http://msdsreport.com/msds/BVXFN MAPP GAS MSDS Number BVXFN National Stock Number 6830-00D003384 Product Name MAPP GAS Manufacturer BERNZOMATIC CORP Product Identification Product ID:MAPP GAS MSDS Date:09/10/1993 FSC:6830 NIIN:00D003384 MSDS Number: BVXFN Responsible Party BERNZOMATIC CORP ONE BERNZOMATIC DRIVE MEDINA , NY 14103 US Emergency Phone: 716-798-4949 Info Phone: 716-798-4949 Preparer: ROGER MAXON Cage: 70785 Contractor BERNZOMATIC CORP MEDINA, NY 14103-1648 US 716-798-4949 Cage: 70785 Ingredients LPG (LIQUEFIED PETROLEUM GAS) CAS: 68476-85-7 RTECS: SE7545000 Fraction By Weight: 56.0% OSHA PEL1000 PPM ACGIH TLV: 1000 PPM; 9394 METHYL ACETYLENE-PROPADIENE MIXTURE (MAPP) CAS: 59355-75-8 RTECS: UK4920000 Fraction By Weight: 44.0% OSHA PEL1000PPM http://msdsreport.com/msds/BVXFN ACGIH TLV: 1000PPM/1250STEL; 94 Hazards LD50 LC50 Mixture:LD50 (ORAL RAT) IS NOT RELEVANT. Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO Health Hazards Acute and Chronic:TARGET ORGANS:LUNGS & CNS. ACUTE & CHRONIC- ASPHYXIANT. MAY CAUSE DIZZINESS, HEADACHE, EXCITATION & UNCONSCIOUSNESS. EYES:LIQUID GAS MAY CAUSE FROSTBITE. SKIN:LIQUID MAY CAUSE FROSTBITE. ORAL:NOT LIKE LY, BUT LIQUID CAN CAUSE LIPS & MOUTH FROSTBITE. Explanation of Carcinogenicity:NONE Effects of Overexposure:EYE AND SKIN FROSTBITE; HEADACHE, DIZZINESS, UNCONSCIOUSNESS First Aid First Aid:GET MEDICAL HELP IF SYMPTOMS PERSIST. INHALED:REMOVE TO FRESH AIR. PROVIDE CPR/OXYGEN IF NEEDED. EYES:FLUSH WITH WATER FOR 15 MINUTES, HOLDING EYELIDS OPEN. SEEK ADVICE OF AN OPHTHALMOLOGIST, URGENTLY . SKIN:FOR EXPOSURE TO LIQUID, FLUSH WITH WATER & WARM FROSTBITE AREAS WITH WARM WATER (NOT TO EXCEED 105F). ORAL:IF LIQUID IS SWALLOWED, DO NOT INDUCE VOMITING. CALL A PHYSICIAN. Fire Fighting Flash Point Method:CC Flash Point:-99F TO -127F Lower Limits:3.0 Upper Limits:11.0 Extinguishing Media:COOL CYLINDER WITH WATER. ELIMINATE OXYGEN SOURCE OR STOP FLEW OF GAS. USE DRY CHEMICAL/CARBON DIOXIDE TO REDUCE OXYGEN. Fire Fighting Procedures:ONLY SAFE WAY TO EXTINGUISH FIRE IS TO STOP FLOW OF GAS. IF FLOW CANNOT BE STOPPED, LET FIRE BURN ITSELF OUT WHILE COOLING CONTAINERS WITH WATER. STAY UPWIND. Unusual Fire/Explosion Hazard:EXTREMELY FLAMMABLE AND EXPLOSIVE. Accidental Release Spill Release Procedures:WEAR PROTECTIVE EQUIPMENTS. VENTILATE AREA. REMOVE ALL SOURCES OF IGNITION, STOP LEAK AND REMOVE LEAKING CONTAINERS IF YOU CAN DO WITHOUT RISK. REDUCE VAPORS WITH WATER FOG. BEFORE ENTERING AREA, ESPE CIALLY CONFINED AREA, CHECK ATMOSPHERE WITH DEVICE Neutralizing Agent:NOT RELEVANT Handling Handling and Storage Precautions:STORE CYLINDERS SECURED, IN UPRIGHT POSITION. STORE IN WELL VENTILATED AREA AWAY FROM IGNITION SOURCES, DIRECT SUNLIGHT, OXYGEN & OTHER OXIDIZERS. Other Precautions:EXTREMELY FLAMMABLE. STORE AND USE WITH ADEQUATE VENTILATION. CLOSE VALVE WHEN NOT IN USE. NEVER WORK ON A PRESSURIZED SYSTEM. GAS CAN CAUSE RAPID SUFFOCATION. KEEP OUT OF REACH OF CHILDREN. Exposure Controls Respiratory Protection:NONE REQUIRED WHERE ADEQUATE VENTILATION CONDITIONS EXIST. IN EMERGENCY OR CONFINED AREA, WEAR NIOSH-APPROVED SELF CONTAINED BREATHING APPARATUS. Ventilation:MECHANICAL (GENERAL AND/OR LOCAL EXHAUST, EXPLOSION-PROOF) VENTILATION TO MAINTAIN EXPOSURE BELOW TLV. Protective Gloves:LEATHER OR WELDER'S GLOVES RECOMMENDED Eye Protection:SAFETY GLASSES OR WELDER GOGGLES Other Protective Equipment:LEATHER SLEEVES, LEATHER APRON AND OTHER STANDARD PROTECTIVE EQUIPMENT FOR CUTTING AND WELDING Work Hygienic Practices:OBSERVE GOOD PERSONAL HYGIENE PRACTICES AND RECOMMENDED PROCEDURES. Supplemental Safety and Health HANDLE CYLINDERS WITH CARE. FUMES AND GASES FROM WELDING CANNOT BE http://msdsreport.com/msds/BVXFN CLASSIFIED SIMPLY. TRAIN WORKERS TO KEEP THEIR HEADS OUT OF FUMES. Chemical Properties HCC:G2 NRC/State Lic Num:NOT RELEVENT Boiling Pt:B.P. Text:-36F TO -4F Vapor Pres:6410 @70F Vapor Density:1.48 Spec Gravity:0.571 Evaporation Rate & Reference:NOT RELEVANT Solubility in Water:SLIGHT Appearance and Odor:COLORLESS, UNPLEASANT ODOR AT APPROXIMATELY 100 PPM Percent Volatiles by Volume:100 Stability Stability Indicator/Materials to Avoid:YES AVOID UNCONTROLLED CONTACT WITH OXIDIZERS. Stability Condition to Avoid:TEMPERATURE ABOVE 125F. Disposal Waste Disposal Methods:VENT TO ATMOSPHERE IN OUTDOOR AREA FREE OF ALL SOURCES OF IGNITION. KEEP PERSONNEL AWAY. DISCARD ANY PRODUCT, RESIDUE, DISPOSABLE CONTAINER OR LINER IN AN ENVIRONMENTALLY ACCEPTABLE MANNER, IN FULL CO MPLIANCE WITH LOCAL, STATE AND FEDERAL REGULATIONS Disclaimer (provided with this information by the compiling agencies): This information is formulated for use by elements of the Department of Defense. The United States of America in no manner whatsoever, expressly or implied, warrants this information to be accurate and disclaims all liability for its use. Any person utilizing this document should seek competent professional advice to verify and assume responsibility for the suitability of this information to their particular situation..