BELL SYSTEM PRACTICES SECTION 503-200-1 08 AT&TCo Standard Issue 2, March 1976 TELEPHONE SETS 881A102, 8818102, 881A103, 8818103, 881A104, AND 8818104 1. GENERAL 1.01 This section provides identification, installation, and connection information for the 881A102 (MD), 881B102, (Antique Gold**, Fig. 1); 881A103 (MD), 881B103, (Mediterranean**, Fig. 2), and 881A104 (MD), 881B104 (Early American**, Fig. 3) DESIGN LINE* telephone (Cradle Phone) sets. *Trademark AT&TCo. • *Trademark American Telecommunication Corporation 1.02 This section is reissued to: • Add information on the 881B102, 881B103, and 881B104 (modular) telephone sets (Table A) • Show 881A102, 881A103, and 881A104 telephone sets (MD). Warning: Telephone apparatus or wiring Fig. 1---t8818102 DESIGN LINE Telephone Set. shall not be installed in a location where minimum separation from other wiring as specified in Section 460-300-149 cannot be are equipped with a plug-ended H4DU handset cord maintained. instead of an H4EB cord .• 1.03 The customer's premises must be properly wired with an appropriate connecting block Ordering Guide (Refer to Table A) or jack in order to accept the D4BU-29 plug-ended mounting cord or the 225A adapter shipped with 2.02 Basic Telephone Set Ordering Information: each set. Example: Set, Telephone, 881B102t is an 2. IDENTIFICATION antique gold cradle phone equipped with a rotary dial. 2.01 .The 881A102, B102, 881Al03, B103, 881A104, and B104. (Rotary Dial) equipped telephone tRefer to Table A for available codes and sets are new DESIGN LINE telephone sets being ordering information. made available to the customer. The customer buys the housing and handset from the telephone 2.03 These telephone sets are intended to be company and the telephone company retains used as single line or two-party desk sets ownership of the transmission and signaling and are not recommended for use on four- and components. (Fig. 4 and 5). •The B code sets eight-party service. NOTICE Not for use or disclosure outside the Bell System except under written agreement Printed in U.S.A. Page 1 SECTION 503-200-108 Fig. 2-881A103 DESIGN LINE Telephone Set Fig. 4--Customer-Owned Components 3. INSTALLATION AND CONNECTIONS 3.01 These telephone sets are furnished from the factory fully assembled and wired for bridged ringing. To connect the telephone set, plug the mounting cord into a 625A connecting block or if the existing jack is a 548A or equivalent, use the 225A adapter furnished with each set. 3.02 The internal connections for the 881A102, 8818102, 881A103, 8818103, 881A104, and 8818104 telephone sets, for nonkey system use, are shown in Fig. 9. 3.03 Connections for 1A KTS do not require any telephone set modifications and are wired same as Fig. 9. Fig. 3-881A 104 DESIGN LINE Telephone Set 3.04 Connections for use with 1A1 or 1A2 KTS are shown in Fig. 10. Table C includes necessary wiring modifications required for lAl or 1A2 KTS use. Page 2 ISS 2, SECTION 503-200-1 08 NOTE: ALL LINE OTHER COMPONENTS NOT SHOWN ARE CUSTOMER - OWNED TRANSMITTER CONNECTORS Tl TRANSM ITTER UN IT CA~D HOLDER ASSEMBLY Fig. 5-+Telephone Company-Owned Components. 3.05 To gain access to the interior of these sets 4. REMOVAL OF TELEPHONE COMPANY-OWNED for wiring changes, refer to appropriate COMPONENTS paragraph in Part 4. 3.06 Line and Ringer Connections: 4.01 When it is desired to discontinue telephone service of these DESIGN LINE telephone sets, proceed as follows: (1) For single line and two-party service, refer to Table B. Note: Remove the telephone company-owned components that can be easily removed. Refer (2) For adjustments and ringer cutoff feature to Fig. 5 for identification of company-owned of the P1A ringer, refer to Section 501-259-101. components. Page 3 ;,eCTION 503-200-108 AVAILABLE CODES AND OR DERING GUIDE TEL SET TEL SET TRMTR RCVR MTG HANDSET DIAL DESCRIPTION BASE UNIT CODE UNIT CORD CORD Rotary Dial 881Bl02 H4DU-58 Antique Gold Cradle Phone Rotary Dial 881Bl03 840404941 H4DU-03 Mediterranean Cradle Phone Rotary Dial 881Bl04 H4DU-03 Early American 6U-120 Cradle Phone or Tl LBl D4BU-29 6UA-120 Rotary Dial 881A102* H4EB-58 Antique Gold Cradle Phone Rotary Dial 881A103* SSOA H4EB-03 Mediterranean Cradle Phone Rotary Dial 881A104* H4EB-03 Early American Cradle Phone *MD (1) Remove four bottom cover mounting screws from bottom of telephone set and remove bottom cover (Fig. 6). (2) Remove four telephone set base mounting screws and withdraw the base (Fig. 7). (3) Remove three dial mounting screws and remove the rotary dial (Fig. 8). (4) Unscrew transmitter and receiver caps and remove T1 transmitter and LB1 receiver units. (5) Replace bottom cover (Fig. 6). 4.02 Follow local procedures for returning telephone company-owned components. 4.03 When it is desired to return a set to Western Electric for repair, it should be packed using the D-180600 Kit of Parts which contains packing Fig. 6-881 A 102, 881 A 103 , or 881 A 104 Telephone materials and instructions. Set, Bottom V iew Page 4 ISS 2, SECTION 503-200-108 TELEPHONE SET BASE MOUNTING SCREWS Fig. 8--Removing Dial Fig. 7-Removing Telephone Set Base Page 5 SECTION 503-200-108 TABLE 8 LINE AND RINGER CONNECTIONS t INDIVID. TIP PARTY RING WIRE OR LEAD COLOR OR PARTY NOIDENT IDENTIFYING GROUND BRIDGED GROUND 10000 26500 Inside Wire at R R R R R R Jack G G G G G G y y y y y y BK B B B B B 623P4 Line Jack R A A Ll F F ABsy G Ll Ll A L2 L2 y G G G G G BK L2 L2 L2 * * Ringer R K K K K K S-R * * * * Ll s * * * Ll * BK Ll G G G G Line Switch y A A A L2 L2 w F F F B B * Insulated and stored. t For access to set wiring follow applicable steps in Part 4. TABLE C MODIFICATIONS FOR 1A1 OR 1A2 KTS* NETWORK TERMINAL LEAD COLOR REMOVE CONNECT FROM TO s A L2 y Line A L2 Switch BR c G G Ll A w F c 623P4 Line Jack ABsy G Ll F Ringer BK Ll F * For access to telephone set wiring follow applicable steps in Part 4. · Page 6 INSIDE 625A 4228-TYPE OR 4D10B 60-120 \riiRE CONN. BLK ~~~~CH rt,, NETWORK OR 6UA-120 (NOTE 2) illf DIAL 1H BL '"".J ......, DP NOTES: 'RI I. SET WIRED FOR INDIVIDUAL OR BRIDGED RINGING. (WI 2. LINE SWITCH orr-HOOK SEQUENCE: BK (1) be- MAKES (2) de --MAKES (3) ab- BREAKS :JoN (4) fg - BREAKS 3. THE B CODE SETS ARE EQU I PPED WITH A ~WI MODULAR HANDSET AND PLUG-ENDED w HANDSET CORD. THE A CODES ARE [QUIPPED WITH A CONVENTIONAl HANDSET AND CORD. It- 0----J.ON L INSULATED AND STORED --~. • ~KI DP- DIAL PULSE ON- D 1AL orr-NORMAL HANDSET tWI RC:VR I I I I I tWI I I (RI : ;; I I ""</G I I 0L2 ~MlR ~"' ~ !l Fig. 9-*881A102, 8818102, 881A103, 8818103, 881A104, or 8818104 Telephone Set, Connections. i a: CD I 'II -~ ...aD,.a Ill • § I • i INSIDE 625A 04!1U-29 PIA LINE 4228 ~ T!IP£ :01 ; eu -120 HAHOSET ~IRE COHN. BLK 1623P4 MTG JACK RINGER SWITCH 40108 NET~ 0116UA-Ial) CORD ASSY (NOTE 21 (NOTE I) DIAL -i RING R (R) (R) A I RCVR TIP 'G (G) }Ill ~~ ~~ ·r&- ::::- A l. (Y) ;.~~ . ~ (R) AI 8 (BK) )Ill I~I ~) (G) K d I I Jew! ~)* I (BK) IRI 165011 I NOTES: I. LINE SWITCH orr-- SEQUENCE: _\I (WI I (I) be • MAK£5 t-!!1- * ~ '"\. lwJBK I (2) do • HAK!S • 50011 (3)Db • BREAKS 11 .~ I (4)fg - BREAKS ' ON A, " ' l (W) I 2. Sl"T WillED FOR INDIVIDUAL CR BRIDGED II' liNG. + 3, THE B CODF. SETS ARE EQU"PED WITH A GN./ 1i' (WI OR (G) I MCIOULAR HANDSET AND PLUG-EliDED 50011 RR ~":::1 c:: w HANDSET CCRO, TNE A CODE SETS ARE £QU '1'£1) h WITH A COIIYEIITIOIIAL HAIIDSET AIID CORD c I (IIOTE 31 L- * - IIISULATEO MD STORED ;JoN I I I DP-·DIAL JIULS[ 'ON- DIAL Ol"f•IIOIIIAL B I KI•TYP£ HANDSET I !WI 11CNR (R) l. "'<' I I I (BK) DP I I. I (BK) I ~r (WI I - ~- I I (BR) I c Ao 0 Ll .t_(Y) (Ill : .:+csl }2 ~ fig. 10--t881A102, 8811102, 881A103, 8811103, 881A104, or 8811104 Telephone Set Wired for 1A1 or 1A2 KT~ .