For other conversion kits, please visit our website at www.simunition.com NonNon-lethal FX FX® Colored® Lethal CQT® ® SIMUNITION CONVERSION KIT ® ® GEN 1 colored Black STAND-OFF TRAINING DISTANCES FOR FX MARKING CARTRIDGES ONLY: The FX 9000 Series protective equipment has been designed and tested under FN SCAR RIFLE and sub compact carbine, 5.56mm cal. rigorous laboratory conditions to resist impact from all FX® Marking Cartridges. General Dynamics Ordnance and Tactical Systems Canada strongly recommends the following minimum stand-off training distances when firing at protected personnel*: 1-foot (30cm) for 9mm FX ® and .38 cal. FX® Marking cartridges, 3-foot (1m) for 5.56mm FX® Product : 5314610 FNSCAR SC (fixed handle) Marking cartridges clipped and 6-foot (2m) for 5.56mm FX® Marking cartridges linked. Due to the nature of the FX® training system, end users must refer to their 5314620 FNSCAR-L respective in-service training guidelines and regulations for the authorized force-on-force stand-off distances. * Protected personnel are defined as personnel using approved mandatory FX® head, throat and groin protection ( no exposed skin when using 5.56mm FX® Marking Cartridges). 5314630 FNSCAR-L (fixed handle) The FX® 8000 Series protective equipment may still be used with 9mm FX® and .38 cal. FX® Marking cartridges only. Handling and Safety Instructions WARNING WARNING Use of this product without the mandatory A1 Not for use against human targets A1 safety equipment can result in serious injuries WARNING A2 A2 IMPROPER USE CAN CAUSE SERIOUS INJURY OR DEATH. Fig. I This product requires the same firearm handling precautions as standard firearms. Use only with firearms in good conditions. Keep barrel free of any Simunition® 5.56 mm FX® Marking ® A3 obstructions. Use Simunition conversion kit only in appropriate models and calibers of firearms as indicated on the conversion barrel, bolt, and/or slide. If Cartridges A3 the gun fails to fire, avoid exposure to the breech when unloading and point the muzzle in a safe direction. Wear approved eye and ear protection as Simunition® 5.56 mm CQT® required. The manufacturer shall not be liable for injuries or damage resulting from the use of this conversion kit. Fig. II Cartridges KEEP OUT OF REACH OF CHILDREN. Before handling the weapon, read the following instruction ! Be aware that a firearm converted with this Simunition® conversion kit, like all firearms, if handled in a careless or reckless manner can be dangerous and lethal. Consequently, the Simunition® conversion kit accompanying these Handling and Safety Instructions has been sold under the express understanding Intended only for supervised training conducted in accordance with that the manufacturer of this conversion kit declines any responsibility for consequences arising out of either intentional or accidental discharge of firearms Simunition® safety training protocols by Law Enforcement, Military and and ammunitions used with this conversion kit, or from its function when used for purposes or subjected to treatment for which it was not designed. Simunition® approved Commercial Range Programs. lt is mandatory that Simunition® converted weapons be clearly identified as such, before any training takes place. A good practice is to use blue tape for FX® ® ® and SecuriBlank ammunition and yellow tape for CQT ammunition on the weapon trigger guard, grip and butt stock. After training, kits and weapons must The safe use of Simunition® 5.56 mm reduced energy Cartridges in the FN be thoroughly cleaned and lightly lubricated to avoid potential functioning problems. Remove colored tape as applicable. SCAR weapons requires the installation of a Simunition® conversion bolt & bolt ONLY FX® and SecuriBlank® are NON-LETHAL, CQT® is CONSIDERED LETHAL ® Fig. III - Part B carrier assembly. Proper installation of the bolt/bolt carrier assembly is required The Simunition bolt/bolt carrier assembly is designed to diminish the possibility of firing a live 5 56x45mm cartridge by having a bolt rim diameter smaller ® than the live cartridge case rim diameter. This smaller bolt rim diameter keeps the live cartridge from seating properly on the bolt face thus preventing the Simunition Cleaning Kit to help preclude the inadvertent chambering and firing of live, lethal operational firing pin from reaching the live cartridge primer. ln the event that a live 5.56x45mm cartridge was inadvertently loaded in a magazine or in the weapon’s ammunition and ensure the proper operation and cycling of the weapon. chamber, it will chamber but will not seat properly on the bolt face, thus preventing the firing pin from striking the primer, a failure to fire will be observed, point muzzle in a safe direction, put fire control selector lever on safe, remove magazine, pull the charging handle and Iock bolt back, keep fingers away from For safety reasons, Simunition® conversion bolt & bolt carrier assemblies are ejection port, magazine well and trigger, if live cartridge did not eject and is stuck on bolt head, remove cartridge from bolt head using a small wooden stick manufactured from the same quality materials as the original service or flat screwdriver, if the cartridge is stuck in the chamber, do not rack bolt to remove it, the weapon must be taken apart, point muzzle in a safe direction, using the charging handle ride the bolt forward slowly until it stops against the cartridge head, make sure the fire control selector lever is on safe, do not components they replace, but are visually different to help distinguish them from touch trigger, remove both the front and rear take down pins, take the upper receiver away from the lower receiver, remove bolt/bolt carrier assembly and operational bolt & bolt carrier assemblies. charging handle from upper receiver, remove cartridge from chamber by pushing against the buIlet from the muzzle using a cleaning rod or a wooden rod. Clean weapon and conversion kit, visually and physically inspect that no cartridge are present in chamber and in receivers (upper and lower), re-assemble Fig. IV - Part C ® weapon as per manufacturer's recommendations. Blue Barrel Indicator The Simunition conversion kit for FN SCAR weapons consists of four (4) items: Considering the great variety of cartridges and projectiles of different calibers available on the world commercial rnarket, it is impossible for General ® Dynamics-OTS Canada to warrant that none of those cartridges will be precluded from firing in a Simunition - converted weapon such that the projectile will Part A: Simunition® Bolt & Bolt Carrier Assembly (Fig. II) not exit the barrel. Models : A1 = FN SCAR SC (fixed handle), A2 = FN SCAR-L, A3 = FN SCAR-L (fixed All Simunition® conversion kits are made to fire Always On Target CQT® ammunition, these cartridges are lethal. handle). WARRANTY: General Dynamics Ordnance and Tactical Systems Canada Inc. (General Dynamics-OTS Canada) warrants that the Simunition® conversion kits and associated components or accessories shall be free from defects in material or workmanship under normal use during the Warranty Period. During the Warranty Period, Part B: Simunition® Cleaning Wire Kit (Fig. III) (part number 5308438SP) General Dynamics-OTS Canada will repair or replace, at no charge, products or parts of a product that proves defective because of improper material or workmanship, (Brushes only, part number 5308436SP BRONZE BRUSH ® under normal use and maintenance. The Warranty Period for the Physical Goods purchased from General Dynamics-OTS Canada or approved Simunition Distributors (2un.) .243/.25CAL RIFLE) is 60 months (5 years) or 10 000 rounds fired, whichever comes first, from the date of purchase. LIMITATION ON WARRANTY: Simunition® conversion kits are designed to fire Simunition® Reduced Energy cartridges only (FX® marking rounds, Securiblank® Fig. V - Part D Part C: Blue Barrel Indicator (Fig. IV) (part number 5308499SP) ® ® training blanks and CQT force on target training rounds). Use of Simunition conversion kit with any other kind or brand of ammunition shall void the warranty. Normal FX® Projectile extractor tool ® wear and tear is not covered by this warranty. Part D: FX Projectile extractor tool (Fig. V) (part number 5311840SP) In order to obtain warranty service, the purchaser/user must first fill out a warranty service request in order for General Dynamics-OTS Canada to determine the XXXXXXXSP= Spare part available from General Dynamics Ordnance and Tactical-Systems Canada problem and the most appropriate action. The warranty service requests can be found on our website at the following link: http://simunition.com/en Canada General Dynamics Ordnance and Tactical Systems-Canada Inc. 5 Montée des Arsenaux, Repentigny, Québec, Canada J5Z 2P4 12 - Trademarks and registered trademarks of General Dynamics Tel.: 1-450-581-5999 E-mail : [email protected] 2017 Ordnance and Tactical Systems-Canada Inc. are denoted by TM Management System certified to ISO 9001, ISO 14001, OHSAS 18001 ® and respectively. US General Dynamics Ordnance and Tactical Systems-Simunition ® Operations P. O. Box 576, Avon, CT 06001-0576 USA © 2016 General Dynamics-OTS Canada Toll free US only : 1-800-465-8255 ; 1-860-404-0162 Fax: 1-860-404-0169 E-mail : [email protected] Web site www.simunition.com inPrint CANADA 5314611.FTSIM (rev.00) Installation Loading Magazines Warning: Never load 5.56mm FX Gen 1 and 5.56mm FX Refer to t h e s e Simunition® weapon conversion kit technical Gen 2 cartridges in the same magazine. Do not use 5.56mm instructions and weapon OEM factory guidelines. FX Gen 2 after firing 5.56mm FX Gen 1 unless the barrel has Projectile Projectile been cleaned to remove residues left by firing of 5.56mm FX Gen. 1 Gen. 2 1. Point the muzzle of the weapon in a safe direction, put fire control selector lever on Gen 1. safe and remove the magazine. With the charging handle recoil the bolt/bolt carrier ® assembly to extract any unfired cartridges and lock bolt with the bolt catch/release The standard issue service magazines will accept Simunition 5.56 mm reduced energy.