Page 1 of 23 - DIN EN ISO 4628-1: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform changes in appearance - Part 1: General introduction and evaluation system. - DIN EN ISO 4628-2: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform changes in appearance - Part 2: Evaluation of degree of blistering - DIN EN ISO 4628-3: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting - DIN EN ISO 4628-4: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform change in appearance - Part 4: Assessment of degree of cracking - DIN EN ISO 4628-5: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking - DIN EN ISO 4628-6: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform change in appearance - Part 6: Assessment of degree of chalking by the tape method - DIN EN ISO 4628-7: Paints and varnishes - Evaluation of coating damage - Assessment of quantity and size of damage and intensity of uniform change in appearance - Part 7: Assessment of degree of chalking by velvet method - DIN EN ISO 4628-8: Paints and varnishes - Evaluation of coating damage - Evaluation of the amount and size of damage and the intensity of uniform changes in appearance - Part 8: Evaluation of delamination and corrosion caused by scoring or other artificial damage - AWN 060501: Cleanliness requirements for hydraulic components and systems - DIN EN ISO 2360: Non-conductive coatings on non-magnetic metallic base materials - Measurement of coating thickness - Eddy current method - DIN EN ISO 2409: Coating materials - Cross-cut test - DIN EN ISO 2808: Paints and varnishes - Determination of film thickness - DIN EN ISO 2812-1: Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water - DIN EN ISO 2812-2: Paints and varnishes - Determination of resistance to liquids - Part 2: Method with immersion in water - DIN EN ISO 2812-3: Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent material - DIN EN ISO 2812-4: Part 4: Drip/spot methodCoatings materials - Determination of resistance to liquids - Part 4: Drip/spot method - DIN EN ISO 2812-5: Paints and varnishes - Determination of resistance to liquids - Part 5: Gradient oven method - DIN EN ISO 2813: Paints and varnishes - Determination of gloss at 20°, 60° and 85 Page 2 of 23 - DIN EN ISO 6270-1: Paints and varnishes - Determination of resistance to moisture - Part 1: Condensation (one-sided exposure) - DIN EN ISO 6270-2: Paints and varnishes - Determination of resistance to moisture - Part 2: Condensation (exposure in a climatic chamber with heated water tank) - DIN EN ISO 6272-1: Paints and varnishes - Test for resistance to impact deformation (impact test) - Part 1: Falling weight test, large test area - DIN EN ISO 6272-2: Paints and varnishes - Test for resistance to impact deformation (impact test) - Part 2: Falling weight test, small test area - DIN EN ISO 6860: Paints and varnishes - Mandrel bending test (with conical mandrel) - DIN EN ISO 9227: Corrosion tests in artificial atmospheres - Salt spray tests - DIN EN ISO 15184: Paints and varnishes - Determination of hardness of coatings by pencil testing - DIN EN ISO 20567-1: Paints and varnishes - Testing of stone impact resistance of coatings - Part 1: Multi- impact test - VDA-19: Testing of technical cleanliness - Particle contamination of functionally relevant automotive parts - ISO 4406: Hydraulic fluid power - Fluids - Method for coding the level of contamination by solid particles - ISO 16232-1: Road vehicles - Cleanliness of components of fluid circuits - Part 1: Vocabulary - ISO 16232-2: Road vehicles - Cleanliness of components of fluid circuits - Part 2: Method of extraction of contaminants by agitation - ISO 16232-3: Road vehicles - Cleanliness of components of fluid circuits - Part 3: Method of extraction of contaminants by pressure rinsing - ISO 16232-4: Road vehicles - Cleanliness of components of fluid circuits - Part 4: Method of extraction of contaminants by ultrasonic techniques - ISO 16232-5: Road vehicles - Cleanliness of components of fluid circuits - Part 5: Method of extraction of contaminants on functional test bench - ISO 16232-6: Road vehicles - Cleanliness of components of fluid circuits - Part 6: Particle mass determination by gravimetric analysis - ISO 16232-7: Road vehicles - Cleanliness of components of fluid circuits - Part 7: Particle sizing and counting by microscopic analysis - ISO 16232-8: Road vehicles - Cleanliness of components of fluid circuits - Part 8: Particle nature determination by microscopic analysis - ISO 16232-9: Road vehicles - Cleanliness of components of fluid circuits - Part 9: Particle sizing and counting by automatic light extinction particle counter - ISO 16232-10: Road vehicles - Cleanliness of components of fluid circuits - Part 10: Expression of results Page 3 of 23 - MAN M 3652: Technical cleanliness of fluid lines for use in commercial vehicles - SAE J400: Test for chip resistance of surface coatings - DIN EN ISO 2178: Non-magnetic coatings on magnetic base metals - Measurement of coating thickness - WN0004: Component / System Cleanliness - DIN 50018: Testing in a condensation water alternating climate with an atmosphere containing sulfur dioxide - DIN 53504: Testing of rubber and elastomers - Determination of tensile strength, tensile elongation and stress values in the tensile test - DIN 53508: Testing of rubber and elastomers - Artificial aging - DIN 53512: Testing of rubber and elastomers - Determination of rebound elasticity (Schob-Pendel) - DIN EN 438-2 Decorative high-pressure laminates (HPL) - Boards based on curable resins (laminates) - Part 2: Determination of properties - DIN EN 660-2: Resilient floor coverings - Determination of wear characteristics - Part 2: Frick-Taber test - DIN EN 1067: Adhesives - Examination and preparation of specimens for testing - DIN EN 1518: Non-destructive testing - Leak testing - Characterization of mass spectrometric leak detectors - DIN EN 13523-6: Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test) - DIN EN 15042-2 Coating thickness measurement and characterization of surfaces by means of surface waves - Part 2: Guideline for photothermal coating thickness measurement - DIN EN 15184: Products and systems for the protection and repair of concrete structures - Test methods - Adhesive tensile strength between coated steel and concrete - DIN EN 60068-2-7: Environmental tests - Part 2: Tests Ga and guide; Uniform acceleration - DIN EN 60068-2-10: Environmental tests - Part 2-10: Test methods - Test J and guidance: Mold growth - DIN EN 60068-2-11: Environmental tests - Part 2: Tests - Test Ka: Salt spray - DIN EN 60068-2-13: Environmental tests - Part 2: Tests - Test group M: Low air pressure - DIN EN 60068-2-17: Environmental tests - Part 2: Tests - Test Q: Tightness - DIN EN 60068-2-20: Environmental tests - Part 2-20: Tests - Test T: Test method for solderability and solder heat resistance of components with led out terminals Page 4 of 23 - DIN EN 60068-2-21: Environmental tests - Part 2-21: Tests - Test U: Resistance of terminals and integral fasteners - DIN EN 60068-2-30: Environmental tests - Part 2-30: Test methods - Test Db: Damp heat, cyclic (12 + 12 hours) - DIN EN 60068-2-40: Environmental tests - Part 2: Tests - Test Z/AM: Combined cold/low air pressure test - DIN EN 60068-2-41: Environmental tests - Part 2: Tests - Test Z/BM: Combined test - DIN EN 60068-2-42: Environmental tests - Part 2¬42: Tests - Test Kc - Sulfur dioxide for contacts and connections - DIN EN 60068-2-43: Environmental tests - Part 2¬43: Tests - Test Kd: Hydrogen sulfide for contacts and connections - DIN EN 60068-2-45: Environmental testing - Part 2; Tests - Test XA and guide: Immersion in liquid detergents - DIN EN 60068-2-47: Environmental tests - Part 2-47: Test methods - Mounting of test specimens for vibration, impact and similar dynamic tests - DIN EN 60068-2-48: Environmental tests - Part 2-48: Tests - Guideline for the application of tests according to - DIN EN 60068-2-61: Environmental tests - Part 2-61: Test methods - Test Z/ABDM: Sequence of climatic tests - DIN EN 60068-2-66: Environmental tests - Part 2-66: Test methods - Test Cx: Humid heat, constant (unsaturated pressurized steam) - DIN EN 60068-2-67: Environmental tests - Part 2-67: Tests - Test Cy: Damp heat, constant, accelerated test, preferably for construction elements - DIN EN 60068-2-68: Environmental tests - Part 2-67: Tests - Test L: Dust and sand - DIN EN 60068-2-70: Environmental tests - Part 2-70: Tests - Test Xb: Test of resistance of markings and inscriptions to abrasion caused by wiping with fingers and hands - DIN EN 60068-2-77: Environmental tests - Part 2-77: Tests - Test 77: Body strength and impact test - DIN EN 60068-2-80: Environmental tests - Part 2-80: Test methods - Test Fi: Mixed-mode vibration test - DIN EN 60068-2-81: Environmental tests - Part 2¬81: Tests - Test Ei: Shock . Synthesis of shock response spectrum - DIN EN 60068-2-82: Environmental