DOCSLIB.ORG

Instruction Manual 1710J Series Waveform Monitors (S/N B040000

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Instruction Manual 1710J Series Waveform Monitors (S/N B040000 Instruction Manual 1710J Series Waveform Monitors (S/N B040000 and above) 070-9673-03 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service. www.tektronix.com Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077 TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. WARRANTY Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations. This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product. THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES. Table of Contents General Safety Summary. xi Injury Precautions. xi Product Damage Precautions. xii Symbols and Terms. xii Certifications and Compliances. xii Service Safety Summary. xiii Getting Started Product Description. 1–1 Typical Configurations. 1–2 Accessories. 1–2 Standard Accessories. 1–2 Optional Accessories. 1–3 Installation. 1–3 Packaging. 1–3 Electrical Installation. 1–3 Power Source. 1–3 Mains Frequency and Voltage Ranges. 1–4 REMOTE Connector. 1–4 RGB/YRGB Parade Display. 1–4 Connecting to the Program Line. 1–4 Mechanical Installation. 1–6 Cabinets. 1–6 Cabinet Installation. 1–7 Rack Adapter. 1–8 Custom Installation. 1–10 Functional Checkout Procedure. 1–12 Procedure. 1–12 Operating Basics Front-Panel Controls and Indicators. 2–1 Rear-panel Connectors. 2–4 Making a Signal Amplitude Measurement. 2–5 Reference Graticules. 3–1 NTSC Composite Video Graticule Vertical Scales. 3–1 Horizontal Scales for NTSC and PAL Graticules. 3–3 PAL Graticule Vertical Scales. 3–3 Analyzing a Video Signal. 3–5 The Test Signal in the Video Signal. 3–5 The Creative Part of the Video Signal. 3–7 Specifications 1710J-Series Waveform Monitors i Table of Contents Theory of Operation Overview. 5–1 Block Diagram. 5–2 Vertical. 5–2 Horizontal. 5–2 CRT, Unblanking, and High Voltage. 5–3 Vertical Input, Diagram 1. 5–3 Input Amplifiers. 5–4 Channel Switch. 5–4 External Sync Input and Source Switch. 5–4 Sync Stripper. 5–5 Filter Selection. 5–6 Calibrator. 5–6 Vertical Output, Diagram 2. 5–7 Gain Cell. 5–7 Gain Cell Amplifier. 5–7 Second DC Restorer. 5–7 Switchable Gain Amplifier. 5–8 Vertical Output Amplifier. 5–9 Timing, Diagram 3. 5–9 Timing State Machine. 5–9 Horizontal Sync Generator. 5–10 Vertical Sync Generator. 5–11 Z-Axis Control. 5–11 Trace Rotation. 5–11 Graticule Illumination. 5–11 Regulators. 5–11 Sweep Generators and Horiz Output, Diagram 4. 5–12 Sweep Generator. 5–12 Magnifier Amplifier. 5–13 Horizontal Output Amplifier. 5–13 Microcontroller, Diagram 5. 5–13 Processor. 5–13 RGB Amplifier. ..
Load more

Recommended publications
  • WFM6100, WFM7000 and WFM7100 Waveform Monitors with Option FP ZZZ Quick Start User Manual
    xx WFM6100, WFM7000 and WFM7100 Waveform Monitors With Option FP ZZZ Quick Start User Manual www.tektronix.com 077-0085-00 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. Contacting Tektronix Tektronix, Inc. 14200 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA For product information, sales, service, and technical support: In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to find contacts in your area. Warranty 2 Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix. In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service.
    [Show full text]
  • WFM5200 Waveform Monitor Specifications And
    xx WFM5200 Waveform Monitor Specifications and Performance Verification ZZZ Technical Reference *P077053300* 077-0533-00 xx WFM5200 Waveform Monitor Specifications and Performance Verification ZZZ Technical Reference This document applies to firmware version 1.2 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service. www.tektronix.com 077-0533-00 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. Contacting Tektronix Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA For product information, sales, service, and technical support: In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to find contacts in your area. Warranty Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance.
    [Show full text]
  • Oscilloscope Fundamentals 03W-8605-4 Edu.Qxd 3/31/09 1:55 PM Page 2
    03W-8605-4_edu.qxd 3/31/09 1:55 PM Page 1 Oscilloscope Fundamentals 03W-8605-4_edu.qxd 3/31/09 1:55 PM Page 2 Oscilloscope Fundamentals Table of Contents The Systems and Controls of an Oscilloscope .18 - 31 Vertical System and Controls . 19 Introduction . 4 Position and Volts per Division . 19 Signal Integrity . 5 - 6 Input Coupling . 19 Bandwidth Limit . 19 The Significance of Signal Integrity . 5 Bandwidth Enhancement . 20 Why is Signal Integrity a Problem? . 5 Horizontal System and Controls . 20 Viewing the Analog Orgins of Digital Signals . 6 Acquisition Controls . 20 The Oscilloscope . 7 - 11 Acquisition Modes . 20 Types of Acquisition Modes . 21 Understanding Waveforms & Waveform Measurements . .7 Starting and Stopping the Acquisition System . 21 Types of Waves . 8 Sampling . 22 Sine Waves . 9 Sampling Controls . 22 Square and Rectangular Waves . 9 Sampling Methods . 22 Sawtooth and Triangle Waves . 9 Real-time Sampling . 22 Step and Pulse Shapes . 9 Equivalent-time Sampling . 24 Periodic and Non-periodic Signals . 10 Position and Seconds per Division . 26 Synchronous and Asynchronous Signals . 10 Time Base Selections . 26 Complex Waves . 10 Zoom . 26 Eye Patterns . 10 XY Mode . 26 Constellation Diagrams . 11 Z Axis . 26 Waveform Measurements . .11 XYZ Mode . 26 Frequency and Period . .11 Trigger System and Controls . 27 Voltage . 11 Trigger Position . 28 Amplitude . 12 Trigger Level and Slope . 28 Phase . 12 Trigger Sources . 28 Waveform Measurements with Digital Oscilloscopes 12 Trigger Modes . 29 Trigger Coupling . 30 Types of Oscilloscopes . .13 - 17 Digital Oscilloscopes . 13 Trigger Holdoff . 30 Digital Storage Oscilloscopes . 14 Display System and Controls . 30 Digital Phosphor Oscilloscopes .
    [Show full text]
  • Introduction to Video Measurements Using an MDO/MSO/DPO Series Digital Phosphor Oscilloscope
    Introduction to Video Measurements Using an MDO/MSO/DPO Series Digital Phosphor Oscilloscope Application Note Introduction measurement sets and vectorscopes. Many, however, can be made quickly and easily with a general-purpose Whether you’re troubleshooting a video installation or oscilloscope - providing that the instrument has the right designing a new set top box, making video measurements acquisition and measurement capabilities. can be a major challenge. Video waveforms are complex and frequently combine the signals that represent the video In this application note, we will examine critical video picture with the timing information necessary to display the measurement issues and show how they relate to the picture. The signals can be in a variety of different standards capabilities of different kinds of oscilloscopes. We will also and formats, each with its own characteristics. Some video demonstrate how to make common video measurements measurements require specialized instruments, such as using an MDO/MSO/DPO Series - MSO/DPO5000, industry-standard Tektronix waveform monitors, video MDO4000 and MDO3000 Series - digital phosphor oscilloscope. Application Note Conversion Processing Display Light Image Encoder Processing Decoding By Capture Standard R-Y Y B-Y Composite Video G R-Y Y B-Y B G B R Recording Matrix Conversion To Color Difference R Signals Monitor Digitizing DA R-Y B-Y Y Component Video Digital Processing R-Y M G a Analog t B Processing r B-Y i R Recording x Y Monitor Figure 1. Typical block diagram of a standard definition video system. Basic Video Standards and Formats Figure 1 shows a typical video system block diagram.
    [Show full text]
  • Color Correction for Video, Second Edition, by Steve Finland +41 52 675 3777 Hullfish and Jaime Fowler
    3 USING SCOPES AS CREATIVE TOOLS The next two important tools — after the video monitor itself — in analyzing a video image are a waveform monitor and vector- scope. There are three general categories of scopes available. The fi rst type is completely hardware based, with the waveform and vectorscope trace and graticule presented on a screen built into the scope (see Figure 3-2 ). The second type uses dedicated hard- ware to display the scopes on a separate computer display or as an overlay on your video monitor (see Figure 3-1 ). This is often referred to as a rasterizer or hybrid. The third type is soft- ware based using a video card, with the resulting image of the scope displayed in the software UI on your computer monitor (see Figure 3-3 ). Choosing Your Scope One of the main aspects that distinguish good scopes from bad is the resolution of the trace. One of the main aspects that distinguish good scopes from bad is the resolution of the trace. The trace, which is the scope ’ s visual representation of the video signal on the monitor, has a much higher resolution in hardware-based scopes and rasterizers. The resolution of the trace is particularly important when analyzing the video signal to be color corrected. This is where almost all software scopes — and even some hybrid scopes that are displayed on the video monitor — suffer. Hybrid scopes presented on a com- puter monitor are preferable to those presented on a video monitor because of the increased resolution possible with computer CRTs or LCDs.
    [Show full text]
  • WFM5200 Waveform Monitor User Manual I Table of Contents
    xx WFM5200 Waveform Monitor ZZZ User Manual *P077053103* 077-0531-03 xx WFM5200 Waveform Monitor ZZZ User Manual www.tektronix.com 077-0531-03 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. TandemVu® is a registered trademark of Tektronix, Inc. Contacting Tektronix Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA For product information, sales, service, and technical support: In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to find contacts in your area. Warranty Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix. In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service.
    [Show full text]
  • Robot Electronics Interface, Timer
    '01111411111 Wireles,. rld FEBRUARY 1986 95p Synchrodyne receiver Forth for control Compact disc mastering Loop aerial Australia A$ 3l5 Denmark DKr 38 00 Robot electronics interface, Germany Dm 7 50 Greece Dra 360 00 Netherlands DR 9 20 Italy L 4 /0 0 land NI$ 4 80 Sparn Pts 421) 00 Switzerland SFr 8 00 Remote-controlled timer Singapore . M$ J 00 USA $ 4 00 www.americanradiohistory.com 4i/ 1Â1401 IL :1G oiriTHE HIGH TECHNOLOGY TEST INSTRUMENTS OF THE FUTURE GRUNDIG OSCILLOSCOPES M020: 20MHz DUAL - CHANNEL M022: 20MHz DUAL- CHANNEL OSCILLOSCOPE OSCILLOSCOPE WITH AUTOMATIC TIME 20MHz Dual channel oscilloscope RANGE 2 mV /cm with full bandwidth 20MHz Dual channel oscilloscope Automatic peak-value trigger Automatic time base selection TV line and field triggering Soft tuning for fast manual adjustment Add and invert (Both channels invertable) Triggerable 2nd time -base, guarantees error Internal graticule and X -Y operation free 'zooming -in' This 20MHz dual -channel oscilloscope has Hold -off control and Z modulation advanced facilities, making it easy -to -use, with Plus all the advanced engineering of the M053: 50MHz DUAL - CHANNEL all the ruggedness and reliability to meet your M020 OSCILLOSCOPE go- anywhere testing needs. Included is a peak -value trigger to ensure stationary displays. 50MHz Dual channel oscilloscope Automatic Triggering facilities allow clear display of even time -base selection complex signal shapes. Alternating 2nd time -base for expanded traces £275 Digital display of time- bases, for unambiguous measurements Suits advanced applications in pulse, data and video technology A 50MHz dual -channel oscilloscope. Time -base range is automatically selected and shown on a digital display.
    [Show full text]
  • Keysight Logic and Protocol Analyzer Software
    Keysight Logic And Protocol Analyzer Software Dorian parachuted her infiltrators within, mechanical and equitable. Ed remains triapsidal: she organized her tailplanes misintend too adrift? Confutable Krishna neighbours poco. The back to detect sources and the flow through your time oscilloscope probe in concert within the keysight logic The link partner who purchased keysight streamline series of la probes logic analyzer logic and protocol analyzers can function to help you can be anything like to. If you get reviews, protocol for keysight logic and protocol analyzer software deskew tool. Agilent N5305A DE430019 Serial I A major useful debugging tool for digital. Computers electronics Software Keysight U4301 PCIe Gen3 Analyzer. Each pcie link training can carry it work with complete pci: software and logic analyzer protocol. Logic and serial protocol analyzers logic-signal sources arbitrary. We also has logic software package that the protocol analyzer is often challenging; data link no liability can write to your specific purposes including keysight logic and analyzer protocol software! Comidox CC2531 Sniffer USB Dongle Protocol AnalyzerBluetooth 4. Ltssm states corresponding to raise a test analyzer logic and protocol software solutions. Pcie Analyzer. If with want the protocol decoders on the Rigol which the PicoScope already known for. Fpga oscilloscope. Keysight Software Resources Keysight and MATLAB. Due to what is to comfortably manually analyze the keysight and bode plot on data processing to text box and digital signals outside of quad scan tool intended for keysight logic and protocol analyzer software! Ip cameras and software, keysight uses a circuitry under the actual signals! U4301AB U4421A U4431A and 1650 Series logic and protocol analyzers.
    [Show full text]
  • A Guide to Standard and High-Definition Digital Video Measurements
    Primer A Guide to Standard and High-Definition Digital Video Measurements 3G, Dual Link and ANC Data Information A Guide to Standard and High-Definition Digital Video Measurements Primer Table of Contents In The Beginning . .1 Ancillary data . .55 Traditional television . .1 Video Measurements . .61 The “New” Digital Television . .2 Monitoring and measuring tools . .61 Monitoring digital and analog signal . .62 Numbers describing an analog world . .2 Assessment of video signal degradation . .62 Component digital video . .2 Video amplitude . .62 Moving Forward from Analog to Digital . .3 Signal amplitude . .63 The RGB component signal . .3 Frequency response . .65 Gamma correction . .4 Group delay . .65 Gamma correction is more than correction for Non-linear effects . .66 CRT response . .5 Differential gain . .67 Conversion of R'G'B' into luma and color difference . .5 Differential phase . .67 The Digital Video Interface . .7 Digital System Testing . .67 601 sampling . .9 Stress testing . .67 The parallel digital interface . .11 Cable-length stress testing . .67 The serial digital interface (SDI) . .12 SDI check field . .68 High-definition video builds on standard In-service testing . .68 definition principles . .14 Eye-pattern testing . .70 Jitter testing . .72 Timing and Synchronization . .17 SDI status display . .76 Analog video timing . .17 Cable-length measurements . .76 Horizontal timing . .18 Timing between video sources . .77 Vertical timing . .20 Intrachannel timing of component signals . .78 Analog high-definition component video parameters . .24 Waveform method . .78 Timing using the Tektronix Lightning display . .78 Digital Studio Scanning Formats . .25 Bowtie method . .79 Segmented frame production formats . .25 Operating a Digital Television System . .81 Digital Studio Synchronization and Timing .
    [Show full text]
  • News from Rohde & Schwarz
    News from Rohde & Schwarz New test technology for module production Digital monitoring direction finders for HF to UHF ecoTV: solid-state transmitters set the pace in terms of economy 150 It is with deep sorrow that we say a last farewell to the highly esteemed senior partner and co-founder of our company Dr. phil. nat. Dr. E. h. Hermann Schwarz who passed away on 10 November 1995 at the age of 87. Executive Board, Company Management, Employees and Workers’ Council of ROHDE & SCHWARZ GmbH & Co. KG Dr. Hermann Schwarz, a pioneer of test and communication engineering “60 years Rohde & Schwarz – contributed to his decision to study they laid the foundation for the compa- 60 years of a life dedicated to Rohde natural sciences following grammar ny Rohde & Schwarz, an international & Schwarz” – this is the heading school in Nuremberg. He began his enterprise, which today employs more Dr. Hermann Schwarz chose for an studies of physics, mathematics and than 4,000 people and is still inde- article in “Zeitzeichen”, the inhouse geophysics in Heidelberg, continued pendent. magazine for Rohde & Schwarz in Munich - the time he spent here was employees, on the occasion of the certainly one factor in his decision to While R&D in the laboratory – with a company’s 60th anniversary. Now, set up business in this city a few years focus on impedance and dissipation- only two years later, this life has later – and finished in Jena, where he factor measurements – still made up ended. Dr. Dr. E. h. Hermann Schwarz attended lectures by Prof. Esau and the bulk of Hermann Schwarz’s work passed away in his 88th year on the Max Wien, met his future friend and in the first few years, he was also from evening of 10 November 1995.
    [Show full text]
  • SALES and SERVICE SYSTEM Service Network with Sales Representatives Stationed in 62 Countries/Areas FINLAND
    SALES AND SERVICE SYSTEM Service Network with Sales Representatives Stationed in 62 Countries/Areas FINLAND NORWAY JAPAN LEADER ELECTRONICS CORP. SWEDEN 2-6-33, Tsunashima-Higashi, Kohoku-ku, Yokohama 223-8505, Japan PHONE: 81-45-541-2123 FAX: 81-45-541-2823 THE NETHERLANDS UNITED KINGDOM RUSSIA LEADER ELECTRONICS EUROPEAN OFFICE Nijverheidsweg 15, 5627BT Eindhoven, ESTONIA Regional Office CHINA (Beijing) The Netherlands LITHUANIA LEADER ELECTRONICS CORP. BEIJING IRELAND OFFICE PHONE: 31-40-2565008 DENMARK FAX: 31-40-2565009 Unit 08, 6th floor of Tower B, BEIJING COFCO PLAZA No.8 Jianguomennei Dajie BELGIUM CZECH Dongcheng District, Beijing 100005, P.R. China FRANCE PHONE: 86-10-8511-8606, 8511-8607 GERMANY AUSTRIA FAX: 86-10-8511-8606 KOREA SWITZERLAND SPAIN ITALY SYRIA BANGLADESH PORTUGAL PAKISTAN THAILAND GREECE JORDAN CANARY Is. VIETNAM TUNISIA KUWAIT NEPAL EGYPT TAIWAN MOROCCO ISRAEL INDIA OMAN PHILIPPINES SAUDI ARABIA UNITED ARAB EMIRATES GHANA SRI LANKA BRUNEI CHINA (Shanghai) MALAYSIA Leader Electronic Corp. has focused its LEADER SHANGHAI TECHNICAL SINGAPORE attention on international markets from the SERVICE CENTER No.776 Qinzhou Road(SOUTH), INDONESIA beginning. Shanghai,CHINA Zip Code 200233 Regional Office CHINA (Dongguan ) LEADER established local corporations in PHONE: 86-21-64517655, 64083038 LEADER INSTRUMENTS (H. K.) LTD. U.S.A. in 1969, in Hong Kong in 1980. FAX: 86-21-64083038 DONGGUAN OFFICE 9G, Tower B, Lianjian Trade Building, Many other positive measures have also been Dongguan Station, changping, AUSTRALIA dongguan, Guangdong Province, China taken before other companies. PHONE: 86-769-83829-381, 83829-391 In July 1995, LEADER’s own service center SOUTH AFRICA FAX: 86-769-3819-289 was set up at Shanghai for better service/ maintenance in China.
    [Show full text]
  • Primer > a Guide to Standard and High-Definition Digital Video
    Digital Video Measurements A Guide to Standard and High-Definition Digital Video Measurements A Guide to Standard and High-Definition Digital Video Measurements Primer A Guide to Standard and High-Definition Digital Video Measurements Contents In The Beginning · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 1 Traditional television · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 1 The “New” Digital Television · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Numbers describing an analog world · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Component digital video · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Moving Forward from Analog to Digital · · · · · · · · · · · · · · · · · · · · · · · · · · 3 The RGB component signal · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Gamma correction · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 Gamma correction is more than correction for CRT response · · · · · · · · · · · · · · · · · · · · · · · 5 Conversion of R'G'B' into luma and color difference · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5 The Digital Video Interface · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7 601 sampling · · · · · · · · · · · · · · · · · · · ·
    [Show full text]