Technic Electrolytic Precious Metals

Total Page：16

File Type：pdf, Size：1020Kb

Technic Electrolytic Precious Metals About Technic Technic is a world leader in precious metal plating. With over 50 years of experience in electronics, connector and decorative plating, Technic has develop specialty products for printed circuit board applications. While exceeding deposit requirements, the Technic Precious Metal products for PCB are specifically designed for compatibility with aqueous dry film, high throw, high speed as well as cost savings through better distribution and lower gold usage. Technic provides a full range of electrolytic nickel, soft and hard gold as well as palladium, rhodium, platinum, and silver. Electrolytic Nickel Techni Nickel S: Conventional sulfamate nickel. Good for military applications and for aspect ratios below 10:1. Nickel S will reduce slivering in full panel Nickel Gold product compared to a standard bright Nickel sulfate deposit. Techni Nickel HT-2: Sulfate Nickel for high aspect ratio applications over 10:1 aspect ratio and holes sizes below 18 mils. Techni Nickel HT-2 will dramatically improve throwing power compared to sulfate or sulfamate chemistries. Technic Test Vehicle: Cross-section Data Technic HT-2 Nickel • DC Plate, Standard Production plating Cell • 15ASF (1.5 ASD)18 Minutes • 100 Thousands (2.5mm)Thick PCB • 10 Mil (0.25mm)Hole • 0.100 Mil(2.5 microns) Min Ni in Center of the Hole • 50% Average Throwing Power High Speed Nickel Sulfate FFP: High speed process for plating sulfate nickel in an automatic tab plater. The deposit is low stress www.technic.com semi bright and ductile. This process can be used with soluble or [email protected] insoluble anodes (401) 781-6100 © Technic Inc. Electrolytic Gold Oroscene 80RC: Hard gold process that can be used in high speed tab platers or in deep tank operations. The process has a high tolerance for contamination and provides excellent distribution. The deposit purity and low contact resis- tance makes it a perfect choice for touch contacts, slide contacts, as well as soldered connections. • Deposit purity : >99.7% • Hardness : 140 - 170 Knoop (25 gm load) • Resistivity : <0.3 mOhm/cm • Density : 17.5 - 18.5 gm/cm3 Oroscene Solder Joint Strength vs Ni Concentration 15 0 PPM 500PPM 10 1000PPM 5 1500PPM Strength(Kg) 2000PPM 0 2500PPM 1 3 5 7 9 11 13 15 17 19 Point Technic 434 HS Designed to produce a Gold electrodeposit of 99.9+% purity for devices where high purity Gold deposits are required to meet wire bonding requirements. Deposits obtained from this system meet the requirements of Mil-G-45204C, Type III, Grade A. • Deposit purity : >99.9% • Hardness : 80 – 90 Knoop (25 gm load) as plated • Resistivity : <0.3 mOhm/cm Technic 434 HS 1 Mil Gold Wire Bond Pull Strength 25.00 20.00 15.00 STD 10.00 Div Grams AVE 5.00 www.technic.com 0.00 [email protected] set 1A Plasma set2A plasma set 1B Plasma set 2B plasma (401) 781-6100 Board 1 Board 2 © Technic Inc. Cranston, RI • Anaheim, CA • San Jose, CA • Illinois • Texas • Canada • Europe • Hong Kong • Japan • Korea • Singapore • Taiwan.

Copy Link

Recommended publications

Metals and Metal Products Tariff Schedules of the United States
251 SCHEDULE 6. - METALS AND METAL PRODUCTS TARIFF SCHEDULES OF THE UNITED STATES SCHEDULE 6. - METALS AND METAL PRODUCTS 252 Part 1 - Metal-Bearing Ores and Other Metal-Bearing Schedule 6 headnotes: Materials 1, This schedule does not cover — Part 2 Metals, Their Alloys, and Their Basic Shapes and Forms (II chemical elements (except thorium and uranium) and isotopes which are usefully radioactive (see A. Precious Metals part I3B of schedule 4); B. Iron or Steel (II) the alkali metals. I.e., cesium, lithium, potas C. Copper sium, rubidium, and sodium (see part 2A of sched D. Aluminum ule 4); or E. Nickel (lii) certain articles and parts thereof, of metal, F. Tin provided for in schedule 7 and elsewhere. G. Lead 2. For the purposes of the tariff schedules, unless the H. Zinc context requires otherwise — J. Beryllium, Columbium, Germanium, Hafnium, (a) the term "precious metal" embraces gold, silver, Indium, Magnesium, Molybdenum, Rhenium, platinum and other metals of the platinum group (iridium, Tantalum, Titanium, Tungsten, Uranium, osmium, palladium, rhodium, and ruthenium), and precious- and Zirconium metaI a Iloys; K, Other Base Metals (b) the term "base metal" embraces aluminum, antimony, arsenic, barium, beryllium, bismuth, boron, cadmium, calcium, chromium, cobalt, columbium, copper, gallium, germanium, Part 3 Metal Products hafnium, indium, iron, lead, magnesium, manganese, mercury, A. Metallic Containers molybdenum, nickel, rhenium, the rare-earth metals (Including B. Wire Cordage; Wire Screen, Netting and scandium and yttrium), selenium, silicon, strontium, tantalum, Fencing; Bale Ties tellurium, thallium, thorium, tin, titanium, tungsten, urani C. Metal Leaf and FoU; Metallics um, vanadium, zinc, and zirconium, and base-metal alloys; D, Nails, Screws, Bolts, and Other Fasteners; (c) the term "meta I" embraces precious metals, base Locks, Builders' Hardware; Furniture, metals, and their alloys; and Luggage, and Saddlery Hardware (d) in determining which of two or more equally specific provisions for articles "of iron or steel", "of copper", E.
[Show full text]
PARASITES PREDATORS and SYMBIONTS a Thesis Submitted To
PARASITES PREDATORS AND SYMBIONTS A thesis submitted to the College of the Arts of Kent State University in partial fulfillment of the requirements for the degree of Master of Fine Arts By Jody L. Vankeuren May 2021 Thesis written by Jody L. Vankeuren B.F.A., Edinboro University of Pennsylvania, 2018 M.F.A., Kent State University, 2021 Approved by Andrew Kuebeck, M.F.A., Advisor Marie Buukowski, M.F.A., Director, School of Art John R. Crawford- Spinelli, Ed.D., Dean, College of the Arts TABLE OF CONTENTS Page LIST OF FIGURES ......................................................................................................................................................... IV AKNOWLEDGEMENTS ............................................................................................................................................. V CHAPTER 1. INTRODUCTION .................................................................................................................................................. 1 2. RESEARCH ............................................................................................................................................................. 1 3. PARASITES PREDATORS AND SYMBIONTS- INDIVIDUAL WORKS ............................................. 4 4. INSTALATION ...................................................................................................................................................... 8 5. CONCLUSION .......................................................................................................................................................
[Show full text]
Rhodium Roles Lars Öhrström Relates the Various Roles Played by Rhodium in Our Daily Lives, Ranging from Car Components to Drugs
in your element Rhodium roles Lars Öhrström relates the various roles played by rhodium in our daily lives, ranging from car components to drugs. nce the thin electroplated rhodium information to be extracted by 2D NMR coating that makes new pieces spectroscopy techniques. Oof jewellery extra bright and Several artificial radioactive isotopes are shiny wears off, most of us are likely to also known, including meta-stable nuclear come across rhodium mainly as a crucial isomers. One of those, 103mRh — produced component in catalytic converters for by decay from 103Ru — has been investigated cars. In these devices, metallic particles of as a cancer therapy agent2. In light of its element 45 are embedded in the porous short half-life (59 min) and the slow ligand ceramic structure of the catalyst, and its exchange rates for Rh(iii) complexes, specific role is to help break down nitrogen however, the synthesis and use of 103mRh oxides to innocuous O2 and N2. compounds require careful planning. 4+ In 1988, a year before catalytic converters A variety of complexes based on the Rh2 became compulsory for new cars in Sweden, core have also shown promise as anticancer I encountered this otherwise silver-white compounds. Recently, in an exciting noble metal in a very different form: development, a dirhodium(ii) compound 50 grams of a purple powder, worth half a featuring a ligand endowed with an organic year’s pay for a graduate student. This price 3, ACS REF. FROM REPRODUCED fluorophore has been shown to be taken up reflected both the fact that element 45 is for applications, and the reason behind by cancer cells in a different manner than the typically the most expensive of the platinum William S.
[Show full text]
Advertising Platinum Jewelry
FTC FACTS for Business Advertising Platinum Jewelry ftc.gov The Federal Trade Commission’s (FTC’s) Jewelry Guides describe how to accurately mark and advertise the platinum content of the jewelry you market or sell. Platinum jewelry can be alloyed with other metals: either precious platinum group metals (PGMs) — iridium, palladium, ruthenium, rhodium, and osmium — or non-precious base metals like copper and cobalt. In recent years, manufacturers have alloyed some platinum jewelry with a larger percentage of base metals. Recent revisions to the FTC’s Jewelry Guides address the marking of jewelry made of platinum and non-precious metal alloys and when disclosures are appropriate. When Disclosures Should Be Made Product descriptions should not be misleading, and they should disclose material information to jewelry buyers. If the platinum/base metal-alloyed item you are selling does not have the properties of products that are almost pure platinum or have a very high percentage of platinum, you should disclose that to prospective buyers. They may want to know about the value of the product as well as its durability, luster, density, scratch resistance, tarnish resistance, its ability to be resized or repaired, how well it retains precious metal over time, and whether it’s hypoallergenic. You may claim your product has these properties only if you have competent and reliable scientific evidence that your product — that has been alloyed with 15 to 50 percent non-precious or base metals — doesn’t differ in a material way from a product that is 85 percent or more pure platinum. Facts for Business Terms Used in Advertising • Jewelry that has 850 parts per thousand pure platinum — meaning that it is 85 percent pure • Any item that is less than 500 parts per platinum and 15 percent other metals — may be thousand pure platinum should not be marked referred to as “traditional platinum.” The other or described as platinum even if you modify the metals can include either PGMs or non-precious term by adding the piece’s platinum content in base metals.
[Show full text]
Electroplating Guide & Catalogue
ELECTROPLATING GUIDE & CATALOGUE 2 ABOUT WIELAND Palloys is committed to innovation, quality, reliability and continued support of the jewellery industry - so our customers’ success becomes our success. That’s why we are so proud to be Australia’s exclusive distributor of Wieland Plating products. Wieland is acknowledged as the leading brand of plating products in the precious metals industry. The portfolio comprises of a wide range of electrolytes used in both functional and decorative electroplating. HOW TO ORDER? Simply call, email, fax or log online to place an order. ONLINE EMAIL PHONE FAX palloys.com.au [email protected] 1300 886 108 +61 2 8571 9222 3 Wieland and Palloys are part of Pallion. Pallion is Australasia’s premier precious metals service group. We employ Australia’s most experienced team of metallurgists, chemists, designers and fabricators to ensure that all Pallion products are of the finest quality. Our scale means that we are able to deliver superior value. With distribution offices in Sydney, Melbourne, Brisbane and Perth, coupled with volume manufacturing capability in Hong Kong and mainland China through our subsidiary Goldenage International. Pallion offers its clients unmatched geographical reach and customer service. Pallion offers a full service solution for precious metals including: • Bullion - Pallion is the exclusive distributor of one of the cornerstones of the Australian gold trading system - ABC Bullion, the Australian Bullion Company. • Refining & Minting -Pallion operates Australasia’s largest and most technologically advanced independent precious metal refining and minting facility – ABC Refinery. • Casting & Custom Jewellery - Pallion operates Australia’s premier jewellery casting and custom jewellery production service at Palloys and Goldenage International.
[Show full text]
Less Costly Palladium a Bigger Role in the Treatment of Nox, Diesel And
less costly palladium a bigger role in the treatment of The story gets better, if a little less certain, at this NOx, diesel and even gasoline engine emissions. point, as much of the underlying data is still proprietary. In the past PGM substitution usually required using Treatment of NOx emissions to date has been the near exclusive domain of rhodium, but new research larger amounts of palladium to replace a given amount has highlighted the potential to substitute palladium of platinum or rhodium. Switching to palladium from platinum, for example, has generally been thought in some NOx applications. Similarly, diesel emissions treatment, initially almost the exclusive domain of to require about 1 ½ times as much palladium in platinum, is now shifting toward increasing proportions conventional applications. Recent breakthroughs suggest of palladium in well established applications, with the ratio is now closer to a 1-to-1 replacement ratio of such use being rapidly expanded – especially as auto palladium for platinum in many applications. Switching from rhodium to palladium for NO reduction has been manufacturers struggle to reduce costs. Japanese auto x manufacturers, which until now have been reluctant to discussed in terms of needing 4 to 8 times as much switch from platinum to palladium for treating gasoline palladium to get the same catalytic result. But that, too, engine emissions, in the face of high platinum prices now may be getting closer to a 1-for-1 replacement ratio. and financial challenges generally, are now switching And while a substitution ratio at 1-to-1 will require fewer toward palladium, as well.
[Show full text]
Rhodium Plating
Rhodium Plating Dr. Ronald J. Morrissey Applications that deposits from the phosphate system are somewhat whiter, Rhodium is one of the whitest of metals, and this, together and mixed phosphate-sulfate systems are sometimes used. with its hardness and resistance to wear and tarnishing, have Insoluble hydrous oxides of rhodium can form at quite low established it as a premier finish for jewelry and decorative pH values. In order to avoid this, it is important to maintain work of all types. Its stable contact resistance and high the acidity of rhodium plating solution. All other things being melting point have also made it useful in electrical and equal, this is more easily accomplished in the sulfate than in electronic applications, notably in reed blades, in which its the phosphate system. resistance to arcing is particularly advantageous. Rhodium For decorative applications, rhodium plating solutions is, however, also the most expensive of the precious metals. rarely contain more than about 2 g/L rhodium, together with In recent years, its use has, with few exceptions, been about 20 mL/L of concentrated sulfuric acid. For heavier restricted to very thin deposits, usually over other white deposits, the rhodium content is increased to about 4-10 g/L, metals such as nickel, silver or, in the case of reed blades, together with about 20-50 mL/L sulfuric acid. In either case, ruthenium. plating is carried out at about 1-5 A/dm2 at 40-45 °C. Proprietary stress-relieving agents are available, but in any Processes event, it is difficult to plate rhodium in a crack-free condition Although rhodium can be evaporated under vacuum, in from aqueous solution at thicknesses much above 2 to 2.5 practice it is almost always electrodeposited.
[Show full text]
Heraeus Precious Forecast Update September 2020
HERAEUS PRECIOUS FORECAST – UPDATE 1st September 2020 PRECIOUS METALS FORECAST – UPDATE 79 Au Gold YTD change: +28.8% Forecast update High: $2,200/oz Low: $1,850/oz Safe haven demand can keep gold at record levels A combination of low-to-negative government bond yields Despite weak consumer demand, strong investor demand is likely and unprecedented fiscal and monetary stimulus has driven to continue to provide support for gold. A great deal of political safe-haven gold demand in the year to date. Indeed, the and economic uncertainty is already priced in. However, the macroeconomic and geopolitical landscape is expected to remain pandemic is far from over and if the economic outlook worsens, supportive of gold for the rest of the year. The economic outlook central banks could increase their monetary interventions yet remains uncertain amidst the ongoing coronavirus pandemic and again. Investors will continue to see gold as a safe haven, pushing the continuing tensions between China and the US. Additionally, prices higher. In the near term, gold could move sideways as a divisive US presidential election is in prospect. it consolidates following its rapid rally to record highs in early August. The price is estimated to trade within a range of $1,850/ Record gold prices and economic disruption have weighed oz and $2,200/oz over the last few months of the year. heavily on consumer demand. Gold prices have hit record highs in most currencies this year. Jewellery purchases in the first half of the year slumped 46% year-on-year as major markets were Gold price in lockdown and disposable income was slashed.
[Show full text]
The Platinum Group Metals As Coating Materials
Issue No. 38 – February 2012 Updated from Original August 2002 Publication The Platinum Group Metals as Coating Materials How precious is your metal - An overview on The platinum group metals consist of platinum and palladium, as well as rhodium, iridium, the use of the platinum osmium, and ruthenium. They can be found in the transition metals on the periodic table of the elements. A close-up of this part of the table is shown in Figure 1. Palladium is currently the group metals as contact surfaces for electronic only metal of the group in widespread use in electrical contacts, although platinum was widely connectors. used in the past. Rhodium is only used in electrical contact applications requiring very high hardness and wear resistance. The other three metals in the group are used mainly in other industrial applications. Pure, electroplated platinum and palladium have a hardness of around 200 to 400 HV, although . Platinum they may also be applied by cladding. Both have a conductivity of around 16% IACS. Thus they are harder than gold, but slightly less conductive. At one time, their prices were . Palladium competitive with gold, and gold-flashed palladium coatings were even used as less expensive alternatives to gold coatings. However, both of these metals are much more expensive than gold . Rhodium (at least at the time of this writing). Due to its cost, gold-flashed palladium is now used mainly in applications which require greater hardness and wear resistance than hard gold alone. Ruthenium Rhodium is much harder than platinum and palladium, typically 800-1000 HV, with an .
[Show full text]
Rhodium Plated Over Sterling Silver
Rhodium Plated over Sterling Silver Some of my items are bought from various places around the world and are rhodium plated. Although rhodium plating is commonly used in jewellery, not many people know what it is. Rhodium plating is used to enhance the lustre and durability of metals such as silver and white gold and gives a smooth, shiny finish to the jewellery. It is especially attractive when used for diamond rings, as it can really enhance the brilliance of the diamond. However, there are some downsides to choosing rhodium plating, such as the time and money involved in ongoing re-plating over the years. Not sure if rhodium plating is something you want to deal with? Here we outline the 10 things you need to know about rhodium plating before you buy. Rhodium plating, also known as rhodium dip or rhodium flashing, is used to increase the durability, lustre and light reflection of a piece of jewellery. Because it is a hard metal, a rhodium plated piece of jewellery will be more scratch resistant. Rhodium plating is mainly used on silver-hued metals, such as white gold, palladium or silver. Most rhodium plating has a thickness of .75 to 1.0 microns. Rhodium plated jewellery like this ring show a highly polished finish. Sterling silver is a white metal and does not necessarily need rhodium plating to acquire its colour. However, it tends to tarnish over time. To prevent this, rhodium plating silver jewellery will ensure that the piece is highly lustrous and remains tarnish-free for a long time.
[Show full text]
The SPARTINA MERMAID
JEWELRY SPRING/SUMMER 2017 The SPARTINA MERMAID Captivating colors, irresistible style—it was only natural that a mermaid became our insignia! The Spartina 449 mermaid is inspired by tales of sailors who, after nights of indulging in island spirits, gazed into the moonlit ocean and were convinced they saw mermaids swimming nearby. More than likely, they were actually swooning over local dolphins! For us, however, the legend is real. We incorporate an authentic Spartina mermaid into every product we design. THIS PAGE (left to right) Bellflower Layered Necklace 18" 519618 / Luxe Bead Feather Necklace 34” 519588 / Beaded Collar Necklace 16” Cream 519502 / Beaded Horseshoe Necklace 26” Cream 519496 / Bellflower Cuff 519984 II A TIME & PLACE On Edge Earrings 520218 / Bellflower Tassel Necklace 27" 519625 / Retreat Eastern Vines Scarf 945474 / Boho Chic Toggle Bracelet Sea Foam 519915 / Stretch Bracelet Assortment / Bamboo Chic Tilly Tote Sea Salt 943937 The Spirit of Island Living Inspired by one of the few remaining unspoiled treasures, Daufuskie Island, South Carolina, Spartina 449 handbags, accessories and jewelry embody the true beauty and spirit of island living. Like our signature linen and leather accessories, Spartina jewelry is crafted beautifully and meticulously. Our signature pieces blend high-quality 14- and 18- karat gold-plating, brilliant rhodium plating, colorful enamels, as well as selectively sourced crystal and resin gems and beads, including semi-precious stones and Swarovski glass. Combined, these materials make our jewelry shine and sparkle, capturing the glint of the summer sun, but also the attention of women across the country. Top-tier editors, stylists and fashion bloggers have regularly featured Spartina jewelry in Oprah Magazine, Redbook, Woman's Day, Glamour, on the TODAY Show, Good Morning America and more.
[Show full text]
Heraeus Precious Appraisal I 1 Precious Metals Review
HERAEUS PRECIOUS Ed. 21 APPRAISAL st 21 June 2021 MARKET SPOTLIGHT Auto chip shortage: a respite for palladium and rhodium? A shortage of semiconductors is the greatest risk to automotive PGM demand this year. Automakers cut their semiconductor chip orders in Q3’20 in line with pandemic-weakened vehicle sales, meanwhile chip-makers focused production on the lucrative consumer electronics sector. When automotive orders rebounded stronger than expected in Q4’20, a global shortage of chips emerged. As a result, almost every automaker has been forced to idle production at some point this year. The automotive sector is the largest end-user for platinum, palladium and rhodium, accounting for 41%, 83% and 88%, respectively, of total demand for each metal. The full-year impact on global vehicle production is currently forecast to be around 2 million units, mainly weighted towards Europe and North America (source: LMC Automotive, May 2021 estimate). Vehicle losses to this extent could reduce PGM demand by more than 300 koz this year, with palladium and rhodium consumption predicted to be particularly hard hit owing to the dominance of gasoline light vehicles in the areas worst affected by production cuts. Estimated light vehicle production impact Auto chip shortage: impact PGM demand Units (000) % loss of total auto demand 2021 Automakers begin to 1,000 0.0% recoup lost production in H2’21 500 -0.5% -1.0% 0 -1.5% -500 Pan Europe North America -2.0% -1,000 South America China -2.5% -1,500 Asia-Paciﬁc (less China) -3.0% RoW -2,000 -3.5% Q1 2021 Q2 2021 Q3 2021 Q4 2021 Pt Pd Rh Source: LMC Automotive (publicly available data) Source: SFA (Oxford) However, the impact on PGM demand is being mitigated by automakers’ ‘adapt and overcome’ response.
[Show full text]