360 Motherboard Headers and Connector

Version 1.4 Disclaimer

The information contained in this document was obtained from the public domain and/or my own reverse engineering and is provided in good faith but no warranty can be made for its accuracy. Any opinions expressed are entirely those of myself and cannot be taken to represent the views of past, present or future employers.

I do not support piracy or the illegal copying of copyright material. I'm only seeking the ability to run custom software and push the hardware to it's maximum potential. Remember that a profitable game industry will guarantee us all amazing products for the future.

If you notice something incorrect or have any comment, please feel free to contact me.

Speedy22 [email protected] Introduction

Most of the information was based on the top and bottom layers of a dechipped 360 motherboard and decapped chips, I will update the information once I gain full knowledge of the inner layers of the motherboard. For reference, I have also included some information I have gathered from images of Development Hardware and XDK hardware found on the net. Please double-check my information, I am human and I do make mistakes. I have also attempted to give credit where credit was due. If you find any errors or omissions, please let me know so that I can correct it on future versions. Like most, I am doing this as a hobby in my spare time, so I will do my best to keep the information up to date but I can not make any guarantees.

I am currently looking for a supplier/manufacturer for the following components;

Controller Headset Port Both the Male and Female Connector.

Memory Card Port Male Connector (On Memory Card)

RF Module Port Male Connector (On RF Module)

Hard Drive Port Male Connector (On Hard Drive)

My current employment position will be changing in the near future, so I will be open for new opportunities. I am a Canadian citizen living in Waterloo, ON, Canada with a background in Electronics Engineering and Management. Feel free to contact me for more details.

Speedy22 [email protected] Table of Content

Motherboard Block Diagram ...... 2 J1A1 ...... 3 J2A1 ...... 4 J3A1 ...... 5 J9A1 ...... 6 J9A2 ...... 7 J2B1 ...... 8 J1C1 ...... 9 J5C1 ...... 10 J5C2 ...... 11 J8C1 ...... 12 J1D1 ...... 13 J1D2 ...... 14 J2D1 ...... 15 J2D2 ...... 16 J1E1 ...... 17 J1F1 ...... 18 J7F1 ...... 19 J3G1 ...... 20 J6G1 ...... 21 J7G1 ...... 22 J7G2 ...... 23 J9G1 ...... 24 Appendix Document Changes ...... 25 Unique per Console Numbers ...... 26 Retail Motherboard Differences ...... 27 Dashboard Updates ...... 28 System Requirements ...... 29 Retail Block Diagram ...... 30 XeDK Block Diagram ...... 31 HDK Block Diagram ...... 32 Memory Map ...... 33 CPU Pinout (BGAout) ...... 34 GPU Pinout (BGAout) ...... 35 Southbridge Pinout (BGAout)...... 36 Detailed Motherboard Block Diagram

Not in this Public Release

2 J1A1 10/100 Base-T Ethernet and USB Port

1 Green LED 9 RD+ 2 Green LED 10 CT 3 Yellow LED 11 RD- 4 Yellow LED 12 +5 VDC 5 TD+ 13 Data - 6 CT 14 Data + 7 TD- 15 GND 8 Shield GND 16 Pin 9 J6G1

Manufacturer: Bel Stewart Connectors Product Name and #: Magjack SI-80039-F

Notes:

Green and Yellow LEDs are not present, but all the connection are available on the 360 Motherboard. (Version 11)

LEDs are present on the 360's XDK motherboard. (Version 9)

Pin 16 connects to Pin 9 of J6G1 the RF Module.

3 J2A1 Video and Audio Port

1 Red Gnd 2 Green Ground 3 Red (Cr in HDTV mode) 4 Green (Y in HDTV mode) 5 Composite Gnd 6 Blue Ground 7 Composite (Sync in RGB mode) 8 Blue (Cb in HDTV mode) 9 H-sync Gnd 10 V-sync Gnd 11 H-sync (VGA Mode) 12 V-sync (VGA Mode) 13 Audio-R Gnd 14 Audio-L Gnd 15 Audio-R 16 Audio-L 17 Switching voltage (for SCART pin-8) 18 CBL-ID1 19 Blanking Signal (for SCART pin-16) 20 CBL-ID1.1 21 Unknown 22 CBL-ID2 23 Unknown 24 CBL-ID2.1 25 Optical - Audio (SPDIF) 26 CBL-ID3 27 Optical - Gnd (SPDIF) 28 CBL-ID3.1 29 Optical - +5V 30 See J2B1 or J8C1 Setting Cable ID: ID1-1.1 = VGA mode enabled ID2-2.1 and ID3-3.1 = RGB (SCART) mode enabled ID3-3.1 = HDTV (Y/Cb/Cr) mode enabled ID2-2.1 = Composite (TV) mode enabled Manufacturer: Unknown Product: Unkown

Note: Source: www..org (corrected Pin#s and added pin 30)

4 J3A1 Fan Connector

1 GND Blue 2 V+ Brown 3 GND Black 4 V+ Red

Manufacturer: Foxconn Product:

Note: V+ Starts at +5.4 VDC and climbs to +11.8 VDC within 30 sec of power on.

5 J9A1 DC Power Port

1 GND 6 +12 VDC 2 GND 7 Power Enable 3 GND 8 +5 VDC (Standby) 4 +12 VDC 9 Shield (GND) 5 +12 VDC 10 Shield (GND) Note: Pin 7 Turns Pins 4, 5, 6 on when it is tied to ground.

Power Supply is difficult to open up. I would not recommend it. 1) Remove rubber feet (they are glued in place). This will probably destroy them. 2) Dig out all the glue, including the glue in the head of the philips screws. 3) Remove the 4 screws. 4) Remove bottom cover. 5) Remove the two philips screws. One on each side of the heat sink. 6) Gently wiggle circuit board out of the top cover. The DC supply side should lift up first. Heat sink grease is preventing the easy removal of the circuit board. Continue to wiggle the circuit board until the grease bond is broken.

6 J9A2 XDK DC Power

1 +5 VDC (Standby) 2 GND

Manufacturer: Unknown Part #: Unknown

Note: This connector is used to supply power to the extra circuitry used in the XDK (motherboard version 009). The circuitry is located in the "Sidecar" that attaches to the hard drive side of the xbox 360.

7 J2B1 XDK Debug Header

Power ON Power Off Data Present 1 RX - U2C1 pin 15D1 +3.3 VDC 0 No 2 TX- U2C1 pin 14D1 +3.3 VDC 0 No 3 NC 0 0 No 4 Connects to U2C1 pin 16B +3.3 VDC +3.3 VDC No 5 Eject2 +3 VDC 0 No 6 Connects to U2C1 pin 16C 0 0 No 7 +3.3 VDC (Standby) +3.3 VDC +3.3 VDC No 8 +3.3 VDC +3.3 VDC 0 No 9 SDA +3.3 VDC +3.3 VDC Yes 10 SCL +3.3 VDC +3.3 VDC Yes 11 See Schematics +3.3 VDC +3.3 VDC No 12 GND 0 0 No 13 +5 VDC (Standby) +3.3 VDC +5 VDC No

Note: 1) Speculation: Document posted on xboxhacker.net and free60.org suggests that these pins are UART operating at 115000 bps. 2) Quick pulse Ejects, otherwise 360 immediately shuts down.

8 J1C1 DVD SATA Connector

1 GND 2 A+ 3 A- 4 GND 5 B- 6 B+ 7 GND

Manufacturer: Tyco Part #: Unkown

Note: Standard SATA interface. Each DVD drive has a unique ID key. (source: www.xboxhacker.net)

9 J5C1 ANA Header

Power ON Power Off Data Present 1 Connects to Pin 71 of U4B1 +1.8 VDC +1.8 VDC No 2 Connects to Pin 70 of U4B1 +1.8 VDC +1.8 VDC No 3 Connects to Pin 69 of U4B1 0 0 No 4 Unknown 0 0 No 5 Connects to Pin 72 of U4B1 0 0 No 6 GND 0 0 No

10 J5C2 GPU SPI EEPROM Header

Power ON Power OFF Data Present 1 SCK 0 0 high on startup 2 SO 0 0 3 SI 0 0 4 /WP +1.8 VDC +1.8 VDC 5 /CS +1.8 VDC +1.8 VDC brief activity at startup 6 GND 0 0 Note:

11 J8C1 CPU JTAG Header

Power ON Power OFF Data Present 1 0 0 No 2 +1.1 VDC 0 No 3 +1.8 VDC +1.8 VDC 0 No 4 +1.8 VDC 0 No 5 GND 0 0 No 6 +1.8 VDC 0 No 7 +1.8 VDC 0 No 8 +1.8 VDC 0 No 9 +3.3 VDC +3.3 VDC No 10 +1.8 VDC 0 No Note: Images indicate this port was used during hardware development. Pin 9 was not used in HDK image. The pin header is also present on the XDK version 9 motherboard. Speculation: GPULDBG, Inputs - TDI, TMS, TCK, Output -TDO, and RESET

12 J1D1 DVD Power Connector

1 NC 7 GND 2 NC 8 +5 VDC 3 Open/Close 9 GND 4 Tray Status 10 +12 VDC 5 GND 11 GND 6 +3.3 VDC 12 +12 VDC

Manufacturer: Part #:

Notes: Open/Close: momentary tied to gnd to open/close drive door. Tray Status: +3.3 VDC tray is open. 0 v tray is closed. Source: www.xboxhacker.net

13 J1D2 XDK Debug Header #2

Power ON Power OFF Data Present 1 Connects to U2C1 pin 5Y 0 0 No 2 Connects to U2C1 pin 5AA +3.3 VDC +3.3 VDC No 3 Connects to U2C1 pin 3U 0 0 No 4 Connects to U2C1 pin 5AB +3.3 VDC +3.3 VDC No 5 +5 VDC (Standby) +5 VDC +5 VDC No 6 GND 0 0 No 7 GND 0 0 No 8 Unknown 0 0 No 9 Unknown 0 0 No

Note: This port is used in the XDK version 9 motherboard. The connector is routed into the XDK "Sidecar" expansion module.

14 J2D1 Southbridge Header

Power ON Power OFF Data Present

1 Connects to U2C1 pin 21V +1.8 VDC 0 No

2 Connects to U2C1 pin 22W +1.8 VDC 0 No

3 Connects to U2C1 pin 22V 0 0 No

4 Connects to U2C1 pin 21W 0 0 No

5 Connects to U2C1 pin 20W 0 0 No

6 GND 0 0 No

15 J2D2 GPU Header

Power ON Power OFF Data Present 1 Connects to U4D1 pin 12E +1.9 VDC 0 No 2 Connects to U4D1 pin 12F +1.9 VDC 0 No 3 Connects to U4D1 pin 12D 0 0 No 4 Connects to U4D1 pin 11G 0 0 No

5 Connects to U4D1 pin 13E 0 0 No 6 GND 0 0 No 7 See Note +1.9 VDC 0 No

8 Connects to U4D1 pin 13G 0 0 No Note: There are images of a XDK motherboard (version 9) on the Internet that shows a green wire connecting Pin 5 to the Southbridge(21J). Pin 7 - still working on it.

16 J1E1 Hard Drive SATA Connector

1 GND 8 GND 2 A+ 9 GND 3 A- 10 GND 4 GND 11 +5 VDC 5 B- 12 +5 VDC 6 B+ 13 +5 VDC 7 GND 14 +5 VDC (standby)

Manufacturer: Unknown-Made in China Part #: XB00351-002

17 J1F1 Southbridge LED Header

Power ON Power OFF Data Present

1 +5 VDC +5 VDC 0 No

2 GND 0 0 No

3 Connects to U2C1 pin 20D +3.3 VDC 0 No

4 Connects to U2C1 pin 21D 0 0 No OFF- 1.25 hz 5 Connects to U2C1 pin 22D +3.3 CLK +3.3 CLK ON - Activity 6 Connects to U2C1 pin 21C 0 0 No

Note: Some images of the pre version 9 360 motherboard show LEDs connected to this Port.

18 J7F1 CPU SPI EEPROM Header

1 SCK 4 /WP

2 SO 5 /CS

3 SI 6 GND

Note:

Header and eeprom is present on 360's XDK (Version 9)

Eeprom is missing on some Version 11 motherboards.

Connects to the SPI serial eeprom (AT25020) then it probably connects to the Misc I/O bus on the CPU.

19 J3G1 Front Memory Card A & B Connector

A B

6 GND 1 GND

7 +3.3 VDC 2 +3.3 VDC

8 USB Data - 3 USB Data -

9 USB Data + 4 USB Data +

10 GND 5 GND

Note: USB is 3.3 VDC, Same as RF Module.

20 J6G1 RF Module Connector

1 +3.3 VDC 5 See Note

2 USB Data - 6 Serial Data

3 USB Data + 7 Serial CLK

4 GND 8 GND

9 See Note

Note: USB is 3.3 VDC, same as memory card port Pin 5 Power ON/OFF (momentary tied to gnd to power ON/OFF) Pin 5 goes to southbridge 21E Pin 9 goes to Pin 16 of J1A1 (extra pin on the back USB port) but is not connected to anything on the RF Module.

21 J7G1 Aux Power Header

1 GND 2 +12 VDC1 3 GND

Note: 1) This port is not active. A resistor or jumper needs to be added to the bottom side of the motherboard were R7V7 should be.

Header missing on 360 XDK motherboard Version 9.

Header missing on 360 Retail motherboard Version 11.

22 J7G2 VID Port

1 VCC 8 VID1

2 VID4 9 PWM1

3 FBRTN 10 VID0

4 VID3 11 PWM2

5 PWRGD 12 VID5

6 VID2 13 PWM3 7 EN 14 GND

Note: Pure Speculation

The Voltage Identification (VID) port was present on early version(s) of the 360 motherboard. (pre Version 9)

I have speculated what the connections were. To learn more download the datasheet for the ADP3188. (Analog Devices)

23 J9G1 Front Dual USB Port

Bottom Port Top Port 1 +5 VDC 5 +5 VDC 2 USB Data - 6 USB Data - 3 USB Data + 7 USB Data + 4 GND 8 GND

24 Appendix

Document Version

Version 1.0 Dec 15, 2005 Just Pinouts

Version 1.1 Dec 30, 2005 Added Photos & Diagrams

Version 1.2 Jan 6, 2006 Changed Format

Version 1.3 Feb 2, 2006 Added Schematics Private Release

Version 1.4 Feb 15, 2006 Corrected Schematics Added Appendix Added Block Diagram Current Document

25 Unique Per Console Numbers

L = Production line in the factory NNNNNN = Xbox in the week Y = Year (last digit) WW = week of the year * FF = Factory # (05 & 06 are China, 05 appears to supply Europe and 06 supplies North America) MM = Month X = unknown at this time " " = Actual Text

* Factory 05 is a week ahead of factory 06 for the 2005 year. This means any 360 made during the last week of December 2005 should have a WW=53 in the serial #.

Serial Number = LNNNNNNYWWFF (Source: www.xbox-.org)

Product ID = XXXXXXXXLNNNNNNYWWFF

Motherboard = XXXXXXXXXXXXYWWX

Console ID = XXXXXXXXXXXX

Wired MAC = Unique 12 digit (hex, meaning each digit has the possibility of being a value of 0-F)

RF Module = XXXXXXXXXXXYWW

DVD Serial # (Hitachi-LG) = YMM"HG"XXXXXX

DVD Serial # (Toshiba- Samsung) = X"RCY"XXXXXX

26 Retail Motherboard Differences

Motherboard Version 011 CPU SPI eeprom: Present or Absent CPU: Engraved "Canada" or "Taiwan" Tilt Switch: Surface Mount or Thru Hole Mount Bios Label: Present or Absent 10/100 base-TX Ethernet Transceiver: "Big" or "Small" Header Holes: Filled in with solder, partially filled or not filled.

27 Bios/Kernel Versions and Updates

Displayed in the dashboard. D: = Dashboard K: = Kernel BK: = (Backup Kernel, Bios Kernel, Base Kernel, etc) - Not sure

2.0.0198.0 First image of a XDK Launcher Screen. Show version in the right hand corner. I'm guessing it's an Alpha. (Source Image: I forget)

2.0.1232.0 Alpha 2 Image of a XDK Launcher Screen. Alpha 2 is displayed beside version #. (Source Image: I forget)

2.0.1839.2 XeDK release Dashboard. (smartxx images)

2.0.1888.0 Sept-Oct Production Line for Retail Release

2.0.2241.0 Late Oct-Early Nov Production Line, Nov 22 available over xbox live. * Unknown

2.0.2255.0 Jan 30 production line, Jan 30 available over xbox live * Improved logic around deciding if saved games should be deleted and offer the option to only delete the profile and to leave all save data. * Users reporting blank Friends List on the Xbox 360 dash after muting a friend while playing a game in Backwards Compatibility mode. * Improved synching of games played to Web and in console. * Network settings: keyboard does now allow entry of - (dash) character in the keyboard. * Improvements to the Xbox Guide. * Increased accuracy of "last time played." * Network configuration improvements for Xbox Live members in the Netherlands. * More detailed messaging for unreadable disk or region errors. * Blocked the Kiosk Disc from being recognized when inserted into the DVD tray. (Source: I forget, so let me know so I can provide proper credit)

28 System Requirements

Absolute Minimum

Motherboard, Power Supply (12 volt 16amp, 5 volt 1amp), Video Cable, and a momentary pushbutton switch (for power on/off).

I have tested this with dashboard 1888 and 2241. A dashboard update could change this.

Absolute Minimum to play games or DVDs

As above, but subtract the push button and add the DVD player and a wired controller.

Absolute Minimum to play just DVDs

As above, but the remote can be used instead of the wire controller.

Remember that this could change with a dashboard update.

29 Retail

Note: Flash Bios Version 2.0.1888.0

30 XeDK

Note: Appears to be a final version of the XeDK. Flash Bios Version 2.0.1839.2 Also known as XDK. Used in conjunction with the SDK (Software Development Kit). Most likely, the XeDK is also connected to a network with various PCs running SDK.

Source: www.smartxx.com

31 HDK

Note:

No DVD connected. Source: www.xavbox.com

32 Memory Map

Not in this Public Release

33 CPU Pinout

Not in this Public Release

34 GPU Pinout

Not in this Public Release

35 Southbridge Pinout

Not in this Public Release

36 Left Blank

37