GM of Canada OnStar® Cellular Communication Upgrade 2000-2014 GM Passenger Cars and Light Duty Trucks 2015 Buick Enclave 2015 Cadillac Escalade Models (Built W/O VV4) 2015 Chevrolet Camaro, Express, Traverse 2015 Chevrolet Silverado 2500/3500, Suburban, Tahoe (Built W/O VV4) 2015 GMC Acadia, Savana 2015 GMC Sierra 2500/3500, Yukon Models (Built W/O VV4) 2005-2010 Pontiac Vibe Equipped with OnStar® (RPO UE1) This Bulletin does not apply to vehicles equipped with RPO UE0. This Bulletin has been revised to add the Pontiac Vibe Model, a Note for Voice Issue PI1533 reference, Vibe Replacement and Programming Instructions and a table under Step 9 of Model Year 2010 and Older Repair Instructions. Please discard Corporate Bulletin Number 15-08-44-001E. Canadian Upgrade Program Overview Canadian wireless service providers plan to decommission their 2G Code Division Multiple Access (CDMA) network through 2015. OnStar® currently depends on active and functioning 2G CDMA networks to deliver services. As a result, in order to continue to provide OnStar® services without interruption, Canadian vehicles that do not have OnStar® 3G/4G LTE will need a hardware upgrade. In order to upgrade their vehicle hardware and continue receiving OnStar® services, a customer will receive a letter from OnStar® with instructions for the upgrade process when the hardware is available for installation on their vehicle. There are different versions of hardware required for vehicles that will be available at different times in early 2015, so it is important that customers first receive the communication from OnStar® to begin the upgrade process. Note Refer to PI1533 for additional repair instructions that may be required for select models to ensure proper handsfree voice recognition performance. Software Calibrations within the Procedures Below that MUST be Completed before Proceeding with this Bulletin: Volt and ELR 2011-2014 Chevrolet Volt and 2014 Cadillac ELR – #PIC5920: Vehicle Will Not Charge And Hybrid Loss Of Isolation With DTC P0AA6 Note 2011-2014 Chevrolet Volt and 2014 Cadillac ELR — the HPCM2 and BECM Must Be updated with the latest calibrations available on TIS2WEB prior to proceeding with OnStar® cellular communication upgrade. Use the unique labor operation in the #PIC5920. 2011-2012 Chevrolet Volt – #11342E: Customer Satisfaction - Enhancements for Side Impact Pole Performance All Vehicles with Radio RPOs IO3, IO4, IO5, IO6, or (RAO – UA3) 2013-2015 Vehicles with radio RPOs IO3, IO4, IO5, IO6, or (RAO – UA3) (ATS Base Radio) – use latest version of PI1238: No XM on Start-Up when Manually Tuned and/or Using Voice Recognition, No Radio Wake-Up Note 2013-2015 Vehicles with radio RPO’s IO3, IO4, IO5, IO6, or (RAO-UA3) (ATS Base Radio) Ensure that the radio has the latest calibration available on TIS2WEB prior to proceeding with the OnStar® cellular communication upgrade. As stated in this PI, the “Audio Soft Version” label should be 000474 or lower before continuing. If version 000477 is already installed, reprogramming is not necessary. DO NOT reprogram. Software corruption may occur. Use the unique labor operation in the #PI1238. Please Be Sure To Read These Important Guidelines: The customer must accept OnStar’s “User Terms, Privacy Statement and Software Terms" in order to get the hardware upgrade. The customer can provide their acceptance at www.onstar.ca by logging into their OnStar® account. After accepting the OnStar® User Terms and Conditions the customer will need to call the OnStar® call center to begin the ordering process. English/French: 1-877-935-8717 Some customers will be required to purchase a 1-year, non-refundable OnStar® Service Plan at the regular retail price (no discounts are available): 1-year OnStar Protection Plan: $249.90 + tax 1-year OnStar Security Plan: $299.90 + tax 1-year OnStar Guidance Plan: $399.90 + tax The 1-year OnStar® Service Plan is non-refundable or transferable to another person. Upgrades can apply unused subscription months to a new or Certified Pre-Owned OnStar® equipped GM vehicle purchase or lease prior to the expiration date. Hardware will be ordered and shipped to the customers selected dealer for installation. Hardware upgrade sets are VIN specific and must be installed on the vehicle that the set was ordered for. Actual odometer reading must be used on the Repair Order (RO). Note DO NOT estimate the odometer reading of the vehicle. Customers will receive a new Hands-Free Calling number once the new hardware is installed and configured. Any nametags that were stored in the old system will need to be reset by the subscriber once the new hardware is installed. Customers are responsible for the charges described in the communication from OnStar® regardless of whether their vehicle is in or out of the New Vehicle Warranty period. In addition, customer should not be charged labor costs. Dealers can charge GM the labor for the upgrade as specified at the end of this bulletin used the listed labor operation. All GM vehicles built in 2000 and after, and that are equipped with digital hardware, are eligible for an OnStar® hardware upgrade. Aftermarket Equipment Installed Prior to starting the upgrade the technician should inspect the radio to verify that the GM original equipment radio is present and functioning. If an aftermarket radio, navigation, amplifier, or bluetooth has been hard-wired into the vehicle, ensure that the Service Advisor is aware and the customer has approved to go ahead with the upgrade given the risk that their aftermarket accessory and/or OnStar® might not work after the upgrade has been completed. Note The following statement was presented to the customer in their original offer communication. Part Ordering Process – Active OnStar® Subscribers To upgrade their vehicle to an OnStar® 4GLTE (Generation 10) or 3G (Generation 9.4) system, the customer must do the following: 1. Currently have an active OnStar® service plan. 2. Have received an upgrade communication letter from OnStar®. Note OnStar® will communicate to subscribers when their specific hardware is available. Not all hardware types will be available at the start of the program. 3. Go to the website www.onstar.ca and sign into their OnStar® Account to accept OnStar’s “User Terms, Privacy Statement and Software Terms.” 4. Contact OnStar® to initiate the hardware order: “User Terms, Privacy Statement and Software Terms” must be accepted prior to ordering hardware. English/French 1-877-935-8717 5. Purchase a one year (annual) service plan (as required) on the OnStar® website or through the OnStar® Advisor. Service Plan is non-refundable, when required. Current Basic Plan, 2014 Remotelink Key Fob Service, and Factory Trail Service customers may not require a commitment. Unused portions of the annual package is transferable to a new OnStar® 4G LTE equipped vehicle. 6. Wait for selected Dealer to schedule an appointment with the customer. Take the vehicle to the dealership on the appointment date for the hardware installation and activation. Part Ordering Process and Hardware Installation – New Unsold Vehicles on Dealers Lot 1. Dealers will automatically receive OnStar® hardware upgrade kits for affected dealer new vehicle inventory beginning spring 2015. Note Not all upgrade modules will be available at program launch, modules will be release for dealer inventory when they are available. Upgrade kits are VIN specific, installing a kit in another vehicle will cause configuration issues and might result in damaging the module. 2. Dealer will be provided a summary by e-mail of the parts being shipped (FEDEX) to their dealership from York Electronics. Note On reviewing the list, if the vehicle is no longer in the dealer inventory (either due to sale or dealer trade) contact York by phone, e-mail, or fax to get a Return Material Authorization. Parts should not be forwarded to the dealer or installed in the customer’s vehicle. York Contact Information: Eastern Canada Phone: English 1-888-650-9675 ext. 307 Phone: French 1-888-650-9675 ext. 302 Fax: 1-888-650-9677 E-mail: [email protected] Western Canada Phone: 1-800-361-2894 ext. 1 Fax: 1-800-361-5396 E-mail: [email protected] 3. Technician will install parts, program the module using Service Programming System (SPS) available on TIS2WEB and confirm connection. Service Technician will follow the installation instructions below. 4. If successful, the technician will simply verify activation is complete. Upon confirmation of successful hardware installation, apply the OnStar® 4G Wi-Fi sticker to the vehicle near the price and fuel economy label, the vehicle is ready for sale. Note These vehicles will not behave exactly like those with factory installed modules. The OnStar® activation message will begin to play once the vehicle is driven 1.6 km (1 mile) and will play at each key cycle until the vehicle is sold and the customer has accepted the OnStar® User Terms, Privacy Statement and Software Terms. For some vehicles the OnStar® icon on the radio display screen will be grayed out and inactive after the upgrade. This icon becomes active once an active OnStar® account is added to the vehicle. It is important to note that the Wi-Fi feature will be active and can be used in demonstrations. Customer Hardware Upgrade To complete the hardware upgrade for a customer’s vehicle to an OnStar® 4G LTE (Generation 10) or 3G (Generation 9.4) system, the dealership will complete following below: 1. Direct all customer questions to OnStar®. If the customer has received the upgrade letter and they have additional questions, they can call OnStar® at 1-877-935-8717 (English/French) or by pressing their blue button. 2. Dealers will be notified daily by e-mail of orders placed for their dealership with related customer contact information.