SRIXON Series Instruction Manual / Setting Adjustments

Part names and features P01 How to remove and install the QTS sleeve (torque wrenchP03 operation) How to remove and install the QTS sleeve (sleeve installation)P05 How to change tuning weights P07 CLEVELAND / SRIXON 5601 Skylab Rd., Huntington Beach, CA 92647, U.S.A. QTS sleeve performance guide P09 Tel:1-714-889-1300 Fax:1-714-889-5890 QTS sleeve position overview P11 / SRIXON CANADA Tuning weight performance guide P13 19099 25th Ave, #104 Surrey, BC, V3S 3V2, Canada Tel:1-604-542-0911 Fax:1-604-542-0955 Important Precautions—Please Read! P15 Part names and features Tuning weight Tuning weight Change weights for fine adjustment Change weights for fine adjustment of Center of Gravity (CG) height of CG depth and height

QTS sleeve QTS sleeve Change position to set desired Change position to set desired face angle, lie angle, and loft angle face angle, lie angle, and loft angle

745 Driver Weight port (center) Weight port (back) 945 Driver F45 Fairway wood 545 Driver

Accessories Custom torque wrench Custom pouch Use only the torque wrench and tuning weights provided. Use of damaged or improperly installed tuning weights may result in injury or product damage.

01 02 How to install and remove the QTS sleeve (Torque wrench operation) Hold the club upright with Supporting the in your hand, Loosen Tighten 1 the grip resting the ground. 2 gently insert the torque wrench 3 With the torque wrench aligned 4 With the torque wrench aligned into the screw hole. Use this position when loosening with the shaft, with the shaft, turn it clockwise and tightening. turn it counterclockwise. until you hear a 'click'.

Click

Shaft and torque Improperly aligned wrench should torque wrench * Be careful not to loosen the screw too much, form a straight line as you may drop the screw and lose the washer.

Do not use any tool other than the supplied torque wrench. Always tighten until you hear a 'click'. Also do not use the supplied torque wrench on any other products. Failure to tighten until you hear a 'click' may result in separation of the club head or product damage. Damaged QTS sleeve and/or improperly installed Once you hear a 'click', stop tightening. QTS sleeve may result in injury or product damage. * Not compatible with SRIXON Z-STAR series torque wrenches. Over-tightening may damage the QTS sleeve. Position the torque wrench so that it is correctly aligned with the shaft. Screws fastening the QTS sleeve employed on the driver Failure to insert the tip of the torque wrench firmly and fairway woods are designed for respective specifications into the screw hole may result in damage to the screw. and are not interchangeable. 03 04 How to remove and install the QTS sleeve (Sleeve installation) 5 Insert the shaft into the head 6 Insertion sample Align the position line with For right position For left position the ★ mark and press straight in. Align the ★ mark on the head with the 'R' Align the ★ mark on the head with the 'L' * Illustration shows neutral position on the QTS sleeve and press straight in. on the QTS sleeve and press straight in.

The shaft may not insert fully if the position line and sleeve mark are not correctly aligned. Press the shaft all the way in until the QTS sleeve is completely covered.

05 06 How to change tuning weights Pull the torque wrench directly Fix the desired tuning weight on the Locked Unlocked, 2 up to remove the weight. 3 tip of the custom torque wrench, mark on weight ready for removal * If the weight is difficult to remove even insert it into the weight port, aligned with mark on weight with the mark on the weight aligned and rotate it 45˚ clockwise to the “LOCK ” mark on head aligned with with the “ UNLOCK” mark on the head, “LOCK ” position to lock it. “ UNLOCK” mark on head lightly jiggle and pull the tuning weight at the same time with torque wrench * Do not turn the tuning weight past still inserted. the locked position. Hold the clubhead securely in one hand 1 and the custom torque wrench in the other. Insert the custom torque wrench straight into the hole in the center of the tuning weight and rotate it 45˚ counterclockwise to the “ UNLOCK” position to unlock it.

Do not use any tool other than the supplied torque wrench. Do not turn the tuning weight past the unlocked position. Also do not use the supplied torque wrench on any other products. Improper installation of the tuning weight may result in injury or product damage. Improper installation of the tuning weight may result in injury or product damage. Do not rotate more than 45˚. Ensure that the tip of the custom torque wrench is fully inserted When installing or removing the tuning weights, rotate them only 45˚ until they reach the into the hole of the tuning weight. “LOCK ” or “ UNLOCK” position respectively. Do not attempt to turn the weight more than 45˚, as it may damage either the tuning weight or the weight port. Hold both the custom torque wrench and the clubhead securely while exchanging the weights. 07 08 QTS sleeve performance guide Select from 12 different positions to set your preferred face angle, The sleeve is set to N (Neutral) at time of purchase. lie angle, and loft angle. Refer to the guide to set your preferred trajectory.

Lateral range of adjustment depending on sleeve position Flight path can be adjusted laterally by approx. 37 yards (W#1)

10 11 7 2 3 ihtaetr Low trajectory High trajectory

12 6

8 1 4

9 5

Approx. 37 yards Draw Fade 09 10 QTS sleeve position overview 1 Initial 2 3 4 5 6 7 8 9 10 11 12 oiinFc oiinn Lieangle Facepositioning Position

N R NU L Neutral Right Neutral Upright Left

Straight face Open face Straight face Closed face 0 -2.0 0 +2.0

Standard Moderate upright Upright Moderate upright 0 +1.0 +2.0 +1.0

11 12 Tuning weight performance guide 745 Driver 545 Driver 945 Driver Weight port (center) F45 Fairway wood Weight port (back)

Lowering the trajectory (when ball tends to rise) Raising the trajectory (when ball tends to drop) Lowering the trajectory (when ball tends to rise) Raising the trajectory (when ball tends to drop) A strong trajectory when hitting into the A high trajectory that delivers distance A strong trajectory when hitting into the A high trajectory that delivers distance wind and more distance with a run. with longer carry. wind and more distance with a run. with longer carry.

Installing a heavy weight lowers Installing a light weight raises Installing a light weight Installing a heavy weight the CG to deliver the CG to achieve on the back side on the back side Heavy a low-spin trajectory. Light the appropriate amount of spin. Light creates a shallower CG Heavy creates a deeper CG which reduces spin. that increases spin appropriately.

Trajectory—initial settingg T Trajectoryg after tuningTrajectory—initial settingg T Trajectoryg after tuning Trajectory—initial settingg T Trajectoryg after tuningTrajectory—initial settingg T Trajectoryg after tuning

13 14 Important To ensure a safe and satisfying golfingexperience, please be sure to follow these Important Precautions. Precautions Be sure to read the Important Precautions carefully and exerciseThe appropriate manufacturer care. assumes no liability for injury or product damage due to failure to comply with the instructions herein.

Before using Rules of Golf Carefully inspect the QTS sleeve and tuning weights prior to each round You may not change the QTS sleeve position of golf or practice session to confirm that they are properly secured. or exchange weights during a round. Check to see that the tuning weights are locked securely SRIXON Z Series clubs conform with R&A-approved Rules of Golf. However, it is against 1 in position. the rules to modify club performance during a round by changing the QTS sleeve position If the tuning weights are not secured firmly in the weight port and or exchanging weights to change the CG position, as this breaches the Rules of Golf regulation 4-2a, which states: “During a stipulated round, the playing characteristics of you swing the club during a game or practice session, there is a danger a club must not be purposely changed by adjustment or by any other means.” that a weight could fly off, injuring either you or a bystander.

Check to see that the QTS sleeve is properly secured. 2 Tighten the sleeve until you hear a 'click'. If you fail to properly secure the sleeve, there is a possibility that the head may come off in mid Confirm the weight is locked in positionUnlocked, ready for removal swing, injuring either you mark on weight aligned with mark on weight aligned with “LOCK ” mark on head “ UNLOCK” mark on head or a bystander. 15 16 Important To ensure a safe and satisfying golfingexperience, please be sure to follow these Important Precautions. Precautions Be sure to read the Important Precautions carefully and exerciseThe appropriate manufacturer care. assumes no liability for injury or product damage due to failure to comply with the instructions herein.

Care and storage

Only remove the QTS sleeve or tuning weights when making adjustments. If the QTS sleeve or weight ports become soiled 1 All parts should remain properly installed at all other times, 3 with water, dirt, or other debris, wipe them clean including when the club is in storage, to ensure that no foreign objects with a cotton swab or a soft, clean cloth. or debris become lodged in the sleeve connection or screw holes. Do not heat the QTS sleeve When removing the QTS sleeve or tuning weights, be sure 4 as it may damage the product. 2 that you do so in a clean location to ensure that no foreign objects or debris become lodged inside. Avoid adjusting the QTS sleeve or changing weights Installing the tuning weight while there are foreign objects 5 when the temperature is below -5˚C or above 45˚C, or debris in the weight port may damage either the weight as it may damage the plastic components in the weight port. or the port, or prevent proper installation or removal of the tuning weight. Please be aware that attempts to remove the QTS sleeve or intentionally It may even cause internal damage to the club head, 6 disassembling it may not comply with the manufacturer’s warranty. adversely affecting club performance. * For information on manufacturer's warranty regulations, please refer to the owner's manual and warranty included with your .

17 18