MODERN SHIPLAP INSTALLATION INSTRUCTIONS PLAN CUT FASTEN LAYOUT PRIOR USING STANDARD USE SUPPLIED STARBORN PRO PLUG®️ TO INSTALLATION SCREWS, OR EXTERIOR #6 OR #8 SCREWS

DO NOT DO NOT DO NOT DO NOT STORE COVER DRAG INSTALL WHERE TEMPERATURES WITH COULD SCRATCH IMPROPERLY COLORED MAY EXCEED 1200 DARK MATERIAL MATERIAL BOARDS PREPARATION FASTENING SCARF Apply NuCedar products over a properly installed weather ■■ A scarf joint is best for joints, or you can JOINT resistant barrier (ex. House Wrap) and ensure all wall openings and Z-Flash with color matched coil stock penetrations are properly flashed in accordance with local building ■■ All required fasteners are included with CUT 450 codes and window/door manufacturer’s flashing recommendations. your order The NuCedar cladding system is not a water-tight barrier. It is ■■ Regardless of board length, make sure to use designed to reduce the amount of water that reaches the underlying an extra screw in the center as shown below JOIN WITH FASTENERS weather resistant barrier. All forms of NuCedar Vertical Siding AND ADHESIVE must be installed over a continuous, flat surface capable of 2" supporting the use of screws that will restrict temperature related expansion and contraction of the siding (Ex. OSB or ). NuCedar Vertical Siding cannot be installed over open or furring strips. Along the 16" VERTICAL INSTALLATION length: Fasteners no farther FASTENER apart than PLACEMENT 16” 16" 2"

2"

16" HOUSE WRAP 16" Use additional fasteners INSTALL SIDING in center as OVER SOLID shown SHEATHING SUCH 16" HORIZONTAL INSTALLATION AS PLYWOOD OR OSB FASTENER PLACEMENT 2" 16"

16" HOUSE WRAP Exactly 2” 2" 16" from the end of the board 2" 4” WIDE 6” WIDE 8” WIDE 10” WIDE

NORTHEAST REGION: SOUTHEAST REGION: PHONE: (800)526-4708 PHONE: (800)296-0288

WWW.GARDENSTATELUMBER.COM MODERN SHIPLAP INSTALLATION INSTRUCTIONS CORNER INSTALLATION OPTIONS

HORIZONTAL APPLICATION VERTICAL APPLICATION J Corner: Siding slides under corner Keep 1/16” gap between No gap needed for corner and siding vertical application 1/16" J CORNER

OR

STANDARD Standard Corner: Siding butts to edges CORNER Keep 1/16” gap between No gap needed for corner and siding vertical application 1/16"

Mitered Corner: Stacked Corner: Cut at 45 degrees Overlap corner of wall Screws exactly 2” from by 5/8”, butt in piece the end of the board from adjoining wall

2” 2” MITERED STACKED CORNER 2” 2” CORNER

Use Fill & Flex, Fast Cure, or consult a Representative for other options

TOUCH-UP AND RE-PAINTING CARE AND MAINTENANCE ALL TOUCH UP MUCH BE SHAKEN VIGOROUSLY TO ENSURE COLOR NuCedar products can be safely cleaned using a mixture of water and MATCHES. Apply touch-up paint on all cuts, planed edges and small mild detergent or a mild household cleaner. Remove mold/mildew damaged areas. NuCedar can be touched up with a high-grade exterior using a mild commercial mold/mildew remover. NuCedar can be lightly latex paint. NuCedar recommends PPG MANOR HALL® Exterior 100% sprayed or cleaned with a house brush (high pressure power-washers Acrylic Latex Paint. In the future, if you would like to repaint the product, it could destroy the Rough Sawn texture) to remove dust and debris. is possible to do; however, you will void your warranty going forward. For Refer to manufacturer’s instructions. re-painting, use a high-grade exterior latex paint, such as PPG Manor Hall (Exterior, Satin Finish). Make sure that your paint color has a Light Reflective INSTALLATION MUST FOLLOW THE INSTRUCTIONS IN Value (LRV) of 55 units or greater. Prior to touching up or repainting, make THIS MANUAL TO MAINTAIN PRODUCT WARRANTY sure that the surface area is properly cleaned and prepared according to In order to secure your warranty, please visit our website to register your product: gardenstatelumber.com/NuCedar/technical/warranty/ For additional copies and manufacturer’s specifications. revisions, go to gardenstatelumber.com/NuCedar.

NORTHEAST REGION: SOUTHEAST REGION: PHONE: (800)526-4708 PHONE: (800)296-0288

WWW.GARDENSTATELUMBER.COM