FP 311 Intumescent

FIRE RETARDANT INTUMESCENT SEALING COMPOUND

ADVANTAGES

- CE-marked - Easy to apply - Up to 4-hour fire resistance - High sound insulation - Low emission - environmentally and user friendly

PRODUCT Bostik FP 311 Intumescent Graphite is a high specification formulation designed to prevent the spread of fire, smoke and gasses through openings in fire rated walls and floors.

Bostik FP 311 Intumescent Graphite is a single component, - Easy to apply waterbased, fire retardant sealing compound which - Fast curing, tack free after 1 hour contains a high concentration of heat expanding graphite - Paintable with most water based and alkyd paints material. Bostik FP 311 Intumescent Graphite expands when - Complies with requirements of M1 Protocol it is subjected to fire and closes openings around - Emicode EC1Plus combustible pipes (e.g. PVC) or pipes fitted with - A+ French VOC Regulation combustible insulation. Thermal activation takes place at - 18 months storage time (under correct conditions) 150°C when the material will intumesce to prevent the spread of fire, smoke and gases through openings up to 4 METHOD OF USE hours. Before applying Bostik FP 311 Intumescent Graphite ensure that the surface of all service penetrations and surrounding Bostik FP 311 Intumescent Graphite offers a very good is free from all loose contaminants, dust and sound insulation. grease. When installing any backing material, cut this slightly oversize and insert into the gap ensuring a tight APPLICATIONS friction fit. Ensure correct depth is achieved. Fill the gap or Bostik FP 311 Intumescent Graphite is designed to close off joint with Bostik FP 311 Intumescent Graphite to the large voids left by pipes and combustible insulation required depth. Apply the sealant generously avoiding air as they melt and burn gaps and fire seal difficult services bubbles. Finish the bead with a moist spatula or pallet knife. which traditional fire rated mastics do not achieve. Avoid excessive tooling/smoothing as this may make the Bostik FP 311 Intumescent Graphite can be used with a seal surface wet and soft. suitable filling material, i.e. stone wool or Bostik backing material in order to ensure the correct width to depth ratio Before application consult the installation instructions and and to reduce the shrinkage of the sealant during curing. ETA to ensure to achieve the intended fire resistance.

FEATURES - Certified to the latest European standards EN 1366-3 - CE Marked to ETAG 026 part 2 - Classified in most for plastic pipes and cables - Suitable for most surfaces, included , bricks, , wood, gypsum, PVC and most non-porous surfaces - No priming necessary for application to most materials - Fire resistance up to 4 hour - High sound insulation of SaleandDelivery. executed works can beassumed on the basis of this documentation. Therefore we advise you to perform a test on the spot yourself. All our salesanddeliveries are subject to our General Conditions necessary. Considering that the designandconditions of the substrate and the circumstances under which the application takes place are beyond our control, noresponsibility with regard to the been taken to compile the documentation, we assume noresponsibility for inaccuracies, mistakes, typographical or print errors. We reserve the right to alter the product whenever we deem All advice, recommendations, figures andsafety instructionsare basedupon thorough research as well as the current state of our experience andare non-binding.Despite the greatest care having www.bostik.nl T: +31 (0) 162491000 4903 RC Oosterhout Denariusstraat 11 Bostik BV - ETA 19/0395 Graphite - Installation InstructionsBostikFP 311Intumescent - Material safety data sheet Available onrequest: FURTHER INFORMATION limited shelf life once the cartridge hasbeenopened. and +30 °C.Shelf life 18months after production. Hasa Store inunopenedpackaging indry conditions between +5 STORAGE STABILITY ------LIMITATIONS sealant only. material isoptional, due to the tests beingconducted with according to ENISO10140-2:2010. Usage of any backing Bostik FP 311Intumescent Graphite hasbeen tested Double sidedseal ≥25mmdepth >Rw 53dB Single sidedseal ≥25mmdepth Rw 53dB SOUND INSULATION metal surface prior to this installation. may require abarrier between the sealant and the cases where corrosion protection isaproblem; some As BostikFP 311Intumescent Graphite is water based,in the ground. Should not beusedinjoints at floor level or joints below Should not beusedinjoints with highmovement. Should not beusedinpermanently dampareas. Suitable for singleservice penetrations only used Indirect contact with bituminousmaterials. Suitable for use with mostmaterials, butshouldnot be www.bostik.be T: +32 (0) 92551717 B-900 Gent Meulestedekaai 86 Bostik BeluxSA -NV www.bostik.co.uk T: +44(0) 1785272625 3EH ST16 Common Road, Stafford Bostik Ltd Pallet quantity Packed per Article number Colour Packaging Durability Movement capability Expansion rate Curing time Skin formation Tack free Flash point Density Application temperature Base Technical data Smart help

1248 12 cartridges 30614867 Anthracite Cartridge 310ml Class Z2 12.5% (ISO11600) 1 :16 thickness and temperature 3 to 5days dependingon Max. 30minutes Max. 60minutes None Approx. 1.55g/ml +4°C to +30°C Water based graphite filler www.bostik.ie T: +353 (1)8624900 Swords, Co. Dublin Newton Bostik IndustriesLtd.

NL-2020/01/08