Combo Heat Press

NODE 2001

Introduction

①：Clamp&Handle

②：Lifting switch

③：Aerial plug

④：Turning wheel

⑤：Route switch

⑥：Control Panel

⑦：Off/On Switch

⑧：Power plug

Installation

Step 1: Install connectors

There are two connectors, connector “1” is to Note: There is a slot in the connector Aiming at the slot, insert the connectors into connecting with route switch; connector “2” relevant socket is to conenectiong with heating pad

Screw the screw till it’s firm

Step 2：How to offload the heat platen from the main body.

1) Offload the up-heat platen

Move out the connector ”2” Draw down the handle Let the handle down freely

Screw the nail under the handle Get off the nail and draw up the handle then counter-clockwise you can release the up-heat platen

2) Offload the down-heat platen

Screw off the 4 screw caps in the base, bring up the down-platen then the down-platen is offloaded

Step 3: Install Plate press attachment

Aerial plug facing in, heating platen facing down Lock the screw cap in order to fix the plate pad Plug aerial plug on the plate pad assemble the up-platen to socket “2”

Screw the screw cap tightly , then you can use the Plate Press

Step 4: Install Cap press attachment

Let the longer end of bottom base face front, Add the iron slice and iron circle onto the screws Lock the srew caps. Aim at the whorl and place it on the machine

Let the end with wire of the cap Adjust the heat platen to right place, pull down Lock the screw caps heat platen face in, Aim at the the handle and press heat platen tightly slot and push it till the end

Plug aerial plug of cap heat element into socket “2” Screw the screw cap tightly , then you can use the Cap Press

Step 5: Install Mug Press attachment

Move out the two connectors Insert the two connectors “1” & “2” into relative socket Screw the screw cap tighty, then you can use the Mug Press Operation Process The operation of the control panel 1. Set temperature required

Turn on power switch, Select with arrows temperature required (normally 180℃) Temperature light – ON Left arrow select up. Right arrow select down

2. Set time required

Press OK button after temperature set, Select with arrows temperature required The Unit is second now timer light-ON Left arrow select up. Right arrow select down time range :0-180seconds

Printing methods: A) Mug Press: Put the mug in the machine, adjust pressure through screws, take the mug out, switch on the machine and set temperature and time required. Once the temperature rise to the required temperature, the buzzer will send out a short sound. Then put the mug with the picture in the machine, draw down the handle, the machine starts to count the time auotmatically. When time is up, the buzzer send out sound, take out the mug, job finished.

B) Cap/Plate/Plain Heat press： Bring up the parts of heat and fix the related heat platen.Place the object (i.e. Cap,Plate,T-shirt) on press bed, adjust pressure to your requirement, and turn on the power switch ON, The temperature starts to rise, once the temperature rise to the required temperature, the buzzer will send out a short sound. Then press object. Push the OK button once, wait for long buzzer sound, turn off the power switch, work finish and take out object.

Time and Temperature Parameter for Various Transfer Media

Serial Product Temperature Time (second) Notice No. Name (degree) 1. Choose “Mirror Effect” when pictures; 2. Adjust Moderate Pressure; 3. Make sure transfer and mug are tightly 30sec(first) attached; 1 Coated Mug 170-190 120sec(secomd) 4. Adjust suitable height of the mug inside the mug heater. 5. Put the Mug inside the mug heater before starting the temperature;

1. Choose “Mirror Effect” when printing pictures; 2. Flatly place the coated plate above silicon pad; 3. Make sure pressure is not excessive; 2 Coated Plate 180 120sec 3. Start to press the plate when the temperature reached 180 degree;

1. Choose “Mirror Effect” when printing pictures; 2. Adjust Moderate Pressure; 3. Firstly put the paper with picture on the silicon pad, then place the ceramic tile above it; Ceramic Tile 3 180 120sec 4. Make sure transfer paper and ceramic tile are ( & sublimation ink) attached well; 5. The picture is suggested to be placed in landscape orientation;

1. Choose “Mirror Effect” when printing pictures; 2. Tear off the surface film before transferring. 3. Make sure transfer paper and Pearlite Plate are 4 Key Chains & Pearlite Plate 180 100-120 attached well; 4. The picture is suggested to be placed in landscape orientation. Serial Product Temperature Time (second) Notice No. Name (degree) 1. It is suitable for T-shirt with 75%-100% cotton 2. Choose “Mirror Effect” when printing pictures; T-shirt 3. Adjust higher pressure for T-shirt Transfer; (Using dye Ink with Light or 5 180-190 30sec 4. After transferring, tear the transfer paper off Dark Paper) T-shirt immediately (Note: this method is more

suitable for cotton cloth)

1. Suitable for Cloth without cotton, T-shirt 2. Choose “Mirror Effect” when printing pictures; (Using sublimation Ink with Light 3. With more pressure (Note: Only suitable for 6 180-185 90sec or Dark new zealand Transfer cloth with no cotton content, such as Silk, Paper) Terylene etc.)

1. Transfer Image should be at right size Mirror (Pearlite plate) 7 180 120sec 2. Choosing “Mirror Effect” when printing (Inkjet paper & sublimation ink) 3. With more pressure

1. Transfer Image should be at right size CD case (Pearlite plate) 8 180 120sec 2. Choosing “Mirror Effect” when printing (Inkjet paper & sublimation ink) 3. With more pressure Double-side cigarette case 1. Transfer Image should be at right size 9 (Pearlite plate) 180 120sec 2. Choosing “Mirror Effect” when printing (Inkjet paper & sublimation ink) 3. With more pressure 1. Double side transferable; 2. Choosing “Mirror Effect” when printing Sublimation Lighter 3. With moderate pressure 10 180 120sec (Inkjet paper & sublimation ink) 4. The size of paper should right cover the lighter. The picture side should face the silicon pad (Reverse Transferring) 1. Transfer Image should be at right size Jigsaw Puzzle 11 180 90sec 2. Choosing “Mirror Effect” when printing (Inkjet paper & sublimation ink) 3. With more pressure

1. Keep the picture height within 10 cm. Space bottle 2. With less pressure 12 180 120sec (Inkjet paper & sublimation ink) 3.Keep the cap of bottle open when transferring. 4. Choosing “Mirror Effect” when printing 1. Keep the picture height within 4.5 cm. Coffee mug 13 180 30 2. Hang the mug in the middle of mug heater when (Inkjet paper & sublimation ink) transferring 14 Metal Tags & Key Rings 180 120 1. Pay attention to the definition of the picture. Serial Product Temperature Time (second) Notice No. Name (degree) (Double-side transferable) 2. Transfer pictures on both sides at the same time. (Inkjet paper & sublimation ink) 3. With more pressure. 4. Choosing “Mirror Effect” when printing 1. Keep the picture within the transferable size. 2. Pay attention to keeping the part which can not resist Wallet (Waist pack) 15 180 120 to high temperature away from the heating pad. (Inkjet paper & sublimation ink) 3. With more pressure

1. Pay attention to keeping the part which can not Pillowcase 16 180 120-140 resist to high temperature away from the heating pad. (Inkjet paper & sublimation ink) 2. With more pressure 1. Take out the wood before transferring. Keep the Newsstand part which can not resist to high temperature away 17 180 120 (Inkjet paper & sublimation ink) from the heating pad. 2. With more pressure

Remarks:

The above parameter is only suitable for made by our company. Please do not apply it to other machines because different companies have different design for machines.

Besides, the above time and temperature are only suggested parameter. You could adjust the time and temperature during operation by yourself for better effect.

Technical Specification :

Voltage：110/220V Temperature range：0-250℃ Time range：0-3minute Packing Size：51*49*45CM Weight：33.05KG

Trouble shooting for transfer quality : A. If the color is pale: the temperature is too low / the pressure is not correct / or not pressed long enough. B. If the picture is blurring: Too much tranfer time causes proliferation. C. If the picture is not brilliant: Too much pressure or the temperature is too high. D. If a part of picture is blurring: Heat was not distributed correctly through heat plate. Allow more time between press operations. Pressure distribution can also be the cause, which can be set on the four plate surface adjusters. Please note that it has been factory set and there should be no need to adjust them E. If the pattern is scarred: Transfer time is too long. F. The pattern of color is different: the pressure is not correct or the transfer paper is poor quality G. Adhesive paper: the temperature is too high or poor printing ink Maintenance:

Ⅰ. No action after switch on the power 1. Check the plug whether it touchs well 2. Check the fuse whether it have been burn out. 3. Check the lead wire of the switch whether it have been fallen

Ⅱ. The display screen are working well, but the no temperature increasing on the Silica Gel Board 1. Check whether the tie-in of the Silica Gel touches well. 2. Check the 3,4 on PCB in the back whether it touches well.

Ⅲ. The display screen is un-normal, but the Silica Gel heats. Maybe for the fault of the PCB

Ⅳ. The display screen and Silica Gel works well, but un-normal show of the temperature. 1. Check whether the tie-in of the Silica Gel touches well. 2. Check the 5, 6 on PCB in the back box whether it touches well.

Advise: 1. Because the material and the thickness of the clothing are different, the temperature and the time are different too. 2. The temperature and the time are only for reference. And pls first try a sample to adjust the best temperature and time. 3. The best setting temperature are 180℃, pls do not over 220℃, and the transferring time should be within 3 minutes. 4. To make sure that the circuit can bear high-power machine, or it will bring about faulty of the fuse etc.