POWERFORCE® HELIX Vacuum ___________ USER GUIDE 1700 & 1701 SERIES (Model 1701 Shown) IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM. Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following: cord, or pull cord around sharp or use in areas where they may edges or corners. Do not run be present. WARNING appliance over cord. Keep cord TO REDUCE THE RISK OF FIRE, » Do not use vacuum cleaner in an away from heated surfaces. enclosed space filled with vapors ELECTRIC SHOCK, OR INJURY: » Do not unplug by pulling on given off by oil base paint, paint » Do not leave vacuum cleaner cord. To unplug, grasp the plug, thinner, some moth proofing when it is plugged in. Unplug not the cord. substances, flammable dust, or from outlet when not in use other explosive or toxic vapors. and before servicing. » Do not handle plug or vacuum cleaner with wet hands. » Do not use to pick up toxic » Do not use outdoors or on material (chlorine bleach, wet surfaces. » Do not put any object into openings. Do not use with any ammonia, drain cleaner, etc.). » Do not allow to be used as a toy. opening blocked; keep openings » Do not pick up anything that is Close attention is necessary when free of dust, lint, hair, and anything burning or smoking, such as used by or near children. that may reduce air flow. cigarettes, matches, or hot ashes. » Do not use for any purpose other » Keep hair, loose clothing, fingers, » Do not use without filters in place. than described in this User’s and all parts of body away from » Do not pick up hard or sharp Guide. Use only manufacturer’s openings and moving parts. recommended attachments. objects such as glass, nails, screws, » Turn off all controls before coins, etc. » Do not use with damaged cord or plugging or unplugging » Use only on dry, indoor surfaces. plug. If appliance is not working vacuum cleaner. as it should, has been dropped, » Keep appliance on a level surface. damaged, left outdoors, or » Use extra care when cleaning » Do not carry the vacuum cleaner dropped into water, have it repaired on stairs. while it is running. at an authorized service center. » Do not use to pick up flammable » Unplug before connecting or dis- » Do not pull or carry by cord, use or combustible materials (lighter connecting the TurboBrush® Tool. cord as a handle, close a door on fluid, gasoline, kerosene, etc.) SAVE THESE INSTRUCTIONS This model is for household use only. WARNING ›› Plastic film can be dangerous. To avoid danger of suffocation, keep away from children. ›› Do not plug in your vacuum cleaner UNTIL you are familiar with all instructions and operating procedures. ›› To reduce the risk of electrical shock, turn power switch off and disconnect polarized plug from electrical outlet BEFORE performing maintenance or troubleshooting checks. Hot THIS APPLIANCE HAS Neutral A POLARIZED PLUG To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way. 2 www.BISSELL.com Thanks for buying a BISSELL vacuum! We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your vacuum works as well in one year as it does today, so this guide has tips on using (page 6-7), maintaining (pages 7-9), and if there is a problem, troubleshooting (page 10). What’s in the Box? Upper Handle User Guide Dusting Crevice Brush Tool stored inside extension wand Base Unit Lower Cord Wrap Hose Extension Wand TurboBrush® 2 Screws Tool (Model 1701 Only) taped to handle (Model 1701 Shown) NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap. Safety Instructions...........2 Troubleshooting ............10 Product View................4 Warranty ....................11 Assembly ...................5 Service ......................11 Operations ................6-7 Contact Information ........12 Maintenance & Care .......7-9 Product Registration........12 www.BISSELL.com 3 Product View (Model 1701 Shown) 1 10 2 11 3 12 4 13 5 14 15 9 6 7 16 17 8 18 19 20 21 1 Upper Handle 11 Hose Clip 2 TurboBrush® Tool (1701 Series Only) 12 Upper Quick Wrap Release™ Cord Wrap 3 Tank Release Button 13 Crevice Tool 4 Carry Handle 14 Power Cord 5 Washable 15 Extension Wand Pre-Motor Filter 16 Lower Cord Wrap 6 Dirt Container 17 Hose Wand 7 Dirt Container Empty Button 18 Power Switch Pedal 8 Washable Post-Motor Filter (1701 Series Only) 19 Handle Recline Pedal 9 Dusting Brush 20 Foot Hose 10 Cord Hook 21 Product Rating Label & Serial Number 4 www.BISSELL.com Assembly WARNING Do not plug in your vacuum until you are familiar with all instructions and operating procedures. 1 2 First, place the upper handle onto the base and push it Next, insert the down. Then attach lower cord wrap the handle with the and turn it to 2 screws that are the left to lock taped to the handle it into place. in a plastic bag. 3 4 Then wrap the power cord around Next, insert the the cord release end of the hose clips and clip the into the back of end of the plug to the vacuum and the power cord. twist to lock it into place. 6 Put your accessory tools on the 5 Now wrap vacuum and you’re ready to go! the hose through the hose clip and connect the hose wand to the foot hose down at the bottom of the vacuum. Extension Wand (with Crevice Tool inside) Dusting Brush TurboBrush® Tool NOTE: The crevice tool can be found inside the extension wand. You can remove it to use it and put it back to store it neatly out of your way when you’re finished. www.BISSELL.com 5 Using Your Cleaner 1 2 Press the recline pedal to lean your vacuum Press the red power switch with your back for cleaning. To get even lower, press foot to turn on your vacuum. Press it the recline pedal a second time. When again to turn your vacuum off when you’re finished, lean it all the way back up to you’ve finished cleaning. lock it into the upright position. Using the Height Adjustment You can easily raise or lower your vacuum to adjust to different flooring types. Simply turn the knob towards the desired flooring type. If your vacuum becomes too difficult to push, just move to a higher setting. NOTE: Some frieze and berber carpets have long delicate fibers or threads that may be damaged by rotating brush. Repeated strokes in the same area may enhance this condition. WARNING Before using your vacuum, make sure that the dirt container is in locked position and that all filters, both pre and post-motor filters are in place. DO NOT operate your vacuum without these filters. WARNING The rotating floor brush continues to rotate while tools are in use. To reduce the risk of injury from moving parts, always move the cleaner with the carry handle at the front of the unit. Always place the cleaner on the floor with the handle in the upright position when using tools. Never place your fingers under the cleaner when it is running. Never place the powerfoot on furniture or uneven surfaces. Do not place vacuum cleaner close enough to objects to pull them into rotating brush. To prevent carpet damage, do not lean on the vacuum or let the powerfoot tilt forward. 6 www.BISSELL.com Using the Specialized Tools Dusting Brush Crevice Tool Extension Wand TurboBrush® Tool (Model 1701 Only) Your new PowerForce Helix vacuum not in the upright position, pick the accessory only does a great job on your floors, tool that best fits your needs and attach it also comes with a complete set of it to the end of your hose. You’re ready accessory tools to make your above floor to clean base boards, curtains, upholstery cleaning jobs easier. Just put your vacuum and much more. Maintaining the TurboBrush® Tool NOTE: TurboBrush only comes standard with 1701 series. Align 1 Slot 2 3 Paddle Wheel Roller Belt Twist gray collar counter- clockwise, until slot appears then separate If paddle wheel gets The faceplate will not faceplate. Carefully dislodged, align the two close properly if all remove brush, replace clips on each side and parts are not aligned belt and brush if needed. pop into place. correctly. Parts & Supplies For Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field. www.BISSELL.com 7 Emptying the Dirt Container 1 2 Holding dirt con- tainer over a trash bin, press release button on back to open tank bottom and dump the Press tank release debris. button and pull handle Snap bottom to lift dirt container back into place away from vacuum. when empty. Cleaning the Pre-Motor Filter 1 2 3 Press tank Remove the release pre-motor filter by button and pulling it from the pull handle Open the dirt tank lid. Clean it to lift dirt container lid with warm water.