Software Configuration Guide SmartWare Release 2.10 Customer Deliverable Documentation Part Number 80-0151 English Revision 1.00, October 31, 2002 2 Legal Notice Software Configuration Guide Release 2.10, Revision 1.00 Legal Notice 3 LEGAL NOTICE Copyright ©2002 Inalp Networks AG All rights reserved. No part of this publication may be reproduced without prior written permission from Inalp Networks AG. Inalp Networks AG reserves the right to make changes in specifications and other information contained in this document without prior notice. The information provided is subject to change without notice. In no event shall Inalp Networks AG or its employees and associated companies be liable for any incidental, special, indirect or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained within it, even if Inalp Networks AG has been advised of, known, or should have known, the possibility of such damages. Inalp, the Inalp logo, and SmartNode are registered trademarks of Inalp Networks AG. SmartWare and SmartView Management Center are trademarks of Inalp Networks AG. All other trademarks mentioned in this document are property of their respective owners. EU Declaration of Conformity The EU Directives covered by this Declaration 99/5/EC Guideline of the European Parliament and the Committee for the Harmonization of the Legal Regulations of the Member States concerning radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. The Products covered by this Declaration The products covered by this declaration are the SmartNode 1000 and 2000 family series devices. The Basis on which Conformity is being Declared The products identified above comply with the requirements of the above EU directives by meeting the following standards: • Safety Compliance: EN 60950 (Edition 1997) • EMC Compliance: EN 55022 (Edition 1998), EN 55024 (Edition 1998) • ISDN Terminal Equipment Requirements (BRI): ETS TBR3 (Edition 1999) • ISDN Terminal Equipment Requirements (PRI): ETS TBR4 (Edition 1999) The CE mark was first applied in 2000. Inalp Networks AG Meriedweg 7 CH-3172 Niederwangen Software Configuration Guide Release 2.10, Revision 1.00 4 Table of Contents TABLE OF CONTENTS 1 Terms and Definitions................................................................................................16 1.1 Introduction.......................................................................................................................................16 1.2 SmartWare Architecture Terms and Definitions..........................................................................16 2 Applications..................................................................................................................23 2.1 Introduction.......................................................................................................................................23 2.2 Carrier Networks..............................................................................................................................23 2.3 Enterprise Networks ........................................................................................................................24 2.4 LAN Telephony ................................................................................................................................25 3 System Overview .........................................................................................................27 3.1 Introduction.......................................................................................................................................27 3.2 SmartNode Hardware Platforms....................................................................................................28 3.3 SmartWare Embedded Software ....................................................................................................29 3.4 SmartView Management Center Tools..........................................................................................30 4 Configuration Concepts..............................................................................................31 4.1 Introduction and Overview.............................................................................................................31 4.2 Contexts and Gateways ...................................................................................................................32 4.2.1 Context .......................................................................................................................................32 4.2.2 Gateway .....................................................................................................................................32 4.3 Interfaces, Ports and Bindings ........................................................................................................32 4.3.1 Interfaces....................................................................................................................................32 4.3.2 Ports and Circuits .....................................................................................................................33 4.3.3 Bindings .....................................................................................................................................33 4.4 Profiles and Use commands............................................................................................................33 4.4.1 Profiles........................................................................................................................................33 4.4.2 Use Commands.........................................................................................................................34 5 Command Line Interface............................................................................................35 5.1 Command Modes .............................................................................................................................35 5.1.1 System Prompt..........................................................................................................................36 5.1.2 Navigating the CLI ...................................................................................................................37 5.2 Command Editing ............................................................................................................................39 5.2.1 Command Help.........................................................................................................................39 5.2.2 The No Form .............................................................................................................................39 5.2.3 Command Completion ............................................................................................................39 5.2.4 Command History....................................................................................................................39 5.2.5 Command Editing Shortcuts...................................................................................................39 6 Accessing the Command Line Interface..................................................................41 6.1 Introduction.......................................................................................................................................41 6.2 Warning .............................................................................................................................................41 6.3 Accessing the SmartWare Command Line Interface Task List ..................................................41 6.4 Accessing via the Console Port.......................................................................................................42 6.4.1 Console Port Procedure ...........................................................................................................42 6.5 Accessing via a Telnet Session........................................................................................................42 6.5.1 Telnet Procedure.......................................................................................................................43 6.6 Log On to SmartWare ......................................................................................................................44 6.6.1 Warning .....................................................................................................................................44 6.7 Selecting a Secure Password ...........................................................................................................44 6.8 Configure Operators and Administrators.....................................................................................45 6.9 Factory Preset Administrator Account..........................................................................................45 6.10 Create an Operator Account ...........................................................................................................45 6.11 Create an Administrator Account ..................................................................................................46 6.12 Displaying the CLI Version.............................................................................................................46 Software Configuration Guide Release 2.10, Revision 1.00 Table of Contents 5 6.13 Display Account Information .........................................................................................................47