Trim-17” x 22”

FAS2050 System Installation and Setup

1 Before you begin 2 Unpack and verify contents If you have not already done so, gather the required information and confirm your site Your system comes with an accessory kit that includes the following components: requirements, as described in the Site Requirements Guide at http://now.netapp.com/. - This installation poster - Power cables - Software license flyer - DB-9 to RJ-45 console adapters - System Manager CD-ROM - Rail kit (for two-post and four-post racks) - Grounding kit

3 Install in rack Caution: Only use the NetApp® rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system. Four-post rack

(2x) Clip nut (2x) tool

(4x) Note: Remove handles after the system is supported by the shelf.

Setting the Disk Shelf IDs

Front rail 1 (2x)

Clip nut (4x)

4U

0 FRONT SIDE 3U

3U Shelf ID switch

Note: The disk shelf IDs for the 1 disk shelves should be set in the range 1 to 6. Leave the FAS2050 1 disk shelf ID at the preset value of 00. Note: Refer to the rail kit installation flyer included with the rail kit for the two-post procedure. 4 Cable the system Cable controllers Cable disk shelves Connect power 1 RJ-45 to DB-9 adapter to console port (required) These are a few common configurations. For additional options, see Supported Configurations for Note: You do not need to FAS2000-series Systems at http://now.netapp.com. ground your system. 0a 0b e0a e0b Port labels Active/Active NAS or ISCSI: Active/Active SAN: 4 FCP 1 Disk Shelf Stack (Multipath) Connections 1 Fibre Channel Disk Shelf Stack (Multipath) 1 1 8 Remote Controller to shelf Controller to switches

Management FAS2050 1b 1a Port 0a 0b 10101 e0a e0b PSU PSU CM-B 1b 1a FAS2050 1b 1a 0a 0b 10101 e0a e0b 0a 0b 10101 e0a e0b PSU PSU CM-B 1b 1a 2 0a 0b 10101 e0a e0b Console cable to adapter DS14 Fibre OUT IN or DS14 Channel OUT IN 0a 0b e0a e0b PSU PSU IN OUT PSU PSU IN OUT

DS14 8 OUT IN DS14 OUT IN PSU PSU PSU PSU IN OUT IN OUT

Console 2 Shelf to shelf 2 Controller to shelves

FAS2050 1b 1a 0a 0b 10101 e0a e0b PSU PSU 3 Network cables to e0a and e0b ports CM-B 1b 1a FAS2050 1b 1a 0a 0b 10101 e0a e0b 0a 0b 10101 e0a e0b PSU PSU CM-B 1b 1a 0a 0b e0a e0b 0a 0b 10101 e0a e0b DS14 OUT IN DS14 PSU PSU OUT IN 8 IN OUT PSU PSU IN OUT

DS14 OUT IN DS14 OUT IN PSU PSU PSU PSU IN OUT IN OUT

3 Shelf to controller 3 Shelf to controller 4 Network cable to Remote Management port FAS2050 1b 1a 0a 0b 10101 e0a e0b PSU PSU CM-B 1b 1a FAS2050 1b 1a 0a 0b 6 e0a e0b 0a 0b 10101 e0a e0b 0a 0b 10101 e0a e0b PSU PSU CM-B 1b 1a 0a 0b 10101 e0a e0b DS14 8 8 OUT IN DS14 PSU PSU OUT IN IN OUT PSU PSU IN OUT

DS14 210-03951+C0 OUT IN DS14 OUT IN PSU PSU IN OUT PSU PSU IN OUT 5 Connect the installed PCI card, as needed. 5 Boot the system and proceed with setup - Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate. - Windows® environments with DHCP: Install System Manager from the CD-ROM and run it on a Windows client system to discover, configure, and manage your system. Connect your Windows client system through the management LAN. - All other configurations: Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/. Copyright © 2009 NetApp, Inc. All rights reserved. Trim-17” x 22”

Hardware Overview of the FAS2050 System

Appliance rear 2 power Second Appliance front 0 to 20 supplies controller disk drives module (for active/active Drive 0 Disk drive, System LEDs configurations power, and only) Power Controller fault LEDs Fault module PCI slot Drive 19 Controller 2 Fibre Channel ports 2 network ports A Activity RM (Remote Management) port Controller B Activity Console port x4 Filler panel

Shutting down a controller module Attention: Shut down the target controller module (called a “node” in an CAUTION LIFTING HAZARD active/active configuration) by completing the applicable For hot-swappable FRUs: procedure: Use assistance Always consult http://now.netapp.com for If you have an active/active configuration: when moving or current field-replaceable unit (FRU) replacement procedures. 1. Check the status of the target node by entering the following lifting the equipment. command at the system console of either node: Adding external storage or using FCP: cf status You must order and use SFP modules on 2. Take one of the following actions, depending on the result of your system, if you are connecting external the cf status command: Fibre Channel storage devices or using FCP IF clustering is enabled and neither node is in takeover with the system. mode, go to step 3. IF clustering is enabled and the partner node took over the Disk drive Attention: target node, go to “Opening the System.” For hot-swappable power supplies: IF clustering is enabled and the target node took over the The system shuts down two minutes after partner node, correct the problem, run the cf giveback Power supply command from the target node console, and go back to you remove a power supply. step 1.

3. Take over the target node by entering the following command from the partner node’s console: partner> cf takeover 4. Go to “Opening the System” when the takeover is complete.

If you have a single-controller configuration: 1. Enter the following command from the system console: Releasing a disk drive cam handle halt 2. Turn off the power supplies and unplug both power cords from the power source. Controller module 3. Check the nonvolatile memory (NVMEM) LED. Cam handle IF the LED is not flashing, go to “Opening the System.” IF the LED is flashing, there is content in the NVMEM that has not been saved to disk. Reconnect the power supplies to Attention: Disk drives are fragile. Do not handle them except when replacing failed disk drives or moving them the power source, reboot the controller module, and repeat Thumbscrew Steps 1 through 3. If repeated attempts to cleanly shut down to a new chassis. the controller module fail, be aware that you might lose any Controller module data that was not saved to disk. Go to “Opening the cover System.” Closing the system Battery 1. Align the controller module cover with the notches on the Opening the system Indentation sides of the controller module, then slide the cover down and forward to seat it. 1. Properly ground yourself. 2. Align the end of the controller module with the opening in 2. Loosen the thumbscrew on the controller module the chassis. cam handle. 3. Gently push the controller module halfway into the 3. Remove any cabling from the controller module. Make Battery DIMMs chassis and recable the controller module, then push the sure that you keep track of where the cables were cover controller module all the way into the chassis. connected to the controller module. Result: For systems in an active/active configuration, the 4. Pull the controller module cam handle downward and node reboots as soon as you seat the controller module slide the controller module out of the system. Make sure completely into the chassis. that you support the bottom of the controller module with 4. Firmly push up the cam handle to finish seating the your free hand. controller module in the system, and then push the cam 5. Remove the controller module cover by completing the handle to the closed position and tighten the following substeps, using the illustration for reference: thumbscrew on the cam handle. Thumbscrew Locking a. Loosen the thumbscrew on the back of the Nut 5. Complete the boot process. controller module. PCI access b. Gently press the heel of your hand on the indentation IF your system has a single controller module, plug in in the controller module cover closest to the cam panel the power supply and turn on the power. handle, then slide the cover toward the back of the PCI card IF your system is in an active/active configuration, wait a module. CompactFlash® card few seconds for the node to boot, then enter the c. Lift the cover straight up off the controller module. following command from the partner console: cf giveback