© ISO 2014 – All rights reserved ISO/TC 104/SC 04 Date: 2014-08-05 ISO/DIS 9897-1 ISO/TC 104/SC 04/WG 03 Secretariat: ANSI Freight containers — Container equipment data exchange (CEDEX) — Part 1: General communication codes for general purpose containers Conteneurs pour le transport de merchandises — Échange de données sur les équipements de conteneurs (CEDEX) — Partie 1: Codes des communications générales Warning This document is not an ISO International Standard. It is distributed for review and comment. It is subject to change without notice and may not be referred to as an International Standard. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. Document type: International Standard Document subtype: Document stage: (40) Enquiry Document language: E H:\Abteilungs Archiv\Geschichtsakte FAKRA-Normen\Normen_05001-10000\09897\Part 1\03_DIS und FDIS\ISO_DIS 9897-1_(E) 2014-08-05.doc STD Version 2.5a ISO/DIS 9897-1 Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be repro- duced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. ii © ISO 2014 – All rights reserved ISO/DIS 9897-1 Contents Page 1 Scope ...................................................................................................................................................... 1 2 Normative references ............................................................................................................................ 1 3 Principle.................................................................................................................................................. 1 4 Data elements and codes ..................................................................................................................... 2 4.1 Data elements ........................................................................................................................................ 2 4.2 Data assignments .................................................................................................................................. 2 4.3 Updating data elements ........................................................................................................................ 4 Annex A (normative) Code - Message types .................................................................................................. 5 Annex B (normative) Structural condition, repair condition, outside coating, inside coating, full /empty indicator ..................................................................................................................................... 6 B.1 Structural condition, repair condition, outside coating, inside coating .......................................... 6 B.2 Full/empty indicator .............................................................................................................................. 6 Annex C (normative) Damage Location .......................................................................................................... 7 C.1 Location coding convention................................................................................................................. 7 Annex D (normative) Damage types .............................................................................................................. 12 Annex E (normative) Material types .............................................................................................................. 16 Annex F (normative) Repair types ................................................................................................................. 17 Annex G (normative) Measure unit specifier, repair size dimension and work scales ............................ 21 G.1 Measure unit specifier ......................................................................................................................... 21 G.2 Size of repair ........................................................................................................................................ 22 G.3 Scale ..................................................................................................................................................... 22 Annex H (normative) Responsibility .............................................................................................................. 23 Annex I (normative) Components of the general purpose container......................................................... 24 I.1 Components of general purpose containers .................................................................................... 24 I.2 Components applicable to marking .................................................................................................. 33 I.3 Miscellaneous ...................................................................................................................................... 35 Bibliography ...................................................................................................................................................... 41 © ISO 2014 – All rights reserved iii ISO/DIS 9897-1 Foreword This first edition of ISO 9897-1, together with ISO 9897-2, ISO 9897-3, ISO 9897-4, ISO 9897-5 and ISO 9897-6, cancels and replaces ISO 9897:1997. Together with a thoroughly technical revision of the ISO 9897:1997, this international standard have been split into parts to simplify and relate the technical content of each part to each type of container and also, as far as possible, to harmonize the parts of ISO 9897 with the order of container types as contained in the parts of ISO 1496. ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Interna- tional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Interna- tional Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9897-1 was prepared by Technical Committee ISO/TC 104, Freight containers, Subcommittee SC 04, Identification and communication. This first edition of ISO 9897-1, together with ISO 9897-2, ISO 9897-3, ISO 9897-4, ISO 9897-5 and ISO 9897-6, cancels and replaces ISO 9897:1997. Together with a thoroughly technical revision of the ISO 9897:1997, this international standard have been split into parts to simplify and relate the technical content of each part to each type of container and also, as far as possible, to harmonize the parts of ISO 9897 with the order of container types as contained in the parts of ISO 1496. ISO 9897 consists of the following parts, under the general title Freight containers — Container equipment data exchange (CEDEX): Part 1: General communication codes for general purpose containers Part 2: Refrigerated containers Part 3: Tank Part 4: Special purpose containers Part 5: Chassis Part 6: Message sets for data transfer between trading partners and systems iv © ISO 2014 – All rights reserved DRAFT INTERNATIONAL STANDARD ISO/DIS 9897-1 Freight containers — Container equipment data exchange (CEDEX) — Part 1: General communication codes for general purpose containers 1 Scope This International Standard specifies general communication codes for container equipment data exchange (CEDEX). It is intended for business entities for use in communications relating to freight container transactions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer- ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3166:1993, Codes for the representation of names of countries ISO 6346:1995, Freight containers — Coding, identification and marking ISO 9897-6:2010, Freight containers — Container equipment data exchange (CEDEX) — Message sets