injector and the Specify the User Name and Password. other end into the Bridge/AP. The device does not have a user name 3. Place one end of another Ethernet cable and password configured by default, into the Network port of the PoE Injector leave user name and password field blank and another end into your PC/Notebook. and then click on the Login button. 4. Insert the DC-inlet of the power adapter into the port labeled “DC-IN” and the (LAN) Settings other end into the power socket on the wall. 1. Click on the LAN link on the navigation drop-down menu. This feature allows Ethernet PC PoE Injector you to configure the LAN interface using a static IP address or as a DHCP client. AC/DC cable Ethernet This IP address is also used to access the web-based interface. PWR Outlet AP/Bridge 2. IP Address Mode: Select the Static or DHCP radio button. DHCP does not require the rest of the fields to be filled in. IP Address Configuration 3. IP Address: Enter an IP address for this device. This device can be configured as a Client 4. Subnet Mask: Enter the subnet mask for Bridge The default IP address of the device is this IP address. 192.168.1.1 (CB mode) In order to log into

1 Quick Start Guide v.1.0 Refer to User’s Manual for complete instructions

Quick Start Guide Wireless Access Point & Client Bridge

5. Default Gateway: Enter the IP address 3. Name: The SSID is a of the default gateway. unique named shared amongst all the 6. Click on the Save Settings button once points of the wireless network. The SSID you have modified the settings. must be identical on all points of the Note: If you change the IP address here, you wireless network and cannot exceed 32 may need to adjust your PC’s network characters. settings to access the network again. 4. Channel: Select a channel from the drop-down list. Wireless LAN Settings 5. Transmission Rate: Select a rate from the drop-down list. It is recommended to 1. Click on the Wireless_Setting link under use the Best (automatic) option. the Wireless menu. 6. 802.11 Mode: Select the IEEE 802.11 2. Wireless Mode: Select Infrastructure mode from the drop-down list. or Ad-Hoc radio button. 7. Click on the Save Settings button once you have modified the settings.

2 Quick Start Guide v.1.0 Refer to User’s Manual for complete instructions

Quick Start Guide Wireless Access Point & Client Bridge

This Guide will assist you in setting up the Access Point as quickly as possible and with the least effort.

Hardware Installation

This device can be configured as a Access Indoor Application Point. The default IP address of the device is 192.168.1.2 (AP mode) In order to log into ECB-3610S/8610S/8610 Series this device, you must first configure the TCP/IP settings of your PC/Notebook. 1. Place the unit in an appropriate place after conducting a site survey. 1. In the control panel, double click 2. Plug one end of the Ethernet cable into Network Connections and then double the RJ-45 port of the device and another click on the connection of your Network end into your PC/Notebook. Interface Card (NIC). You will then see 3. Insert the DC-inlet of the power adapter the following screen. into the port labeled “DC-IN” and the 2. Select Internet Protocol (TCP/IP) and other end into the power socket on the then click on the Properties button. wall. This will allow you to configure the TCP/IP settings of your PC/Notebook. Ethernet 3. Select Use the following IP Address PC Bridge/AP radio button and then enter the IP address (192.168.1.21) and subnet AC/DC cable mask (255.255.255.0). Ensure that the

IP address and subnet mask are on the

PWR Outlet same subnet as the device. 4. Click on the OK button to close this window, and once again to close LAN properties window. Outdoor Application Logging In EOC-3610S/8610S/8610 Series 1. To configure the Access Point through 1. Place the unit in an appropriate place the web-browser, enter the IP address after conducting a site survey. of the Access Point (default: 2. Plug one end of the Ethernet cable into 192.168.1.2) into the address bar of the the AP port of the PoE Injector and the web-browser and press Enter. other end into the Bridge/AP. 2. After connecting to the IP address, the 3. Place one end of another Ethernet cable web-browser will display the login page. into the Network port of the PoE Injector Specify the User Name and Password. and another end into your PC/Notebook. The device does not have a user name 4. Insert the DC-inlet of the power adapter cand password onfigured by default, into the port labeled “DC-IN” and the leave user name and password field blank other end into the power socket on the and then click on the Login button. wall. LAN (Local Area Network) Ethernet PC PoE Injector 1. Click on the LAN link under the Basic AC/DC cable Ethernet menu.on the navigation drop-down menu. This feature allows you to PWR Outlet AP/Bridge configure the LAN interface using a static IP address or as a DHCP client/server. This IP address is also IP Address Configuration used to access the web-based interface.

3 Quick Start Guide v.1.0 Refer to User’s Manual for complete instructions Quick Start Guide Wireless Access Point & Client Bridge

2. IP Address: Enter an IP address for this device. 3. Subnet Mask: Enter the subnet mask for this IP address. 4. Gateway: Enter the IP address of the default gateway. 5. Local Domain Name: Enter a local domain name. This field is optional. Save Settings 6. Click on the button once you have modified the settings.

Note: If you change the IP address here, you

may need to adjust your PC’s network

settings to access the network again.

Wireless LAN Settings

1. Click on the Wireless link on the navigation drop-down menu. 2. Wireless Network Name: The SSID is a unique named shared amongst all the points of the wireless network. 3. Visibility Status: Select Visible or Invisible. This is the SSID broadcast feature. 4. Channel: Select a channel from the drop-down list. 5. Transmission Rate: Select a rate from the drop-down list. It is recommended to use the Best (automatic) option. 6. 802.11 Mode: Select the IEEE 802.11 mode from the drop-down list. 7. Click on the Save Settings button once you have modified the settings.

P/N: 6709A0253000

4 Quick Start Guide v.1.0 Refer to User’s Manual for complete instructions