Instructions for P/N: 3164 Instructions for P/N: 3164 These clips will allow you to convert your pre 68 sedan or These clips will allow you to convert your pre 68 sedan or off-road chassis from the swing axle transmission design to off-road chassis from the swing axle transmission design to I.R.S. suspension. I.R.S. suspension.

These are for stock VW, I.R.S. trailing arms and do not apply These are for stock VW, I.R.S. trailing arms and do not apply to long travel (3x3) applications. We recommend that a to long travel (3x3) applications. We recommend that a qualified chassis fabricator do the installation. qualified chassis fabricator do the installation.

Fixtures are also available to aid you in the process. These are Fixtures are also available to aid you in the process. These are available to buy or rent from most off-road shops. available to buy or rent from most off-road shops.

For installations without a fixture you should install the stock For installations without a fixture you should install the stock I.R.S. arms that you intend to use on the car. Attach P/N: 3164 I.R.S. arms that you intend to use on the car. Attach P/N: 3164 clips to the arms and mock them up for fit on the torsion tube. clips to the arms and mock them up for fit on the torsion tube.

Since the years vary you will need to clearance the inside Since the years vary you will need to clearance the inside edges of the clips to fit against the horns of the transmission edges of the clips to fit against the horns of the transmission mount. The outer edge of the clip will be approximately 9" mount. The outer edge of the clip will be approximately 9" from the inside edge of the back of the torsion plate housing. from the inside edge of the back of the torsion plate housing. When the clips are in place you should have the clips with a When the clips are in place you should have the clips with a 10º angle downward to allow for proper travel before tack 10º angle downward to allow for proper travel before tack welding in place. welding in place.

Remove the trailing arm from the clips and weld in place. Remove the trailing arm from the clips and weld in place. 99-4162/0205 99-4162/0205

Instructions for P/N: 3164 Instructions for P/N: 3164 These clips will allow you to convert your pre 68 sedan or These clips will allow you to convert your pre 68 sedan or off-road chassis from the swing axle transmission design to off-road chassis from the swing axle transmission design to I.R.S. suspension. I.R.S. suspension.

These are for stock VW, I.R.S. trailing arms and do not apply These are for stock VW, I.R.S. trailing arms and do not apply to long travel (3x3) applications. We recommend that a to long travel (3x3) applications. We recommend that a qualified chassis fabricator do the installation. qualified chassis fabricator do the installation.

Fixtures are also available to aid you in the process. These are Fixtures are also available to aid you in the process. These are available to buy or rent from most off-road shops. available to buy or rent from most off-road shops.

For installations without a fixture you should install the stock For installations without a fixture you should install the stock I.R.S. arms that you intend to use on the car. Attach P/N: 3164 I.R.S. arms that you intend to use on the car. Attach P/N: 3164 clips to the arms and mock them up for fit on the torsion tube. clips to the arms and mock them up for fit on the torsion tube.

Since the years vary you will need to clearance the inside Since the years vary you will need to clearance the inside edges of the clips to fit against the horns of the transmission edges of the clips to fit against the horns of the transmission mount. The outer edge of the clip will be approximately 9" mount. The outer edge of the clip will be approximately 9" from the inside edge of the back of the torsion plate housing. from the inside edge of the back of the torsion plate housing. When the clips are in place you should have the clips with a When the clips are in place you should have the clips with a 10º angle downward to allow for proper travel before tack 10º angle downward to allow for proper travel before tack welding in place. welding in place.

Remove the trailing arm from the clips and weld in place. Remove the trailing arm from the clips and weld in place. 99-4162/0205 99-4162/0205