Taco Bell, N of NEC Southern/Stapley, Mesa, AZ 1232 E

Design Review Project Narrative

Date: March 23, 2016 To: City of Mesa, Arizona Re: Taco Bell, N of NEC Southern/Stapley, Mesa, AZ 1232 E. Southern Ave., Mesa, AZ 85204

Overview This proposed Taco Bell project includes a new Taco Bell building on an existing vacant parcel of land facing Stapley Dr. that will be split-off from an existing larger parcel of land. The new Taco Bell restaurant includes a drive-thru lane, adequate parking, and landscaping per the City of Mesa requirements.

This project is located North of the Northeast corner of Southern Ave./Stapley Dr. in Mesa, AZ. The Assessor Parcel Number (APN) for this project is 139-05-004k and the existing Zoning is LC Limited Commercial. No zoning changes are planned or required for this project.

Pre-Submittal Conference A Pre-Submittal Conference was held with the City of Mesa Planning and Engineering staff, on Monday, February 22, 2016, at 10:30 AM, in the Sagebrush Conference Room on the 2nd Floor of the City of Mesa Municipal Building, 55 N. Center St., Mesa, AZ 85201.

Typical Business Operation Taco Bell operates as a quick-service restaurant that includes indoor dining and drive-thru service along with supporting kitchen, storage, and restroom areas. As a drive-thru restaurant, the proposed Taco Bell is a use that is typically found in LC Limited Commercial zoned areas in the City of Mesa. In addition, the existing land parcels on all four sides of the proposed Taco Bell are all zoned LC Limited Commercial.

Hours of Operation Taco Bell Hours of Operation will be 7 AM to Midnight Sunday thru Thursday and 7 AM to 2 AM Friday and Saturday. This will not be a 24 hour operation.

Parking and Access The proposed Taco Bell site is large enough to contain the required city of Mesa, and Taco Bell standard, parking requirements, and includes the trash enclosure and surface retention area. The existing Panda Express has allowed for a future connection to this parcel, and the Site Plan has provided for a connection to the existing drive stub. In addition, there will be a new curb cut

driveway access off Stapley Rd. and a drive/parking aisle will be placed across the front of the Taco Bell site to connect the existing driveway to the north with the Panda Express to the south. Access to the remaining vacant parcel to the east will be through the existing drive to the north of Taco Bell and the new drive through the south side of the Taco Bell site.

Dedications and Site Reductions The City of Mesa has planned for Stapley Rd. to be expanded in the near future. Taco bell will be dedicating approx. 45 feet of street frontage to allow for this (depth varies). The proposed future street design has been shown on the Taco Bell site plan. In addition, the remaining vacant parcel to the east will have a 25’ wide “frontage” that is trimmed from the north portion of the proposed Taco Bell site. This “frontage” is wide enough for the existing 15 foot wide ingress easement, a future five foot sidewalk connection, and allow for signage at the street.

Proposed Architecture The proposed Taco Bell building architecture will consist of various shades of painted stucco/EIFS and include a cultured stone corner pop-up with a decorative slat wall on three sides over the Dining Room windows. The building parapet height will vary and step down from west (Dining Room side) to east (service side). A drive-thru pick-up window cover, over the drive-thru lane, has been added at the request of Mesa Planning staff at the Pre-Submittal Conference. The drive-thru cover uses the lower slat wall valance element to tie it into the building architecture.

Stipulation Modification Site Plan Review case 82-1 (SPR82-1) was created when the medical building to the north of the Taco Bell was planned, and was approved with stipulations. SPR82-1 approval stipulation 4 states “a subdivision plat be filed before parcelization takes place”. Since the 1982 approval, the medical building was split from the overall 1982 parcel, constructed, and later added onto, and two retail buildings were built along Southern Ave., all without the plat process occurring. We are requesting that SPR82-1, Stipulation 4, be deleted as part of this application.

Development Timing Since this is an existing vacant parcel of land, with existing utilities in the area, Taco Bell development will begin shortly after Design Review/Site Plan approvals, and Building Permit Plan Review has been completed. Taco Bell proposes to be in operation by the end of 2016.

We believe that this project is consistent with the nature of the area and believe that this development will be a positive amenity to the residents of the surrounding area.

Sincerely, JD Berryman Looker & Cappello Architects, Inc.

TEMPE, ARIZONA 85282

480-730-1776

FAX: 480-968-6571

SOUTH ELEVATION 3/16" = 1'-0" A

EAST ELEVATION 3/16" = 1'-0" C WEST ELEVATION 3/16" = 1'-0" B

CONTRACT DATE: 01-25-16 BUILDING TYPE: LIVE MAS LARGE 50 PLAN VERSION: NOVEMBER 2015 SITE NUMBER: - STORE NUMBER: -

TACO BELL

SOUTHERN/STAPLEY MESA, ARIZONA 85204

LIVE MAS LARGE 50 EXTERIOR COLOR ELEVATIONS NOTE: SIGNAGE SHOWN FOR INFORMATION ONLY. ALL SIGNAGE UNDER SEPARATE REVIEW AND PERMIT. A4.0C

PLOT DATE: 03-22-16 NORTH ELEVATION 3/16" = 1'-0" D

LC1024 COLOR AND MATERIAL SHEET N OF NEC SOUTHERN/ STAPLEY MESA, AZ 85204

PAINT ACCENT PAINT PAINT SHERWIN WILLIAMS (BEHIND SLAT WALL AND SHERWIN WILLIAMS SW6122 AT REAR PARAPET TOP) SW2823 'CAMELBACK' SHERWIN WILLIAMS 'ROOKWOOD CLAY' SW6831 'CLEMATIS'

PAINT ACCENT PAINT CULTURED STONE METAL EYEBROW/CANOPY PARAPET CAP CORONADO SHERWIN WILLIAMS SHERWIN WILLIAMS IDAHO DRY STACK SW7034 SW7069 "CARMEL MOUNTAIN" 'STATUS BRONZE' 'IRON ORE'

STOREFRONT BOLLARDS KAWNEER DARK BRONZE DOT YELLOW (SIMILAR TO COLOR 5) Wet

Night Hawk

Description Outdoor Decorative LED Emergency Light

Housing Durable and Vandal Resistant Die-Cast Aluminum Housing with 1/2” Coin Plug for Conduit. Includes Integrated Photocell, Switchable Between Photocell or Wall Switch Control. Low Proﬁle, ADA Compliant.

Lens UV-Resistant Polycarbonate Lens

Reﬂectors Mirrored Reﬂector

Battery Backup NiCad Battery Backup (4.8V, 2.8A) Supplies 90 Minutes of Emergency Operation. Self-Test/Self Diagnostics Included. Low-Voltage Battery Disconnection Prevents Deep Battery Discharge Damage. HITE NH-3008 | W 24 Hour Recharge After 90 Minute Discharge.

Mounting Wall or Ceiling Mount Over a Recessed Junction Box or Use Surface Conduit.

LED Module Luminous Flux 1050, CRI: 75 CCT: 5000K, 50,000 Hours

Wattage LED: 11w (14 System Watts)

Driver Input Voltage: 120/277V

Listing & Ratings UL: Listed for Wet Locations (IP65)

NH-3009 | BRONZE Custom Colors Available on Request.

3 ECOLOGYLIGHTING.COM Catalog WST LED Number

Architectural Wall Sconce Notes

Type

Hit the Tab key or mouse over the page to see all interactive elements. Introduction The classic Architectural Wall Sconce is now Inverted available with WLU option only. available with the latest in LED technology. The result is a long-life, maintenance-free product with Specifications typical energy savings of 75% compared to metal Luminaire Optional Back Box (BBW) halide versions. The integral battery backup option Height: 7-1/4” Height: 4” (18.4 cm) (10.2 cm) provides emergency egress lighting, without the use of a back-box or remote gear, so installations Width: 16-1/4” Width: 5-1/2” (41.3 cm) (14.0 cm) maintain their aesthetic integrity. Depth: 9-1/8” Depth: 1-1/2” (23.2 cm) WALL SCONCE(3.8 BBWWALL (Backcm) SCONCE Box BBWWall) (Back MOUNTING Box Wall) MOUNTING The WST LED is ideal for replacing existing 50 –

Weight: 17 lbs For 3/4” NPT 175W metal halide wall-mounted products. The 1-1/2 (7.7 kg) W5-1/2 5-1/2 1-1/2 D side-entry expected service life is 20+ years of nighttime use. conduit H H4 4 W D

Ordering Information EXAMPLE: WST LED 2 10A700/40K SR3 MVOLT DDBTXD

WST LED

Performance 3 Finish (required) Series Light Engines Package Distribution Voltage Mounting Options

WST LED 1 One engine 700 mA options: SR2 Type II MVOLT 1 Shipped included Shipped installed DDBXD Dark bronze (10 LEDs) 10A700/30K 3000K SR3 Type III 120 1 (blank) Surface mount PE Photoelectric cell, button type 4, 5 DBLXD Black 2 Two engines 10A700/40K 4000K SR4 Type IV 208 1 Shipped separately 2 SF Single fuse (120, 277, 347V) 4 DNAXD Natural aluminum 4 (20 LEDs) 10A700/50K 5000K 240 1 BBW Surface-mounted DF Double fuse (208, 240, 480V) DWHXD White 277 1 back box DMG 0-10V dimming driver (no controls) DSSXD Sandstone UT5 Uptilt 5 degrees ELCW Emergency battery backup 6 DDBTXD Textured dark bronze 347 WLU Wet location door for up orientation 7 DBLBXD Textured black 480 PIR Motion/ambient light sensor 8 DNATXD Textured natural aluminum DS Dual switching 9 DWHGXD Textured white Shipped separately DSSTXD Textured sandstone VG Vandal guard WG Wire guard

NOTES 1 MVOLT driver operates on any line voltage from 120-277V (50/60 Hz). Emergency Battery Operation Specify 120, 208, 240 or 277 options only when ordering with photocell (PE), fusing (SF, DF), or dual switching (DS). The emergency battery backup (ELCW option) is integral to the luminaire - no external housing required! This design 2 May also be ordered separately as an accessory. Ex: WSBBW DDBXD U. provides reliable emergency operation while maintaining the aesthetics of the product. Must specify finish. All ELCW configurations include an independent secondary driver with an integral relay to immediately detect 3 Must be ordered with fixture; cannot be field installed. AC power loss. Dual light engines are wired in parallel so both engines operate in emergency mode and provide 4 Not available with MVOLT option. Button photocell (PE) can be ordered additional component redundancy. These design features meet various interpretations of NFPA 70/NEC 2008 - with a dedicated voltage option. Single fuse (SF) requires 120, 277 or 347 700.16 voltage option. Double fuse (DF) requires 208, 240 or 480 voltage option. The emergency battery will power the luminaire for a minimum duration of 90 minutes (maximum duration of three 5 Not available with 480V option. Not available with motion/ambient light hours) from the time supply power is lost, per International Building Code Section 1006 and NFPA 101 Life Safety sensor (PIR). Code Section 7.9, provided luminaires are mounted at an appropriate height and illuminate an open space with no 6 Integral battery pack is rated for -20° to 60°C operating temperature. major obstructions. ELCW warranty is 3-year period. Not available with 347V or 480V. Not available with WLU. The examples below show illuminance of 1 fc average and 0.1 fc minimum of the single-engine Type IV product in 7 WLU not available with PIR or ELCW. emergency mode. 8’ MH 12’ MH 8 Specifies the SensorSwitch SFOD-7-ODP control (photocell included); see Motion Sensor Guide for details. Includes ambient light sensor. Not available with “PE” option (button type photocell). Dimming driver WST LED 1 10A700/40K SR4 standard. Not available with WLU, VG or WG. MVOLT ELCW 9 Provides 50/50 luminaire operation via two independent drivers and light 10’ x 10’ Gridlines engines on two separate circuits. Not available with one engine, MVOLT, 8’ and 12’ Mounting Height ELCW, WLU, SF, or DF. Must specify voltage; voltage must be the same for both drivers. When ordered with photocell (PE) or motion sensor (PIR), only the primary power source leads will be controlled.

One Lithonia Way • Conyers, Georgia 30012 • Phone: 800.279.8041 • Fax: 770.918.1209 • www.lithonia.com WST-LED © 2011-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/11/15 Performance Data Lumen Output Lumen Ambient Temperature (LAT) Multipliers Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative Use these factors to determine relative lumen output for average ambient temperatures of the configurations shown, within the tolerances allowed by Lighting Facts. from 0-40°C (32-104°F). Ambient Lumen Multiplier 40K 0°C 32°F 1.10 Drive System 10°C 50°F 1.06 Light Performance Dist. (4000K, 70 CRI) Current Watts 20°C 68°F 1.02 Engines Package 1 Type Nominal (mA) (MVOLT ) B U G LPW 25°C 77°F 1.00 Lumens 30°C 86°F 0.98 SR2 2,005 1 0 1 84 1 40°C 104°F 0.92 700 10A700/--K 24W SR3 2,029 1 0 1 84 (10 LEDs) SR4 1,959 1 0 1 82 SR2 3,944 1 0 1 84 2 Projected LED Lumen Maintenance 700 10A700/--K 47W SR3 4,028 1 0 1 86 (20 LEDs) Data references the extrapolated performance projections for the WST LED 2 10A700 SR4 3,851 1 0 1 82 platform in a 25°C ambient, based on 10,000 hours of LED testing (tested per IESNA LM- 80-08 and projected per IESNA TM-21-11). 1 See electrical load chart for 347/480V system watts. To calculate LLF, use the lumen maintenance factor that corresponds to the desired number of operating hours below. For other lumen maintenance values, contact factory.

Operating Hours 0 25,000 50,000 100,000

Lumen Maintenance Factor 1.0 0.94 0.88 0.77

Electrical Load Current (A) Light Drive Current System Engines (mA) Watts 120 208 240 277 347 480 24W 0.24 0.14 0.12 0.1 - - 1 700 29W 1 - - - - 0.09 0.07

47W 0.44 0.27 0.23 0.20 - - 2 700 53W 1 - - - - 0.17 0.12 1 Higher wattage is due to electrical losses from step-down transformer.

Photometric Diagrams To see complete photometric reports or download .ies files for this product, visit Lithonia Lighting’sWST LED homepage.

Isofootcandle plots for the WST LED 2 10A700/40K SR2, SR3, and SR4. Distances are in units of mounting height (12’). Distribution overlay comparison to 175W metal halide.

4 3 2 1 0 1 2 3 4 4 3 2 1 0 1 2 3 4 4 3 2 1 0 1 2 3 4 LEGEND LEGEND 4 4 4 0.1 fc WST 3 3 3 LED,

0.5 fc 2 2 2 0.5 fc

1 1 1 WST 1.0 fc HID, 0 0 0 0.5 fc -1 -1 -1 10’ W Sidewalk -2 -2 -2 LLDs: WST HID: WST LED: -3 -3 -3 WST HID = 0.72 213W 47W SR2 SR3 SR4 WST LED = 0.95 -4 -4 -4 WST LED 2 10A700 40K SR4, Test No. 2489033-4 tested in accordance with No. 2489033-4 tested in accordance Test IESNA LM-79-08. Test No. 2489033-6 tested in accordance with No. 2489033-6 tested in accordance Test IESNA LM-79-08. Test No. 2489033-5 tested in accordance with No. 2489033-5 tested in accordance Test IESNA LM-79-08. WST 175M FT Probe, 12’ Mounting Ht

FEATURES & SPECIFICATIONS 250 x 100' building INTENDED USE ELECTRICAL 10' sidewalk The classic architectural shape of the WST LED was designed for applications such as hospitals, Light engine(s) consist of 10 high-efficacy LEDs mounted to a metal core circuit board and led 1 sr3 ELCW plan view 8' mtg ht over door schools, malls, restaurants, and commercial buildings. The long life LEDs and driver make this integral aluminum heat sinks to maximize heat dissipation and promote long life (100,000 Scale 1" = 40' luminaire nearly maintenance-free. hrs at 25°C, L77). Class 2 electronic driver has a power factor >90%, THD <20%. Easily- contours at 1.0 fc (red) 0.5 fc (blue) on grade serviceable surge protection device meets a minimum Category B (per ANSI/IEEE C62.41.2). CONSTRUCTION The single-piece die-cast aluminum housing integrates secondary heat sinks to optimize thermal INSTALLATIONCalculated values include direct and interreflected components. transfer from the internal light engine heat sinks and promote long life. The driver is mounted in A universal mounting plate with integral mounting support arms allows the fixture to hinge direct contact with the casting for a low operating temperature and long life. The die-cast door down for easy access while making wiring connections. frame is fully gasketed with a one-piece solid silicone gasket to keep out moisture and dust, providing an IP65 rating for the luminaire. LISTINGS CSA certified to U.S. and Canadian standards. Light engines are IP66 rated; luminaire is IP65 FINISH rated and suitable for wet locations when mounted with the lenses down. WLU option offers Exterior parts are protected by a zinc-infused Super Durable TGIC thermoset powder coat finish wet location listing in “up”orientation. Rated for -30°C minimum ambient. that provides superior resistance to corrosion and weathering. A tightly controlled multi-stage process ensures a minimum 3 mils thickness for a finish that can withstand extreme climate DesignLights Consortium® (DLC) qualified product. Not all versions of this product may changes without cracking or peeling. Standard Super Durable colors include dark bronze, black, be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org to natural aluminum, sandstone and white. Available in textured and non-textured finishes. confirm which versions are qualified. OPTICS WARRANTY Precision-molded acrylic lenses are engineered for superior distribution, uniformity, and spacing Five year limited warranty. Full warranty terms located at www.acuitybrands.com/ in wall-mount applications. Light engines are 4000K (70 CRI). The WST LED has zero uplight and CustomerResources/Terms_and_conditions.aspx. qualifies as a Nighttime Friendly™ product, meaning it is consistent with the LEED® and Green Globes™ criteria for eliminating wasteful uplight. Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.

One Lithonia Way • Conyers, Georgia 30012 • Phone: 800.279.8041 • Fax: 770.918.1209 • www.lithonia.com WST-LED © 2011-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/11/15 Features and Beneﬁts • Batwing beam pattern to increase light coverage • Waterproof IP68 rating • UL certified for use in wet, damp and dry locations • UV resistant, suitable for direct sun exposure • Operating temperature range from -40°C to +60°C (-40°F to +140°F) • Constant current driven LEDs • No UV or IR emission • Complies with FCC Title 47, Part 15, Subpart B for Class A digital devices • 5-year limited warranty

Applications • Channel Letters • Cabinet Signs • Cloud Signs • Cove Lighting • Accent Lighting

Ordering Information Ordering Code LED Color/ Number of Input Nominal Max. Wattage Nominal Light CCT (K) Modules Voltage Current per Module* Output (lm)* per Foot per Meter (Volt) (A/Module) (W) per Foot per Meter LS-APEX-ASW-G2 AgiLight SignWhite 2 6.56 12 0.100 1.24 250 820 LS-APEX-65K-G2 White/6500K 2 6.56 12 0.100 1.24 250 820 LS-APEX-57K-G2 White/5700K 2 6.56 12 0.100 1.24 250 820 LS-APEX-50K-G2 White/5000K 2 6.56 12 0.100 1.24 250 820 LS-APEX-45K-G2 White/4500K 2 6.56 12 0.100 1.24 210 689 LS-APEX-41K-G2 White/4100K 2 6.56 12 0.100 1.24 210 689 LS-APEX-30K-G2 White/3000K 2 6.56 12 0.100 1.24 210 689 LS-APEX-27K-G2 White/2700K 2 6.56 12 0.100 1.24 210 689 LS-APEX-24K-G2 White/2400K 2 6.56 12 0.100 1.24 180 590 *Nominal 1.20W *±10%

Ordering Guide Color Temperature Scale 2700K 3000K LED Sign Model Color Temperature Beam Pattern 4500K 5000K 5700K 6500K ASW 2400K 4100K LS -APEX -65K -G2 6500K G2: Batwing Warm White Bright White Daylight 3200K 4500K 6000K 8000K

General LED, Inc. General LED Fze 1074 Arion Circle, Suite 116 822, Building 4EA San Antonio, TX 78216 Dubai Airport Free Zone United States of America Dubai, United Arab Emirates +1.866.482.0203 +971 4 7017901

AgiLight®, Inc., a Division of General LED, Inc. +1.866.482.0203 www.AgiLight.com © 2015 General LED, Inc. 2015 All rights reserved. www.GeneralLED.com Product Specifications subject to change without notice. 07- 2015 G2 Batwing Beam Pattern

Power Supply Load Chart STANDARD (ft) METRIC (m) Model 12W 60W 12W 60W LS-APEX-XXX-G2 4 24 1.2 7.3

Wire Gauge Chart MAXIMUM DISTANCE* Wire Gauge (AWG) STANDARD (ft) METRIC (m) 26 3 0.9 Population Density Guide 24 4 1.2 STANDARD (in) 22 7 2.1 Channel Depth: 3 4 5 6 8 20 11 3.4 Max. Stroke * * 13 17 20 18 18 5.5 Multiple Row Spacing * * 12 15 17 16 29 8.8 14 45 13.7 METRIC (mm) 12 71 21.6 Channel Depth: 125 150 200 75 100 10 120 36.6 Max. Stroke 330 432 508 * * *Distance from power supply to load (at full capacity) Multiple Row Spacing * * 305 381 432 * Please contact a sales associate LED Module Dimensions

0.80in 0.45in 20.32mm 11.43mm

3.60in 2.40in 91.44mm 60.96mm

6.00in 152.4mm

Shipping Information STANDARD METRIC SKU Tray Box Case Case Box Case SKU Tray Box Case Case Box Case Model (ft) Quantity Quantity Quantity Weight Dimensions Dimensions (m) Quantity Quantity Quantity Weight Dimensions Dimensions SKUs (ft) SKUs (ft) SKUs (ft) (lb) (in) (in) SKUs (m) SKUs (m) SKUs (m) (kg) (mm) (mm) W D H W D H W D H W D H LS-APEX-XXX-G2 1 25 100 500 48 19.7 11.2 4.5 26.4 20.5 12.2 0.3 7.6 30.5 152.4 21.8 500 285 115 670 520 310

1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. Not suitable for submersed applications. 5. These products may be secured in place in the end product by any means available. CAUTIONS

Decorative Lighting PROJECT: Taco Bell

Type TB

3865 Produce Rd Suite 208 Louisville, KY 40218 Toll Free: 877-707-7378 Phone: 502-961-0096 Fax: 502-961-0357 Web: www.accu-serv.com

Item # 05247-051 / 05247-052

Classification: Up / Down (2) light Wet location wall mounted cylinder with top cap

Dimensions: Diameter - 6" Height - 18" Depth - 8 7/8"

Finish: Bronze

Lamp Type: (2) 18w PAR38 LED E # - E52809190 Location Exterior Lamp Type: Leadtime TBD RR6 Six-Inch Retrofit Housing

Product Description RR6 The RR6 recessed housing is designed to accommodate all Cree six-inch downlights in retrofit applications. It is rated for use with luminaires that consume low energy, such as the LR6 and CR6, optimizing energy density calculations for easier energy code compliance and LEED certification. The RR6 housing is IC rated, airtight, inherently protected and, when ordered with a GU24 socket, California Title-24 compliant.

Product Specifications

CONSTRUCTION & MATERIALS

Recessed retrofit housing accommodates Cree six-inch LED downlights in ceiling thickness from 0.25” to 1.25”.

Gasketed housing enables air-tight fit to effectively isolate housing assembly from conditioned space below.

Suitable for insulated or non-insulated ceilings.

Dimensions: L 12.5” x W 6.625” x H 7.5”

REGULATORY & VOLUNTARY QUALIFICATIONS

cULus Listed

IC air-tight rated, tested in accordance with ASTM E283.

Title-24 compliant when utilized with GU24 socket. 7.5”

Suitable for damp locations.

Compatible Downlights 12.5” RR6

CR6 Series

LR6 Series

LE6 Series 6.625”

Ordering Information Example: RR6

Product

RR6 120V, Edison Socket

RR6-GU24 120V, GU24 Socket

RR6-277V 277V, Connector

© 2013 Cree, Inc. All rights reserved. For informational purposes Rev. Date 05/21/2013 only. See www.cree.com/patents for patents that cover these products. Cree®, and the Cree logo are registered trademarks of Cree, Inc. www.cree.com/lighting T (800) 236-6800 F (262) 504-5415