Installation Instructions INC. for Crown Moldings

Please read entire instruction before proceeding. Improper installation will void any applicable warranty.

Foam Foam Left Inside Pieces Pieces Corner

Left Outside Right Inside Corner Right Outside Bull Adapter Corner Corner

Step 1: If required by local codes, paper tape or fire tape the inside corner prior to installing the Step 2: On a wall section where two crown . Always wear safety glasses when using miter , staple guns, or spray pieces of crown molding need to be adhesive. If necessary, attach some to the miter so the part is supported as shown. joined, it is easier to cut the miters first Break your saw to the left for a right inside or left outside corner. Break your saw to the right for a and leave the straight as the left inside or right outside corner. For additional support, place the foam spacer pieces near the last cut. When using Crown Molding blade. Use a fine tooth cross cut blade. To ensure accuracy, make the miter cuts slowly. Typically with Bullnose, use Bull Adapters as a 90º inside or outside corner will require setting the to 45º. Most corners are rarely a shown above. true 90º so you may need to adjust the angle and make some practice cuts first.

VERY Adhesive Caulk Pressure along top edge along the front edge IMPORTANT Wipe excess caulk

847

Trim-Tex 700/710 Caulk or Step 4: Starting at any miter joints, A piece of masking tape will Big Stretch along the front edge carefully install the crown molding hold the corner as the taking care to keep the product caulk sets. Step 3: You must apply a 1/2" of high to minimize gaps at miter joints. Apply quality white paintable adhesive caulk, such pressure to the bead along the top as Trim-Tex 700/710 caulk or Big Stretch from edge to bond the crown molding to the Sashco, along the front edge of the top flange ceiling and then pressure along the of the Crown Molding. Apply 847 Spray mud flange. Staple the mud flange Adhesive to the mud leg. every 6-8" with 1/2" staples. Staple mud flange every 6" Step 5: Wipe excess caulk that squeezed out from the top flange. Then caulk along the top Caulk along top edge edge of the crown molding, the inside and outside corners, and any butt joints. Apply compound along the mud flanges. For the Caulk Butt Joints ultimate in compound performance, add Mud- Max Drywall Compound Additive to your mud. the crown molding with a high quality latex paint. See graphic to the right. In extreme settling or movement conditions, the caulk may crack along the edge of the Crown Caulk Mitered Corners Mud - Sand - Paint Molding. Re-caulk as needed. 3700 W. Pratt Ave. Lincolnwood, IL 60712-2508 (847) 679-3000 1-800 874-2333 Fax: (847) 679-3017 www.trim-tex.com en de Big calidad, pegamento 3er area moldura, reventarse e c r aditivo roca Aplique pintable en lapartesuperior 5to tendra la multiples Para externo como engrapadoras encintar 1er o Esquina Interna o s c n sierra t aerosol la r Stretch paso d a Paso u Paso T T T a argietada. e Espuma Pieza de soporte

Derecha c molduradecoritiva. soporte rim-T rim-T rim-T c la que t p para i u izquierdo. o electrica como material : : a parte a y r la

n Si Limpie a : use r ajustar finos. e 847 la a l marcha ex 700/710CaulkoBigStretch ex 700/710CaulkoBigStretch ex 700/710CaulkoBigStretch , esquina s lo Aplique alolargodelapartesuperior alolargodelapartesuperior alolargodelapartesuperior adicional,

en material

para siliconizado parte y requieren el perforada, u e silicon a e pegamento Para l n se x

silcon la la Mueva el la

t para la r s IMPORT extremidad encuentre sierra e exceso m 847 sashco superior . Despuesapliquesilicon i moldura. m l con un parte i una e c Esquina Externa utilize del despues a o 700/710 j el los corte la s o n electrica

cinta r Aplique agregue MUY MUY sierra

terminado terminado Izquierda en

codigos capa d pintable de a la p e F posterior r Mueva preciso en y aerosol. i la e

pieza n a silicon perforada. s a ANTE de t a 45º. a parte a de u de v y c

la las b de l e practicar pegamento de or deleerlasinstr t MUD-MAX papel. derecha l T la de n a e La corte limpiar rim-T t d

uniones. construccion Si sierra de de a superior de pintable 1/2" espuma mayoria o m p de es . u i tabla tabla

despacio. e e ex Siempre alta nesesario unos n E para hacia d de t el la Una instalacionincorrecta,anularacualquiergarantiaaplicable Espuma Pieza de e o n o . . .

cerca

de cortes un la grapas extremidad espacios presion extremidad cuidado 4to en las Aplique silicon pintableenlosangulos local, Aplique siliconpintableenlapartesuperior Esquina Externa Esquina Externa corte Usualmente izquierda use de instale esquinas Paso angulo, inicialmente. la antes interno Derecha Derecha lentes divergentes navaja. a y : INC. madera Comenzando para a en la de Instr raramente escuadra perforada izquierdo instale un perforada. par al parte instalar Use un las Esquina Interna Esquina Interna corte usar sobre corte ucciones antesdecomenzar una de Izquierda Izquierda uniones. del de la la o sierras son

a Moldur 1/2". navaja ucciones deInstalacion interno para parte posterior la externo 90º moldura, Adesivo enla con cada moldura techo sierra Engrape 90º requiere minimizar los de electricas, por derecho Aplique derecho. 6" electrica y cortes dientes debera lo a con con Aplique siliconpintableen lasuniones cual que la la o muestra use Molduras donde es y 2 el adesivosecure el adesivosecure la esquinaensulugarhastaque la esquinaensulugarhastaque Un trozodecintaadesivamantiene Un trozodecintaadesivamantiene Limpie elexeso Precione laparteposterior ndo por as decor preferible Aplique Material -LijarPintar el ultimo Paso adaptador Bull se en requiere Decorativas : la la En cortar

Adapter ilustracion. union una para unir los recta. seccion bullnose Engape cada6" angulos a dos con tivas Cuando secciones, de bullnose, como . primero pared use se