Axerra Networks and Narad Networks Field Test Scalable T1 Solution for Wireless Backhaul Over HFC

Total Page:16

File Type:pdf, Size:1020Kb

Axerra Networks and Narad Networks Field Test Scalable T1 Solution for Wireless Backhaul Over HFC Media Contact Axerra Networks: Media Contact JLM Partners for Narad Steve Byars Networks: 561-213-3659 Stacy Oaksmith [email protected] 206-381-3600 [email protected] Axerra Networks and Narad Networks Field Test Scalable T1 Solution for Wireless Backhaul over HFC Field tests demonstrate that joint solution meets stringent latency and differential delay requirements of mobile wireless backhaul Boca Raton, FL. and Westford, MA. – March 29, 2006 – Axerra Networks, “The Pseudo-Wire Company TM” and a leader in providing circuit emulation and service emulation solutions over packet access networks, and Narad Networks, Inc., a provider of high performance switched broadband access solutions, announce successful field testing of their T1 backhaul solution. The two companies will highlight their mobile wireless backhaul over HFC solution at CTIA Wireless 2006, April 5-7, Las Vegas, in the Axerra booth (#152). The combined solution of Narad and Axerra delivers an end-to-end latency of less than 8ms enabling Multiple System Operators (MSOs) to satisfy the most stringent differential delay requirements of mobile wireless backhaul. This new benchmark in HFC performance is achieved using the Axerra AXN Pseudo-Wire platforms and Narad’s switched Ethernet over Coax solution, avoiding the need for fixed wireless solutions or costly new fiber construction. “Mobile operators are looking for cost-effective primary backhaul service and for redundancy and route diversity options,” said Michael Collette, Narad Networks CEO. “This QoS-based solution will allow mobile operators to choose between cable operators and incumbent local exchange carriers as suppliers of backhaul service, driving down the cost of infrastructure.” “The combined Axerra / Narad solution allows MSOs to cost-effectively attack the $2 billion wireless backhaul market. Using the HFC network reduces MSO build costs, and Narad’s NBAN architecture resolves the scalability and performance shortcomings of prior HFC transport,” said Gadi Tamari, CEO, Axerra Networks. Axerra Networks’ family of AXN Pseudo-Wire Gateways and Access Devices™ furnish full- service capabilities over the HFC and fiber infrastructure of cable networks, including leased line T1 PCM Voice, T1 Private Line Data, Ethernet Private Line, native Frame Relay, ATM, HDLC, and IP services. The low latency and high-precision clock recovery features of Axerra’s Pseudo- 1 Wire solution support the most demanding applications of the T1 Business Services and Mobile Wireless Backhaul markets. The AXN family is a scalable solution that addresses SMB locations and cell sites, MTU and Hubs, and the carrier-class CO environment. Narad's Ethernet-over-Coax solution provides up to 100 Mbps x 100 Mbps of additional bandwidth over each coaxial cable span. In combination with Narad Ethernet switches, these 100 Mbps symmetrical links can be switched onto the coax plant at multiple points to provide Gigabits of symmetric bandwidth per node. Narad's switched Ethernet-over-Fiber solution provides Gigabit fiber capacity while making optimally efficient use of existing fiber plant. Narad's Ethernet-based outdoor switches support fiber, coax and wireless transmissions. About Axerra Networks Axerra Networks is the leading provider of Pseudo-Wire circuit emulation and service emulation solutions over packet networks. Axerra’s AXN Pseudo-Wire Gateways and Access Devices™ enable cable MSOs, mobile wireless operators, competitive access providers, and incumbent carriers to extend IP + legacy data and voice services in native format over Ethernet, IP, and MPLS networks. The result is greater operational efficiency, new revenue opportunities, and a smooth migration strategy to a single converged network, without stranding any revenue streams from profitable legacy services. With Axerra’s Pseudo-Wire solutions, service providers can convert any packet access network (Carrier Ethernet, broadband wireless including WiMAX, cable HFC, xDSL, PON, etc.) into a full-service alternative to TDM access. For more information, visit: www.axerra.com . About Narad Networks Narad Networks is a provider of switched broadband access solutions that enable cable operators to leverage existing coaxial cable and flexibly use fiber and wireless media to deliver high capacity, high performance IP services, including voice, data, video, and enterprise networks. The company's QoS switches and service management software, along with its broad spectrum fiber and coax transmission technologies, support multi-gigabit transport for both commercial and residential customers. Narad's patented Ethernet-over-Coax solution meets the needs of coax-based users that have voice or data needs beyond that which cable modems can offer, while Narad's switched Ethernet-over-Fiber solution provides unprecedented IP capacity to fiber-based customers. Narad is currently deployed with North American and European cable operators. Based in Westford, Massachusetts, Narad is a privately held company with venture funding from Argo Global Capital, Polaris Venture Partners and other leading venture capital firms. For more information, visit www.naradnetworks.com . ## 2 .
Recommended publications
  • EQCO800SC Datasheet
    Engineering Information EqcoLogic NV Open your Eyes™ EQCO875SC.3/ EQC850SC.3 Single Coax Transceiver for Fast Ethernet 1.1 Features . Combined transmitter and receiver with an integrated equalizer to form a full-duplex bidirectional connection over a single 75Ω coax cable (EQCO875SC.3) or 50Ω coax cable (EQCO850SC.3) . Compatible with FX version of Fast Ethernet . Low Power - 205mW from single 3.3V supply . Integrated termination resistors for low external discrete count . Fully supports PoE based Power distribution over the coax, on top of the data signals . 16-pin, 0.65mm pin pitch, 4mm QFN package . Pb-free and RoHS compliant 1.2 Applications This solution is useful and economical for many markets and applications, including the following: . Camera networks - Home Security, Surveillance, industrial/inspection, medical cameras . Home Networking over coax infrastructure When Cat5 or Cat6 cabling is not available and existing 75Ω coax is not used for analogue TV signals. TV, STB, PVR connections including inter-room links 1.3 Typical Cable Lengths Version EQCO875SC range using RG11 RG6 ( 5mm) EQCO875SC.3 225m 150m Table 1: Typical Device Performance DS-EQCO875SC.3 (Ethernet)-2v0-2011-10-25 Page 1 of 11 ©2014 Eqcologic NV Engineering Information EqcoLogic NV Open your Eyes™ 2 Functional Description 2.1 Overview The EQCO875SC.3 single coax transceiver is designed to simultaneously transmit and receive signals on a single 75Ω coax cable for fast ethernet. A sister product, the EQCO850SC.3 can achieve similar performance when used in 50Ω coaxial systems The EQCO875SC.3 is ideally suited for Fast Ethernet connections over 75Ω coax cable at 125Mbps1 data rate.
    [Show full text]
  • Poe Considerations in Ethernet Over Coax Applications
    PoE Considerations in Ethernet over Coax Applications Power-over-Ethernet (PoE) is an effective tool for powering Ethernet devices that need to be located in areas where power is not currently available and would be difficult or costly to install. In such cases, power can be provided over existing cable, such as coaxial cabling, which simplifies installation, saves time, and eliminates the cost of new wiring or hiring an electrician. Transition Networks’ Ethernet Over Coax Extender With PoE+ converts conventional Ethernet to a signal that can be carried over 75 ohm impedance coaxial cable, allowing upgrades from analog cameras to high-quality digital IP cameras in security and surveillance applications, interconnection of communication equipment in cellular backhaul applications, and interconnection of wireless equipment in WAN/LAN networks – all without the high cost of replacing the existing coax cable. It may be tempting to compare Ethernet extenders from various manufacturers based on a single factor such as distance. However, it is important to note that many additional factors affect the total performance of a PoE solution and results can vary greatly. When comparing products from different vendors, one must consider the following factors to determine their effect throughout the entire system: • Power level needed at the end device • Desired data throughput rates • Operating temperature of the environment • Distance to the end device • The quality of the coax cable used Power at the End Device In order to be compliant with IEEE 802.3af standards, a PoE system must deliver 15.4 Watts of power to the end device. To be IEEE 802.3at compliant, a PoE+ system must deliver a full 30 Watts of power to the end device.
    [Show full text]
  • Cable and Mobile Convergence
    Cable and Mobile Convergence A Vision from the Cable Communities Around the World A Technical Paper prepared for SCTE•ISBE by Jennifer Andréoli-Fang, PhD John T. Chapman Distinguished Technologist CTO Cable Access, Cisco Fellow CableLabs Cisco [email protected] [email protected] Charter Communications Ahmed Bencheikh, Group Vice President Praveen Srivastava, Director Vikas Sarawat, Consulting Engineer Cisco Ian Campbell, CTO Mobility, Distinguished Engineer Mark Grayson, Distinguished Engineer Cox Communications Drew Davis, Executive Director Paul Blaser, Director Shaw Communications Damian Poltz, Senior Vice President Dave Morley, Director Telecom Eduardo Panciera, Chief Architect Argentina Vidéotron Philippe Perron, Director Sylvain Archambault, Director Eric Menu, Architect Géraldine Trouillard, Architect David Lagacé, Architect Vodafone Gavin Young, Head of Fixed Access Centre of Excellence Bruno Cornaglia, Distinguished Engineer, Fixed Access Sr Manager © 2020 SCTE•ISBE and NCTA. All rights reserved. 1 Table of Contents Title Page Number 1. Introduction .......................................................................................................................................... 5 2. Four Stories of Convergence .............................................................................................................. 7 2.1. Business Convergence .......................................................................................................... 7 2.2. Infrastructure Convergence ...................................................................................................
    [Show full text]
  • Creating the Connected Home
    The Connected Home Enabling Technologies and New Service Models Creating a Connected Home • Interest stems from triple play service delivery » IPTV initially, RF overlay added » Began with residential gateway set top devices • “Connected home” has different connotations: » Connecting services (voice, data, video) » Utilization of in-home wiring for service distribution » Creating a ubiquitous home network » “Smart home” • Connected home is both a technology choice and service architecture decision » Where the service provider demarcation is » How and where service management extends Strategies for Connected Home Creation • Fiber to the premise for broadband bandwidth • Ethernet distribution • Multi-Service, Multi-Play • Service Provider has ROI – can make money from it Competing Interests: • 4G wireless as the connected home technology • Everything transitions to the Internet – no new service opportunity for the carrier except bandwidth Connected Home Needs Often ROI Based CAPEX OpEx Revenues Reduce in home wiring Service management Bundling services Lower installation time Fewer truck rolls Enhanced services Lower labor costs Interface outside home Quality of services Lower equipment costs Customer retention Less materials costs In-Home Wiring Has Been the Driver Re-use existing in home wiring for voice, data & video service Less labor and time inside the home Cross connect & bridge onto home wiring at side of home Minimized disruption Maintenance needs outside the premise Varying Technology Approaches 1. Have a broad ONT product
    [Show full text]
  • EOC-10A Gigabit Ethernet / CATV Over Coax Modem
    TDM Series - Ethernet over coaxial EOC-10A Gigabit Ethernet / CATV over Coax Modem The EOC-10A is point-to-point EoCNA (Ethernet over Coax Network Alliance) solution that efficiently extends 10/100/1000Mbps Ethernet circuits up to 700 meters (2,296feet) at full Fast Ethernet speed using existing coaxial cable. The EOC-10A will allow Ethernet connectivity in existing facilities or homes without pulling extra cable. This is perfect solution for Ethernet on the factory floor where systems have been upgraded from slower serial communication to Ethernet networking. Installation is easy with absolutely no settings required. The EOC-10A is used in Coaxial cable systems to extend Ethernet connectivity over existing CCD/CATV grade Coaxial cable. The EOC-10A works by sharing the same cable with CATV signals, without interference to the existing CATV signals. Features • Extends LAN connectivity using existing coaxial cable • Asymmetrical using EoCNA standard • Transmits CATV and Ethernet over the same coaxial cable • Operates transparently to high layer protocols such as TCP/IP • 192Mbps @ up to 700 meters (2,296feet) • Auto MDI / MDIX • 64Mbps @ 1.2Km (4,000feet) • Auto negotiation • Supports point to point • Plug and Play, no configuration required • Supports point to multi-point up to 8 nodes over tap/splitter • Status LEDs for simple monitoring Specifications Ethernet Interface Two 10/100/1000 Mbps, RJ45 Standards IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x Coax Interface Two F-Type Female Coax Connectors, One for Power Input 12VDC (via AC
    [Show full text]
  • Ethernet Over Coax Transceiver
    Ethernet over Coax Transceiver Operation Manual DA-EC1101R DA-EC1101T Powered by Before Using the Product FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. User’s Caution Statement Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Product Overview DA-EC1101R / DA-EC1101T is a networking device(EOC: Ethernet Over Coax) that uses coaxial cables. It makes it possible to supply Power over Ethernet and transmit data between a network camera that uses RJ45 port and a DVR using coaxial cables. 2 Product Features ● Makes it possible to install Full-HD network cameras using existing coaxial cables. ● 10/100Base-T two-way communication allows use of the product as a transmitter or a receiver.
    [Show full text]
  • Tl-Mc85 Ethernet Over Coax Adapter Disclaimer Copy Warning
    P a g e | 1 PRODUCT MODEL NUMBER: TL-MC85 ETHERNET OVER COAX ADAPTER ABOUT THIS MANUAL DISCLAIMER No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or damage of any kind resulting from the use of this document COPY WARNING This document includes some confidential information. Its usage is limited to the owners of the product that it is relevant to. It cannot be copied, modified, or translated in another language without prior written authorization from TRANSLITE GLOBAL LLC P a g e | 2 INDEX TABLE OF CONTENTS CHAPTER 1 BASIC ILLUSTRATION ........................................................................................... 3 1.1 CONNECT THE MOCA ADAPTER ............................................................................................ 3 1.2 INSTALLATION NOTES ........................................................................................................... 4 1.3 USUAL DEPLOYMENT METHODS ........................................................................................... 4 CHAPTER 2 INSTALLING THE MOCA ADAPTER .................................................................... 8 2.1 INSTALLATION ITEMS ............................................................................................................ 8 2.2 CONNECT TO THE DEVICE VIA WEB NMS ............................................................................
    [Show full text]
  • Product Guide
    VERACITY IP TRANSMISSION PRODUCT GUIDE www.veracityglobal.com PRODUCT GUIDE CONTENTS This Product Guide provides short-form information on all Veracity IP Transmission products and is ETHERNET OVER COAX HIGHWIRE 4 intended as a useful product comparison and product overview. ETHERNET EXTENDERS OUTREACH 8 A full datasheet for each product is available on the Veracity website www.veracityglobal.com LONG RANGE ETHERNET LONGSPAN 11 Each product has an example application diagram which illustrates how the product might be NETWORK SWITCHES + DEVICES LIGHTSPAN 14 connected. Further application diagrams can be TIMENET 14 found in the datasheets and on the website. Power CAMSWITCH 15 Over Ethernet is a core feature of most modern IP installations, so we have provided a useful reference INSTALLATION TOOLS POINTSOURCE 16 table on the right which shows the POE Classes, PINPOINT 16 IEEE standard, the power levels at the PSE (Power POE INJECTORS + POWER SUPPLIES OUTSOURCE 17 Sourcing Equipment) and the maximum power POWER SUPPLIES 18 which can be delivered at the PD (Powered Device). ACCESSORIES + SPARES 2 PIN POWER CORDS 19 For more information of POE and how it works, please visit our website. Use the Power Sources key on page 3, to know which sources can be used with each product, as indicated throughout the guide. IP Transmission Products Guide VUK DV4.5.2 © Veracity UK Ltd. All rights reserved. 2021 2 POE REFERENCE TABLE POE IEEE POE POWER POE POWER POWER SOURCES CLASS STANDARD AT PSE AT PD 0 802.3af 15.4W 12.95W 57V 800mA Power Supply 1 802.3af 4W 3.84W 57V 1500mA Power Supply 2 802.3af 7W 6.49W 3 802.3af 15.4W 12.95W 57V 100W POE Power Supply 4 802.3at 30W 25.5W 56V 240W POE Power Supply 5 802.3bt 45W 40W 6 802.3bt 60W 51W 57V 1U RACK 8800mA Power Supply 7 802.3bt 75W 62W 12V UNIVERSAL Power Supply 8 802.3bt 90W 71.3W PSE = Power Sourcing Equipment PD = Powered Device 24V RMPSU Power Supply 3 ETHERNET OVER COAX HIGHWIRE COAXETHERNET TOOVER 500MCOAX CONNECTION | ETHERNET DIAGRAM OVER COAX | Upgrade analogue to IP cameras - no recabling.
    [Show full text]
  • DOCSIS Mhav2 Technical Report
    Data-Over-Cable Service Interface Specifications DCA - MHAv2 Modular Headend Architecture v2 Technical Report CM-TR-MHAv2-V01-150615 RELEASED Notice This DOCSIS® technical report is the result of a cooperative effort undertaken at the direction of Cable Television Laboratories, Inc. for the benefit of the cable industry and its customers. You may download, copy, distribute, and reference the documents herein only for the purpose of developing products or services in accordance with such documents, and educational use. Except as granted by CableLabs® in a separate written license agreement, no license is granted to modify the documents herein (except via the Engineering Change process), or to use, copy, modify or distribute the documents for any other purpose. This document may contain references to other documents not owned or controlled by CableLabs. Use and understanding of this document may require access to such other documents. Designing, manufacturing, distributing, using, selling, or servicing products, or providing services, based on this document may require intellectual property licenses from third parties for technology referenced in this document. To the extent this document contains or refers to documents of third parties, you agree to abide by the terms of any licenses associated with such third-party documents, including open source licenses, if any. Cable Television Laboratories, Inc. 2014-2015 CM-TR-MHAv2-V01-150615 DCA - MHAv2 DISCLAIMER This document is furnished on an "AS IS" basis and neither CableLabs nor its members provides any representation or warranty, express or implied, regarding the accuracy, completeness, noninfringement, or fitness for a particular purpose of this document, or any document referenced herein.
    [Show full text]
  • Copyrighted Material
    4406c01.fm Page 1 Tuesday, March 15, 2005 2:09 AM Chapter Network 1 Fundamentals THE FOLLOWING NETWORK+ EXAM OBJEC- TIVES ARE COVERED IN THIS CHAPTER: 1.1 Recognize the following logical or physical network topologies given a diagram, schematic, or description: Star Bus Mesh Ring 1.2 Specify the main features of 802.2 (Logical Link Control), 802.3 (Ethernet), 802.5 (Token Ring), 802.11 (wireless), and Fiber Distributed Data Interface (FDDI) networking technologies, including: Speed Access method (CSMA/CA [Carrier Sense Multiple Access/Collision Avoidance] and CSMA/CD [Carrier Sense Multiple Access / Collision Detection]) Topology Media 1.3 Specify the characteristics (for example, speed, length, topology, and cable type) of the following cable standards: 10Base-T and 10Base-FL COPYRIGHTED 100Base-TX and MATERIAL 100Base-FX 1000Base-TX, 1000Base-CX, 1000Base-SX, and 1000BASE-LX 10GBase-SR, 10GBase-LR, and 10GBase-ER 1.4 Recognize the following media connectors and describe their uses: RJ-11 (Registered Jack) RJ-45 (Registered Jack) F-Type 4406c01.fm Page 2 Tuesday, March 15, 2005 2:09 AM ST (straight tip) SC (subscriber connector) IEEE1394 (FireWire) LC (local connector) MTRJ (Mechanical Transfer Registered Jack) USB (Universal Serial Bus) 1.5 Recognize the following media types and describe their uses: Category 3, 5, 5e, and 6 UTP (unshielded twisted-pair) STP (shielded twisted-pair) Coaxial cable SMF (single-mode fiber) optic cable MMF (multimode fiber) optic cable 1.6 Identify the purposes, features, and functions of the following network components: Hubs Switches Bridges Routers Gateways CSU/DSU (Channel Service Unit/Data Service Unit) NICs (network interface cards) ISDN (Integrated Services Digital Network) adapters WAPs (wireless access points) Modems Transceivers (media converters) Firewalls 3.2 Identify the basic capabilities needed for client workstations to connect to and use network resources (for example, media, network protocols, and peer and server services).
    [Show full text]
  • Instruction Manual Packaging Contents System
    Instruction Manual Gigabit Ethernet LAN Over Coaxial Extender Kit/Receiver - 2.4km EOC1110K / EOC1110R DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com JP: 取扱説明書 - jp.startech.com Packaging Contents SKU EOC1110K: • 2 x Ethernet over Coax converter box • 2 x Universal Power Adapter (NA/UK/EU/AU) SKU EOC1110R • 1 x Coax to Ethernet Media Receiver • 1 x Universal Power Adapter (NA/UK/EU/AU) • 1 x Instruction Manual System Requirements *actual product may vary from photos • 10/100/1000Mbps compatible Ethernet network/equipment • Coaxial cabling (RG-59/6/7/11) • Available AC power outlet at converter box locations Installation Cable Lengths Hardware Installation Maximum bandwidth (Mbps) based on coaxial cable type and length. NOTE: Both of the converter boxes in the EOC1110K kit are identical, RF Distance RG-59 RG-6 RG-7 RG-11 so they can be installed at either end, in any order. Bandwidth 1. At one of the locations for the converter box, connect an RJ45 100m ~ 700m 144 144 144 144 Ethernet cable from the existing Ethernet network or computer 800m 128 144 144 144 network adapter to the “LAN” port on the converter box. 900m 112 144 144 144 2. Connect the coax cable to the “Link” F-Connector on the converter. 1000m 96 128 144 144 OPTIONAL: If also transmitting analog cable TV signals over the coax line, connect the CATV F-Connector to a TV or TV receiver.
    [Show full text]
  • ETHERNET OVER COAX HIGHWIRE COAX to 500M | ETHERNET OVER COAX • Upgrade Analogue to IP Cameras - No Recabling
    www.veracityglobal.com ETHERNET OVER COAX HIGHWIRE COAX TO 500M | ETHERNET OVER COAX • Upgrade analogue to IP cameras - no recabling. IP CA HIG IRE™ • Uses legacy coaxial cabling. ME HW RA ETHERNET VHW-HW • Supports HD and 4K IP cameras. VHW-HW DATA ONLY • Fully transparent full-duplex 100Base-TX. NETWORK SWITCH COAXIAL VIDEO CABLE • Easy to install - no IP address or other setup. 300M ON RG59 500M ON RG11 • 500m on RG11 or up to 300m on RG59. POWER LOW VOLTAGE LOW VOLTAGE POWER POWER • 12-40V DC or 24V AC power input. ETHERNET WITH POE ETHERNET DATA ONLY • Non POE, local power required at camera. PRODUCT CODE VHW-HW Unit Size L:104mm W:54mm H:24mm POWER SOURCES POE OVER COAX (BASE & CAMERA) HIGHWIRE POWERSTAR COAX TO 500M | ETHERNET & POE OVER COAX • Upgrade analogue to IP cameras - no recabling. HIGHWIRE • Same as HIGHWIRE with POE over coax. IP CA POWERSTAR™ • POE switch powers HIGHWIRE Base unit, ME RA POE VHW-HWPS-B VHW-HWPS-C HIGHWIRE Camera unit and IP Camera. POE POE OVER COAX • For maximum range & power Veracity’s 57V POE NETWORK SWITCH COAXIAL VIDEO CABLE DC PSU can be used as alternative to POE in. • Up to 25W POE to IP camera with 57V DC PSU. POWER (Optional POWER) 300M ON RG59 500M ON RG11 PRODUCT CODES • SAFEVIEW™ Instant LED status confirmation. ETHERNET WITH POE ETHERNET DATA ONLY Base VHW-HWPS-B Camera VHW-HWPS-C Unit Size L:104mm W:54mm H:24mm POWER SOURCE 2 PORT POE OVER COAX (CAMERA) HIGHWIRE POWERSTAR DUO COAX TO 500M | ETHERNET & POE OVER COAX • Replace 1 analogue camera with 2 IP cameras HIGHWIRE without recabling.
    [Show full text]